Search Documents

By Peter C. Jones

The paper gives a broad view of the maintenance procedures at the Cassiar Asbestos Corporation property. Comparisons are drawn to indicate the changes in facilities and approach that have evolved over the last 25 years while coping with the northern British Columbia climatic conditions. Special emphasis has been placed on the importance of the support groups providing services for both the mine site and the town.

Jan 1, 1978

By GEO M. FOWLER

AN appraisal of the activities of the mining geologists during 1936 clearly indicates the ever in- creasing utilization of geology in the search for ore. Few men with geo- logic training are idle at present; this is particularly true regarding recent graduates. Many have accepted employment in distant fields, such as the Philippines and South America, and greatly increased mineral production from these places reflects their activities. In North America, regions of intense mineralization formerly important are being restudied in greater de- tail and with better understanding; as a result, new mineral wealth is being found in many such districts. Much is being done by private companies and individuals, and it is to be hoped that mining companies will increasingly make available the purely scientific results of such studies by permitting their geologists to publish. On such generosity to a large extent will future advances in ore finding depend.

Jan 1, 1937

By C. E. Williams

THE Iron and Steel Division, A.I.M.E., is unique in this country in that it serves all phases of the iron and steel industries. Through its publications, its meetings, and its sponsorship of new technical developments in the industries, it has proved of great value. The various technical committees of the Division are the nucleus around which this service can be developed. The Blast Furnace and Raw Materials Committee has done excellent work. The need for beneficiation of iron ores is increasing and the economics of this operation are developing more and more in favor of increased activities. Ores that are slightly undergrade should be concentrated up to grade to supplant the present practice of mixing with higher-grade ores to bring up the average composition. Marginal ores that are not now being mined, or that are being mined and piled for future use, should be concentrated. The development of the use of sinter in the blast furnace, because of the elimination of fines, the advantage of better sizing of the charge, the resulting reduction of coke consumption, and increased output of pig iron per furnace, will make concentration and sintering become practical ahead of its natural time.

Jan 1, 1936

By Alicia O'Reardon

DIFFIDENTLY, because don'ts are rarely greeted with cheers; humbly, because I, myself, have never lined up with the irreproachables, I venture on the subject of manners for the mining camp matron. Mining camps can be divided roughly into two types-the large, opulent settlement that blooms like the rose about a strong mine in full operation; and the puny group of adobe huts, or calamina shacks, or even canvas tents flung down in the wilderness to shelter the gay pioneers of a shining prospect or the shattered survivors of a lost hope. Of the first, I know nothing; but in the second, I have spent some of my best years, and from its curious code of morals and manners, its comic hates and its unreasoning loves, its high impatience and its engulfing kindness, I have charted the narrow .and pitted path which must be trod by the woman who would success¬fully live therein.

Jan 1, 1936

By Raymond B. Ladoo

The uses for which ground talcs are suited closely depend upon their physical and chemical properties , but , in spite of this fact , little scientific investigation has been made in order to devise quick and accurate tests for the determination of these properties . The chemical properties of talc are inherent and may not be altered or modified except by selective mining or by chemical processes not practical in the present status of the industry . However , the determination of chemical properties is not so important , for most uses , as of physical properties , although sometimes certain chemical characteristics are perhaps unduly insisted upon by chemists in some industries . Physical properties are dependent both upon mineralogical characteristics and upon methods of grinding and sizing and may thus be partly changed or modified by changes in practice . There is so little known of the chemistry and physics of the various processes in which talc is used that the purchase and sale of talc is governed more by rule- of- thumb methods dependent upon individual opinion and often , prejudice , than by accurate , standard tests . This not only causes unwarranted price fluctuations , but injures both the producing and consuming industries by creating false ideas of the suitability of talc for various uses . It thus seems important that present tests be standardized and made uniform for the whole industry , and that new tests devised to fill the existing gaps .

Jul 1, 1920

An extensive laboratory grinding study was carried out on a magnetite ore in order to assess the grinding behaviour of magnetic concentrate and tail from low intensity magnetic separation (LIMS).The test work involved Bond ball mill testing, rod milling, low intensity magnetic separation (LIMS), and batch ball milling down to product sizes of around P80~25 microns. A total of 18 Bond tests and over 150 batch grinding tests and sieve sizing were carried out. Throughout the grinding tests, power draw was continuously monitored. The relationship between the grinding energy and product size was analysed using the conventional energy-size concepts. It was found that the Rittinger equation fits the experimental data well. However, Bond?s equation does not fit the experimental data well, and therefore a modified Bond equation was developed. Differences in grinding properties between the magnetic and non-magnetic component were analysed and compared to the bulk ore. It was found that grinding properties differ significantly and therefore separate grinding test work may be required for each grinding step in the magnetite ore beneficiation flowsheet. Keywords: grinding, iron ores, particle size, modelling.

