Search Documents

The Golden Cross Mine will be the first underground gold mine in New Zealand to operate since 1952. The development plans, along with the conditions and circumstances presently found in the now ongoing mine development, will be discussed as well as a brief review of planned stoping activity and stoping results to date.

Jan 1, 1991

By Sushil Bhandari, S. S. Rathore

Controlled drilling and blasting continue to be an important method of block production and for block splitting. Drill and blast technique has disadvantage that sometimes, it produces cracks in uncontrolled manner and also produces micro cracks in the block as well as in remaining rock, if not carefully carried out. Recovery by this method is low compared to other methods. Therefore, attempts have continued to develop controlled growth of crack in desired direction. In this paper a series of tests are described using detonating fuse in marble. Economics of different methods is also compared. In comparison to conventional use when holes are lined with inexpensive cardboard or plastic liners with a slit, the cost and damage is the least and development of crack is in desired direction.

Jan 1, 2002

By Carl Pinches

Underground or surface mining is only the first stage in the ore mining process. Once the ore is mined, it is transported to the surface for further processing. Generally, this is done to extract the particular metal or other component of the ore that has commercial value in its purified form. In its raw state, there are typically between 4 and 7 g/t (0.12 and 0.2 oz/st) of valuable material from rock mined. Once on the surface, the ore is crushed and milled in order to obtain smaller rock particles and to expose the minerals that contain the desired metal or component. Mixing the milled ore with water, a process known as ?froth flotation,? can be employed. This technique consists of a series of tanks, or ?cells? through which the process liquid flows. To obtain the maximum recovery, the milling and flotation process will often be repeated a second time. An increase between 100 and 1,000 g/t (2.9 and 29 oz/st) of rock following this stage of the process is typical. Efficient recovery is key to maintaining a profitable mining operation. The measurement and control of the froth flotation process is vital.

Jan 1, 2010

New developments in the pipe conveyor and belt are advanced to address the growth in the capacity, length and complexity of pipe conveyor systems. Improved belt construction can offer better stability during horizontal curves and resistance to twist. Low rolling resistance rubber compound can significantly lower the power consumption and belt tension, producing capital and operation cost savings. Dynamic analysis, when used to analyze the conveyor?s starting and stopping behavior, can improve the design and reliability of long overland pipe conveyor systems. For these three aspects, technical backgrounds and field installations as examples are discussed in this paper.

Jan 1, 2012

By R. Boom, K. C. Mills, S. Riaz

This paper details the recent trends in slag-related research from 1999 to 2003. The trends in thefollowing are outlined: • Annual publication rate • Geographical origin of the work • Nature of the research (e.g. thermodynamics, kinetics) • Nature of the slag studied. This study has revealed that slag research in the USA and Europe has decreased to about a half over the last 20 years and that there has been a significant decrease in Japanese research in this area in recent years. However, these decreases have been offset by significant increases in Chinese and Korean research activity. There has been a significant increase in the amount of work carried out on the recycling and environmental aspects of slags in recent years.

