Search Documents

By A Priatna, H Rumbino, T Casten

This paper discusses the progress of the Deep Mill Level Zone (DMLZ) mine from the pre-feasibility study completed in 2005, through commencement of development access in 2008, completion of the feasibility in 2010 and cave initiation in late 2015. This fourth lift of caving in the East Ertsberg Skarn System (EESS) is located 500 m below the currently producing Deep Ore Zone (DOZ) mine and represents approximately half a billion tonnes of ore and around 1900 planned drawpoints, scheduled to be mined at a peak of 80 000 t/d.The paper reviews the mine design, access requirements, planned footprint sequence and major fixed facility installations such as ventilation, oreflow and shops. A discussion of the preproduction development and construction activities and some of the critical technical challenges overcome during this time frame are addressed, as well as the cave initiation process undertaken in late 2015 and the ramp-up of production and progression of caving.CITATION:Casten, T, Priatna, A and Rumbino, H, 2016. Deep Mill Level Zone – from feasibility to production, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 635–644 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Nathan C. Rockwood

THE title of this paper, I understand, was suggested by professional mining engineers as an opportunity for someone to pose problems rather than to offer solutions for them, but the paper will merely attempt to pose some of the production problems of the mineral aggregates industry in such manner as to create professional interest in their solution by the mining engineer, geologist, geochemist and the metallurgical engineer versed in mineral-dressing technique. DEFINITION OF MINERAL AGGREGATES "Mineral aggregates" may be defined as fragments of any rock or mineral used to supply bulk or volume or substance for a given purpose. For example, mineral aggregates are used in portland-cement concrete to provide bulk with the expenditure of the least feasible amount of cement binder. Mineral aggregates are used without portland cement or bituminous binder in highway and railway roadbeds to provide substance, to carry loads. Mineral aggregates are used in filters for water and sewage, to provide substance for the liquid to trickle through. These are only a few typical uses of mineral aggregates. For all these uses, strength, toughness, resistance to abrasion, and durability are usually prime requisites; so, while theoretically mineral aggregates may be of any mineral composition, what really is desired is a mineral composition as nearly inert under the conditions of use as anything of earthly origin can be. EXPLORATION AND POSSIBILITIES OF DEVELOPMENT The distribution of deposits of mineral aggregate is universal, since almost any part of the earth's crust can be used; even the top soil is sometimes used in stabilized surfacing for highways or airport runways. Nevertheless there is ample opportunity for exercise of the talents of the mining engineer and the geologist in finding the particular deposit that will be most economical to develop, keeping in mind such considerations as: (1) quality and mineralogical characteristics of the material; (2) size and permanency of the market; (3) final cost of opening and development of the deposit; (4) selection of location of plant; (5) methods and costs of distribution of the product in comparison with both present and possible future competition; (6) selection of the proper type of operating equipment; (7) estimation of probable waste products and their disposal. These are typical but there are other considerations also. Because profit margins are far smaller than in any comparable mining operation, it is all the more logical to assume that a higher degree of expert knowledge is desirable to make a success of a mineral-aggregates business. The industry has much engineering talent in its operating branch, but it lacks, to a considerable

Jan 1, 1943

By K. Wongaew, R. F. Cook, J. E. Carlson, T. Cleys, C. R. Smith

Steel fiber reinforced concrete segmental rings are the final tunnel lining for approximately 85% of the alignment for a 6.706-meter (22-foot) internal diameter tunnel being built as part of the East Side Combined Sewer Overflow Tunnel Project. This paper describes the approach adopted for the design of the steel fiber reinforced concrete segments, the development of the performance criteria for the segments, and the testing program used to confirm the performance of the materials and segments in the laboratory and in the field.