Jan 1, 2010

By R. F. Favreau, Patrice Favreau

"A blast with explosives creates vibration waves in the zone around the blast.The prediction of the intensity of vibrations is important because people in the cinity demand that the vibrations do not disturb them, and society imposes limits on the vibrations. The U. S. Bureau of Mines (USBM) showed that the easurement of the particle velocity U predicts the risk of damage from vibrations. A currentapproach of blasters to monitor vibrations is to measure them with a seismograph at several distances S, and create a graph of U vs. S and the explosive charge “W” according to the equation U = K / (S / W)N where K and N are constants that depend on the blast method and the nature of the ground over the distance S. Though useful, this equation is empirical, and the results predicted from it are very variable, as shown by figure 1 which indicates that a prediction of U can deviate significantly from the actual value. Moreover, a minimum of two seismograph measurements at two values of S are required to establish the curve. However, here now exists another very convenient method to predict U; it is with the simulator Vibmas, which is based on the fundamental principles of how a blast reates vibrations. This simulator takes into account not only W but rather all the blast parameters, the type of explosive and the properties of the rock. Moreover, to establish the calculation of U as a function of S, only one seismograph measurement is required rather than two as for the USBM method. This last difference is important because it makes it easy to predict U not only as a function of S, but also as a function of the orientation of S. On the site this allows much safer control of the vibrations, and the use of larger explosive charges which reduce excavation costs. The article presents results from a field case at a hydroelectric project in Canada, where the deviation was very moderate. Use of this vibration simulator on the Web is very easy."

Jan 1, 2015

By Dean Bray

During the past three years, a new rear-dumping dragline bucket technology has been patented, developed and tested at North Dakota coal mines. Field testing has shown that this new concept in dragline bucket technology can improve strip-mining efficiencies by reducing cycletimes and increasing dumping radius. This article details the process, participants and the results for the development of a rear-dumping dragline bucket. Participants in the process In November 1995, the board of directors of Dakota Coal authorized the execution of a field test and option agreement and a license agreement with the partnership of D.F. Schmidt, electrical/maintenance supervisor, and Bill Lengenfelder, president of Modern Industrial. The board also authorized entering into a dragline bucket field-testing agreement with the Falkirk Mining Co.

Jan 1, 1999

Six years ago it was my responsibility to give the presidential address, and now that privilege has come my way again. On that occasion we were gathered atWhyalla and I took the opportunity of putting before members some observations on the problems we then faced in Australia, and some gains we had been able to chalk up during those early postwar years. You may recall that we were then just beginning to emerge from the difficulties of postwar reconstructions - of fuel and power shortages, and a grossly inadequate manpower for the tasks facing us. The expansion of manufacturing industry in Australia greatly stimulated by wartime activities, and by the postwar developments of many institutions - ran ahead of the supporting services and of the supply of labour to do thejobs. For many industries this unfortunate state of affairs had meant operating at rates well below their installed capacities and therefore levels of output insufficient for Australia's rapidly growing needs. When I last spoke to you these problems were still with us, though their intensity was beginning to lessen as a result of vigorous efforts by industry and governments to reduce them. But I must confess that my thoughts on that occasion were full of those problems and of the effect they were having on the iron and steel industry of this country-of the coal shortage, the labour shortage, and the many other difficulties we were then faced with - and all at a time when the stepping up of our postwar expansion programme was of vital concern to all of us.What a different picture it is six years later! How greatly has the scene changed for the better. In 1951 Australia's postwar immigration programme was only in...

Jan 1, 1957

Early American history is filled with records of the search for and extraction of minerals-a Northwest passage to the treasures of the Indies-an overland route to the goldfields of California. Mining and its associated minerals industry have heralded advancing civilization throughout the ages. The two basic resources on which we all depend for our food, clothing, shelter, and other comforts are agriculture and minerals. Our endowment and how we use it; the spirit and industriousness of our people; our form of social organization all converge to make up our standard of living-our way of life.