Jan 1, 2004

By Roy C. Bartholomae, Jeffrey Shawn Peterson

1. INTRODUCTION In the early 1980s, the U.S. Department of the Interior’s Bureau of Mines Pittsburgh Research Center required that a large reverberation acoustic facility be constructed. This facility was designed to determine the sound power level emissions of mining equipment, especially continuous miners and jumbo drills. A contract for a conceptual design of a reverberation chamber was awarded to Wyle Laboratories of Huntsville, AL, which had extensive experience in the design, construction, and accreditation of acoustical reverberation chambers. The following standards were referenced as guidelines for the design of the chamber: ANSI S1.31-1980, “Precision Methods for the Determination of Sound Power Levels of Broadband Noise Sources in Reverberation Rooms” and ANSI S1.32-1980: “Precision Methods for the Determination of Sound Power Levels of Discrete-Frequency and Narrowband Noise Sources in Reverberation Rooms.” Specific requested criteria included that the room be large enough to accommodate typically large mining equipment and that there be adequate acoustical modal density in the frequency range of interest. It was also required that the room dimensions would support broadband acoustical measurements down to the 100 Hz third octave band. With the closing of the Bureau of Mines in 1996, this reverberation chamber lay dormant for a number of years. However, this facility is now part of the National Institute for Occupational Safety and Health’s (NIOSH’s) Pittsburgh Research Laboratory (PRL). One of NIOSH’s missions is to decrease noise induced hearing loss among the nation’s mineworkers. To this end, PRL researchers are refurbishing and instrumenting this reverberation chamber to facilitate assessment of the various engineering controls being developed to decrease the sound power level emissions of mining equipment. Early on, this work has sought to bring the chamber up to the level of ISO 3743-21 standard for engineering grade measurements for broad-band noise, with a longer range goal of improving the lab to meet the requirements of ISO 37412standard for broadband precision grade measurements. 2. DESIGN OF THE REVERBERATION CHAMBER The nominal room dimensions are 18.3 meters long by 10.3 meters wide with a height of 6.7 meters. The chamber volume is 1,286 cubic meters. These dimensions are important, as few reverberation facilities are large enough to test typically huge mining equipment. The floor is poured concrete with a sealer to make it acoustically reflective. The walls are built of hollow concrete block, 16 inches long x 8 inches high by 12inches thick. Each block has two hollow cores. The hollow block cores were completely filled with concrete with horizontal and vertical steel reinforcing bars 16 inches on center. This was done to supply a

By R. E. Whitehead

"Alkali/alumina and MgO/alumina molar ratio plots graphically portray both chemical and mineralogical changes accompanying potassic, phyllic, argillic, chloritic, and alunitic alteration of quartz monzonites and granodiorites hosting porphyry (as well as lode and greisen) ore deposits. The molar ratio plots can be used to identify different types of alteration. In most cases, the identification based on molar ratios coincides with petrographic data. In those instances where the molar ratio and petrographic identifications do not agree, the mineralogy might need to be re-examined. Hydrothermal alteration studies using trace elements could benefit from the application of complementary alkali/alumina molar ratio plots.Le diagramme des rapports molaires alkali/alumine et MgO/alumine illustre clairement les changements chimiques et minéralogiques qui accompagnent les altérations potassique, phyllique, argillique, chloritique, and alunitique des monzonites à quartz et des granodiorites encaissant les gîtes de type porphyrique, ainsi que des veines et des greisens qui leur sont associés. Les diagrammes de rapports molaires peuvent être utilisés pour identifier divers types d’altération. Dans la plupart des cas, l’identification basée sur les rapports molaires est en accord avec celle basée sur les données pétrographiques. Là ou il y a désaccord entre les rapports molaires et les données pétro-graphiques, il peut être nécessaire de réexaminer la minéralogie. Les études de l’altération hydro-thermale accompagnées d’une étude des éléments traces auraient avantage à utiliser un diagramme des rapports molaires alkali/alumine."

Jan 1, 2009

By G Siboni, A Correa De Araujo, M Gotelip Barbosa, M J. Venturini

In support of the development of its Liberian iron ore project, ArcelorMittal Mining Research and Development (AM Mining R&D) has performed characterisation and beneficiation test work on drill core samples received from the proposed mine area. In addition to this, a sinter feed product was composed by blending and processing the drill cores in order to predict sintering performance of the ore. This article presents the methodology used to prepare the drill core blend for characterisation, as well as describe the sinter pot trial. The results are presented, demonstrating how important this type of study is for the development of an iron ore deposit.CITATION:Gotelip Barbosa, M, Siboni, G, Venturini, M J and Correa de Araujo, A, 2017. The use of drill core blends to predict sintering performance, in Proceedings Iron Ore 2017, pp 297–302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the 'fine' and 'coarse' size classes appear to be diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours a different flotation environment. An improvement in the flotation kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferentially recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: > Standard flotation machines (standard energy input, rotor speed (r/min), rotor size/type) at the beginning of the row, where flotation is typically froth-phase limited and operational and set-up parameters have a limited influence on the recovery > Higher-powered flotation machines (high rotor speed, high-power rotor size/type) at the end of the row to improve fine particle recovery > Lower-powered flotation machines (low rotor speed, low power rotor size/type) to enhance coarse particle recovery. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for fine, and 'coarse' particles are predicted for both forced-air and naturally aspirated machines. The greater predominance of UG2 ore types, coupled with the skewed feed distribution of platinum group metals (PGMs) to the finer size fractions, suggests that PGM flotation circuits are not designed for optimal recovery across the size distribution. The application of the hybrid energy concept to PGM flotation offers a possible shift towards a more efficient flotation circuit solution through a managed distribution of energy.