Jan 1, 2007

By S Adamson

Morphological analysis of alluvial gold recovered from the same segment of a placer by four common commercial methods indicates that gold shape and the presence of quartz intergrowths or sulphide overgrowths substantially influence the recovery efficiency of each method. The amount and types of gold saved by each method varies according to the different hydrodynamic conditions under which each of the methods operates. Reverse circulation drilling has the lowest efficiency and preferentially loses moderate-high flatness gold and intergrown or overgrown gold particles with relatively low density. Gravity riffle, hydraulic riffle, and jigcentrifugal concentrator systems respectively save progressively more of these problematic gold morphotypes, but still lose significant and sometimes substantial amounts (of profit) to the tailings. Because of the differences in recovery efficiency, reverse circulation drilling probably underestimates the grade of most placers and may have resulted in bypassing several economic deposits. Losses to tailings by commercial recovery plants arise from inadequacies in fundamental plant design features. These inadequacies compromise plant efficiency by limiting the ability of plants to simulate the wide range of hydrodynamic conditions necessary to operate effectively throughout placer systems. Incorporation of sand pumps and multiple recovery methods into the more sophisticated plants only partly overcomes these inadequacies. At best, efficiency will be maximised in a few segments of the placer determined by individual plant design, and will decrease progressively upstream and downstream of those segments. Without prior knowledge of the morphological characteristics of the gold to be mined, it is difficult to choose the most appropriate plant design, or to estimate what proportion of the gold will be recoverable by any given plant. If the relevant relationships are not considered beforehand, the recovery plant is likely to lose a significant proportion of the gold, and sacrifice maximum profit.

Jan 1, 2001

By Charolett Hayes, A. L. Russell, Anthony J. Bednar, Jared Smith, Valentine A. Nzengung, Stephen L. Pilcher

The manufacture of Energetics Materials (EM), including maintenance and demilitarization of munitions causes dangerously high levels of explosives residues to be harbored in building features. The two commonly approved methods of decontaminating energetics contaminated equipment and building features are thermal treatment and steam washing. The current regulatory environment is generally becoming more stringent and unfavorable to thermal and steam decontamination because of their adverse impact on air, soil, and water and their ineffectiveness to completely remove accumulated energetics from foundation cracks, internal and external piping, voids in walls and ventilation systems, and internal cavities of fixed equipment. However, chemical destruction of energetics, especially high explosives, is gaining acceptance as a safer, cost-effective and environmental friendly alternative to thermal and steam decontamination. Organic explosives, including nitramines and nitrate esters are oxidized organic compounds that are susceptible to chemical oxidation and reduction reactions. Under suitable conditions, a chemical reagent consisting of sulfur-based bulk reductants (neutralent) commercialized as MuniRem generates highly reactive free radicals that very rapidly degrade many energetic compounds to innocuous end products while stabilizing metals as the insoluble metal sulfides.

Jan 1, 2016

Longwall minim; is a highly mechanized, high productivity mining method that is finding increasing applications in coal. Although the method would be highly advantageous in certain hard rock mining applications it cannot be applied in hard rock because no suitable cutterhead exists for such materials. The wedge longwall cutterhead is a, roller cutter device that is wedge-shaped, with cutters arranged to eliminate the very large normal force ordinarily required to cause such cutters to penetrate hard rock. However, the wedge geometry cannot be extended to a point: special nose cutters are needed to open a narrow slot for the wedge. This report describes the design, fabrication, and successful field testing of these critical nose cutters.

Jan 1, 1974

By Alexander Siefert, Steffen Pankoke

In the development of commercial vehicles as well as of passenger cars, the effects of vehicle vibrations on operating safety, health and comfort can only be predicted by numerical simulation when appropriate occupant models are available. Such models must be based on human anatomy and have dynamic properties of real humans in order to achieve realistic results. Since human dynamic behavior depend on posture and percentile, the occupant model needs to be adjustable to these parameters with respect to geometry and dynamic properties [1,2]. Dynamic Human Finite-Element-Model CASIMIR CASIMIR is a non-linear, dynamic finite-element-model of the human body. It consists of a dynamic model of the upper torso with head, neck, shoulders and arms as well as of a dynamic model of the lower extremity with pelvis and legs. The most important part is the lumbar area with dynamic non-linear models of the lumbar spine and of back and abdominal musculature. The frequency-dependent characteristics of the intervertebral discs and the effects of muscle activation and non-linear frequency-dependent muscle properties are included. In the latest stage of development, CASIMIR has been equipped with a compliant model of the body surface in the contact areas to the seat. This results in a very realistic transmission of static and vibrational forces into the human body, see fig. 1. Intense model verification and validation has been performed in all stages of model development, starting with validation of small components like intervertebral disc, ending with validation of whole-body-vibrations using measurements of the dynamic mass / mechanical impedance [4]. For an in-detail examination of stresses in the vertebral bodies and discs, a non-linear submodel of the lumbar spine with an increased number of degrees of freedom can be coupled to the whole-body-model, enabling the researcher to examine local effects of vibrations and single shocks on the lumbar materials. [ ] Since it is well known that human dynamic behavior is significantly affected by anthropometric data and posture, CASIMIR can be individualized to the anthropometric status of single individuals or to the mean values for specific percentile groups. Furthermore, posture can be adjusted to the seating conditions applicable to a specific vehicle. Posture modification capabilities include the variation of the lumbar lordosis [3].

