Search Documents

WHEN mining and treatment first started at Broken Hill only oxidised ores were available. These ores were rich in silver and lead-the silver mainly existing as chloride and the lead as carbonate.Treatment processes aimed mainly at the recovery of silver, lead being regarded as a by-product, and its recovery, except in so far as it affected silver recovery, was of minor importance.The first ore mined was carted to Terowie and thence railed to Melbourne, being smelted by the Intercolonial Smelting and Refining Co., of Spotswood.The first parcel (50 tons) returned £7442, or £148 16s. per ton to the Broken Hill Proprietary Company.The second parcel of 1053 tons, smelted at the Day Dream smelter, returned 132,142 oz. of silver, but no record is available as to its lead content.These results obtained from two parcels showed that by smelting the ore a handsome profit could be obtained, and Mr. La Monte was engaged to erect two 30-ton Nevada water jacket blast furnaces on Block 13. These furnaces were placed in charge of Mr. P...

Jan 1, 1928

Apparently there is little inclination on the part of mining engineers to supplant the transmission of power by compressed air with it's formidable rival, electrical transmission. No doubt there are many advantages to be claimed for compressed air that render it parculiary well suited for the conditions which characterise underground work.

Jan 1, 1902

By Goldney L. H

The authors review the literature and discuss the application of methods to the design of thickeners for ilocculated metallurgical pulps. The use and evaluation of flocculents is described. Experimental data show that design based upon laboratory settlingdata is acceptable. The economic aspect of design is also discussed.INTRODUCTIONFor many years there has been little change in the methods for the design of thickener installations. While modifications have been made in the method of applying the data all methods have been based on the observee settling rate of the solids. The development of a theoretical approach based on physical data would involve so many variables which affect the settling rate that the more practical approach of direct observation seems unlikely to be replaced as the basis of design.The advent of synthetic fiocculents has introduced a modification in operation which affects design and should be considered. The authors review the subject and attempt to bring it up to date with present day procedure. Until recently the original work of Coe and Clevenger (1916) remained the basis of thickener design. They described their observation of the different zones encountered in settling, namely clarification, feed, transition, and compression or thickening- zones. The solids pass through the transition zone in settling from feed density to some higher density where settling ceases and ·some compression or compaction effect controls. the density obtained. The point at which the settling zone ceases to exist is known as the critical point.

Jan 1, 1959

By L. D. Haig

"The Texada Mill is a unique iron operation producing High Grade sinter iron concentrate and a by-product copper, gold, silver concentrate. The plant is complex and extremely flexible to handle the many varieties of ore. Two iron concentrates are made and blended. A coarse iron concentrate from primary grinding and a fine concentrate after rougher flotation to remove all the sulphides.All the tailings from iron processing are collected, dewatered, reground and floated for additional copper recovery.The entire milling operation has been carried out in all sea water for seven years and mixtures of sea, fresh, and reclaimed water for ten years prior to that.A very stable float results from the use of sea water at the natural pH8. Reagent Consumption is lower and Metallic Corrosion of mill liners and grinding media is actually less than local fresh water or mixtures of fresh and sea water.Marine growth in pipe lines can be periodically removed by violently bubbling high pressure air up through the water filled mains.Location:Texada Mines is located on tide water on the west side of Texada Island 100 miles northwest of Vancouver, B. C.The Island is served by a 30 car ferry, tug and barge and a scheduled air service from Vancouver to a company maintained air strip near the mine.The climate is moderate with about 30 inches of rain during the winter and relatively dry summers."