Jan 1, 2013

By Luke Erickson

San Francisco Public Utilities Commission is planning to replace 5 miles of pipeline under San Francisco Bay. The tunnel will be constructed using an Earth Pressure Balance (EPB) TBM and will be the first TBM-driven tunnel under the Bay. The alignment passes under environmentally sensitive habitats, through interbedded layers of sands and clays, and through a buried bedrock ridge. This paper discusses the geotechnical characterization and anticipated tunneling conditions and presents the analysis of various construction methods that resulted in the selection of an EPB TBM. Considerations related to tunneling with an EPB TBM are described in detail, including ground conditioners, TBM cutterhead wear, muck control, and squeezing ground.

Jan 1, 2008

By Pierre Roy, Claude Gosselin, Maryam Sadeghi, Michel Bourassa, Christian Rochefort, Claude Bazin, Gautier Mahieu, François Lavoie, Marilène Renaud, David Cataford

"Spirals are gravity concentrators used for the concentration of iron oxide minerals from ores. This paper presents the mineral size recovery curves observed for spirals operating in two Canadian iron ore processing plants. The size recovery curves are presented for rougher, cleaner and re-cleaner spirals. The partition curves observed for the spirals are significantly different than those observed for typical gravity concentration devices such as hydrocyclones or hydraulic classifiers. The size recovery curves show the complex behaviour of the minerals as they flow down a spiral and are analysed with a view toward process modelling and simulation. Initial simulation results show that gains in the iron recovery can be achieved by increasing the recovery of coarse iron oxide particles in the rougher spirals.INTRODUCTION Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and different heavy minerals ores (Wills, 1992). The classification of the particles in spirals is based on the combination of gravity, centrifuge, drag, lift and Bagnold forces (Atasoy and Spottiswood, 1995; Burt, 1984; Bouchard, 2001). Several papers are dedicated to the analysis of the forces acting on the particles flowing down a spiral (Das and al., 2007; Sivamohan and Forssberg, 1985; Holland-Batt and Holtham, 1991; Holtham , 1992). Most of these papers aim at the development of a general model for the simulation of the classification of the particles for coal ore processing. Few papers deal with the operation of spirals for processing iron ores (Hyma and Meech, 1989; Srivastava, 2001; Dallaire et al., 1978) and fewer papers present results for spirals used as cleaners following a rougher stage. Since the classification in spiral classifiers is dependent on the particle size and specific gravity a partition or performance curve commonly applied to classifiers (Mai Manga et al., 2012) is used here to analyse spiral operation. Few papers were found to describe the operation of spirals in terms of partition curves (Atasoy and Spottiswood, 1995; Holland-Batt and Holtham, 1991; Richards et al., 2000). Most of the investigations presented the application of a model to simulate the position of coal particles of various sizes and specific gravities along the trough of a spiral (Kapur et al., 1996; Holland-Batt and Holtham, 1991). In addition most of the available literature on spirals deals with one stage of concentration by spirals (Dallaire et al., 1978; Das and al., 2007; Sivamohan and Forssberg, 1985) while industrial circuits usually consist of rougher and cleaner spirals."