Jan 6, 2006

By R. F. Shurtz

The problem of estimating the precision of systematic samples from a mineral deposit is attacked by interpolating the quality, or other attribute measured, by using Fourier approximation. Such approximation using trigonometric functions yields a particularly simple expression for the variance of the mean value of the attribute sampled. The increasing volume of publication in which the science of statistics has been applied to the problem of predicting the quality of an ore deposit from sets of samples taken from it might lead one to believe that engineering judgment can be replaced by statistics. There is, in fact, an implicit application of the principle of indifference or of "no advance knowledge" which has been discredited in modern statistical theory and practice. These pages will show that it is not always advantageous, efficient, or safe to apply this principle. This problem will be dealt with by using series of orthonormal functions to describe the distribution of the quality of ore in space as contrasted with the more commonly used distribution of quality as a frequency function. Mining engineers are rarely well acquainted with the use of such series or of the functions comprising them. These uses are commonplace in the fields of communication and information theory and it is not surprising that applications taken from these fields should be found appropriate for the analysis of the information contained in a set of samples from an ore deposit. It is hoped that presentation of the following basic, but incomplete, results will generate wider interest in this method and a fuller development of it as well as of the necessary computational techniques. FUNDAMENTAL PREMISES Random variables in the strictest sense are not very common in mine sampling. The sets of samples are almost always taken systematically and are, hence, not subject to all the laws governing random events. Therefore, unless there is indeed random experimental error in the determinations of quality, the treatment of systematic samples of n members as though they were random samples of n members often leads to calculation of confidence limits for the mean quality which are larger than they should be with the result that unnecessary additional sampling is done. The reason for this will emerge in the following discussion leading to Eq. 24 and its generalization. In order to inquire into such questions on a rigorous basis and at the same time avoid arithmetic complications that would obscure the concepts involved, a one dimensional distribution of quality will be assumed. The quality, Q, in suitable units is expressed as a function of the distance, x, along some straight traverse of the deposit. Such a function

Jan 1, 1967

By Jesse A. Pfeiffer

CPAR, the Construction Productivity Advancement Research Program, is a new initiative of the Corps of Engineers to enhance U.S. construction industry productivity through the development and application of joint-funded research. CPAR seeks to balance the requirements of both the private sector and the Corps of Engineers construction program, to identify research needs that are common to both parties in a partnership for conducting research, and to achieve practical real-world products which will enhance productivity in the construction industry. Increasing costs of doing business has had a major negative impact on much of the nation's industrial base, and research and development (R&D) is among the areas hardest hit. The Congressional Budget Office estimates that since 1984 inflation adjusted R&D outlays in private U.S. firms have risen at an average annual rate of three percent, or about half the rate of gain of the preceding decade. And, despite a significant increase in foreign competition, the portion of gross national product (GNP) devoted to R&D is lower today than 20 years ago. For the case of the U.S. construction industry, the numbers are even more dramatic.

Jan 1, 1989

By A. Kapito

The formation of bainite in steel is dependent on the size of the casting, the heat treatment, and the alloying elements. It is difficult to obtain a fully bainitic microstructure in steels during heat treatment because of its close proximity to the martensite (a?) reaction. The ferrite (a) and pearlite reactions in steels are also rapid and shield the bainite reaction. Alloying elements therefore need to be added to separate the bainite reaction. Boron (B) and molybdenum (Mo) are key elements added to bainitic steels because of their ability to retard the a reaction. Other elements used in the production of bainitic steels are silicon (Si), chromium (Cr), manganese (Mn), and titanium (Ti). In this paper we investigate the effect of alloying elements on the bainite reaction through the use of dilatometry. Dilatometry is a technique that determines phase transformations in the steel and through which continuous cooling transformation (CCT) curves can then be developed. Some initial results are presented of an ongoing study on the development of bainitic steels for railway wheel applications.