Jan 1, 1974

By C N. Whata

While there is no specific obligation on the part of any applicant to consult directly with tangata whenua (people of the land), recent cases highlight the need to engage in active consultation in order to avoid serious objections and delay, particularly where a proposal may affect the matters referred to in section 6(e) (Waahi tapu/sacred places) and 7(a) (KaitiakitangaiGuardianship) of the RMA.   The Environment Court has shown some sympathy for tangata whenua where waahi tapu and other significant matters of cultural concern are at risk because of a proposed development. There are several practical steps that can be taken to minimise the potential for serious objection including: ò knowing who to contact and how to contact them; ò demonstrating empathy for the concerns of tangata whenua; ò engaging in proactive consultation, for example meeting at a time and a place that is suitable to tangata whenua, and a preparedness to meet the costs of tangata whenua etc; ò demonstrate an awareness of tangata whenua issues; being aware of the types of mechanisms that are available to remedy, avoid etc adverse effects on matters of concern to tangata whenua.

Jan 1, 1997

By F. S. A. de Frey

The author would like to refer to his contribution to the paper `Design of pillar systems in South Africa' by Ozbay et al. 1. The authors agreed `wholeheartedly that further research, together with carefully planned field trials, in pursuit of this potentially highly rewarding concept' of the small span small pillar method is warranted. On 30 September 2010 the author went underground at the Kroondal Chrome Mine to observe how the concept of smaller spans was being applied. He was pleasantly surprised to find that the typical coal mine bord and pillar sytem was being used very successfully. Although the deepest mining was taking place at a depth of only 450 metres, Kroondal would be an ideal mine to do further research together with carefully planned field trials. At Crown Mines Gold Mine, where the author worked, he was informed that the first recorded rockburst took place at a depth of 635 metres below surface. The depth of the platinum and chrome mines is increasing, with the risk of an excalation in injuries and fatalities due to 'backbreaks' and siesmic activity. The rock engineer at Kroondal was not aware of backbreaks occuring on the mine. It is important that the rock engineers of the base mineral and gold mines get together and give more serious attention to the host rock environment in which the pillars are situated.

Jan 1, 2011

By Hamid Maleki

Roof falls are one of the leading ground control problems that adversely influence productivity and worker safety in underground mines, construction sites, and nuclear waste repositories. To control roof stability problems, the operator needs to have practical methods for measuring changes in strata conditions and criteria for defining the timing of secondary support installation. The objective of this study was to develop measurement techniques and criteria for assessing roof conditions at the mining face. An integrated rock deformation and tomographic imaging method was developed and applied at two sites in a western U.S. trona mine. It was shown that rock damage occurred at a deformation of 30 to 60 mm (1.2 to 2.4 in) (2 to 4 pct strain) and was associated with a significant (16 pct) reduction in wave velocity. Thus, supplementary support may be installed when there is a measured change in wave velocity of at least 16 pct. Tomographic measurements can be obtained in rocks rapidly, thus providing a powerful tool for analyzing growth of failure and for installing supplementary support systems in a timely manner.

Jan 1, 1996

Uranium exploration over a wide area of the Southern Frame Embayment, South Australia, has defined a number of Lower Tertiary fluvial palaeochannels incised in older rocks. The buried channels contain similar stratigraphicsequences of interbedded sand, silt, and clay, probably derived from the adjacent uranium-rich Olarv Provinee. Uranium mineralization is pervasive within two major palaeochannels, and four small uranium deposits have been found in the basal sands of these channel sequences, at the margins of extensive tongues of limonitic sand.One of the channels is examined in detail with respect to channel morphology, stratigraphy, and rock alteration and the geology and ore controls of the contained uranium deposits are described.A geochemical zonation reflected by variation in limonite, pyrite, carbon, and humic malleI' is defined across one of the deposits. A genetic model is proposed suggesting formation by a uraniferous geochemical cell which migrated down the stream gradient and concentrated uranium on its lateral margins adjacent to the channel bank.

