Search Documents

By Lukasz Maciag, Ryszard Andrzej Kotlinski, Ryszard Krzysztof Borówka, Dominik Zawadzki

Concentration and composition of rare earth elements (REE) and major elements in the sediment samples from the IOM H11 Fe-Mn nodule deposit, eastern part of the Clarion-Clipperton nodule field (located between the Clarion-Clipperton Fracture Zone - CCFZ; tropical Pacific), have been studied. We show the controls on REE concentrations and described vertical/horizontal variability of selected metals in pelagic sediments from the CCFZ. According to Kato et al. (2011), who analyzed 2000 seafloor sediment samples at 78 sites of the Pacific Ocean, deep-sea mud shows high concentrations (2230 ppm maximum) of ?REY and could be potential resource of these elements in the future. However, our work does not fully confirm that sediments in the IOM H11 are significantly enriched in REE.

Sep 1, 2014

By Meliton M. Garcia

The volume of gases produced in major and trace amounts following the detonation of two water gel and two emulsion explosives in a mine were determined. The volume .of the major gases (CO, CO2, NO, and NO2) was measured immediately following detonation, during the mucking operation, and following the removal of the muck. Tests to identify and quantify the gases produced in trace amounts were performed following the detonation only. The volume of each major gas per pound of explosive (ft /lb) ;ranged as follows: CO, 0.0424-0.3231; CO , 0.6819-1.5632; NO, 0.0129-0.1320; and NO2, 0.0019-0.1111.. An approximate average of 95% of the gases produced was found in the test chamber immediately following the detonation, while less that 2% was found in the chamber following removal of the muck. Benzene was the most significant compound found to occur in trace amounts. Scaling tests performed with a water gel and an emulsion explosive suggest that the volume of the gases per unit mass of explosive detonated diminishes as the amount of explosive per blast increases.

Jan 1, 1986

By Greg Sheppard, Eduardo Nebot

Australian researchers have developed new technologies aimed at improving safety and productivity at openpit mines. A data acquisition and feedback system for electric rope shovels has been shown to substantially reduce cycle times and decrease excessive machine duty caused by stalls. This data acquisition system was developed by the Cooperative Research Center for Mining Technology and Equipment (CMTE). It has been tested on a P&H 4100A shovel at Coal & Allied’s Hunter Valley operations and a P&H 4100XPB at BHP Billiton Mitsubishi Alliance’s Goonyella Riverside Mine in Central Queensland. In addition, CMTE member P&H Mine Pro Services has used the technology to acquire field data from a P&H 4100XPBrope shovel at RAG’s Belle Ayr Mine in Wyoming’s Powder River Basin.

Jan 1, 2002

By William H. Pomroy

The Bureau of Mines, through a 4-year program of combined in-house and contract research, has developed the necessary hardware and software technology to provide rugged, reliable automatic fire protection for surface mining mobile equipment. One element of this program was a continuing effort to help foster rapid mining industry acceptance of the technology by keeping end user costs reasonable. This report is an analysis of the economic impact of surface mining mobile equipment fires and the cost benefit of utilizing automatic fire protection systems to abate these losses.

Jan 1, 1982

By Franklin D. Cooper

The value of nonfuel raw mineral production in the United States for 1977 increased over that of 1976 by 5%, from $16.7 billion to $17.5 billion. Metals declined by 5% from $6.1 billion to $5.8 billion, chiefly because of strikes in the iron ore industry and a depressed copper market. Subsidization of mining industries in some foreign countries accounted in part for the excess of copper and some other metals on world markets. Weak metal markets and continued slowdowns in the world economy were the main reasons of the virtual absence of new mine projects. Increasing domestic governmental involvement affecting mineral industry activities, such as pricing controls, public land withdrawals, and the Surface Mining Control and Reclamation Act, effective August 3, continued to be controversial and to be criticized by various segments of the industry.

