Search Documents

By D Fergusson, J D. St George

Highwall stability is a major consideration in optimising opencast mine geometry. It involves assessing the risk of those slope failures that are large enough to have significant cost, safety and/or operational implications. These risks are then balanced against the value of the resource to arrive at an acceptable slope design. Load-deformation models (commonly referred to as ænumericalÆ models) of slopes provide a powerful tool in this decision-making process since they can be verified well before slope failure occurs. This gives the slope designer increased confidence in reviewing designs during excavation, potentially allowing early revision of pit geometry to either increase or decrease safety margins as appropriate. However, these models are not always adopted as they depend heavily on an appropriate choice of constitutive model and material parameters.   A preliminary load-deformation model of a 170m highwall in Solid Energy North (SEN) OperationsÆ Awaroa 4 opencast coal mine in the Rotowaro Coalfield has been prepared. This uses a strain-dependent constitutive model based on laboratory test results, strength parameters developed by SEN and excavation monitoring data. The laboratory testing has included triaxial compression tests on large-diameter fractured samples to characterise the stress-strain response of the closely-jointed soft rock masses that exist in many parts of the mine. Data from the monitoring of a 25m cut made during excavation of a haul road has been used to refine and verify the constitutive model. The resulting highwall model has predicted highwall crest movements corresponding to the excavation of each bench, for comparison with monitored values. Key model outputs are total horizontal movements of about 0.5m near the highwall crest and shear strains of 0.5-0.7% at the locations of potential bedding-parallel shear planes underlying the highwall. Most of the movement is expected to occur as creep rather than as an immediate response to excavation.

Jan 1, 2006

By X. Q. Cao, D. S. Zhang, L. Q. Ma

To solve the support stability control problem for a coal face with large angles along both strike and dip (CLSD), the ’support-surrounding rock’ mechanical model has been developed, which takes into account the impact of the dip angle of the seam on the stability of the support in the strike direction. The mechanical relationships of the critical topple angle and critical slip angle of the support along the strike of the coal face with large dip angle and the support height, support resistance, friction coefficient, and other factors have been derived through the mechanical analysis of support stability in the strike direction of CLSDs in the free state, the operating state, and the special state. The research findings were applied to a fully mechanized CLSD in Xinji Coal Mine. The maximum underhand angle and overhand angle in strike are 42° and 25° respectively, and the maximum dip is 39°. It is calculated that during underhand mining and overhand mining, the critical support resistances for avoiding support toppling are 3723 kN and 1714 kN respectively, and the critical support resistances for avoiding slipping of the support are 7405 kN and 6606 kN respectively. Thus, the selection of type ZZ7600/18/38 hydraulic roof support for the coal face is justified. Measures to prevent sliding of the support and the installation of a limiting stop maintain the support runs in good condition and ensure safe and efficient mining of CLSD.

Jan 1, 2015

By G. St. J. Perrott, N. A. Tolch

"The measured strength of an explosive depends to a certain extent on which it is determined. An earlier investigation showed the relative propulsive strength of dynamites as determined in one type of apparatus, ballistic pendulum.4 The aim of this paper is to precept strength data on these same dynamites determined in another type of apparatus, the Trauzl lead block, and to compare the results with those of the ballistic pendulum. Trauzl lead block have been in use many years for the determination of thy strength of explosives, under moderate confinement.5 The common practice is to shoot 10 grams of explosive, in tinfoil wrapper,- and then to measure the volume of the cavity produced by the shot. The volume of the original borehole is deducted from the gross expansion and sometimes a correction is made for the expansion produced by the detonator. Dry sand is used for stemming the charge.It has been found that the expansion in Trauzl blocks is not strictly proportional to the charge. Naoum5 believed that for scientific accuracy the charge should undoubtedly be regulated to give the same average expansion for each sample tested, but for expansions of 200 to 400 cubic, centimeters the deviation from proportionality is not sufficient to give results appreciably in error.Neubner7 found that the proportionality curve is tangent to the charge-expansion curve at about 300 cubic centimeters expansion, provided that no deductions are made for the volume of the original borehole or the effect of the detonator; the total or gross expansion is proportional to the charge between expansions of 250 to 350 cubic centimeters without serious error."

