Search Documents

By G. Hausen, H. Micka

"Modern signal and power electronics made adjustable-speed AC drives technically feasible and reliable and economically attractive. Cycloconverters are discussed as a proven technology for mine hoists. \IntroductionUntil rather recent technical and commercial advances in power and signal electronics, DC motors were used almost exclusively for applications requiring continuously adjustable operating speeds and torques. More recently, the significantly higher efficiency and the accordingly lower operating costs of AC motors gained importance. An effective and efficient speed control of AC motors requires the control of AC voltage and frequency. Table 1 shows typical applications of adjustable-speed AC drives.CycloconvertersOf particular interest to the mining industry are cycloconverters for hoist drives. The cycloconverter represents by far the simplest, most efficient and most economical means of converting a constant-voltage, constant-frequency supply into an adjustable-voltage, adjustable-frequency supply as required for the speed control of AC drives operating in the frequency range to half of the utility frequency.Cycloconverters feeding synchronous motors or induction motors are ideally suited for slow-speed direct-coupled drives."

Jan 1, 1988

By J. E. Sepulveda, R. Morrow

"In full scale mineral grinding operations, the steel balls normally utilized as auxiliary grinding media get to be consumed at different specific rates, as determined by 3 basic mechanisms: abrasion/corrosion (wear), impact ball breakage and impact surface spalling, the latter relating to the removal of rather small pieces of steel coming off the exposed surface of the balls due to repetitive impact with other balls in the charge or the surrounding mill liners. In conventional ball milling applications, the clearly predominant mechanism is gradual wear by abrasion/corrosion. In the case of SAG mills, where the make-up balls may be as large as 6”f diameter, breakage and spalling mechanisms are significant contributors to total ball consumption, although not to the extent of overriding wear mechanisms.Ball wear has been well characterized by the Linear Wear Theory, as presented at the last CMP 2014. Impact breakage has been customarily monitored, at the ball manufacturing site, via Drop Ball Tests (DBT) consisting of repeatedly dropping balls from a standard height and accounting for the number of broken balls and the weight loss (spalling) of the remaining unbroken balls. When properly conducted, DBT’s should provide meaningful indications of the breakage and spalling resistance of large diameter balls. The current publication is focused on the interpretation and projection of DBT results to full industrial scale, taking into account all 3 mechanisms of grinding media consumption in SAG mills.INTRODUCTIONA thorough, quantitative understanding of the independent contribution of all active grinding media consumption mechanisms is of the highest practical relevance, particularly in semiautogenous (SAG) milling operations where ball breakage and spalling can not be ignored or neglected, as it has been normally acceptable for conventional ball milling processes. The high severity impact conditions currently imposed in typical SAG mill environments create serious challenges to the manufacturers and suppliers of large diameter (5”–6”) SAG balls, whose products must be capable of surviving such harsh operational conditions with minimum breakage or spalling."

Jan 1, 2015

By D. E. Poole

Injury Prevention: Dependent, Independent and Interdependent In recent years, management-directed (dependent)safety programs have lost ground to the more successful self-directed (independent) programs, where employees take responsibility for their own safety. Today, with the growth of the team concept in industry, a mutual-caring (interdependent) approach to workplace safety is gaining wide acceptance. This presentation compares characteristics and results of the three progressive levels of safety responsibility and explains how to develop a successful interdependent program. The presentation will also detail the common principals that are necessary for safety excellence under any of the management styles.

Jan 1, 2000

By Paul D. Tomlingson

Part two of this two-part series covers the use of an integrated information system with administrative information, including error and absentee reports as well as open work files. Part one (ME, July, page 650) discussed conceptualizing and developing a maintenance information system. It explained what information is needed to manage such a system.

