Search Documents

By Walter W. Fisher

A study of copper cementation on iron was initiated to determine the effect that deposited copper has upon subsequent cementation. A microscopic investigation of cementation on an iron surface showed that cupric ion precipitates predominately on a growing copper deposit attached to the iron surface. A kinetic study of the cementation process in a revolving drum showed that the cementation rate is enhanced by the copper deposit attached to the iron surface and by the discrete copper particles of a cement copper slurry. The kinetic study also indicated that the character of the deposit is affected by the major anion in the solution. The cementation process is visualized to occur as a series of electrochemical cells in which cupric ion precipitates on copper dendrites attached to the iron surface.

Jan 1, 1973

Analysis of Procedures and Drivers for Industrial Waste Management

Sep 13, 2010

The Mineralogical Researches of Gold Ores and Technological Products at Operating Factory in Olympiada Mine (Russia)

Sep 13, 2010

By John C. LaScola

The Bureau of Mines investigated coal storage silos to determine how gassy coal must be for methane accumulations in a silo to become hazardous and where such accumulations are likely to occur. Methane concentrations were measured in the open space above the stored coal pile, in the pile, and in the reclaiming area. No methane layering was found in closed-top silos. Reclaiming areas were as gassy as the top part of the silos. Coal samples were collected from the conveyors entering the silos in order to assess the gassiness of the coal. No simple correlation was found between the gassiness of the coal stored and the measured methane concentrations. However, at mines where the average 24-hour gas emission from the conveyor belt samples was 14 ft3/ton or more, fans or open tops were used. It appears that a large fraction of the methane released during storage remains in the void space between the coal particles.

Jan 1, 1980

By Roy L. Wilfong

The thermal decomposition of the ammonium sulfate, carbonate, nitrate, oxalate, and sulfate salts of praseodymium, neodymium, and samarium was investigated thermogravimetrically in the temperature range 25° to 1,500° C. Each salt was decomposed at a heating rate of 2.5° C, per minute. The pyrolytic sequences have been identified and the temperatures of formation of inter-mediates, the minimum oxide formation temperatures, and values for loss on ignition have been determined. The nonstoichiometric ranges between Pr6011 and Pr203 and the extent of these ranges have been determined for oxides derived from the carbonate, nitrate, and oxalate salts of praseodymium. The alum and sulfate salts of praseodymium produced the sesquioxide without forming the intermediate non-stoichiometric oxides. The temperature limits of formation and regions of stability for the alums and sulfates were better defined than were those for the carbonates, nitrates, and oxalates. The minimum oxide formation temperature increased in the order of samarium, neodymium, and praseodymium irrespective of the anion.

Jan 1, 1962

By Andrew B. Cecala

The Bureau of Mines conducted a brief laboratory study on the 10-mm diam Dorr-Oliver nylon cyclone to investigate (1) whether high wind speed (>300 ft/min), or sampler inlet orientation with respect to wind direction, can introduce errors when sampling respirable dust, and (2) whether any such errors can be reduced by using an inlet shield. Being preliminary in nature, the study was not structured to produce definitive results, but rather to discern likely trends and to indicate whether or not a more in-depth study of the problem is warranted. Photometric mass sensing measurements suggested that as the wind velocity increased, the cyclone sampling directly into the high-velocity airstream tended to oversample, relative to the cyclone sampling in a low-velocity airstream. Orientation of the sampler introduced measurable differences in sampling efficiency at higher wind velocities. A shield placed around the cyclone diminished the effects of wind velocity and sampler orientation on sampler performance. Results of this work offer sufficient evidence to substantiate the need for a more in-depth study.

Jan 1, 1983

By L. P. James, W. W. Atkinson

Utah has produced about one billion troy oz. (31.7M tonnes) of silver, more than any U.S. state except Idaho. Several very high grade ore systems, now closed, occur within large polymetallic limestone-hosted districts related to plutonic complexes. These Utah mines fed several major lead smelters for nearly a century. Interaction of magmatic chloride-rich fluids with carbonate rocks localized significant bonanzas within these districts. A low sulfidation state was produced in the fluids by their passage through limestones. The Bingham porphyry mine has also yielded more byproduct silver than other porphyry copper-gold systems. Away from exposed intrusive rocks, some large silver-only systems occur in Mesozoic sandstone and in caldera-related veins in volcano sedimentary rocks. Thick permeable latest-Proterozoic basement meta quartzite sequences present beneath western Utah may have been important, as perhaps they were in the Coeur d’Alene district of Idaho, in providing chloride and silver-rich ore fluids. However, it is clear that specific Tertiary magmatic events played an essential role in the evolution of the Utah silver-rich metallogenic province. The largest silver districts in the state are genetically related to porphyritic plutonic rocks.

Jan 1, 2000

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability o mine safety management personnel to apply analytical techniques to Injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the application of the quantitative procedures to mine-specific accident/injury experience data is discussed in detail in the form of case studies. The accident data from three mines are analyzed, and recommendations for training are proposed for each of the mines on the basis of this analysis. The procedures to apply cost-benefit analyses are described along with the cost benefit ratios for the training program/policies for the mines.

