Search Documents

By Dennis A. Hansen

As part of a U.S. Bureau of Mines program to develop a more continuous titanium metal extraction process that uses domestic resources, a study was made to determine the extraction of titanium (Ti) and iron (Fe) from New York rock ilmenite using fluosilicic acid (H2SiF6). The effects of leach temperature, acid concentration, and particle size were investigated for the rate at which Ti and Fe are extracted from the ilmenite. Within the leach time studied, the extraction data fit a shrinking-core model; the rate-controlling step was diffusion of H2SiF6 through an ash layer resulting from a heterogeneous leaching reaction. The rate is linearly dependent on the H2SiF6 concentration and is inversely proportional to the square of the particle diameter. Using 2.6M H2SiF6 at 85°C, 49% of the Ti and 53% of the Fe in 44-to 74-µm New York rock ilmenite were extracted in 3 h.

Jan 1, 2010

By Michael E. Henderson

Presented in this report are the experimental results of coarse coal slurry degradation data obtained from the Hydraulic Transport Research Facility (HTRF) at the Pittsburgh Research Center (PRC), Bruceton, PA. The facility is operated by Boeing Services International, under Bureau of Mines Contract No. J0333956. Presented in this report are the experimental results of coarse coal slurry degradation data obtained from the Hydraulic Transport Research Facility (HTRF) at the Pittsburgh Research Center (PRC), Bruceton, PA. The facility is operated by Boeing Services International, under Bureau of Mines Contract No. J0333956. This particle degradation report is a summary of the particle distribution data obtained at the HTRF for the period 26 November 1982 to 1 October 1983. The testing covered herein is for coarse Pittsburgh Seam coal in the 6-in (150 mm) and 12-in (300 mm) pipelines, at velocities ranging from 5 to 18 ft/s (1.5 to 5.5 m/s), and at concentrations by weight ranging from 15 to 55 pet. Particle size distribution samples were taken systematically throughout the testing.

Jan 1, 1985

By G. E. Agar, W. B. Kipkie, R. A. Tenbergen

"This paper describes the successful pilot plant testing of a flowsheet, developed at INCO Ltd.'s J.Roy Gordon Research Laboratory (JRGRL), for improved separation of the constituent minerals in a bulk copper nickel concentrate.The flowsheet utilized the fact that xanthate concentration on the mineral surfaces is the most important variable affecting the high lime separation and that reduction of the xanthate concentration could be effected by an oxidative conditioning stage.When the adsorbed xanthate was reduced to a suitably low level, chalcopyrite and pyrrhotite could be floated to leave a high grade nickel concentrate as the residue. Sodium cyanide was added to the froth product to depress pyrrhotite and any remaining pentlandite. The temporary depression of chalcopyrite by the sodium cyanide was overcome by introducing a conditioning step following cyanide addition. The advantages of the flowsheet; improved copper-nickel separation, operation without heating of the pulp, production of both high grade nickel concentrate ( 29. 5% Ni, . 26% Cu) and copper concentrate ( <O. 5% Ni, 30% Cu) were all realized."

Jan 1, 1984

By G. S. Scott

[The Duretiu of Kinen, as :) pr<r"Yof its :;encr:rL propan clealini: with the causes, behavior, n.ncl tor-trol of o1:t1?;.?cite-mine fires, hns investic:&apos;lte3 I varionr. Te:.nr, for Je tec tin:: iccj.r)ic:~ t he;, tint; :,:.zqdergro-.:rid and of <~e termining the trend of the hen tir..: once -I i&apos;i re j 7 knnm tr, he nrcsc~t.]

Jan 1, 1938

By Varadarajan Seshadri

A physical model based on similarity principles was constructed for simulating the RH degasser of CST (Companhia Siderurgica Tubarao, Vitoria, ES, Brazil) to evaluate the circulation rate of the metal which essentially defines the degree of exposure of the metal to vacuum in the chamber and thus of the refining rate, The circulation rate on the other hand will influence the decarburization rate and removal of dissolved gases like nitrogen and hence it is essential to optimise this parameter to get maximum refining efficiency with minimum refining times, thus improving the productivity of the secondary refining process. Mixing characteristics in the ladle is evaluated by pulse tracer addition using conductivity-meters located at the down leg as well as at several locations in the ladle. The influence of gas injection through nozzles in the upleg with simultaneous bottom injection of gas as well as nozzle blockage on the circulation rates were investigated. Also simulation experiments of kinetics of decarburization were carried out using CO2 adsorption-desorption process in sodium hydroxide solution as circulating fluid and the effect of, bottom gas flow rate in this case was also evaluated. The results were carried over to prototype and to optimize the process.