Jan 1, 2013

By Pierre Lacoste-Bouchet, Ian Orford, Mike Cooper

"The Brunswick Mine ore requires fine grinding to achieve liberation of minerals. With 25mm slugs as the grinding media in the ball mill, there was a limitation of a P80 of 25 microns on the CuPb regrind circuit. Results from pilot plant testing showed that the separation efficiency could be increased through fine grinding with a P80 of 15 microns.Options considered were the capital expenditure for new fine grinding equipment such as a vertimill or the use of the present ball mill equipment with smaller media. The Wheelabrator Allevard Enterprise (WAE) millpebs product was chosen because it was a smaller media with a distribution of steel pellets between 5 to 12 mm.With millpebs the grinding product was reduced in size from a P80 of 25 microns to a P80 of less than 19 microns. The power draw to achieve the finer grind was 13% lower while the media consumption was 57% higher.The millpebs grinding media was also tested on the zinc regrind mill. The purpose of the trial was to understand what the media consumption and power draw would be with the charge lowered to achieve an equivalent grind as obtained with the slugs. The media consumption was approximately the same and the power draw was reduced by 30%.INTRODUCTIONThe Brunswick Mine ore is a complex Pb-Zn-Cu-Ag sulphide ore with the grain size of the minerals varying from submicron blebs to particles up to several mm in size. The ore is ground progressively finer in stages. The first step of grinding occurs in the SAG mill circuit. The product sizing 80% passing 95 microns is fed to the CuPb prefloat stage (Cormier et al 2002). The tails from the prefloat is then further ground to a P80 of 35 microns for the CuPb rougher flotation. The final liberation for the CuPb circuit takes place in the CuPb regrind circuit. The regrinding mill further liberates the cleaner scavenger concentrate, second cleaner tails and third cleaner tails. The reasoning for the progressive grinding is to achieve fine grinding without having galena over ground due to its high specific gravity that preferentially sends it to the cyclone underflow."

Jan 1, 2006

By E. L. McHugh, J. M. Girard

This paper discusses the results of two recent case studies in which high-tech prototype instruments were used. The first case study describes the results of a ground-based hyperspectral imaging tool used to map the geology of an open-pit mine highwall. The second case study outlines the use of interferometric synthetic aperture radar and how this type of radar can be used in a variety of geotechnical situations. These case studies are part of an on-going research project at the National Institute for Occupational Safety and Health’s (NIOSH) Spokane Research Laboratory. The project objective is to implement engineering controls and design methods in order to reduce the number of injuries and fatalities associated with slope failures at mining operations. Project personnel are hopeful that these new developments in technology will lead to better geotechnical monitoring and design in slope stability and other important areas of rock mechanics.

By G. T. Lineberry

Underground mine development begins with the positive investment decision to mine and ends with the inception of full-scale exploitation. It incorporates all activities, personnel, and equipment required for creation of underground access to a mineral deposit. Because of the depletion of near-surface mineral resources, the reduced mobility of large surface mining equipment, increasingly stringent environmental constraints, and the introduction of promising innovations to rock penetration and rock excavating equipment (e.g., continuous miners, rock borers), under-ground mining is projected to account for an increased share of worldwide mineral production in the foreseeable future. Without proper engineering during the mine development phase, failure of the underground mining project is axiomatic. A frustration attendant to coverage of the complex area of underground mine development lies not only with the need for treatment of the many disparate specialties within the area but even with the lack of systematization of these specialties in what is recognized as a vital precursor to successful mining. Section17 offers insights into (1) the basic principles of the planning and design process, including baseline assessment, reserve determination, premine planning, and subsystem design (Chapter17.1); (2) equipment selection and sizing, with emphasis on exca-

Jan 1, 2008

By Scott C. Vollmer

This paper seeks to examine some of the technical factors influencing the deflection of Mechanically Stabilized Earth (MSE) retaining walls based on the authors' field observation of numerous structures. Excessive deflections can be unsightly and can be perceived as wall failure. Deflections can cause cracking or gapping of the facing units and general misalignment. Deflection of the reinforced backfill zone behind the wall face can result in settlement of the backfill zone and adjacent pavement cracking. Deflections can be the result of excessive movement external or internal to the reinforced soil structure. This paper only examines internal factors affecting wall deflections. External factors such as foundation settlement are not discussed.

Jan 1, 2003

[ ]

Jan 1, 2008

By T. H. Jeffers

The Bureau of Mines conducted a laboratory investigation of copper electrowinning from electrolytes produced by solvent extraction. The purpose of the research was to gain a better understanding of the fundamental relationship between copper electrowinning conditions, anode corrosion, and cathode purity. Processing variables were evaluated in a cyclic semicontinuous system in which the depleted electrolyte was used to strip copper from loaded organic extractant. For the production of high quality copper cathodes, the electrolyte was dosed with cobalt and stripped of organic solvent extraction reagent. An optimum cobalt addition of 60 ppm, and removal of the entrained extractant with activated carbon provided the best conditions for electrowinning copper containing the least amount of lead and controlling anode corrosion. As little as 13 ppm of the entrained organic extractant, LIX 64-N, significantly accelerated anode corro-sion. However, the addition of 1,000 ppm of organic diluent kerosine did not affect anode corrosion. After cobalt dosing and removing the entrained extractant, cathodes containing less than 2 ppm lead were consistently electrowon at widely varied current densities, electrolyte copper and acid concentrations, and temperatures. Dosing of the electrolyte with selected impurities including magnesium, aluminum, manganese, and iron did not affect the cathode purity. However, 0.05 giL of chloride ions markedly increased anode corrosion and the sub-sequent transfer of lead to the cathode copper.