Oct 1, 1930

By K. K. Murray, D. G. Gelderland

"The pressure oxidation autoclave at the Goldcorp’s Red Lake Gold Mines (RLGM) was commissioned in 1991. Since commissioning, the circuit has been well maintained and its capacity increased to mechanical and gaseous oxygen limitations. With advances in available technology, opportunities to produce more sulphide concentrate and a changing business environment, an optimization project has been initiated at RLGM. A multi-phase approach has been developed to optimize both the operations and economics of the circuit. This paper describes the history and future of the autoclave circuit at RLGM.AcknowledmentsWe would like to thank the operations and maintenance staff at Red Lake Gold Mines for their support and openness of mind to enact changes to enhance the operation. We would also like to acknowledge the members of the integrated team from Red Lake maintence, metallurgy, operations and corporate technical services that did the hard work to push past the status quo in order to advance productivity.OpportunityThe Red Lake Gold Mines (RLGM) pressure oxidation (POx) circuit has been in operation for over 25 years processing the high sulphide content gold bearing minerals. Increased sulphide concentrate production from improved flotation recovery and increasing gold sulphide association at depth has led to the POx circuit becoming a throughput bottleneck. The opportunity exists to process increased tonnages of sulphide concentrates and increase gold production. In order to realize this value, it will be necessary to increase the throughput capacity of the POx circuit.BackgroundThe POx autoclave at the RLGM, commissioned in 1991, was Canada’s first gold autoclave. It was installed to replace the two-stage fluid bed roaster that was built when the Campbell mine and mill were constructed in the late Forties. The circuit was originally designed to process 12.5 t/d sulphide sulphur in about 50 t/d of Campbell flotation concentrate. Following the merger of the Campbell and Red Lake Mines in 2006, the POx circuit started processing flotation concentrate from both Campbell and Red Lake Mills. In recent years, the circuit has been processing about 18 t/d sulphide sulphur in 75-85 t/d flotation concentrate."

Jan 1, 2017

By A. Pratt

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

May 1, 2010

By Clarke DS

The igneous intrusions in SE Papua New Guinea are part of a sub-volcanic to plutonic, high-K calc-alkaline to shoshonitic suite. High-K andesitic to dacitic intrusives on Misima and Woodlark Islands, and shoshonitic intrusives in Milne Bay and the eastern Owen Stanley Ranges are related to late Cenozoic andesitic volcanism. Both suites are associated with epithermal Au-Ag deposits and weak porphyry Cu-Au mineralisation. All significant alluvial and lode gold occurrences in the region are spatially related to intrusions. Intrusions in the D'Entrecasteaux Islands and near Mt Suckling are core plutons related to basement doming, and appear to have no association with either volcanism or hydrothermal mineralisation. The core plutons are not petrochemi:ally distinct from the volcano-re:-ed Intrusions.

Jan 1, 1991

In some parts of the world explosions in mines are more commonplace events. Even in the more developed nations explosions have occurred in recent times. In some cases these mines have significantly lowered their lost time injury frequency rates and as such considered themselves to be ?safe? operations. The consequence of these explosions has been devastating. It is not just the loss of those underground, but also to the families that have lost people in them and the broader community that has lost friends, income, business opportunities, and in many cases support and sponsorships. It begs so many questions, ?What went wrong??; ?Why were the circumstances not foreseen??; ?What could have been done to prevent it??; ?How is it that no one stopped it, reported it, fixed it etc.??. Being held accountable for negligence, should not be overlooked, however this may not aid the processes required to find all the answers. If the nature of explosions is understood, the circumstances and tools to prevent them are readily available then the occurrence and reoccurrence are due to weaknesses or inadequacies of the systems of work or in the implementation of them. This paper restates the fundamentals of gas explosions, examines the options to control the underground environment through ventilation, gas management and monitoring, education and training. Case studies have been used to examine systematic failures in ventilation management. In some of these cases it is not so much, the system that had been developed, but the interpretation and implementation of the system that resulted in the failure and subsequent loss.

Aug 1, 2013

By O. Güven

In recent years, there is an increasing demand on manganese consumption which stems from the important role of manganese in carbon steel production. And the growing need for manganese ores makes the beneficiation of low-grade manganese ores more economical. In this study, the characterization and beneficiation studies were carried out to propose a flow sheet for typical low-grade Turkish manganese ores. For this aim, different gravity separation methods were applied. According to the mineralogical analysis, the major mineral phases are pyrolusite (MnO2) and psilomelane (MnO2) while the major gangue mineral is radiolarite. Gravity separation tests were accomplished by using jigs, shaking table, MGS (Multi Gravity Separator) and in order to obtain products with high Mn ratio, high intensity magnetic separation was also performed. As a result, different combinations of flow sheets were utilized and a concentrate assaying 56.5% Mn with 85 % recovery was obtained.