Jan 1, 2014

By Tom Retka

This three volume final report summarizes the activities and conclusions of this contract. The objective of the contract was to develop noise control modifications on a retrofit basis, for auger miner coal-cutting systems. Manuals were prepared to assist mine shop personnel in retrofitting the auger miner with these noise controls. Final Report Volume I - Details all vibration and acoustical tests conducted in development of the noise controls. Final Report Volume II - Noise Control Modification Manual for the Jeffrey 100-L Auger Miner describes the various noise control modifications to the auger miner, along with fabrication procedures, cost and vendor information. Final Report Volume III - Noise Control Modification Manual for the Jeffrey 94-L Bridge Conveyor describes the various noise control modifications to the bridge conveyor, along with fabrication procedures, cost and vendor information.

Jan 1, 1978

By M. -O. Suk, S. -K. Jo, S. -C. Shim, J. T. Kim, S. -H. Kim, C. -W. Seo, J. -S. Kim

An equilibrium study was carried out at 1873 K to ascertain the effect of carbon in CaO-SiO2-Al2O3-MgO-MnO-FetO slag systems on their FetO and MnO activity coefficients, representing the slag?s thermodynamic potential for steel reoxidation. Both ?FetOand ?MnO showed not only a sharp increment, but also a simultaneous slow decrement by increasing carbon content in slag, suggesting opposite roles of the carbon according to its stable forms. XPS (X-ray photoelectron spectroscopy) was introduced to clarify the stable forms of carbon in slag. XPS results prove that carbon dissolves in slag as carbonate, and carbide ions under oxidizing and reducing atmospheres, respectively. It was concluded that carbonate ions increase ?FetOand ?MnO, and that carbide decreases them. This paper suggests an application method of the present results to actual ladle refining processes, in order to enhance steel cleanliness without decreasing (FetO + MnO) content in slag. Keywords: carbon, slag, activity coefficient, FetO, MnO, carbonate, carbide, XPS, reoxidation, cleanliness

Jan 1, 2004

Research on the Thermodynamics of Siderite Roast Decomposition and the Experiment of Magnetic Roasting-Separation

Sep 13, 2010

By David Harrison, Edward J. Walter, Meitra Ferek

Agreat tool in the prevention of blasting complaints and subsequent damage claims. In today’s highly competitive industry, we are always looking for ways to become more cost effective. This article investigates the importance of pre-blast surveys-not just for regulatory compliance, but as an overall long term cost cutting and public relations tool.

Jan 1, 1995

By L. Obert, D. E. Stephenson

The objectives of this investigation were to develop a laboratory procedure in which core discing could be produced under known (and variable) stress conditions, and to study the discing characteristics of several fypes of rock. Discing of rock cores refers to the formation of discs or wafers of relatively uniform thickness which fracture or rupture on surfaces approximately *Fracture is a type of failure in which there is a complete loss of cohesion and fresh surfaces are created. Rupture is a type of failure in which there Is only a partial loss of cohesion. normal to the axis to the core (see Fig. 1). Usually the surfaces of the discs are concave-convex with the concave side toward the collar of the hole. The surface of the fractured discs are like those created by a tension failure (or possibly a shear failure with virtually no normal compressive stress). This phenomenon has been observed by a number of investigators1-5 in the course of diamond drilling in underground mines, especially in areas suspected of being under high stress. The state of stress in the core required to produce discing is not exactly known. Tranter and craggs6 theoretically investigated the stress distribution in an infinite cylinder, subjected to hydrostatic pressure, minus p, from z = 0 to z = 8 and unloaded from z = 0 to z = 8, Fig. 2. The exact solution to this problem shows that a tensile stress develops in the loaded region near z = 0 with the greatest tensile stress on the axis of the cylinder. A tensile stress also developed on the surface of the cylinder at a point just outside of the loaded zone. Jaeger and Cook3 experimentally investigated the discing mechanism by biaxially loading cores in a pressure jacket sealed at the ends by O-rings. According to the Tranter and Craggs theory it would be expected that failure should occur at the pressure discontinuity at the O-rings. The experimental results showed that if the specimen was unjacketed it broke at random points within the pressurized zone and at a pressure somewhat greater than the tensile strength of the specimen, presumably due to the development of a