Jan 8, 1985

By Earl Redman

The Juneau Gold Belt portion of the Juneau Mining District has historically had the greatest mining and exploration activity within the district. Between 1880 and 1983, the mines within the Juneau Gold Belt produced 6.7 MM oz gold, 3.1 MM oz silver, and 45 MM lbs lead, which had a total value of about $157,000,000 at the time of production. This report summarizes Bureau of Mines work completed in 1986, the second year of the Juneau Mining District study. Fifty mines, prospects, and occurrences were examined and 638 samples were collected for analysis during 1986. Metallurgical samples were collected from seven deposits and preliminary tests of cyanide amenability have been completed for five of these. The simultaneous discovery by private industry and the Bureau of gold-bearing quartz veins cutting diorite gneiss recently exposed by the retreat of the Herbert Glacier is the most notable result of work during 1986. This location yielded gold values up to 7 oz/st.

Jan 1, 2011

By L. T. Isaacs, W. H. Traves

A numerical model for analysing the drainage of fill in mine stopes has been described. The model can be used to analyse the process of fill drainage in existing and proposed mine stopes. The validity and potential value of the model have been established by experience with a simpler, 2-dimensional numerical model and by testing the new model against the earlier model. The new model is more useful than the 2-dimensional model because it allows for heterogeneity of fill material within the stope - a factor that has been demonstrated to affect drainage characteristics significantly. The 3-dimensional model is also capable of predicting pore pressures and drainage rates at specific locations in the stope without the need to resort to 2-dimensional generalisations. Such information, integrated with relevant field data as they become available, will provide valuable mine planning information for the scheduling of filling operations and design of fill mixes

May 1, 1991

By Scales PJ, Ralston J

Fine coal particles have been examined with respect to dustiness and its connection with various physical and chemical properties. It appears that a given coal will tend to be dusty ifthe moisture content is low and if the inert maceral content and overall rank are high. The hydrophobicity ofa coking coal (Young-Wallsend) and a steaming coal (Blair Athol) was examined in detail by a dynamic contact angle technique. The YoungWallsend coal had a higher contact angle, on average, than the Blair Athol sample. This result has important implications for dust suppression and associated processes.

Jan 1, 1986

By S Jokanovic, J L. Mauk

The Taharoa ironsand deposit covers approximately 16 km2 and is located 144 km south of Auckland on the west coast of the North Island, New Zealand. The heavy mineral-rich sands predominantly contain titanomagnetite, ilmenite and hematite, along with lesser amounts of amphiboles, pyroxenes, and feldspars. Throughout the Taharoa mine site 142 samples were collected of which approximately 25 samples were used in mineralogical analyses of the magnetic, heavy non-magnetic and light non-magnetic fractions. Mineralogical and petrographic analyses confirmed the high abundance of homogeneous magnetite and magnetite containing ilmenite exsolution lamellae which have oxidised to hematite. A limited number of sand samples were collected from Taranaki beaches. Petrography reveals exsolution textures of magnetite and ilmenite (now hematite), and homogenous magnetite grains similar to those observed at Taharoa. Petrographic analyses from previous research projects were also closely investigated in order to make mineralogical comparisons from along the west coast of the North Island and with other potential source areas. The origin of detrital magnetite grains along the west coast of the North Island is generally presumed to be the eroded volcanic cones of the Egmont volcanoes and active and dormant volcanoes of the central North Island. Electron microprobe analyses of magnetite grains from Taranaki beach samples reveal TiO2 values of between 1.5 and 120 per cent. MgO and A12O3 contents also vary widely from 0.75 to 6.5 per cent. This large variability may reflect different volcanic eruptions, the presence of exsolution textures or alternative source areas for these magnetite grains. Geochemical results from the Taharoa mine site correlate with the Taranaki beach samples suggesting that the Egmont volcanoes are certainly one source area. Variability in XRF results, especially Fe and Ti contents (9.04 - 59.22 and 0.80 - 4.64 respectively), from the magnetic and heavy non-magnetic fractions likely reflect the detrital nature of this deposit.

