Search Documents

By Q. J. Browne, M. A. Miller

Silver Bell produces about 22,000T of fine copper annually from low-grade chalcocite and oxidized copper ore that is recovered by sulfuric acid leaching and SX-EW processing. The current mineable reserves are 146 million short tons averaging 0.39% Cu, at a 0.15% cutoff. Silver Bell utilizes two types of mining methods to develop the low-grade reserves: (1) a conventional blast, load and haul method for run-of-mine leach ore, and (2) rubblization of material on the margins of existing pits. Rubble leach ore is blasted, terraced with a bulldozer, and leached in place. Mining and/or rubble leaching is currently active in four separate pits. Laramide-age intrusive rocks host porphyry copper mineralization at Silver Bell. Quartz monzonite porphyry dikes and stocks, mafic-poor equigranular granite (alaskite), and sub-volcanic dacite porphyry are the predominant host rocks. Most of the ore currently mined comes from near-horizontal enrichment zones containing veinlets and disseminated grains of pyrite and chalcopyrite rimmed by chalcocite. Conversion from a milling operation to a leach only operation allowed for a much lower cutoff grade than was historically used at Silver Bell. Mine geologists were able to increase copper resources by drilling exploration targets that were previously interpreted to provide lower-grade mineralization below cutoff-grade for milling. Geologic parameters that effect the distribution of rubble and mineable leach ore include: ore grade and thickness, variable alteration styles in intrusive host rocks that affect fragmentation during blasting, acid consuming carbonate wallrocks (reactive skarn) which influence leach solution pH, solution flow paths and drainage, presence of leachable oxide mineralization in non-reactive skarn, and depth to hypogene mineralization which is currently uneconomic. Geologic parameters are used to predict rubble bench limits, vary blast hole spacing for consistent fragmentation, and correct errors in mineral zone classification based solely on blast hole assays. An expansion-drilling program has identified approximately 150 million tons of new leachable copper resources with an average grade of 0.35% Cu.

Jan 1, 2002

By D N. B Skinner, R L. Brathwaite, M S. Rattenbury

The Institute of Geological and Nuclear Sciences is undertaking a mineral resource assessment study of the Coromandel region, due for completion in July 2000. A key part of the study is the assembly of a geographic information system (GIS), a computerised tool for layering, analysing and presenting spatial information. The GIS is being assembled with ArcInfo/ArcView software and to date includes layers for a digital terrain model, an aeromagnetic map (open file mining company data), a geological map (from the QMAP project), areas of hydrothermal alteration, locations of mineral deposits (GERM database), stream sediment geochemical analyses (REGCHEM database), and a lineament map derived from satellite remote sensing data.

Jan 1, 1999

By Marco A. Vera

"This paper investigates the froth function in flotation and the associated upgrading process. Flotation literature has revealed that one of the main functions of the froth phase is the cleaning of bubble-particle aggregates by rejection of entrained material. The cleaning and transport processes across the froth phase exert straining forces on these aggregates on their way up to the froth surface. These forces will impact on the recovery of bubble-particle aggregates.The grade at the top of the froth (TOF) is a parameter related to the quality of particles collected by bubbles in the pulp zone (true flotation). It has recently been demonstrated that TOF corresponds to the maximum practically attainable grade described by the recovery-grade (or enrichment ratio) curve. TOF lumps all the processes experienced by the bubble-particle aggregates before reaching the launder concentrate. This paper describes a methodology for quantifying flotation performance by means of the top of the froth sample - a touch of froth.INTRODUCTIONFroth flotation may be the most important mineral processing technique, but its theory is complex and is not completely understood even though many aspects have been studied and reviewed (Teague, 1998; Wills, 1992).Two distinct particulate systems prevail in the flotation process: a pulp phase and a froth phase (Figure 1). The pulp zone had been studied extensively; however, it is only recently that techniques to measure the froth zone performance have been developed (Contini et al., 1988; Falutsu and Dobby, 1992; Feteris et al., 1987; Seaman, 2002; Vera et al., 1999b).Flotation involves a number of mass transfer processes, occurring in the pulp phase and the froth phase. The formation of the froth and its subsequent removal are considered to be two important steps of the process. Phenomena that occur in the froth phase are known to affect flotation performance significantly (Cutting et al., 1981).Because the froth has a high free surface energy (as a result of the extensive interfacial surface between liquid and air), it appears thermodynamically unstable. The foaming is a dynamic balance, as new bubbles are added continuously from the pulp, while others disappear from the top. Under steady-state conditions, the volumes of added and subtracted air are equal (Booth, 1953)."