Sep 1, 2012

By A. Patri, D. S. Nimaje

Wireless sensor networks and wireless communication systems have become indispensable in underground mines. Wireless sensor networks are being used for better real-time data acquisition from ground monitoring devices, gas sensors, and mining equipment, whereas wireless communication systems are needed for locating and communicating with workers. Conventional methods like wireline communication have proved to be ineffective in the event of mine hazards such as roof falls, fires etc. Before implementation of any wireless system, the variable path loss indices for different workplaces should be determined. This helps in better signal reception and sensor node localization, and also improves the method by which miners carrying the wireless devices are tracked. This paper proposes a novel method for determining the parameters of a suitable radio propagation model, which is illustrated with the results of a practical experiment carried out in an underground coal mine in southern India. The path loss indices, along with other essential parameters for accurate localization, have been determined using the XBee modules and ZigBee protocol at 2.4 GHz frequency.

Jan 1, 2015

By J. M. Mutmansky, A. Wang

This paper defines the elements of a basic economic model for decision-making when considering a methane drainage system for an underground coal mine. A drainage system will require significant capital and operating expenses; hence the decision to utilize drainage must be made carefully. The model outlines the basic structure of decision-making and considers the costs and benefits when the methane is marketed and when the methane is vented to the atmosphere. The effects on mine safety and the dust levels in the mine are also considered, both in a general format and as economic variables. Sources of information for executing this decision-making are provided for an actual mine decision.

Feb 24, 1997

By H. Ikeda

INTRODUCTION [Slide 1] The Role of the MMAJ Ladies & Gentlemen, it is a pleasure for me to be able to make a speech at this SME annual meeting, representing the Metal Mining Agency of Japan. [Slide 2] Today’s Topics In my presentation today, I would like to divide my topics into four parts. First of all, I would like to describe the current situation of Japanese non-ferrous metal mining and mineral processing industries in Japan. Secondly, the supply and demand of non-ferrous metals in Japan. Thirdly, I would like to spare some minutes on the overview of overseas development by Japanese mining companies. Finally, since some people may not be sure what the Metal Mining Agency is or what this Agency, I would like to briefly introduce the Metal Mining Agency of Japan.

Jan 1, 2001

By R. N. Tempel, M. Lengke

Arsenic sulfide [orpiment, realgar, amorphous AsS and As2S3] oxidation rates were measured in mixed flow reactors at pH~2 and temperature of 25-30oC. The measured oxidation rates for arsenic sulfide solids by dissolved oxygen are in the range of 10-11 to 10-10 mole m-2 s-1 after being normalized to final surface area. The order of arsenic sulfide oxidation rates decreases at pH~2 from amorphous AsS > realgar > orpiment > amorphous As2S3. In comparison to pyrite, arsenic sulfide oxidation rates are approximately 1.5 to 15 times slower than pyrite oxidation rates at pH~2.

Jan 1, 2002

Tapira Mine (Tapira, MG, Brazil) is the largest phosphate ore and concentrate producer in Brazil. The mine is an open pit, which until recently operated with a large equipment fleet and now uses a smaller fleet operated by contractors. The annual production reaches 17 Mt of ore plus 14 Mt of waste at a stripping ratio of 0.82. Defining the geological boundaries and forecasting the annual production can be a difficult task if not performed on a reliable model. The geological model has been totally reviewed as well as the estimation process. Ordinary Kriging has been used to build the new block model with P2O5 and contaminant grades. After estimation, block model validation and classification criteria definition to assess resources and reserves, the result is given by the life-of-mine plan is defined after pit optimisation and design. The Lerchs-Grossmann algorithm implemented in the NPV Scheduler was used to define the long-term production targets based on the main parameters P2O5 and the contaminants that are just important to the beneficiation process.

May 1, 2010

Three main divisions of the Proterozoic are recognized in the North-West Division of Western Australia. These are referred to, in order of decreasing age, as the Mt. Bruce Supergroup, the Bresnahan Group, and theBangemall Group. The stratigraphy and distribution of each is described, their relative ages discussed, and a brief geological history of the whole area is presented.

Jan 1, 1966

In the late 1970's and early 1980's a considerable number of large scale open pit mines were developed in N.S.W. and Queensland. At the time these mines were planned, the industry was characterised by rising coal prices, rising fuel prices, and a host of other labour and government constraints different to the situation today. Yet some mines have clearly been able to cope with this change much better than others. While one mine may now be expanding and profitable, its neighbour may still be labouring under painful adjustment processes. This paper examines the major reasons for this difference. It suggests more robust criteria for assessment of future projects to reduce their sensitivity to changes outside management control.

