Search Documents

By André Desbiens, Jocelyn Bouchard, René del Villar

"The metallurgical performance of the column flotation process is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a model-based automatic control strategy using froth depth and bias measurements obtained from virtual sensors developed at Laval University. Preliminary pilot plant results on two-phase (water– air) and three-phase system (water – minerals – air) will be presented and eventual industrial implementation of such a strategy as well as the possibility of achieving effective real-time optimization from bias and froth depth measurements will also be discussed.INTRODUCTIONFlotation columns have been widely studied and used in mineral processing for about twenty years. Although a great deal of work has been accomplished to understand the influence of different variables such as froth depth (H), bubble surface area flux (Sb) and bias (Jb) on the metallurgical performance, the measurement of some of these variables is still difficult to be performed – except at the laboratory level – because in most cases, no commercial device yet exists.As a result of this, it is almost impossible to achieve neither efficient control nor optimization of the process at the industrial level, even in open-loop operation. This paper aims at presenting a simple control strategy of froth depth and bias. Description of the sensors used to achieved measurements, preliminary pilot plant results for froth depth control, eventual industrial applications and possibilities for process optimization are also treated."

Jan 1, 2003

The influence of varying amounts of magnesia, silica, and alumina in iron ore sinter on its mineralogy, reducibility index (RI), reduction disintegration index (RDI), physical breakdown (AI and TI), and production properties (coke breeze rate) were examined. It was found that the mineralogy of iron sinter can more easily be predicted from its chemical composition than from the RI, RDI, AI or TI. Anticipating the consequence that varying amounts of MgO and SiO2would have on sinter properties is complex, and not necessarily predictable. High concentrations of Al2O3in the sinter result in high concentrations of the SFCA phase, but with drastically deteriorated properties. This study also confirmed that the form in which fluxes are added to the raw material sinter mixture affects the mineralogy and properties of the produced sinter.

Jan 1, 2010

By A. George Stern

In the examination of bentonitic clay suspensions used for oil-well drilling fluids3/ (and for other purposes, such as a core binder for foundry sand) it is important to have comparative tests for evaluating them. A satisfactory clay for these and other purposes should 'rave the property of forming what is commonly called a "gel," but the measurement of this property has been a real problem. To date the solution has not been satisfactory, and some of the difficulties are considered in, this, paper, which describes a simple form of instrument (identified as an eykometer) for measuring the yield point under hydrostatic conditions of non-Newtonian clay suspensions, including those muds that are thixotropic. An oil-well drilling mud serves several functions, many of which depend on the "gel" characteristics of the mud. Among the more important functions are: (a) To plaster the sides of the hole to prevent caving of the walls; (b) to prevent the loss of the circulating fluid out of the hole by seepage; (c) to carry sand and cuttings out of the hole to the surface as they are formed by the rotary drill; and (d) when circulation of the fluid stops for shut-down or other unavoidable cause, to hold the cuttings in suspension by the setting up of the gel, thereby avoiding the difficulties that result when these cuttings are allowed to fall through the fluid and pack at the bottom of the hole.

Jan 1, 1940

By Iman G. Ghanad

El presente texto describe un nuevo método para el tratamiento de concentrados de cobre con alto contenido de arsénico utilizando el carbón activado como catalizador. Para ello, se realizaron pruebas de lixiviación con concentrados de enargita de tres minas de Chile, Perú y Estados Unidos, donde los resultados señalaron que la disolución de la enargita fue más rápido con la influencia del carbón en la solución lixiviante, incluso después de haber reciclado el carbón.

Sep 12, 2011

By Andrew Howard

As the mining industry moves further into developing countries in search of new resources, its role in international development is coming under increasing scrutiny. This is a trend that is likely to accelerate, along with the potential for headaches among managers in the industry. Public interest in development and environmental issues is rising as faith in “big business” falls. This has strengthened nongovernmental organizations (NGOs) campaigning for sustainable development. And it has put more pressure on banks, governments and development agencies to curb corporate misdemeanors. Developing world governments are also becoming emboldened to reject previously agreed terms they do not consider equitable. The mining industry has begun to formulate a response to these pressures but must go much further. Societal and environmental issues must move from public relations to core strategic thinking. Abiding by rules or codes is not a relevant response. Instead, genuine support for sustainable development is required. This will involve delegating the responsibility for engaging with local communities to on-the-ground staff and developing a dialogue with local stakeholders rather than conducting an initial assessment and disengaging.