Jan 1, 2003

By Y. He

The nature of the density distribution in a gas-solid phase fluidized bed for dry coal separation is an important factor in influencing the performance. However, during coal processing, fine slime would mix with dense medium of magnetite powder and accumulate in the bed, and its influence will affect the density of the bed. The mathematical model of the density distribution with fine slime behaviour was studied in an experimental laboratory system. The functional relationship between the density of the air dense medium fluidized bed and the coal slime content were fitted, applying the principle of least-squares method with damping factors. With the model, by analysing the trial testing data, the mechanism of the density distribution of the bed was studied and applied to a coal separation test with a pilot scale separator. Keywords: dry coal separation, gas-solid phase, model fitting.

Jan 1, 2002

By Alessandro Bertero, Dylan Pearson, Wesley Schmutzler, Matteo Bertoni

"The SR 83/US 331 highway is located in the Florida panhandle, where it connects the Walton County beaches to the I-10 corridor. The roadway is of vital importance to the economy of the area as well as its safety since it represents the primary hurricane evacuation route from southern Walton County. The Florida Department of Transportation (FDOT) decided to increase the number of traffic lanes from two to four and improve the geotechnical properties of the moderately deep, very loose foundation soils, that had affected the highway rideability for years. The soil mixing was selected as the method to meet the unique deep ground improvement challenges of the project. The design required that Shallow Mixing Method (SMM) be used to build a 10-foot thick platform that transferred axial load to the bottom soil layers through a series of Deep Mixing Method (DMM) columns. Upon completion over 8,300 SMM columns and 1,500 DMM columns had been installed, with no remedial work required. Also, only 1% of the almost 1,500 specimens tested did not meet the specification requirements. This paper will describe the challenges encountered and provide valuable information that may be useful for other future projects, including details not previously published.INTRODUCTIONThe counties of Walton and Okaloosa have been a very popular vacation destination for many ears. The 50-mile long coastline boasts beautiful, sugar-white beaches and waters the color of emeralds. The popularity of the area has been growing even further, over the last few years. A consequence of this phenomenon is a fast-paced increase of the traffic flow on the SR83/US331 highway, especially at the bridge that connects the Walton County beaches across Choctawhatchee Bay (Fig. 1) to the heavily traveled I-10 corridor. The highway plays a very important role for the area also as a commercial link and as the primary hurricane evacuation route from southern Walton County. The increase in traffic has produced higher travel time, when not a complete traffic paralysis, and exacerbated the issue of ground settlement where accelerated wearing of road foundation occurred due to the presence of very loose, moderately deep, soils, that had afflicted the highway for several years. The Florida Department of Transportation (FDOT) decided to put an end to these issues by increasing the number of traffic lanes from two to four and improving the geotechnical properties of the foundation soils. The Design-Build Maximum Price Request for Proposal (RFP) issued for the expansion of the Choctawhatchee Bay Bridge saw the participation of numerous D/B teams which produced various technical solutions. Among them, the FDOT selected the Skanska/Parsons Brinckerhoff (General Contractor) proposal which provided for the use of soil mixing as the ground improvement technology. The design/build team assigned Foundation & Geotechnical Engineering (Designer of Record) the ground improvement design which Treviicos South (Specialty Contractor) would execute."

Jan 1, 2017

By N. W. Kirshenbaum

"The Marconaflo slurry system was originally developed to reduce costs and solve technical problems in the marine transport of mineral cargoes. In the short time since its inception, it has been found to offer economies and advantages for land-based and in-plant materials handling. This efficient method of reclaiming and slurrying particulate materials at very high pulp densities can be directly utilized in a wide variety of mineral process systems. These include: storage-reclaim applications, where even cohesive, compacted materials can be reclaimed from settled storage ""on demand""; the growing number of hydrometallurgical operations wherein slurried materials are processed to extract or yield metals; certain applications associated with pyrometallurgical treatment; and as a means of augmenting the performance of conventional mineral dressing equipment, such as thickeners.INTRODUCTIONIn the continuing effort to lower costs of producing minerals and extracting metals, the field of handling and transportation often receives too little attention from those engaged in the mining and winning of ores and metals. This comment, which pertains to ferrous and non-ferrous as well as to non-metallic producers, is especially pertinent to products having relatively low value, where transport costs can be a major portion of the delivered selling price to the minerals receiver.One method which was developed recently for the purpose of reducing costs and solving technical problems in marine transport and handling of mineral cargoes is the MARCONAFLO slurry system. A notable feature of this system is its versatility; in addition to its use in marine transport1*, some of its diverse applications have included the mining and reclaiming of tailings2 and in-plant materials handling3. As the concept and fundamentals of this system have been well explained previously4,5, the mechanics of the system will not be elaborated upon here. Rather some specific ways in which MARCONAFLO can be applied to processing and extraction will be explored."