Jan 1, 1980

Two new inorganic-organic hybrid polymers, Al(OH)3-polyacrylamide (Al(OH)3-PAM) and Mg(OH)2-polyacrylamide (Mg(OH)2-PAM) were synthesized and successfully applied for the treatment of oil sand tailings. The results indicate that both Mg(OH)2-PAM and Al(OH)3-PAM were unaffected by the change in pH, and could be applied to oil sand tailings with varying sand-to-fine ratio (SFR). The optimum dosages for the Mg(OH)2-PAM and Al(OH)3-PAM were about 330 g/ton and 650 g/ton, respectively for SFR 3.75. The flocculated oil sand tailings dewater quickly producing 66-68% solids. The flocculated tailings produced similar filtration rate before and after shear. Mg(OH)2-PAM treated oil sand tailings produced twice the filtration rates (220 ml/min) compared with Al(OH)3-PAM. This study clearly indicates that Mg(OH)2-PAM and Al(OH)3-PAM is a viable solution while decreasing the mass-production of tailings and increasing the rate of water-recycle.

Jan 1, 2012

By Liang Sha

In this study, adsorption of copper by chemically modified orange peel was investigated. A conspicuous change occurs in the surface morphology of the biomass due to modification, which is depicted by SEM images. Equilibrium isotherms and kinetics were obtained and the effects of various factors, including solution pH, contact time, initial metal ions concentration and temperature, were studied by batch experiments. Kinetics was found to be best-fit pseudosecond- order equations. Equilibrium was better described by Langermuir isotherms rather than Freudlich isotherms. At 25?, pH5.30, the maximum adsorption capacity was 70.67mg?g-1 . With increase of temperature, adsorption efficiency decreased. The biosorbent was suitable for repeated use for more than five cycles.

Jan 1, 2009

By Tom Pfitzer, Alice Correa, Meredith Hardwick

The past decade has brought significant changes in the use of risk-based criteria for safety within the U.S. Department of Defense. The Range Commanders Council (RCC) chartered a working group to develop and define risk acceptance criteria for protecting the general public and mission essential personnel from debris from launch ranges. This working group has continued to develop and update RCC Standard 321 as the needs of the ranges and range users have evolved. A revision to RCC Standard 321 is near finalization and will include casualty criteria, guidelines for assessing risks due to other flight hazards in addition to inert debris, and an overall risk management process for range safety. This paper reports on work in progress and includes several precedents which may prove important to the explosives safety community.

Jan 1, 2007

By Etienne Audibert

No satisfactory theory has yet been advanced to explain what takes place when an explosive is fired in a mixture of firedamp and air. The only means of measuring the danger is to fire the explosive into the gas mixture and note the effect, but the conditions of firing must be chosen carefully. This report is presented in the hope that it will assist in determining what method to use. The experiments have been designed to show the effect of the principal factors involved in the conditions of firing, and the results give information that seems to have some value.

Jan 1, 1940

By S. A. Sayed, M. N. M. Ahmed, M. A. Doheim

The performance of a 12.7 cm hydrocyclone was investigated by considering the effect of design variables (diameters of the vortex finder and apex) and operating variables (pressure drop and solids content of the feed) at a medium feed solids concentration of mixed minerals. Cut-size was found to be the most important parameter in hydrocyclone design and operation. The effect of feed pressure in reducing hydrocyclone cut-size is less pronounced at medium feed solids concentration with a mixed mineral feed. The choice of vortex finder diameter and apex diameter becomes more sensitive at medium feed solids concentrations. The effect of feed solids concentration in increasing the cut-size becomes less marked at higher concentrations. Predictions of an empirical model were found to be in good agreement with experimental data. Comparison of results obtained from the model with those predicted by theoretically derived models showed the latter to be more promising, with the turbulent two-phase model giving closer agreement with the experimental data