Jan 1, 1965

By N. Hmidi, T. Yalcin, M. Papadakis, B. Hilscher

Mill tailings, containing iron sulphides in particular, pose an environmental concern since they constitute a potential source of acid mine drainage which can damage vegetation, harm soil and living organisms, and contaminate groundwaters. Proper disposal of acid generating tailings is therefore an important issue that must be addressed and resolved in a satisfactory manner. Placer Dome Canada operates a 4000 t/d gold cyanidation facility at Musselwhite mine, in northwestern Ontario, where the mill tailings have been classified as acid generating. This study was conducted to explore the effectiveness of froth flotation in removing the sulphide minerals from these tailings and producing a low-sulphur, non-acid generating material that could serve as a capping material for previously deposited tailings. Laboratory semi-batch flotation tests were carried out in accordance with an experimental design procedure, and a computer simulation program was developed to facilitate the evaluation of flotation performance. In this investigation, pH, collector concentration, and airflow rate were considered as the relevant flotation variables, and their effects were examined both experimentally and by simulation. Results have demonstrated that flotation can successfully desulphurize the Musselwhite mine tailings and render them non-acid generating.

Jan 1, 2004

Geological information is essential for a diversity of public and other purposes, including land use planning, hazard mitigation, and the exploration and sustainable use of natural resources. This is especially important in New Zealand, where the complexity of the geology is due to its position on an active plate boundary - the ultimate cause of earthquakes, mountain building, subsidence and volcanic activity. The geological setting also controls the origin and distribution of New Zealand's varied mineral and energy resources. Providing information about the origin, quality and quantity of mineral resources has long been seen as a key function of national geological organisations such as the Institute of Geological and Nuclear Sciences. Such information is essential for wise land-use decisions under the Resource Management Act. One of the major goals of the Institute is to quickly and effectively disseminate research results to interested users. The most effective and internationally accepted method of presenting geological data is by means of geological maps, which show the distribution of rock types and structural features at the surface. Most countries have ongoing gelogical mapping programmes, and in recent years the need for up-to-date, reliable information has led to a trend to accelerate basic geological mapping (eg US National Geological Mapping Act 1992; Australian National Mapping Accord 1990; Plan 2000 in the UK). Over the last 25 years, the Institute of Geological and Nuclear Sciences and its predecessors (NZ Geological Survey and DSIR Geology and Geophysics) have concentrated on detailed mapping of priority areas selected on the basis of economic and scientific interest. This has included remapping of Nelson-West Coast and Coromandel, regions with high mineral potential, for which 1:63 360 or 1:50 000 maps have been prepared.

Jan 1, 1994

By James J. Graham

Uravan, Ambrosia Lake, Gas Hills and South Texas are all historic names in US uranium. These mining areas supplied the uranium that brought the United States into the nuclear age during the 1960s, and fueled the birth of nuclear energy for peaceful uses — a promise of nearly limitless, clean energy for the world’s future. That promise still exists today, but it is hard to hear over the rhetoric of environmental activists and politicians. Nuclear power offers dependable electricity with limited environmental impact at stable prices. Nuclear power releases no greenhouse gases or particulate matter into the atmosphere. High level nuclear waste (HLW), although long lived, is readily controlled and compact. In the United States, generating 1 billion kWh of electricity with coal produces 47 kt (52,000 st) of solid waste (ash and sludge), compared to 3.6 t (4 st) of HLW produced by nuclear.

Jan 1, 2002

By Robert Benedetti

This paper describes various mitigation methods in order to reduce the maximum acceleration of the floorboard of hulled vehicles when explosive charges buried in water saturated sand were detonated beneath them. The effects on floorboard acceleration of adding a vehicle hull, several types of floorboard bracing, the use of foam to fill the gap between the floorboard and hull, and the use of foam to isolate the floorboard from the hull have been investigated. Small scale testing was conducted, which used bar magnet velocity gages to measure the velocity as a function of time of the center of the floorboard, directly over the charge, where the acceleration was expected to be greatest.

Jan 1, 2012