Jan 1, 1973

By Ira Sohn

This article revisits global projections made in 1981of eight metallic and fertilizer minerals for the year 2000. The objectives here are to quantify the differences between the projected and observed levels of consumption for the year 2000 for eight of the 26 nonfuel minerals covered in the earlier study. An attempt is then made to attribute these (often) large differences to the major determinants of minerals demand — income, technological, regulatory and other policy changes, and changes in the recycling rates of the metallic minerals. The eight minerals covered are aluminum, copper, iron, mercury, nickel, phosphate rock, potash and tin. This summary article presents the actual population, gross domestic product (GDP) and per capita GDP changes from 1970 to 2000, compared with the projected rates for these important determinants of mineral use, along with the observed growth rates of minerals consumption for the eight nonfuel minerals included in this study. When the projections are compared with the observed global consumption levels for the year 2000, the differences range from +43 percent for nickel to +229 percent for potash.

Jan 1, 2005

By W. J. Witte, M. K. Witte

"The purpose of this report is to present a generalized preliminary design and cost estimates for a typical heap leach operation such as might be undertaken in Northern Ontario. This report should be of value to anyone in the mining industry planning, or contemplating, a heap leaching operation in Ontario, either on a large or small scale. While more detailed costing and design work will obviously be required for each specific project being contemplated, the data provided in this report should enable parties to make preliminary estimates of the costs of proposed projects and should identify most of the planning and design parameters that will need to be considered.Although heap leaching has been used extensively as a low cost gold recovery method in other parts of the world for many years, it has only recently become of interest to the Canadian mining industry.In order to investigate and demonstrate the feasibility of using heap leaching in Ontario, the Ontario Ministry of Natural Resources in 1982, undertook to locate a private sector proponent willing to undertake a 10,000 ton demonstration project. This project was to have been carried out at a production scale under normal northern Ontario field conditions. The Ministry was to have provided technical management and design for the designated project."

Jan 1, 1985

Application of Natural Zeolite for the Removal of Diethylenetriamine (DETA) and DETA-Metal Complexes from Flotation Process Water

Sep 13, 2010

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation. MFIRE was written in Fortran 77 and compiled with Microway1 Fortran for the Intel 80386 based computers with a 80387 math co-processor. The source code is portable and available for users who wish to modify the source code to operate on other computers. This user manual describes the development of MFIRE, the input format and requirements, the output, common errors, fire parameters, and examples MFIRE application. Valuable reference material is included in the appendices. Knowledgeable users may skip directly to the PROGRAM INSTALLATION AND OPERATION section to begin using MFIRE immediately.

Jan 1, 1995

By AJ Rorke, JD Botes

Presplit blasting in strip mines is aimed at creating a safer wall to work under during the coaling operations. Good quality presplits are also necessary for effective throw blasting and drainage of the blast block. A less obvious but important function is full coal recovery. Optimum Colliery has been experiencing rock freezing against the presplit highwalls. The rock formed in patches along the highwall and trapped coal beneath it. The material that was &ozen comprised the rock between the back row of holes and the presplit and was often up to 3 m thick (the stand off distance between the back line and the presplit). The cozen rock formed predominantly along the bottom halfor bottom two thirds of the highwall. Along the top portion of the highwall, the presplit crack was usually well formed with visible barrels. This problem, or similar variations of it, is common on many South African strip-mine operations. Investigative work was carried out at Optimum Colliery to correct the problem. This paper presents the information and measurements that were made and discusses the solutions that have been applied to solve the problem. It was found that there were two independent causes for the tiozen material, with each contributing more or less to the frozen rock along the highwall. It was found that the presplit was not forming properly in places, especially closer to the bottom of the highwalls. The reasons and the solutions are presented. The second cause was found to be associated with reduced detonation velocity in the back line holes coupled with low confinement from long delay periods. Emulsion explosive that is sensitised with air bubbles was found to be prone to this phenomenon near the back of high-energy blasts. A change in the explosive formulation in the back-line holes, together with reduced delays in the back line, has resulted in significant improvements. The details are presented in this paper.