Jan 1, 1985

The Hyde Macraes Shear Zone (HMSZ) is an extensive low angle semibrittle mineralised structure in the Otago Schist Belt, New Zealand. The shear zone is located on the lower limb of a late metamorphic recumbent fold. Structural observations suggests that the shear zone initiated as a high strain mylonite zone and transgressed the ductile/brittle boundary (D4) later in its development. A surge zone at Round Hill is bounded to the south by a NE-SW striking lateral ramp which displaces the hanging wall shear (HWS) by 50 m. Oblique strike slip displacement during surge zone propagation created space for deposition of the sheeted vein complex or stockwork. Quartz recrystallisation in stockwork veins suggests that the veins were deformed in a ductile manner and implies that surge zone propagation may have occurred during late D3 deformation. A macroantiform was produced during D3/D4 shortening below the HWS. Over tightening of the antiform hinge created SW and NE-dipping ramp thrusts. Continued strike slip displacement along the lateral ramp rotated the antiform and associated ramps into a south plunging drag fold. Post-mineralisation (D5) structures include NE-dipping nonna! faults below the HWS and SW-dipping low angle imbricate thrusts above the HWS. The development of these structures was kinematically compatible with normal movement on the HMSZ and is related to mid Cretaceous break up of Gondwanaland in the SW Pacific.

Jan 1, 1992

By George H. K. Schenck

In this decade of the 1.970's it is forecast that eight billion cubic yards of rock will be excavated from 400, 000 miles of new tunnels, drifts and other underground workings in the western world, according to estimates in a report of the Organization for Economic Cooperation and Development (OECD). It is expected that the cost of this work will be in excess of $54 billion in constant 1970 dollars. Most of this underground excavation will be in mining -- 97% of the tunnel length and 89% of the volume - -the balance in construction. In addition to this huge excavating task, in the 18 developed nations of OECD, will be projects in the Communist Bloc and in the developing nations. Underground excavation requires the successful completion of three principle activities: A. Break -- to free rock from the solid work face. B. Remove-- to clear the work area of broken rock. C. Support -- to assure stability of rock surrounding the underground excavation and to eliminate risk of rock collapse. In today's fully mechanized excavation systems, continuous miners, roadheaders or tunnel borers, (A) break the rock loose from the face, and (B) remove broken rock with their mucking devices and load it onto belt conveyors, mine cars, trucks, or any other appropriate haulage system for disposal. Such operations contrast to the more complex, intermittent systems employed when

Jan 1, 1974

There are no large rivers in Western Australia capable of supplying water for processing magnetite ores. If sea water is used there are severe corrosion issues and the requirement to wash the concentrates with potable water. If groundwater is used there is a need to treat the water and sustainability is an issue for large projects because of potential drawdown of the aquifer.If sea water is desalinated the cost of the water is high because of the power requirement. At the same time the necessity to conserve water has lead to flow sheets where all of the tailings have to be filtered to minimise the water requirement.Managing the various water qualities and optimising water recovery and quality has resulted in optimising the water balance and issues meeting environmental obligations. Reverse flotation is a critical final step in reducing the silica level in the final concentrate and requires good quality water.

Jan 1, 2009

By Euler De Souza

This paper presents a study conducted to assess sillmat behaviour during undercut mining and to provide a comprehensive understanding of the effects of arching and sillmat thickness on stability. The design study investigated the effects of such parameters as stope width and height, closure strains, orebody geometry and inclination, wall roughness, fill properties and cure time on the stability of cemented sillmat during undercut mining. Arching effects have been quantified based on centrifuge modeling studies for the different mining conditions. Observations have indicated that the degree of arching is a function of stope geometry, wall roughness, fill cohesion, and wall closure. Arching effects increased with decreasing stope width, increasing backfill cohesion and frictional resistance, increasing wall roughness and with wall closure.

May 1, 2002