Jan 1, 1993

By P. H. Morris

To achieve the full potential of sub-aerial co-disposal the properties of the co-disposed wastes must be known and understood. A description is given of the morphology and properties of waste deposits that were formed during 19 field trials of sub-aerial co-disposal at the dual Goonyella-Riverside mine in Queensland and at Hunter Valley No.1 and Warkworth mines in New South Wales

Jun 19, 1905

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1982 (October 1, 1980 -September 30, 1981) under its Minerals Health and Safety Technology program. Contingencies may require that a significant port ion of the program be deferred into fiscal year 1983. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the systems technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1981

By Jamie Bonner, Ray Hutton, Taro Nonaka

The Nancy Creek Tunnel is a deep tunnel, designed to store and convey wastewater by diverting flows from trunk sewers currently at or near capacity in the northwest of the City of Atlanta. The tunnel, constructed in hard rock, has an overall length of 13,300 m (43,700 ft), and a finished diameter of 4.9 m (16 ft). The project is currently under construction by a joint venture of Obayashi/CJB for the City’s Department of Watershed Management. This paper describes the contractor’s techniques and equipment, as well as discussing challenges which were overcome. The project is scheduled to be complete in October 2005.

Jan 1, 2005

By Frank S. Wartman

"The experimental flotation work described in this paper was undertaken to test the conclusions derived from a previous microscopic and chemical study of several samples of converter slag. That study3 resulted in the conclusion that approximately 90 per cent of the copper content of a converter slag wad in either the sulphide or metallic form, and that if the slag were cooled slowly the copper-bearing material would be in particles of such size that they would be freed from silicate and magnetite grains by grinding the slag to pass a 150-mesh sieve. If this were true, it should be possible to separate the copper-bearing grains from slowly cooled, converter slag by the flotation process.Many attempts, of which the author has seen no published account, have been made to treat slags, especially converter slags, by flotation. In every case these trials have been made with chilled slags, in which, as shown in the preceding report, the copper-bearing material is top finely disseminated, to be freed by any reasonable degree of grinding.The flotation tests described in this paper have shown that it is possible to recover by flotation about 30 per cent of the copper content of a converter slag containing 3 per cent copper and to obtain flotation concentrates which have a copper content of 35 per cent.Acknowledgment is made to G. L. Oldright, supervising engineer of the section of nonferrous metallurgy, U. S. Bureau of Mines, for valuable assistance and direction; to W. A. Sloan for chemical analyses; and to Alfred P. Towne for assistance in experimental manipulation."

Apr 1, 1931

By Fred S. Karn

Inhibitors are used in coal mines as a precaution against accidental dust explosions. Although rock dust is the usual inhibitor many others have been tested. To facilitate testing a screening process using laser irradiation was proposed. The procedure includes irradiation of a coal-dust mixture followed by mass-spectrometric analysis of the evolved gases and an evaluation of the flammability characteristics of the gases. Carbonate-type inhibitors decreased the percentage of combustibles in the gases generated and inhibitors like NaCI (thermally stable salts) decreased the total gas generated. A suitable test procedure did not result from the investigation, demonstrating the inadequacy of fast heating, non-combustive techniques in rating inhibitors of coal dust explosions.

Jan 1, 1973

By T. C. Alex, S Srikanth, Premchand

It has been suggested that reduction of the iron and manganese phases as far as FeO and MnO is preferred for the complete liberation and selective reduction of the copper, nickel and cobalt oxides in manganese nodules. The oxygen partial pressure/temperature regime suitable for this purpose has been delineated. Free-energy minimisation and thermogravimetric results indicate that the requisite conditions can be achieved if more than 10% of neutral oil is used at temperatures greater than 923 degrees C. Neutral oil content, temperature and roasting time have been optimised to maximise leaching recoveries of Cu, Ni and Co: up to 96% of Cu and Ni and up to 85% of Co can be recovered if 15% of neutral oil is used as a reductant at 973 K for 90 min

Jun 21, 1905

By H. P. Rue

The Bureau of Mines has recently collected two samples of crude oil from wells in the Greasewood Flat area of northeastern Colorado. Sample 31310 was taken from the Continental Oil Co.'s well Briggs No. 1 which care in or September 27, 1931, with a maximum production of 940 barrels per day. Sample 31311 was taken from tie Reiter-Foster Oil Co. Is well Ida Johnson No. 1 which came in on August 24, 1931 with a maximum production of approximately 1000 barrels per day.

Jan 1, 1932

By Loren R. Anderson

A probabilistic slope stability computer model was developed at Utah State University and independently evaluated by CH2M Hill Consulting Engineers as a design and analysis tool. Volume I of this report describes the model and Volumes III and IV are users manuals for the computer programs. This volume (Volume II) constitutes the report by the CH2M Hill. It includes a description of a field investigation and stability analysis of an existing tailings dam. Based on the results of the analysis, the tailings dam was evaluated for redesign using probabilistic considerations. Conclusions are made regarding the usefulness of the model as a design tool.