Jan 1, 2000

By Fathi Abdrabbo

Open caissons are used for many geotechnical engineering applications. Open caissons may be used as deep foundation elements bypassing weak soils to tip in firm deeper strata, and in rivers and maritime construction to reduce the risk of scour. Open caissons are also used for collecting sewage water through gravity sewer pipe networks or from sewer force mains. In such applications, the design and construction of open caissons require a detailed soil investigation program. In this way, the design and construction plan of an open caisson can be developed with full knowledge of the prevailing subsoil conditions. The engineering and construction techniques are key factors to achieve functional caissons. Based on close observations during construction stages, the current study presents some challenges that were encountered during the construction of two open caissons of internal diameters 20 m and 10 m (65.6 ft and 32.8 ft). This paper describes the procedure followed to alleviate the construction difficulties encountered. Site exploration program and control measures required to satisfy design and construction requirements are crucial aspects. Sinking of open caissons in dense or very dense sands is risky. Incorrect sinking of open caissons may cause extra cost, delay in construction, and harm to nearby structures. Air/water jetting near the cutting edge of an open caisson, outside slurry trench, and/or inside open trench may be used to drive an open caisson downward. Unsymmetrical work around an open caisson may lead to tilting of the caisson. If this occurs, the tilt should be immediately corrected before resuming the sinking process. Improper cleaning of fine materials on the caisson?s excavation bed, and/or inappropriate pouring of underwater concrete may result in a defective concrete seal. The paper contains a series of practical guidelines to assist those intending to use open caissons, and shares good caisson sinking practice with practitioners. Finally, the study aims to understand the difficulties encountered and to anticipate future problems.

Jan 1, 2012

By Norman A. Jull

"Factors which affect the separation achieved in a hydrocyclone are discussed and illustrated with graphs of some mathematical relationships.Definitions of separation and sharpness include comment on use of elutriation devices.A plea is made for better evaluation of field data prior to their reporting or use in calculations. Methods of evaluation are suggested, with samples of the relevant calculations.An example of the effect of percent solids errors is given, with computer printout and plotted corrected recoveries.INTRODUCTIONThe range of interest in cyclones runs from a simple demand for classification results to a detailed study of published equations defining cyclone characteristics. Probably this group covers as broad a range and, in an attempt to offer something for everyone, I will begin with general operating comments, then move on to more analytical topics. Ideally, an author would compose his paper after the discussion period, when he would have a better idea of the areas of special interest to his audience.Sor'1e of you may share our incurable fascination with classification, especially as performed in cyclones. It is amazing that such a simple device could be in use for more than 20 years and retain as much mystery as it does. Substantial parts of the mystery have been solved but some remains, to keep up our curiosity. There is at least one valid reason: the unusual compactness of this device, which makes internal observation very difficult. What other unit can you think of which performs such a complex separation between particle sizes, shapes and specific gravities at such high capacity? Retention time in a cyclone is typically 3 seconds!Mutual Agreement - In a cyclone, every parameter of geometry and of operation interacts with every other. In an orderly discussion of individual parameters it would be necessary to repeat, in every section, 11 if all other factors are equal"". Could we agree now, for our mutual convenience, that that phrase is clearly understood between us during the remainder of this paper?"

Jan 1, 1972

By Karla Kaboth, Brad Garraway

"The surface of many concentrate thickeners has traditionally looked like that of a flotation cell. Over the last three years Normandy Golden Grove Concentrator, in partnership with Outokumpu Technology have developed and implemented an innovative breakthrough deaeration technology to address this problem.When installed in the thickener feedline, the system successfully detached air bubbles adhering to the solid particles and removed air bubbles from the feed stream, subsequently presenting a fully deaerated feed to the thickener feedwell.Tests to date have shown an 80% reduction in overflow solids. As a result, costs associated with concentrate loss and measures to recover concentrate that settles in process tanks and ponds have been minimized.MOTIVATIONIt is recognised in mineral processing operations that the entrainment of finely divided air in thickener feeds can cause significant problems in the operation of a thickener. This is particularly the case with thickening of flotation concentrates, in which air bubbles are strongly attached to the mineral particles and are difficult to remove. Such particles attached to fine air bubbles rise to the thickener surface, and hence over the weir and into the thickener overflow. High solids carryover can lead to a direct loss of mineral product, and if the product settles in process water tanks and ponds, the recovery of this product by means of intermittent dredging operations is usually expensive and inconvenient.Many concentrate thickeners are fitted with devices which attempt to alleviate this problem. Froth rings or baffles, skimmers and froth sprays, all play a part in reducing the amount of solids carried over into the overflow. However, many froths are very stable and persist despite these measures. In the worst cases, a thick froth layer forms which builds up to a depth greater than the froth ring, and hence may overflow or pass beneath the ring . Any concentrate that finds its way past the froth ring can also cause blockage of the overflow weir and launder, and has the potential to upset clarification performance by cutting off sections of the overflow handling system. The formation of a froth layer on the thickener also makes it more difficult for the operator to monitor the clarification performance."