Jan 1, 1978

By Morgan W. M

It is not the primary object of this paper to treat with the scheme of prospecting in detail, but it is considered that a brief description of the broad lines is necessary so that the significance of the points to be discussed later may be appreciated.The finding of payable gold reefs on the Bendigo field resolves itself into a two-fold problem, firstly the location of quartz bodies, and secondly the location of gold shoots in such bodies. The country rock of the field has been folded and faulted, and the occurrence of known reefs is associated with the fold axes and the faulting. The "lines" of the field are the anticlinal axes, and practically all known reefs are at or near centre country. Very little work has been done on the synclines, which may have some potential value.Quartz has been introduced along the fracture systems, and gives rise to the three main types of reef met with on the field, namely, the "back," which is similar to a bedded quartz reef and is formed along a bedding plane fault; the "saddle," which forms at the crest of the anticline and has the typical shape from which it takes its name; and "spurs," which are irregular masses of quartz, making off reefs of the first two types.As the fracturing throughout the field is widespread and fairly intense, the first problem, that of finqing quartz, is comparatively simple, and any regular system of blocking out the ground will be productive of quartz bodies.*Field Superintendent, Bendigo Mines Ltd. Assistant Field Superintendent, Bendigo Mines Ltd.

Jan 1, 1936

The No. 2 Ore-shaft, at Mount Isa Mines Limited, involving the use of boreholes as ropeways for the upper portion thereof, constitutes, we believe, a unique feature in hoisting installations. The boreholes were sunk from the surface to a depth of 390 ft., thus eliminating the necessity of erecting the hoist at an underground location or construction of the shaft for this distance. Fig. 1, a diagrammatic cross-section through the shaft, shows the complete installation from the surface down to the first loading station below No. 7 haulage level.During the latter part of 1936, conditions encountered in sinking the Main Ore shaft made it impracticable and uneconomical to continue deepening it to serve haulage levels below the present No. 5-level. Plans were therefore made for an interior shaft, to serve new lower levels, that terminated above No. 5-level so that ore hoisted could be drawn off on this level and transported to the Main Ore shaft for final conveyance to the mill crude ore bin.Referring again to Fig. 1, it is apparent that the section above No. 4-level, if opened out to full shaft size, would be inoperative and would serve no useful purpose except, possibly, as a ventilation duct. Original plans therefore did not include continuation of the shaft above No. 4-level. Excavation of a hoist room upon No. 5-level; erection of sheave wheels just below No. 4-level, and a long inclined ropeway leading from the hoist to the sheaves, were incorporated in the general layout. Work on the lower sectionof the shaft had started when the idea of locating the hoist...

Jan 1, 1939

By A. R. Gaba

Phase I of the Canary Wharf development in London's docklands involves the construction of six fifteen storey buildings located predominantly over water of the West India Docks. The buildings are supported on some 1000 No., 25m long, open ended steel tubular piles driven through 10m of dock water to found in dense sand at a depth of about 15m below dock bed level. The piles are of composite section with reinforced concrete within the upper 17m of the steel tube. Three trial piles were installed in the dock to investigate the driveability and performance of the driven steel tubular piles. The piles were subjected to dynamic and static load testing. Loads were applied in both vertical and horizontal directions. Vibrating wire strain gauges were installed on the inside of the steel piles, on the reinforcement and in the concrete to determine the relative proportions of the applied load carried by the steel tube and concrete infill and to establish how these proportions varied along the length of the piles. Inclinometers were also installed to monitor the lateral deflection of the piles. This paper describes the driving, construction and testing of the three trial piles. The results of the vertical and horizontal loading tests are discussed and comparisons are made between dynamic and static tests carried out on the piles.

Jan 1, 1989

By Jones S. C

A specific arc can be cut in hard rock formations using a specially designed multistep piloI bit, variable sized drift joint and long heavy control rod as a stabilizer rather than the Vaughan Thompson "Lifting" arc cuttingequipment. The rate of deflection can be controlled after an initial determination of behaviour in any particular rock type.