Jan 1, 2003

By F. X. Spachtholz

"Raw materials industry is crucial for national economy. German mining companies are known for their high degree of resource efficiency based on modern technology and know how. K+S is one of the world’s leading suppliers of standard and specialty fertilizers. In the salt business, K+S, with sites in Europe as well as North and South America, is the world’s leading producer. The mine sites of K+S are distributed all over the world producing mainly potash and magnesium salts and rock salt. Focus is on the sustainable use of the natural deposits in order to stay competitive. For this reason a raw material policy, both national and international, is necessary to ensure access to new mineable deposits which are still available in Germany. Further on, knowing market conditions is a must for sustainable development. At least sustainability and resource efficiency in potash and rock salt mining are achieved by constantly developing new technologies as well as optimizing the organization and improving qualification of workers."

Jan 1, 2011

By Gene Mattila, Ron Boyd

Introduction Rock bolting is a general term that encompasses pinning, roof bolting, rib bolting, and cable bolting. Rock bolting contributes the highest nonproductive cost and is the most significant safety risk in mining today. Total installed bolt costs are now more than $20 per bolt. Rebolting or repair work doubles this. And bolting accidents account for about 30% of all fatal and nonfatal lost time accidents. It is only logical, then, for the mine operator to install the highest quality anchors possible. Every bolt on the market - tensioned, untensioned, full contact, or point anchor - has designed capabilities in axial, shear, and fluctuating ground conditions. Bolts will provide a designed support if material specifications and installation procedures fall within the manufacturer's recommendations. This also assumes that there are no unexpected geological or operational changes. Proper material specifications and installation procedures should guarantee the mine operator a quality anchor. To help assure this, the Mine Safety and Health Administration (MSHA), the US Bureau of Mines (USBM), and the AMC Manufacturers group developed stringent ASTM materials standards. These govern mechanical point anchor bolts and bolts using threaded and nonthreaded rebar. There are also minimum standards that suppliers must comply with in the manufacture of frictional bolts. However, most frictional bolt standards are based on the manufacturer's own specifications. It would be impossible to set uniform regulations on frictional bolts. Each bolt provides support in a slightly different manner and thereby requires different material needs. Quality Control In any case, material quality can generally be assured through tight order specifications and periodic quality control checks. The problem with installing quality anchors does not solely lie with the material. It includes all the events that occur from the time a bolt leaves a manufacturer to the time it is installed. The anchoring ability of any major type bolt can be affected by transportation, storage, mechanical performance of installation equipment, installation demands of the operator, proper drilling accessories, and local geology. Table 1 and Fig. 1 document the negative events that can affect each bolt and the degree to which it can be affected. Drilling a hole of oversized diameter, for example, is an operator controlled factor. It will adversely affect most bolts. An over-sized diameter reduces, or even eliminates, the anchorage capability of a mechanical shell. It will reduce the support capacity of a split set to nearly nothing. And it will cause a partial or incomplete grouting around the resin bolt. Frequently, due to bit wear, holes are drilled undersized in diameter and may not be properly cleaned out. In this case, it will be difficult for the operator to push the mechanical shell into the hole, thereby causing him to drill another hole. In cases where the bolt is obviously not providing anchorage, operators will probably drill another hole and place another bolt. Rock Bolt Regulations It is the situations where a bolt is improperly installed in the hole, but gives the appearance of a good bolt, that are frightening. In fact, some safety officials and engineers believe that only 50% to 60% of installed bolts are working. These bolts cause irregular ground load transfers in other bolts and overload them. This causes hazardous situations and overstressing. It is these bolts that fail prematurely 200 to 255 mm (8 to 10 in.) behind the face and possibly contribute to the high accident rate. The government and several manufacturers recognized the need to check the integrity of rock bolts. These programs are in different stages today. Tight torque regulations have been established for mechanical

Jan 4, 1985

By H. E. Criner, M. G. Driessen

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By M. G. Driessen, H. E. Criner