Jan 1, 2012

By J. R. Koehler

Although two-entry yield pillar-based gate roads supported by wooden cribs have been commonly used throughout longwalling in the Wasatch PlateadRoan Cliffs coalfield of central Utah, a three-entry yield-abutment gate road configuration was recently trialed in the Hiawatha Seam at the Genwal Resources (GRI) Crandall Canyon No. 1 Mine, near Huntington, UT. Pillar, entry, and cable bolt performance were monitored through second panel mining using a fairly extensive array of geomechanical instruments installed over a span of four crosscuts. Ground pressure and entry closure measurements confirmed that the 9.1-m-wide (30-ft) yield pillar was partially shielded from first panel longwall loads by the 36.6-m-wide (120-ft) abutment pillar, and consequently, experienced only minor yielding until the approach of the second panel face. Complete yielding of the 9. I-m-wide (30-ft) pillar occurred when the second panel was approximately 6.1 m (20 ft) inby the instrumentation site. Average cable bolt loads and differential roof sag remained low through second panel mining and tailgate entry ground conditions were excellent; however, very high ground pressures in the abutment and yield pillars, and second panel rib strongly suggest a high potential for coal bumps utilizing this gate road configuration at mining cover depths in excess of 396 to 457 m (1300 to 1500 ft). This conclusion is supported by the suspected occurrence of small coal bumps along the abutment pillar ribs, observed indirectly as fresh debris in the middle entry just behind the second face. This paper presents a case history developed from the geotechnical measurements and on-site observations of this unique application of a yield-abutment gate road configuration and cable support system in the Hiawatha Seam.

Jan 1, 1996

By L. D. Tracy

Many bituminous coal-mining companies have inaugurated extensive safety programs, but the failure to have approved or permissible equipment or safe practice in only one part of a mine has resulted in disaster. The necessity of using only equipment bearing the U. S. Bureau of Mines approval plate is emphasized by the fact that many accidents are the direct result of carelessness on the part of trusted employees using non-permissible equipment. A concrete example is found in the case of an explosion on October 26, 1926, in a mine in the Pittsburgh district, Pennsylvania. Story of the Explosion At about 10 o'clock on the night of the explosion an examination was made in No. 2 butt left and parallel off No. 14 north, and was found to be clear of dangerous accumulations of gas. (See figure). Several hours later a crew of two men brought a self-propelling rock-dusting machine within 50 feet of the face of No. 2 butt parallel before they examined for gas. The machine operator found an accumulation of explosive gas about 13 inches from the roof. He began to wave his arms thoroughly mixing the gas and air. Undoubtedly a highly explosive mixture was created, and as the men attempted to run the machine back to fresh air as explosion occurred.

Jan 1, 1927

By G. S. Scott

In the course of the investigation into the causes, behavior, and control of mine fires, which the Bureau of Mines is now conducting, some attention was given to the subject of spontaneous heating. It is self-evident that the temperature of a pile of broken coal will rice if the rate of generation of heat exceeds the rate of brat dissipation and will fall if the opposite is the case. Factors that affect the rate of generation of heat are:

Jan 1, 1941

By N. Wang, A. I. A. Salama

"An index to evaluate the amenability for processing of different coals is implemented. The index is based on the well-known Mayer-curve or M-curve. The index is superior to other existing indices and is implemented using Microsoft-Excel™. Several coals are used to demonstrate the implementation of the index proposed.IntroductionIn 1950, Mayer introduced a curve that carries the information embedded in the fir s t three curves or ash curves of the conventional washability tables and curves (Peng et al., 1979; Osborne, 1988). The curve was labeled the Mcurve (abbreviation for Mittlewertkurve in German or the Mayer- curve). The main idea behind the curve is to use the ordinate for the cumulative mass and the abscissa for the ash (attribute) mass. Specific slopes on the resulting curve represent the cumulative float, cumulative sink, and elementary ash (attribute) contents (Mayer, 1950, 1953, 1957; Venkatesan, 1975; Osborne, 1988; Salama, 1989). Beyond the ash values, the curve carries graphical information that can be used in evaluating coal processing characteristics. Consequently, it becomes possible to present several raw coals on a single diagram, thus making it easier to compare their processing characteristics. This is particularly useful in comparing various size ranges of raw coal or the same size range from different seams. Therefore, the M-curve is adopted as a vehicle for developing the “processing (washing) characteristics index” implemented in this paper."

Jan 1, 2001

By P. Sarnoff

Gold has always been a crisis investment. For centuries gold has been considered globally the money of last resort. In time of war, inflation, financial uncertainty, political upheaval there has with few exceptions always been a flight to gold. The gold paradox simply is that even though we have gone through for the past handful of years all the kinds of. anxieties that would cause the gold price to rise, it has instead dropped drastically. Figure 1. illustrates the important factors that influenced the gold price significantly up or down before 1987. Obviously, since then, even though we have had wars, inflation, financial problems involving breaking banks and thrifts let alone collapsing financial institutions, the gold price has both in the long-term and the short-term trended downwards. Figure 2. depicts the gold price path since 1987. If the presence of time-honored and time-tested factors that should have driven the gold price up didn't do the job, then logic dictates that new factors to drive the gold price down and keep it depressed arose. And they did. But before addressing these depressants permit me to turn to the arcane art of gold price prediction and fore-casting.