Jan 1, 1966

By J. R. Thoenen, J. D. Warne

"INTRODUCTION Red-iron-ore deposits in northeast Alabama have been exploited at vari¬ous times for nearly 6o years. About 3-1/2 million tons of ore have been produced in the Gadsden district; but mining activity has been dormant since 1926, and furnaces within this section of the State now suffer a shortage of red ore.To alleviate these shortages, work by-the Bureau of Mines was recommended after preliminary investigations. 4/5/ Diamond drilling, to determine the lateral and vertical extent of ores of known deposits in Greasy Cove and on Shinbone Ridge, was done from August 1946 to May 1947, as Project 9-106, Alabama Red Iron Ore. Three holes were drilled in each area.ASKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of domestic mineral resources to the end that they- make the greatest possible contributions to the national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as possible after its conclusion. The Mining Division, Lowell B. Moon, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests."

Jun 1, 1948

The mining industry in Australia frequently uses the services of specialist engineering and managing contractors and consultants for a majority of the work required for project development, from feasibility studies to project commissioning. The project owner's prime objectives are to achieve predictability and competitive advantage for their project. As the majority of this work will be carried out by contractors, the effective evaluation, selection and management of these contractors in the most appropriate forms of contracts is an essential ingredient to project success. The first stage to project development should be for the owner to examine its own resources to establish the role that it will fill and thereby identify the role and scope of contractors' involvement. Once the owner has developed this work plan, the selection of contractors and consultants should be structured to ensure that the owner acquires the appropriate expertise and experience to achieve its project objectives. The sequence of selection procedures is: 1. Pre-qualification of prospective contractors according to the owner's adopted criteria, through the use of a pre-qualification questionnaire. 2. Evaluation by the owner tender board according to predetermined mandatory criteria. 3. Preparation of tender documents for submission to qualified contractors. 4. Evaluation of tender submissions by the owner tender board using a pre-determined, weighted matrix of technical and commercial criteria. 5. Final selection and contract negotiation.

Jan 1, 1990

By Richard P. Sheldon

In the last several decades, techniques of data collection have been rapidly evolving. Automated spectroscopic techniques in the chemical analysis of rocks for example have advanced to the point that we can analyze samples faster than we can grind them. Remote sensors of LANDSAT give us intensity measurements in four color bands of every acre of the U.S. every 19 days. Common depth point seismic instrumentation systems used at sea for surveying and networks of seismometers arrayed around the country for earthquake studies likewise are generating vast amounts of data. These along with many other earth science data generating systems have caused a veritable data explosion. How do we deal with these enormous amounts of geologic data presently being produced as well as those produced in the past, and to be produced in the future? There is an immediate need to acquire and utilize past and present basic data in order to address today's national earth science problems. Also data being collected and stored now must be compatible with future data in order for us to be able to undertake the wide spectrum of analysis that must be made in the future. This is a big order! In order to organize and to be able to analyze these data, the USGS has embarked on a wide ranging program of compatible data base construction and the development of computer technology, based on interactive computing, to facilitate resource assessments and analyses. These activities are analogous to two sides of a coin. One side deals with the logic, philosophy, and mechanics of information storage and retrieval; and the other side deals with the sensible application of computer technology to the treatment of data. These

Jan 1, 1977

By Christopher Jon Preston

This paper describes a type of ammonium nitrate (AN) produced in a patented experimental atomization/aerodynamic process. This AN exhibits outstanding properties for use as a main ingredient to a new family of AN-based commercial explosives. Micro-particle ammonium nitrate (MP-AN) is produced by atomizing either an 83% or 85% AN solution which has been doped with a two component surfactant NSol 1000 (NSol). NSol imparts some water-resistance as well as provides a means of increasing density and bulk strength. Increased detonation velocities, well in the range of emulsion explosives, can be achieved. The maximum manufacturing temperature is less than 100°C. The methodology has the potential of being environmentally friendly since any effluent can be recycled back into a make-up tank to be re-used by the closed loop method. The process has a small footprint.