Jan 1, 1990

By J. G. Pippenger

The mining industry has been Australia?s major economic driver over the past decade, contributing 8% to Australia?s Gross Domestic Product and 26% of Australian Stock Exchange Market capitalisation. Australia is the world's leading exporter in coal, iron ore, alumina, lead and zinc; and second largest in gold and uranium. While driving the economy, this resource boom has also created a demand for professional and operating talent that has far outstripped the capacity of Australia?s 21 million residents. I moved to Australia some 10 years ago and have not looked back. This unique island continent with its mix of Indigenous and diverse immigrants ? many still proud of their convict ancestry ? has offered life long memories both professionally and personally.

Jan 1, 2011

While the United States and the rest of the world struggles with record-setting oil prices Canadian oil sands producers are ramping up production to meet demand for oil while also fighting against a host of negative images. In recent months, the price of oil has skyrocketed. Most of that oil comes from Saudi Arabia. In Alberta, Canada there are unconventional oil reserves that rival those in Saudi Arabia in the vast Canadian oil sands, sometimes called the tar sands. Proponents of the oil sands say that Alberta?s oil sands can be a secure source of oil and energy for the United States for many years to come. With new mining and drilling projects, the industry has said that it could quadruple its production to nearly 4 million bbl/day by 2020. Time magazine once called the oil sands, ?Canada?s greatest buried treasure that could satisfy the world?s demand for petroleum for the next century.? So why hasn?t the United States embraced this close, politically secure source of energy? Because, getting usable fuel from the oil sands can be a dirty business, say opponents. The oil sands are a combination of clay, sand, water and bitumen. It is a heavy, black, thick oil. Oil sands can be mined and processed to extract the oil-rich bitumen, which is then refined into oil. The bitumen cannot be pumped from the ground in its natural state. Instead, tar sand deposits are mined, usually using strip mining or openpit techniques, or the oil is extracted by underground heating with additional upgrading. These methods require a huge amount of energy and water and produce a large amount of carbon emissions. Environmental groups that have long spoken out against the oil sands projects got some political backing in the United States in June when a group of mayors from large U.S. cities spoke out against the oil sands, as did presumptive Democratic candidate for U.S. president Barack Obama?s senior energy advisor. During a convention of large-city mayors in Miami, FL, Alberta?s oil sands were singled out in a nonbinding resolution calling for national guidelines to track the lifecycle impact of different types of fossil fuels. The resolution urges cities not to use unconventional sources of energy with a large carbon footprint, such as liquid coal and oil shale and oil sands.

Jan 1, 2008

By Cawte D. C, Just G. D, Whitchurch K. D

The stringent marketing specifications included in coal contracts mean that coal producers must supply cleaner and more consistent coal than may have been formerly required. Geostatistics has the potential to aid in the accurate estimation of the washability characteristics of coal. A prediction method, the Kriged Service Variable Approach has been developed.A Computer Aided Drafting and Design system has proved useful in the development and application of the approach. The geostatistical approach has been tested against coal geological and borehole data and applications discussed.

Jan 1, 1987

By Hugo Cabrera-Real

This work investigated the chemical and mineralogical properties of CaO-SiO2-CrOx-CaF2- MgO slags. Synthetic slags were prepared and the effect of the slag basicity (CaO/SiO2) and MgO contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by XRD and SEM-EDS, whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that in slags with CaO/SiO2 = 1, the main Cr-compound was MgCr2O4 spinel, which forms octahedron crystals. Small amounts of CaCr2O4 and CaCrO4 were also observed. It was found that increasing the slag basicity from 1 to 2 the compounds MgCr2O4 and CaCr2O4 were formed together with the Cr(V)-containing compound complex Ca5(CrO4)3F which forms hexagonal crystals. The results showed that the highest chromium concentration levels in the leaching liquors corresponded to slags with CaO/SiO2 = 2, probably owing to the formation of Ca5(CrO4)3F.

Jan 1, 2010

By Mike Muchard

Augered cast-in-place piles are one of the most cost effective deep foundation options available to designers but have been largely underutilized due to skepticism associated with quality assurance and hence capacity. When installed correctly, unit friction values can rival any other competing foundation system. To this end, many means have been implemented to increase confidence in the competence of the foundation. One such method is load testing via the Statnamic test method. This paper presents an overview of the Statnamic test method, advantages and disadvantages of its use, and several case studies where Statnamic testing of augered cast-in-place piles confirmed quality construction, brought about design changes, or proof tested problematic installations.

Jan 1, 2000