Jan 1, 1992

By W. M. Peirce

COAL'S importance in the metallurgy of zinc may be gauged by the fact that approximately a million and a half tons is so employed annually in the United States. This brief paper will show in what way the various steps in the treatment of zinc ores utilize this fuel, either in its primary form or as coke or gas, and to what extent. The first step in zinc metallurgy that requires the use of fuel is roasting the sulphide ore, which is the type of ore in which zinc commonly occurs. Since the roasting is nearly or completely autogenous, however, this use of fuel is too minor to warrant further attention. Concentration of zinc ores is usually carried out by conventional milling methods, but a pyrometallurgical method, the Waelz process, is used to concentrate certain low-grade ores, and to recover the zinc content of certain residues in concentrate form. The Waelz process uses a continuous rotary kiln in which a mixture of coal and zinc-bearing material is heated to a

Jan 1, 1948

By J. O. Claassen

"A study conducted at 22 operating mines in the southern African region indicated that each mine employs about five management and improvement methods with roots in the manufacturing industry. All respondents reported the implementation of cost-saving initiatives, whereas 80% of the mines are affected by restructuring. TQM, Six Sigma, BPM, and TOC were found to be the most prevalent manufacturing management and improvement methods used. A mechanistic vs systemic evaluation of the suitability of these methods to bring about positive change in the industry suggested that complex, ever-changing mining systems are better served by a systemic flow-based approach, which is embedded in methods such as TOC, JIT, TPS, and Lean Production. These methods, however, lack industry presence, possibly because they do not effectively deal with the unique challenges associated with the mining environment. It is argued that successful mining business management and improvement depends on management’s ability to deal effectively with mining industry-specific requirements, the integration of the geologymining- plant system, and the implementation of systemic flow-based principles in all aspects of mining. IntroductionThe study aims to explore the use of manufacturing management and improvement methodologies in the southern African mining industry. Considering the unique challenges associated with mining operations, attention is given to the applicability of the most commonly used manufacturing methodologies in the tactical, operational, and strategic environments. The article endeavours to stimulate more research and debate in an unexplored field of study."

Jan 1, 2016

By David K. Hylbert

This study investigated roof falls in room-and-pillar drift coal mines in eastern Kentucky and utilized geologic methods for predicting roof conditions in advance of mining. In the Highsplint mine, the roof was classified in four categories or conditions: Condition A and B (Laminated Shale), Condition C (Rolling Sandstone with Shale in Pockets) and Condition D (Zone of Major Sandstone Roll(s)). Structure contour and isopach maps of the Darby coal bed and associated immediate roof rocks were used to project axial trends of the sandstone roof. Trend mapping in the mine and on outcrop provided more detailed control for roof projections.

Jan 1, 1978

By J. T. Ryan

FIGURES for the first 11 months of 1935 indicate that the total coal production of the United States for 1935 will be approximately 416,000,000 tons, or almost identical with the production figures for 1934. Bituminous production will show a gain of about six million tons, and anthracite production a loss of about the same tonnage, compared with the previous year. This does not take into account so-called "bootleg" anthracite coal amounting to approximately 5,000,000 tons. Twenty-nine years ago, in 1906, the production of coal was almost identical with this year's production. At that time, 626,000 men were employed in producing this tonnage, which took a toll of 2138 lives from accidents. In 1935, approximately 540,000 men were required to produce the same tonnage with an estimated loss of 1155 lives. This shows definite safety advancement in the industry, but even so accidents are still costing an average of 3c. a ton more than they should.

Jan 1, 1936

By Sugie Prawono

Jacked pile is the only piling system in which the load capacity of the pile, at any penetration depth, could be monitored directly during its installation process. Each installed pile could have a graph of jacking load versus depth of penetration. For safety purposes, the maximum applied jacking load during installation of a pile could be assumed as the minimum load capacity of the pile. This load capacity will increase with time since the drop in soil strength due to the installation process will recover later on. In order to determine accurately this jacking load, a research was carried out by comparing the load capacity of a pile at certain depths to the jacking load recorded during the installation process. The load capacity could be calculated using cone resistance, qc, and local friction, fs, from Dutch Cone Penetration Test. A graph could be drawn of the load capacity against the depth. By applying a correction factor, a, to the data of local friction, the calculated graph could be matched to the graph of recorded jacking load. The a factor is found to depend on the soil type, which is in this case, represented by the magnitude of cone resistance. The soil type is divided into 3 categories according to qc values (qc < 500 Kpa; 500 Kpa < qc < 2000 Kpa and qc > 2000 Kpa). Graphs of the a factor versus depth and a sample of calculation are presented in this paper for easy application.

Jan 1, 1999