Jan 1, 2006

By George Piscsalko

There are numerous methods currently available to assess the integrity of drilled shaft and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity of drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube, or from embedding thermal wires within the shaft. This Thermal Integrity Profile method will be described in detail and one case history will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.

Jan 1, 2011

By M. G. Maruma

The effect of the amount of cold reduction and annealing temperature on the evolution of the texture of AISI 441 steel is reported. The steel was cold rolled by 62%, 78%, and 82%, followed by isothermal annealing of each sample at 900°C, 950°C, and 1025°C for 3 minutes. The crystallographic texture was determined by Phillips X?Pert PROMPD texture diffractrometer. Microstructures were characterized using optical microscopy and scanning electron microscopy (SEM).The results show that sample that received 78% cold reduction and annealing at 1025°C presented the highest Rm-value and lowest ?R-value, which would enhance its deep-drawing capability. In addition, this sample showed the highest intensity of shifted ?-fibre, notably {554}<225> and {334}<483>. It can therefore be concluded that the ?-fibre, which favours deep drawing, is optimal after 78% cold reduction and annealing at 1025°C.

Jan 1, 2013

By D. R. Wilburn

The worldwide budget for nonferrous, nonfuel mineral exploration was expected to increase by 58 percent in 2004 from the 2003 budget, according to Metals Economics Group (MEG) of Halifax, Nova Scotia. The increase comes two years after a five-year period of declining spending for mineral exploration (1998 to2002). Figures suggest a subsequent 27 percent increase in budgeted expenditures from 2002 to 2003. For the second consecutive year, all regional exploration budget estimates were anticipated to increase. The worldwide budget for gold exploration achieved about 50 percent of the total amount budgeted in 2004.This was 68 percent, or US$715 million, higher than the reported 2003 budget. The 2004 worldwide exploration budget estimates for copper increased by 70 percent, orUS$237 million, to US$577 million from the 2003 budget. The budget for nickel exploration increased 52 percent, or US$89 million more than in 2003. The 2004 exploration budget for other mineral targets (primarily cobalt, heavy minerals, industrial minerals and silver) increased114 percent, or US$118 million.

Jan 1, 2005

THE flotation plant at Mount Lyell was erected, primarily, for the treatment of ore from the Lyell Comstock mine. These workings are situated over a mile in a direct line north of the North Mount Lyell mine, and are connected with the Reduction Work at Queenstown by a 2-ft. gauge steel tramway via the Queen River valley a distance of 7 miles. The property was purchased from the Mount Lyell Comstock Copper Co. After the disastrous fire in the North Mount Lyell mine in October, 1912, steps were immediately taken to make Lyell Comstock ore available for treatment, in order to relieve distress caused by any prolonged stoppage of work, and subsequently 13,032 tons of ore, averaging 3.38 %copper, 0.28 oz. silver, and 0.034 oz. gold; were smelted. When operations were resumed at the North Mount Lyell mine, it was evident that there was no economic advantage in smelting Lyell Comstock ore as compared with the higher value North Mount Lyell ore, which was also a better flux for the Mount Lyell pyrites, and that the future of the Lyell Comstock ore depended upon cheap mining and successful concentration of the ore. Therefore, extensive trenching and diamond-drilling was carried out, and a sufficiently large quantity of ore proved available for cheap extraction by open-cut methods. At the same time bulk tests by flotation were carried out at the Minerals Separation testing plant in Melbourne on different classes of ore from the Mount Lyell Comstock mine proper, followed by laboratory tests at Queenstown on all classes of ore available. All these tests demonstrated that the ore was amenable to the process, provided that it was ground finely enough. Plant erection was delayed by the general dislocation of business at the outbreak of war, but finally it became...

Jan 1, 1920

By Martin J. Pedley

The use of soil nailing has grown steadily in the UK over the last 15 years and it has recently become more popular in the Republic of Ireland. This paper presents three soil nailing temporary works case histories where the technique has been used to support steep excavations in difficult ground conditions. It demonstrates the effectiveness of soil nailing when applied in appropriate conditions. Details of design methods and construction techniques are described and those aspects of soil nailing that will benefit from further study and development are identified.