Jan 1, 2001

By R. J. Fruehan

Slags have many useful functions in iron and steel making. In particular, slags are used to remove impurities such as sulphur, phosphorus and inclusions from the metal, and a large amount of research has been done in this area. Slags also insulate the metal thermally and form reactions with the atmosphere such as reoxidation and nitrogen pick-up. However, slags serve other more unique functions, several of which are reviewed in this paper. The role of slags in new iron smelting processes with regards to reduction of ore and gaseous desulphurization are discussed. In iron smelting processes, much of the reduction occurs by the reaction of carbon in the char and the metal suspended in the slag with iron oxide dissolved in slags. The slags also react with the gas resulting in sulphur removal from the process. The mechanisms of these reactions and pilot plant data for these processes are given in this paper. Slag formation within ferrous burden materials affects the cohesive zone and the performance of the blast furnace. Recent theoretical and experimental findings on this topic are presented. In the electric arc furnace, foamed slags are used to allow for higher power operation and productivity. Of particular interest, foaming in stainless steel production is more difficult than for normal steels. The foam index, or the ability of the slag to foam, for stainless steelmaking is similar to that for carbon steelmaking slags. The poor foaming is due to the lack of gas generation for the foam. Methods to increase foaming in stainless steelmaking are discussed.

Jan 1, 2004

Analysis of rock discontinuities, collected using a scanline method, has been undertaken at the Iron Duke open cut mine, on the southern margin of the Middleback Range in the Gawler Craton, South Australia. The iron mineralisation, which is a product of supergene enrichment of carbonate sediments, is located on the W (western) limb of a gently N plunging D2 macrosyncline. Mesofolds plunge shallowly to the NE or steeply to SE, suggesting two shortening events, of which the second produced significant macrofolds. Discontinuities include:faults and shears which display variable orientations, mainly striking WNW dipping steeply N; mesofractures or joints maintaining a well constrained orientation, dipping steeply S, subvertical striking E-W; and bedding surfaces which are folded about a gently N plunging axis. Through this example of the regional control exerted on local discontinuities, it is clear that discontinuities are not randomly distributed as often assumed in purely statistical approaches. Commonly for rocks of any age there is a distinct discontinuity pattern, reflecting the geological deformation history. If the controls exerted on local rock discontinuities can be determined and assigned a number related to their significance, the way forward is available to develop a site specifc knowledge base that can make realistic predictions for any position in a given rock mass. Such a procedure would involve assessment of the regional geology, linked to scanned discontinuities either via manual or automatic means. Recent advances in automatic scanning rock faces (eg by the I-SiTE Laser Radar) to determine discontinuities distributions, enable the rapid calculation of rock characteristics. This is a significant advance in rock engineering, providing a method of safe and quick collection of data. However it creates problems in the presence of an increase in the geotechnical data available, which should be assessed in the context of the regional geology. Although techniques are underway to analyse post-blast discontinuities, the next signifant potential advance in this area could be the integration of a knowledge based system to assess discontinuities ahead of mining, incorporating regional assessment and human intuition.