Apr 1, 1995

By Thomas J. Peters

Tungsten, silver, lead, zinc, and placer gold occur in the Cucamonga B RARE II area (no. B5174). A strata-bound, scheelite-bearing zone at the Blue Diamond prospect (fig. 1, no. 1) contains an estimated 16,000 tons (15,000 t) of identified, subeconomic resources averaging 0.16 percent tungsten trioxide (W03). There is a high potential for discovering additional tungsten resources at this property. The California-Hercules prospect (fig. 1, no. 5) ha; a mineral occurrence which contains an estimated 1,000 tons (900 t) of tactite averaging 1.3 oz silver per ton (45 g/t), 0.75 percent lead, and 0.72 percent zinc. Another occurrence, at the Blew Jordam Prospect (fig. 1, no. 4) has an estimated 100 tons (90 t) of tactite averaging 10 oz silver per ton (340 ,/t), 3.75 percent zinc, and 2.3 percent lead. There is a moderate potential for discovering silver, lead, and zinc resources at these prospects, which are in metamorphic pendants. There are a few lode gold prospects in the area (fig. 1, nos. 3, 11, 14) are on geologic structures which parallel the San Andreas Fault, northeast of the area. These deposits are not well exposed and have been historically unproductive. Placer gold in area B occurs locally in the beds of intermittent tributaries to Lytle Creek (fig. 1, nos. 10, 12, 13) in concentrations as high as $1.17 per cu yd ($1.53/cu m, at a gold price of $450 per troy oz). The deposits have no significant volume, but could be utilized for recreational panning and suction dredging. In the Cucamonga C RARE II area (No. C5174) placer gold occurrences locally contain as much as $1.23 per cu yd ($1.61/cu m). However, gravel containing the gold appears to be limited to stream beds, and does not occur in sufficient quantity to constitute resources. Recreational panning and dredging also may occur in this area.

Jan 1, 1983

By M. Faraji

Inclusions formed in a high-carbon, manganese-silicon killed plain steel (Fe-0.77C wt%) were studied. Various techniques were used to characterise the inclusions, and the latter were classified according to their chemical composition, size and morphology. The main constituent elements entering the inclusions were Mn, S, Al, and oxygen. Alongside MnS and some Al2O3 inclusions many non-metallic inclusions appeared in complex forms, consisting of silicates, sulphides and oxides. Duplex oxy-sulphides, mainly MnS combined with Al2O3, or SiO2 were the most common complex multiphase inclusions in this steel. The nanoindentation technique was used to assess and rate different types of inclusions and data of the hardness and elastic modulus of individual inclusions at room temperature are presented.

Jan 1, 2010

By Siavoljub D. Maksimovic

The Bureau of Mines, through a cooperative agreement with Duquesne Light Co. of Pennsylvania, field tested a method of using pneumatic stowing of crushed limestone to construct seals in long-abandoned mine openings that were part of an active mine closed shortly before sealing. A total of 13 openings at 11 sites were backfilled. In pneumatic stowing, material is conveyed through a pipeline and into the mine opening under low air pressure. The stowing equipment consists of a power sup-ply, a blower, a feeder to inject material into the pipeline, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. The fill material used was well-graded limestone aggregate up to 1-1/2 inches in diameter, with sufficient fines. This fill was modified at five locations by the addition of portland cement, expansive cement, and/or bentonite. The pneumatic stowing method is safer and faster than conventional methods, is cost competitive, and eliminates or reduces the exposure of workers to possible hazards since the nozzle can be kept outside the mine opening. The equipment is mobile, but some modifications in the technique would improve performance. The technique was used at remote locations where other methods could not be used without disturbing the environment.

Jan 1, 1982

By AMIRA P588 Research Team

This contribution summarises new knowledge and data, obtained during a three year ARCAMIRA funded research project, on the mineralogical and geochemical characteristics of hydrothermal alteration associated with low sulfidation, gold-silver epithermal deposits. These data are used to develop exploration vectors for use at both deposit and district scales, plus techniques have been established to distinguish ore grade epithermal systems from barren or low grade systems. Deposits investigated were Ladolam, Papua New Guinea, Gosowong and Mt Muro, Indonesia, Cerro Vaguardia, Argentina and Bimurra and Twin Hills, Australia.

Jan 1, 2005

By Etienne Audibert

No satisfactory theory has yet been advanced to explain what takes place when an explosive is fired in a mixture of firedamp and air. The only means of measuring the' danger is to fire the explosive into the gas mixture and note the effect, but the conditions of firing must be chosen carefully. This report is presented in the hope that it will assist in determining what method to use. The experiments have been designed to show the effect of the principal factors involved in the conditions of firing, and the results give information that seems to have some value.