Jan 1, 2000

By Yajie Wang

Traditionally, roof falls are usually attributed to bad roof strata and high vertical stress related to the overburden depth. However, roof falls under shallow overburden depth are oflen caused by a high horizontal stress field. Recent studies have proven that the high horizontal stress field, if existing, plays a major role in roof stability. Also the roof conditions are related to the entry diredions under a horizontal stress field. Questions are: How to orient the entry to a favorable direction to prevent the roof falls? If the entry cannot be oriented, how to support it? Through a case study in mine A, this paper analyzes the horizontal stress effect on roof stability. The guideline for the entry orientation is given based on the results of analysis. Additionally, suggestions are made for those entries that cannot be oriented to a favorable direction.

Jan 1, 1998

Inhibition of Bubble Coalescence by Salts and Sugars

Sep 13, 2010

By Motohisa Kanda

The time and amplitude statistics necessary to adequately describe electromagnetic (FM) noise in mines are illustrated through computer software techniques. They are 1) Allan Variance Analyses (AVA), 2) Interpulse Spacing Distributions (ISD), 3) Pulse Duration Distributions (PDD), 4) Average Crossing Rates (ACR), and S) Amplitude Probability Distributions (APD). These statistics are illustrated using data taken from a rather large store of raw analog data recorded in operational mines. The curves generated for the illustrations characterize the noise environment in the mines from which the corresponding data were taken, and should aid in the design of reliable communication systems for such mines.

Jan 1, 1974

By H. J. de Haan, J. van Lookeren

In view of their size and favorable characteristics, Shell&apos;s heavy-oil fields on the eastern coast of Lake Maracaibo, Venezuela — known as the "Bolivar Coast" — are obvious candidates for the application of thermal recovery methods. During the last decade various methods have been tested, such as steam drive,&apos;, steam soak and in-situ combustion.3 Steam soak was discovered as a promising production method rather accidentally in 1969, during early steam drive testing in the Mene Grande Tar Sands1 When steam erupted at the surface due to breakdown of the overburden, the injection wells were back-flowed to relieve the reservoir pressure. This resulted in high oil production rates, all the more impressive because the reservoir is unproducible by primary means. It was concluded that injection of limited amounts of steam might be a very effective method for stimulation of heavy-oil wells. To obtain information that would be more widely applicable, testing of the process was continued in the eastern part of the Tia Juana field (Fig. 1). Here even more favorable results were obtained than in Mene Grande. This created sufficient confidence to prompt a large-scale project, which was considered essential for an adequate evaluation of ultimate recovery, steam requirements, mechanical problems and economic prospects. To obtain an early answer on the ultimate recovery a fairly depleted area was selected in the western part of the same field ("A" in Fig. 1). The first steam was injected in March, 1964. This paper describes the performance until the end of 1966. The production mechanism and well inflow performance are discussed in some detail. In view of the favorable results obtained so far, steam soak operations have expanded considerably since the start of this project. Presently, five other projects are under way, of which two are about the same size as the one under discussion, with further extensions being programmed. Description of the Project Reservoir Data Shell&apos;s part of the Main Tia Juana reservoir has a proven area of 8,800 acres and an average net oil sand thickness of 130 ft. It contained an initial quantity of 2,750 million bbl of stock tank oil (STOIIP), with an API gravity ranging from 10 to 15 API and a viscosity of 100 to 10,000 cp (at 122F). As a geological unit it is known locally as the Lower Lagun-illas member of the Lagunillas formation, which is early Miocene in age. The sand bodies are believed to be distributary channel sands deposited in a lower coastal plain. Most of the channel sands have lateral and some vertical communication. The field was developed mainly in the period from 1936 to 1950. The ultimate primary recovery is estimated at 18.1 percent of STOIIP, of which 12.5 percent STOIIP had been produced by the end of 1963 from some 540 wells. By then the average pressure had decreased from an initial value of 960 to 550

Jan 1, 1970

By Mark R. Svinkin

This paper deals with application of the wave equation analysis to determine capacities of piles driven in saturated sandy soils. It shows that pile capacity in sandy soils changes with time after the completion of pile driving and depends on the ground water elevation. In saturated sandy soils the setup coefficient ranges between upper and lower curves represented by power functions. For a reliable prediction of pile capacity wave equation input should be adjusted with soil damping. Back calculation of soil damping from known pile capacity performed for five tested piles shows that skin damping coefficient changes with time in the same manner as the pile capacity and can be represented by the power functions for considered damping models.