Jan 1, 1982

By Dale Matthews

The Getchell Mine, near Winnemucca, NR, was discovered in the 1930s and was initially mined to recover gold from oxide ores. During the 1940s and 1950s, gold was recovered from the highly refractory arsenic sulfide ores using horizontal kilns to roast the ores. During the 1960s, fluid bed roasters were used to oxidize the ore and recover the gold. The mine was shut down from 1968 through 1985. In 1985, heap leaching was started on the low-grade oxide ores that were available. In 1989, a pressure oxidation circuit was started to recover gold from the higher grade sulfide ores. Flowsheet The basic plant flowsheet of the Getchell Mine are shown in Figs. 1 and 2. The plant was designed to process a nominal 2.7 kt/d (3000 stpd) of ore with about an 85% onstream availability and a gold production of 15.5 kg/d (500 oz/ day). Run-of-mine (ROM) ore is fed directly to a wet semiautogenuous grinding (SAG) mill after the +457-µm (+18in.) rock is removed on a stationary grizzly. From the SAG mill, the ore goes to a ball mill where it is ground to 80% -75 µm (-200 mesh) and is then sent to a thickener. The SAG and ball mill operate in closed circuit using cyclones.

Jan 1, 1994

By Natesa I. Jayaraman

A field study was conducted by the Bureau of Mines to determine the feasibility and effectiveness of a secondary ventilation system retrofitted onto an Eickhoff EDW 340L double-drum shearer as a technique for controlling respirable dust generated during a longwall mining operation. An airflow duct was formed by enclosing the bottom of the undercarriage with steel plate and cutting air channels through the ends of the undercarriage frame. Air intakes were provided behind each cutting drum and at several locations along the undercarriage. Grills were installed at the intakes to prevent the broken coal from entering the ducting. A dust collector consisting of 5,000-ft3/min fan, water sprays, and a minicyclone panel was installed on the shearer at the tailgate end. Field results indicated that the secondary ventilation system reduced respirable dust more than 60% along the face. Reduction was less near the intake airway and when secondary dust sources occurred.

Jan 1, 1977

By W. Sondermann

"AbstractThe construction of a distribution centre of minerals for a global mining and resources cooperation demanded the control of deformations and displacement of the stack reclaimer facilities on very inhomogeneous subsoil conditions. The variation of quality from soft clay with CPT values below 1 MPa up to rock formations were the challenge in design and execution of all the foundation works.The advanced design considerations were resulting in a barrier wall system to limit the deformations of the up to 40 m deep bored pile of the stacker-reclaimers, whereas the layout of the barrier wall and the stiffness of the elements had a major impact on the residual lateral forces to be absorbed by the bearing structure.IntroductionA large international raw material distribution organisation is currently building an iron ore and pellet distribution centre on the north-western coast of Malaysia. The distribution centre will handle around 90 MTPA (million tons per annum) of iron ore and includes accompanying plants for loading and unloading iron ore and pellets, pelletizing plants as well as corresponding storage space for these raw materials. The total storage space extends about 800m north to south respectively 1400m east to west and is about 200m from the coastline. The project area is located in a wide valley basin, bounded by a range of hills to the north. The existence of soil with low bearing capability in the area designated for the plant meant that measurements for ground improvement were required in the storage areas, in order to combine the needs of iron ore and pellet storage areas with requirements of the loading facilities as the overall project demand.Project LayoutThe iron ore distribution centre and the pelletizing facility both consist of an import/export jetty, material handling facilities, pellet plant and the associated infrastructure. This publication describes the execution of ground improvement and foundation works for the loading and storage system, which consists of five rows of stockpiles and four intermediate rows of stacker-reclaimers. The total area of these systems comprises 278,881 m2 (Fig. 1)."

Jan 1, 2014

By J. I. Paige

The Bureau of Mines studied methods for recovering unreacted titanium minerals and petroleum coke from titanium chlorination plant wastes prior to neutralization treatment with lime. The objective was to recover valuable raw materials and to reduce the amount of waste materials that must be treated for disposal. Samples of solid wastes were physically beneficiated by gravity concentration (tabling) to recover titanium minerals containing 69.0 to 92.4 wt-pct Ti02 and by selective carbon flotation to recover petroleum coke containing 94.0 to 96.8 wt-pct C. Laboratory data indicate that the recovered titanium mineral would decrease the amount of solid waste to be disposed of from 32.8 to 53.9 wt-pct. The recovery of coke would further decrease the amount by additional 32.9 wt-pct. Preliminary tests conducted on recovering vanadium, chromium, and columbium from liquors obtained by leaching chlorination residues also have shown that (1) 97 pct of the vanadium was extracted from leach liquors in a two-stage solvent ex-traction procedure and (2) 58 pct of the columbium and 40 pct of the chromium were separated from the leach liquors by an ion exchange technique using a strong acid resin.

Jan 1, 1982