Jan 1, 1940

By Joel Nonnweiler, Rafael Castro, Ross Webb

The three thousand foot long 66-inch diameter Folsom East Interceptor Section2B was completed accident free, on time and under budget with no measurable surface settlement. The tunnel passed through nested cobbles, highly abrasive sands and gravels, and abandoned mine workings with less than five-feet of cover at times. Preventing settlement was critical since the tunnel passed under a heavily traveled state highway. A pilot project to test microtunneling and pipejacking methods in the same ground conditions abandoned both drives before completing the planned drive lengths. This paper discusses performance of the conventional tunneling method selected to excavate the ground and the effectiveness of the ground modification techniques employed.

Jan 1, 2001

By P. G. Pigott

The lack of technical information regarding the physical characteristics of kaolins and bauxitic kaolins, rejected during the mining of bauxite near Eufaula, Ala., has retarded their commercial utilization. This investigation was undertaken to determine their behavior when used in refractories. Ores were evaluated as refractory raw materials by compounding dry-press mixtures and specialties following procedures common to the industry. Products now on the market were used for comparison in laboratory evaluation.

Jan 1, 1959

By Swapan Bhattacharya

United States federal and state regulatory authorities require underground mine operators to adopt adequate measures to minimize material damage to the surface caused by nine subsidence. This paper presents an approach to define and determine the extent of material damage due to subsidence from underground coal mining. The basic steps involved in the development of adequate criteria have been enumerated together with the approaches and methodologies used.

Jan 1, 1984

By M. John Brodie

This report reviews the regulatory environment as it pertains to waste rock management and disposal from mining operations, excluding coal and placer gold operations, in the \irate of Alaska. It is based on the EPA's staff position on an effective program to regulate mining waste as presented in the May, 1990 Strawman II document. The unique conditions which occur in pans of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a waste rock facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection, are examined.

Jan 1, 1992

By J. Stacho, Frankovská. J.

"Abstract The use of continuous flight auger (CFA) piles in Slovakia has increased significantly in recent decades. High-rise building of administrative centre Lakeside Park in Bratislava is based on piled-raft foundation. The technology of CFA has been used due to the advantages of this technology in comparison with driven and bored piles in local geotechnical conditions. Piles have been designed in accordance with Eurocode 7. Resistance of piles was calculated by using an analytical calculation model for bored piles according to Slovak technical standard and CFA technology has been taken into account by coefficient equal to 1.1. Settlement of piles was calculated by using a calculation model which is being used in Czech Republic and Slovakia. Two well instrumented static load tests were carried out to verify the pile design. The results of static load tests showed that the design was conservative. The paper presents analysis of numerical modelling of CFA pile and static load tests. Load-settlement curves and load distribution curves over pile shafts are compared. Software Plaxis 2011 has been used for numerical modelling. Hardening soil model allows considering over consolidation of Tertiary Silts and water pressure in deep sandy lenses. The article also presents the parametric study where the influences of pile-soil interface reduction factor, over consolidation ratio and material models of soils are analysed. The results of numerical modelling showed that the most appropriate results have been obtained when the interface reduction factor equal 0.9 and real behaviour of groundwater were considered. The conclusion of the paper confirms that mechanical behaviour of the ground can be better understood and determined by using FEM than analytical methods.1. IntroductionPiles are among the most frequently used elements of deep foundations. Piles transfer loads down to a suitable bearing stratum when the soil immediately below a construction is unsuitable. Piles are also used to reduce settlement of structure. At present, the requirements of limit settlement of structures are more stringent. Examples of these structures are commercial and administrative centres that form a complex of different tall buildings. High-rise buildings cause greater contact stresses than connected low-rise buildings. Pile foundations in such cases should be placed under the high-rise buildings to achieve an appropriate settlement.Resistance of piles can be determined from static load test results, in-situ tests and empirical experiences or calculations. Static load tests give the most reliable results, but these tests are also the most expensive. This is the reason for constant development of computational methods. Especially numerical methods give more accurate results by using more sophisticated material models e. g. hardening soil or hypoplastic model."

Jan 1, 2014