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By Lyman G. J

Dense medium drum separator efficiency was analysed at two Western Australian iron ore concentrators. Efficiency data had hitherto been difficult to accumulate due to the high cost of analysing representative, and therefore large, coarse ore samples. To overcome this problem, recoverable density tracers, which are in effect artificial mineral and gangue, were manufactured in three different sizes (15 mm, 30 mm and 60 mm). Their use enabled partition curves to be studied within one hour of conducting a test: separation densities were generally lower than the feed medium density for all three sizes of density tracer. For a given set of operating conditions, the smaller tracers had lower separation densities and larger ecart probab/es than the large tracers. These phenomena are explained with the aid of a conceptual model of a drum separator, which assumes that the feed ore plunges to the bottom of the drum upon introduction. Particle rising velocities are, therefore, process determining.Medium rheology was altered by adjusting the proportion of solids in the pulp. This was accomplished by changing both the pulp density and ferrosilicon/magnetite ratio. Higher solids volume fractions invariably caused a decrease in separation densities and an increase in ecart probables, most markedly for the smaller tracers. A similar response was observed when feed tonnages were raised.An explanation for these phenomena is sought in the discussion which also suggests means of improving drum separator efficiency.

Jan 1, 1987

By René Lefebvre

Numerical simulations of the physicochemical processes related to acid rock drainage (ARD) in the Sugar Shack South rock pile of the Questa Mine were performed with the TOUGH AMD simulator. The objectives were to 1) identify the main processes responsible for observed present-day conditions, 2) provide an estimate of gas phase humidity transfer, and 3) give a preliminary indication of the potential impact of closure involving the installation of an alluvial soil cover. Modeling results indicated that the mine rock geometry (thin layers placed along steep mountain slopes) favors the onset of strong thermal air convection. Simulations also indicate that resloping the piles would not significantly reduce convection and oxidation. For simulation purposes, a potential cover with the permeability range of a local alluvium was investigated and found to be of questionable effectiveness since its permeability can exceed the value of 3x10-13 m2 required to prevent thermal air convection and reduce ARD.

Nov 1, 2002

By H. Soto, J. Jara, F. Nava

"A combination of oxidation and precipitation was used to eliminate cyanide from gold milling effluents. Preliminary laboratory work developed with both synthetic cyanide solutions and with industrial effluents indicated that ozone can easily destroy free cyanide and weakly complexed cyanide (i.e. copper and zinc cyanide). In this case the reaction is quite fast and seems to be controlled by the mass transfer of ozone to the solution. Experimental results indicate that free cyanide and weak-acid dissociable cyanide in mill effluents can be reduced to less than 1 ppm. However, the iron-cyanide complexes proved to be quite resilient to destruction with ozone and they remained in the solution even after most of the free and weakly complexed cyanide was destroyed with ozone. These results were confirmed in a pilot trial developed at the Sphinx plant in northern Quebec.To deal with the problem presented by the presence of the iron complexes two different approaches were studied: use of a combination ozone-ultraviolet light oxidation, and the precipitation of iron-ferrocyanide complexes in the residual solution after ozonation. This last method proved quite promising since reduced the total cyanide levels of industrial solutions assaying as much as 250 ppm to less than 1 ppm of total cyanide. Control of the · pH of the solution was the key to obtain the precipitation of the iron complexes. The use of iron to precipitate cyanide complexes has the advantage of being less expensive and less toxic than copper (used by the Inco process)."