Jan 1, 2003

Aamot, Olav Crone, (Member &apos;29) Met , Det Norske Aktieselskab for Elektrokemisk, Industry, Inc , Oslo, Norway Aase, Glenn D , (Junior Member &apos;40) Met Engr , Western Research Dyv , American Smelt & Refin Co , Selby, Calif Abadye, Henry G., (Member &apos;43) Petr Engr , Sr Prod Engr , Long Beach Oil Development Co, 255 So Santa Clara Ave, Long Beach, Calif Abbott, Clarence E , (Member &apos;04) Civil Engr , &apos;P , Tennessee Coal, Iron & R R Co , 1542 Brown Marx Bldg Birmingham, Ala Abbott, Fred E , Jr , (Member &apos;44) Petr Engr , c/o Arabian American Oil Co , A P 0 816, c/o Postmaster, New York, N Y Abbott, John H , (Member &apos;46) Resident Mgr , Hickman, Williams & Co, 230 No Michigan Ave, Chicago 1, Ill Abbott, R W R., (Member &apos;47) Asst Power Supt, Cananea Consolidated Copper Co , Cananea, Son , Mexico Abbott, Robert H? Jr., (Junior Member &apos;47) Petr Engr, Producing Dept, The Texas Cc, P 0 Box 951, Houma, La Abel, Raymond L., (Member &apos;28) Chem Engr, Prof of Chem Engrg, Univ of Pittsburgh, Pitts¬burgh Pa Abel, Walter D , (Member &apos;32) Min Engr, Div of Corporations, 403 State Bldg , Los Angeles 12, Cal if

Jan 1, 1952

By D. J. Chaiko

Aqueous biphasic extraction (ABE) processes offer the potential for low-cost, highly selective separations. This countercurrent extraction technique involves selective partitioning of either dissolved solutes or ultrafine particulates between two immiscible aqueous phases. The extraction systems that we have studied are generated by combining an aqueous salt solution with an aqueous polymer solution. We have examined a wide range of applications for ABE, including the treatment of solid and liquid nuclear wastes, decontamination of soils, and processing of mineral ores. We have also conducted fundamental studies of solution microstructure using small angle neutron scattering (SANS): In this chapter we review the physicochemical fundamentals of aqueous biphase formation and discuss the development and scaleup of ABE processes for environmental remediation.

Jan 1, 1996

By G. S. Scott

[The Duretiu of Kinen, as :) pr<r"Yof its :;encr:rL propan clealini: with the causes, behavior, n.ncl tor-trol of o1:t1?;.?cite-mine fires, hns investic:&apos;lte3 I varionr. Te:.nr, for Je tec tin:: iccj.r)ic:~ t he;, tint; :,:.zqdergro-.:rid and of <~e termining the trend of the hen tir..: once -I i&apos;i re j 7 knnm tr, he nrcsc~t.]

Jan 1, 1938

By André L. B. Bittencourt

The copper content in the waste slag represents the greatest loss in the process of Caraíba Metais&apos; Smelter. By identifying the variables responsible for copper stabilization in the slag, a minimization on these losses is expected, producing a granulated waste slag with a copper content lower than 0.7%. Statistics resourses such as control charts, Pareto&apos;s diagram and correlations curves were applied for the data obtained in the first semester of 1992. The magnetite and the calcium oxide contents in the slag of the Flash Smelter Furnace were most prominent variables. Some operational changes introduced during and after this investigation have shown good results.

Jan 1, 1994

By JOHN HOMER, Jacob L. Carr, Jonathan K. Hrica, Kathleen M. Stabryla, Iman Benbourenane, Jennica L. Bellanca

Given the recent focus on powered haulage incidents within the US mining sector, an appraisal of collision avoidance/warning systems (CXSs) through the lens of the available research literature is timely. This paper describes a rapid review that identifies, characterizes, and classifies the research literature to evaluate the maturity of CXS technology through the application of a Technology Readiness Assessment. Systematic search methods were applied to three electronic databases, and relevant articles were identified through the application of inclusion and exclusion criteria. Sixty-four articles from 2000 to 2020 met these criteria and were categorized into seven CXS technology categories. Review and assessment of the articles indicates that much of the literature-based evidence for CXS technology lies within lower levels of maturity (i.e., components and prototypes tested under laboratory conditions and in relevant environments). However, less evidence exists for CXS technology at higher levels of maturity (i.e., complete systems evaluated within operational environments) despite the existence of commercial products in the marketplace. This lack of evidence at higher maturity levels within the scientific literature highlights the need for systematic peer-reviewed research to evaluate the performance of CXS technologies and demonstrate the efficacy of prototypes or commercial products, which could be fostered by more collaboration between academia, research institutions, manufacturers, and mining companies. Additionally, results of the review reveal that most of the literature relevant to CXS technologies is focused on vehicle-to-vehicle interactions. However, this contrasts with haul truck fatal accident statistics that indicate that most haul truck fatal accidents are due to vehicle-to-environment interactions (e.g., traveling through a berm). Lastly, the relatively small amount of literature and segmented nature of the included studies suggests that there is a need for incremental progress or more stepwise research that would facilitate the improvement of CXS technologies over time. This progression over time could be achieved through continued long-term interest and support for CXS technology research.