Jan 1, 2015

By M I. Pownceby, N A. S Webster, R Pattel, N Ware

The decrease in quality of Australian iron ore, coupled with the demand for more efficient energy use, necessitates closer monitoring and optimisation of process conditions for iron ore sinter production. Sinter properties are correlated with the mineralogical content and traditionally, quality control has relied on methods such as Fe2+ determination, point counting via optical microscopy and automated electron beam techniques such as QEMSCAN; these can have a typical turnaround time of several days between sampling and reporting of results. As well, there is additional uncertainty around quantifying some of the complex mineralogical phases in sinter such as silico-ferrite of calcium and aluminium (SFCA) and SFCA-I, which are key phases influencing sinter quality. There is a clear need for the implementation of alternative analytical methodologies that offer a turnaround in hours or even minutes to provide information to accurately maintain production conditions.X-ray diffraction (XRD) is a technique widely used for the quantitative mineralogical phase analysis (QPA) of ores and processed materials in the iron ore industry. Partial least squares regression (PLSR) analysis methods have recently been suggested as an indicator of sinter Fe2+ content from powder XRD data without the need for rigorous and often time-consuming mineralogical analysis by the operator. In this study we provide results from the implementation of PLSR to predict the strength of iron ore sinter. Results are sourced from a well-constrained data set comprising strength properties (as quantified by a tumble index (TI)) from a series of compact laboratory test samples. Using this data set it was determined that PLSR has potential to be used as a method for calculation of sinter TI from powder XRD data and, therefore, process control.CITATION:Webster, N A S, Pownceby, M I, Ware, N and Pattel, R, 2017. Predicting iron ore sinter strength through X-ray diffraction analysis, in Proceedings Iron Ore 2017, pp 331–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

THE IRON HUNTER. By Chase S. Osborn, pp. 316, Ills. 10. The MacMillan Company, New York. 1919. An autobiography, the story of a Hoosier boy who fought his way to manhood and power through early misfortune and poverty, from street urchin and newsboy, to editor and author; from lumberjack and dock walloper to statesman and Governor of Michigan. The reader has the measure of the man in the first chapter, a dramatic recital of how the fighting boy editor cleaned up a lawless mining camp of 40 years ago. The thread of the narrative is the author's life-long devotion to outdoor living, ex-ploration and travel. Residing in Sault de Sainte Marie, Mich., in the heart of the Lake Superior country, he took his delight and, incidentally, found his fortune in prospecting the north woods for iron ore; eventually, extending his travels to the continents and many of the islands of the world, he discovered what, he believes-to be a great iron range in Madagascar. In this book there is plenty of anecdote, a great deal of wholesome social and po¬litical philosophy and some interesting sidelights on the characters of some of the author's prominent contemporaries in the political life of Michigan. The style is direct and animated, flavored and illuminated with the vernacular of Hoosierdom and the woods country of the North. The author levies on the vocabulary of the sciences and the classics for many a noun and adjective and, with Rooseveltian license, now and then coins a word. The reader's interest will be gripped from cover to cover, albeit he may occasionally need a dictionary. R. C. A.

Jan 11, 1919

By S. K. Kawatra, A. K. Bakshi, T. C. Eisele

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle's Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By Roy C. Fedotoff, Jon Hurt, Gregg Sherry, Gilbert Tang

The 1,380 m (4,200 ft) long New Crystal Springs Bypass (Polhemus)Tunnel (NCSBT) will replace the existing Crystal Springs Bypass Pipeline. This tunnel project is part of the SFPUC’s $4.3 billion capital improvement program to repair and seismically upgrade their aging pipelines, tunnels, reservoirs and dams that provide drinking water to more than 2.4 million customers in the San Francisco Bay Area. This paper describes the development of the tunnel alignment and design, and the complex ground conditions of the Franciscan Mélange. Of particular interest is the challenge of tunneling with a possible downhill grade of 3%, a rigorous environmental process and incorporating the lessons learned from 1960s construction of the adjoining Crystal Springs Bypass Tunnel.

Jan 1, 2007