Jan 1, 1992

By Don Peel

Mineral aggregate, the most widely used mineral resource globally, has attracted little academic or public interest. Of all mining developments, the aggregate resource is seldom factored into resource management decisions. This lack of recognition to the strategic aggregate resource has significant economic, environmental, and social implications. Impact to the economics, the environment, and the community coincide with the key elements of the United Nations concept of ?sustainable development?. To build on the concept, the mining sector contracted the International Institute for Environment and Development to assess how mining activity contributes to sustainability. As a result, a useful assessment process was developed by the Mining, Minerals and Sustainable Development (MMSD) Task Group entitled ?Seven Questions to Sustainability: How to Assess the Contribution of Mining and Mineral Activities.? In Alberta, recent opposition to mineral resource development by community residents offers an opportunity to employ the MMSD?s assessment procedure. The public opposition to the mining activity was addressed through a stakeholder planning process initiated by the municipal council of Sturgeon County, Alberta. As a result the Calahoo/Villeneuve Area Structure Plan (CASP) was formulated and adopted. To measure the effectiveness of the CASP planning process in terms of sustainability, this paper applies the MMSD?s Seven Question assessment to the Calahoo/Villeneuve Area Structure Plan.

May 1, 2004

By John Watson

New Technologies, New Challenges and New Opportunities For quite some time now, numerous explosive manufacturers have spent untold man-hours and millions of dollars trying to develop a blast initiation technology that would “once and for all” provide users with what was once believed to be only a theoretical possibility...nominal timing. Zero “cap scatter” (the amount of variation of delay timing from the targeted nominal) has been the industry’s goal ever since delays were first introduced into the marketplace. Just as adding delay time between blast-holes improved blast performance since their introduction, having the wrong delay or a poorly timed blast has proven to be very inefficient and in many cases hazardous. The question of how precise a blast initiation system needs to be still remains unanswered, but electronic detonator systems being used today indicate that significant improvements can be achieved over conventional pyrotechnic detonators. These systems can typically provide single digit millisecond ranges of variability, if not sub-millisecond in some cases.

Jan 1, 2003

By Andrew E. Nevin

The government of India convened a precedent-setting meeting in New Delhi on Nov. 12, 2001.The meeting brought together regulators and the mining industry in an attempt to fix the industry’s mine development problems in that country. More than 150people attended the all-day session. Ram Vilas Paswan, Minister of Coal and Mines, chaired the meeting. Ravi Shankar Prasad, Minister of State for Coal and Mines, was also present. The secretary of the Department of Mines and the Joint Secretaries and Additional Secretary also participated. The Department of Mines’ mandate is for economic growth: to get new mine development going and to make investment in mining attractive for both domestic and foreign-owned companies.

Jan 1, 2002

By Yasunori Kosaka, Junya Tokita, Aramaki Shosaku, Inoue Junji

Light ANFO that satisfies blasters and customers who want to reduce the amount of explosive consumption without changing blasting effects and designs and passes Cap sensitivity test regulated by law. The reduced loading density of light ANFO reduces the amount of explosive consumption. The loading density of conventional ANFO is 0.X-0.9g/ml, while the loading density of light ANFO is 0.7-OXgiml. The detonation velocity of light ANFO is maintained not to reduce blasting effects. Detonation velocity of conventional and light ANFO using steel tube of inside diameter 36 mm are 3200 - 37OOms. detonation velocities are the same though the loading density of light ANFO is reduced by O.lg/ml. This suggests that the reactivity of light ANFO improves.

Jan 1, 2002

By M. L. Goble

"Inco Metals Ltd. (Manitoba Division) operates a mining, milling, smelting and refining complex, 500 miles north of Winnipeg in central Manitoba. The Thompson Mill is presently operating at 12,000 S.T.P.D. on ore from both underground and open pit mines. The ore is treated in two separate milling and flotation circuits utilizing a common crushing system which is located inside the main mill building. The milling facility employs approximately 43 operating employees, 30 maintenance employees and 20 staff in supervisory or process development roles.In recent years an increasing awareness of the potential hazards of contaminants in the work place has made it mandatory that all employers maintain careful and accurate records of the work environment to which each employee has been exposed during his working career.The importance of this record keeping and general observation of the work place cannot be over emphasized. Proper monitoring of the work place provides an accurate and complete record of the contaminants and physical agents to which an employee is exposed during his work career. This can aid in studies which might be conducted in the future and can also be used as a basis for instituting improvements to the workplace."

Jan 1, 1980