Jun 17, 2022

By B. O. Odera

The Pt-based alloys have a high potential for replacing some Ni-based superalloys (NBSAs) used in the highest temperature and most aggressive environments, and vanadium would be a beneficial alloying element. Six alloys of average compositions Pt-26.6Al-9.1V, Pt-23.1Al-17.8V, Pt-9.6Al-21.1V, Pt-17.4Al-6.4V, Pt-22.3Al-7.9V, and Pt-6.0Al-10.1V (all in at.%) were manufactured by arc-melting and examined in the as-cast condition using scanning electron microscopy and X-ray diffraction (XRD). Five samples were heat treated at 1 000°C for 1 500 hours and water quenched, then examined. The phases were identified using energy-dispersive X-ray spectroscopy and the identities were confirmed by XRD. In most of the samples, the phases existing in the as-cast condition were different from those at 1 000°C after ~1500 hours heat treatment. A solidification projection, an isothermal section and a liquidus surface projection were determined for the Pt-rich corner.

Jan 1, 2012

By Y. Q. Li, Z. C. Shen, C. H. Zhao

The dynamic properties of the KYF-320 flotation machine which is one of the biggest flotation machines in the world were tested and then verified by the computational fluid dynamics (CFD) simulation. Aeration rate testing results suggest that he effect of circulation holes on the fluid state in the flotation cell becomes gradually smaller when the impeller speed is greater than 107 r/min. The dispersion degree of air increases with the increasing impeller speed and decreases with the increasing aeration rate, and it increases slightly when the impeller speed is greater than 107 r/min. The air holdup increases and then decreases with the increasing impeller speeds and aeration rates, and a maximum value of air holdup is shown at impeller speed of 107 r/min with a value of 12.28%. CFD simulation results are in good agreement with these testing results. Industrial-scale test was carried out using this 320 m3 flotation machine for the flotation of Cu ores. The results show that Cu content increases from 0.06% of crude ore to 1.26% of concentrate, and the S content increases from 0.39% of crude ore to 24.83% of concentrate. Moreover, using this flotation machine 5.88% of power is saved compared to other type of large flotation machine.

Jan 1, 2015

By C. P. Mabie

This report summarizes studies by the Bureau of Mines in developing a simple method for estimating the phosphorus pentoxide (P205) content of finely ground sedimentary phosphate ores and beneficiated products. The method used involved leaching, filtration, and precipitation. The Bureau found that measurement of the volume of ammonium phosphomolybdate precipitate obtained from samples containing 16.8 to 37.7 percent P205 and the use of an appropriate calibration curve permitted estimates of percentage of P205 content accurate within ± 1.1 to ± 2.6 percent, respectively, at the 95-percent confidence limits. Incidental to mineral dressing and petrographic investigations of western phosphate ores in 1959, the Bureau of Mines undertook development of a simple process-control method for rapid on-the-spot evaluation of phosphate-mineral recovery. Because of the fine-grained and obscure character of western phosphate ores, chemical, rather than microscopic or petrographic, techniques were investigated. The described method involves acid decomposition of the ore or product, filtration, addition of ammonium molybdate reagent to the filtrate, and centrifuging and measuring the volume of yellow ammonium phosphomolybdate precipitate produced.

Jan 1, 1961

The negative effects of pyrite and pyrrhotite on thiosulfate gold leaching have been investigated. Possible remedies to reduce some problems are discussed. In a gold bearing pure silicate ore, 92% of gold could be extracted within 3 hours using a solution containing 0.2 mol/L ammonium thiosulfate, 0.9 mol/L ammonia, 30 - 300 ppm copper sulfate and 8.6 ppm dissolved oxygen at pH 10.26. The thiosulfate consumption was 7.1 kg/t under these conditions and could be further reduced to 3.5 kg/t by decreasing the dissolved oxygen to 0.3 ppm. Addition of 16% pyrrhotite or pyrite into the silicate slurry led to a decrease in gold extraction by 2% or 9% respectively and an increase of thiosulfate consumption by 11 kg/t or12.8 kg/t respectively in three hours. Several adjustments, such as increasing copper ion and ammonia concentration and reducing the dissolved oxygen level to 0.3 ppm resulted in increased gold extraction and lower thiosulfate consumption despite the presence of these sulfides.