Jan 1, 2000

By Dennis R. Dolinar

Screen material in the form of welded wire mesh and geogrids are used in underground coal mines to prevent the fall of small pieces of rock from the roof between roof bolts. Further, if the screen is installed during the production cycle, roof fall injuries can be reduced significantly. Therefore, the National Institute for Occupational Safety and Health (NIOSH), because of the safety implications, conducted an evaluation of screen materials commonly used in U.S. coal mines to determine their support characteristics and identify the parameters that could affect their performance with respect to controlling the fall of rock from the roof surface. To evaluate the load and stiffness characteristics of the screen, a test frame was designed and installed in the Mine Roof Simulator (MRS) at the NIOSH Pittsburgh Research Laboratory (PRL). With this test set up, the screen is bolted at four corners of the frame and a center load is applied. The test set up allows for up to 20 in of screen deflection while the load and screen defection are continuously recorded. A series of tests were conducted to evaluate the effects of various parameters such as bolt tension, the type of load bearing surface and the size of bearing plates on welded screen performance. The most common screen material used in U. S. coal mines is an 8-gauge wire welded in a 4-by-4-in spacing or aperture. The peak screen load was normally limited by wire breakage. The conditions at the bearing plate influence the nature of the wire breakage. However, the screen stiffness was controlled by slippage at the bearing plates, and by weld and wire failure. The size of the bearing plate had a significant effect on the performance of the welded screen. Therefore, the design capacity of the 8-gauge screen is evaluated based on plate size. For a 6-by-6-in bearing plate the average peak load is 2,900 lb with a stiffness of 250 lb/in. For an 8-by-8-in bearing plate, the average peak load is 4,500 lb with a stiffness of 430 lb/in. These test results are based on a 4-by-4-ft bolt spacing. A geogrid mesh was also tested.

Jan 1, 2006

By Ed Coulter

Nevada has a population of 1.2 million people of which only 21% or 312,rIXl are native born Nevadans. he population between 1980-1990 grew a record of 389%. and ls the fastest growing state in the union. While only 2.5% of the total population are direct employees of the mining industry, excluding Reno and Las Vegas, one out of every three people living in Nevada work for a mining related industry.

Jan 1, 1991

By John G. Peacey, Leoncio Sevilla G., Ford. Kevan J. R., Erling Villalobos C.

"Kinross Gold Corporation’s Mantos de Oro (MDO) gold/silver mine in northern Chile currently processes 15,000 tpd of oxide ores through a mill, whole ore cyanide leach plant followed by a Merrill-Crowe refinery. With the expected depletion of these oxide ores in a few years a new sulphide mineral deposit, Ladera-Farellón has been identified to potentially replace existing ore reserves. The deposit contains approximately 0.5g/t Au, 6g/t Ag and 0.5% Cu. The principal sulphide mineral in the deposit is enargite (Cu3AsS4) which hosts the majority of gold and silver and the copper. Direct cyanidation testwork has shown the sulphide mineral is refractory with a low gold recovery of 36% and silver recovery of 45%. Oxidation of the sulphides is required to liberate gold and silver and allow recovery of copper as an important pay-metal. Therefore, at MDO a new metallurgical process route with oxidation as a pretreatment step is required for viable treatment of such new sulphide mineralized material with acceptable recoveries of pay-metals.Analysis of flowsheet options was completed based on bench-scale and pilot scale metallurgical testwork as well as with reference to existing studies and operations. The process options investigated assume concentration of sulphides by flotation, followed by either pressure oxidation, bacteriological oxidation or roasting. Preliminary evaluation of flowsheet options focused on process risk, operability, technology availability and the economics of the project with emphasis on use of the existing metallurgical plant to reduce capital cost. Operating costs for each process option were also included in the relative analysis.The challenges of treatment of MDO sulphides, principally enargite and pyrite for recovery of gold, silver and copper center on fixation of arsenic and sulphur capture with environmentally acceptable disposal of residue tailings. This environmental focus was included in the process option selection and comparative analysis.This paper presents a review of the process options considered and highlights comparative advantages/disadvantages of each process with associated environmental issues. Preliminary conclusions are drawn on roasting as a potentially favorable process option for the treatment of MDO sulphides."

Jan 1, 2009

By Shane McDonald

Australia produces approximately 84 million tonnes of coal per annum from 30 longwalls in New South Wales and Queensland, operating at an average depth of around 300m. Industry trends and expectations place increasing emphasis on the reliability of these operations; for example, the current average face width is 245m and this is expected to increase to approximately 270m by 2010. In recent years, Beltana No.1 Mine has consistently been Australia?s highest longwall producer, with ROM output of 7.2Mt in YEJ2007. Strata management has become a key feature of the operation of Australia?s longwall mines, as a tool to manage variances in the geotechnical environment. This involves an understanding of the impacts of the geotechnical environment on ground behaviour and the implications for mine design, stability and associated support, interaction and horizon selection. The anticipated ground control impacts of these factors form the assumptions that drive the format of plans specifying both triggers and actions, with quantified, monitoring-focussed experience used to refine the plan in a continuous improvement (ie ?plan-do-check-act?) process. This paper summarises the Beltana No.1 Mine strata management methodology and experience to-date.

Jan 1, 2008