Jan 1, 1995

By Anthony J. Konya

"This paper was written during part of the author’s student co-op with Cargill Salt at its Avery Islandunderground salt mine in Louisiana. Blasting salt is a unique type of blasting that is different than blasting other rock types. The plastic nature of salt, along with its large swell factor make salt a challenge to blast. The Cargill salt mines use and have tested a variety of different methods for breaking salt in an efficient manner, however these blasting methods are rarely used in other operations nor talked about today."

Jan 1, 2016

By Anthony B. Szwilski, Dalip Sarin, Richard D. Begley

This paper will present the results of an analysis of several abandoned coal mine projects and includes field data for over a dozen different reclamation projects recently completed in the state of West Virginia. The analysis was performed with the objective of summarizing and or classification of the environmental consequences with reference to the characteristics of the mining facilities (surface, underground, etc.). The analysis also addressed the itemized cost of remediation with respect to procedures, environmental concerns and time. The results of the analysis are that each abandoned coal mine site in West Virginia have/had many unique features and in most cases include a combination of environmental concerns that complicate comparisons. The study also revealed that the abandoned mine land program for mines abandoned prior to 1977, that is being financed by a tax on the production of coal, has produced many benefits for the state of West Virginia. This grant program administered by the Office of Surface Mining, has resulted in a high quality methodology of remediation that has been successful for many years in greatly minimizing and/or eliminating environmental concerns from abandoned coal mines.

Feb 24, 1997

From Sept. 22-24, the Las Vegas Convention Center will be home to MinExpo 2008, the world?s largest mining equipment show that comes along once every four years. Sponsored by the National Mining Association (NMA), this year?s show is on pace to be the largest ever. Nearly 1,300 exhibitors have purchased nearly 55,700 hm2 (600,000 sq ft) of booth space. At the center of it all will be some of the most impressive mining equipment that the industry has to offer. And in the shadows of the massive haul trucks, drill rigs and bulldozers, attendees will be able to see the latest and greatest products including hand tools; the latest in automation and robotics; safety and communications equipment; longwall mining equipment; engines and parts; materials handling and processing equipment and services; pollution control equipment; reclamation equipment and services; computer applications; consulting and financial services and more. While many companies will be on hand to display the tried and true, there will also be plenty of new things to see. ?We anticipate that a whole range of new products will be introduced at the show,? the NMA said of the show that has been called the world?s richest deposit of mining technology, services and products. In addition to the show that will take place in Center Hall and North Hall of the Las Vegas Convention Center, MinExpo 2008 includes a conference program with 20 educational sessions that will tackle the most timely and pressing issues affecting the mining industry. Many of the industry?s top professionals will lead the discussions.

Jan 1, 2008

By S Chew, A Bennett, N Di Giorgio, B Osborne

After relining one of two blast furnaces and enlarging its sinter plant in 2009, BlueScope radically restructured its Port Kembla steelworks operation in 2011, shutting a blast furnace and halving its total production. This drastic move in response to unprecedented raw material prices relative to achievable steel prices was like that of many integrated steelmakers worldwide facing similar challenges. The 2011 restructure also saw major changes in the amount and type of iron ores and ferrous burdens purchased, and a fundamental reappraising of ‘value’ in iron ores. This paper outlines the changes to raw materials purchases from 2011 to 2017, how BlueScope has responded to the changes in pricing and raw materials quality, the effect on the sintering and blast furnace processes at Port Kembla resulting from higher gangue content, some of the broad technical and economic challenges faced by steelmakers confronted with lower quality iron ores and how BlueScope is meeting those challenges.CITATION:Di Giorgio, N, Bennett, A, Osborne, B and Chew, S, 2017. Recent Port Kembla experience with iron ore use – sintering and blast furnace, in Proceedings Iron Ore 2017, pp 25–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Selective Removal of Arsenic from Acid Mine Drainage Containing Ferrous Ion Using Sulfide Precipitation Method

Sep 13, 2010