Jan 1, 2005

By Batric Pesic

Solvent extraction of nickel and cobalt from the real leach solutions was studied by using a novel extraction system. The extraction system was a mixture of 2,6-bis-[5-n-nonylpyrazol-3¬y]] pyridine (BNPP) and dinonylnaphthalene sulfonic acid (DNSSA). The BNPP represents a novel molecule, which was designed and synthesized in our laboratory. Real solutions for the study were prepared by leaching of two different cobalt-nickel bearing concentrates, cobaltite [CoAsS] concentrate from Blackbird Mine, Idaho, and siegenite [(Ni,Co)3S4] concentrate from Missouri Lead-Belt. The major strength of the system was the selectivity of extraction toward nickel and cobalt from iron containing solutions. Other metals such as Mn, Mg, Ca, Al and As were not extracted. Due to the irreversibility of copper extraction, its removal from solution was required prior to the extraction of nickel and cobalt. Zinc was not as strongly extracted (i.e. its stripping was readily achieved) as was copper . Flowsheets for the recovery of nickel and cobalt were also developed.

Jan 1, 1997

By H. B. Brunot

On April 26, 1949, the Bureau first approved a machine designed to replace the cycle of cutting, blasting, and loading coal by a single operation. This machine took the coal directly from the solid face and delivered it to transportation equipment. By January 1, 1955, 30 approvals for designs of machines of this type had been granted by the Bureau. In the main, this paper describes briefly the action of the various designs approved as permissible. In addition, the approval number, the date of approval, the voltage of the power supply, the number and character of the explosion-proof accessory parts, the size of the trailing cable, and the overcurrent protection at the outby end of the trailing cable are given for each design. Since no similar information has been published by the Bureau, it is hoped the material in this paper will be valuable in giving the mining public an organized look at the various machines of this nature that have been approved as permissible by the Bureau.

Jan 1, 1956

By M. A. Mahtab

This report presents the geometric parameters (attitude, spacing, extent, and aperture) of fracture patterns in a selected portion (study area) of San Manuel copper mine, Arizona. The geometric parameters are quantified for input to structural analyses for studies of the influence of fractures on cavability of ores. Using an orientation analysis procedure developed earlier by the Bureau, three prominent and nearly orthogonal sets of fracture orientations were delineated in the study area. Sets 1 and 2 dip nearly vertically, and generally strike east-west and north-south, respectively, whereas set 3 is nearly horizontal. Both a horizontal rotation (of 14° to 26° for sets 1 and 2, respectively) and a tilt (of 20° for set 3) is shown to occur between the 1415 and 2015 levels of the mine. Gomparison of the three major rock types present in the study area (quartz monzonite, monzonite porphyry, and rhyolite) show that the rhyolite is characterized by short extent, small spacing, and tightness of fractures as well as the general absence of fracture set 3, which may account for its generally observed strong resistance to caving.

Jan 1, 1973

By Fabio Da Costa Garcia Filho

Durante os processos de beneficiamento de alumina, no processo Bayer, é gerado um resíduo insolúvel denominado lama vermelha. A incorporação de resíduos industriais em cerâmica vem sendo utilizada atualmente na busca de matérias-primas alternativas, e também buscando uma destinação ambientalmente correta aos resíduos que poluem. O objetivo deste trabalho foi utilizar planejamento experimental para estudar a absorção de água em cerâmica incorporada com lama vermelha. Foram tomados pontos experimentais, cujos teores dos materiais utilizados variaram de 0 a 100%, e as formulações queimadas a 950°C. A argila verde e as misturas contendo maiores percentuais da mesma apresentaram menores valores de absorção de água e retração linear de queima. O modelo matemático que mais se ajustou foi o cúbico especial. Os resultados obtidos no planejamento de misturas mostram que para as três regiões experimentais propostas, o modelo cúbico especial foi o que mais se ajustou aos resultados reais, e que este é estatisticamente o melhor modelo matemático e deve ser usado para avaliar a absorção de água.

Oct 30, 2017

By I. Peerawattuk

Growing demand for Li-based battery technologies is leading to an unprecedented growth in the lithium industry. Although innovation in battery technologies has pushed lithium into the spotlight, lithium was not always known for its application in batteries. The primary use of lithium—prior to the introduction of commercial lithium-ion batteries in the early 2000s—was in the ceramics, glass, grease, and the medical industry. Before being converted into usable forms, lithium products must be upgraded from the raw material. Processes for recovering lithium may involve: thermal treatment, water leaching, solar evaporation, ion exchange, carbonation, and electrodialysis. Presented, is a historical review of lithium applications and the different techniques of converting lithium-rich minerals and brines into usable products with additional discussion on future lithium extraction processes.

By Santiago Faucher

Molten slag from pyrometallurgical furnaces is tapped at high temperature, carrying a large amount of thermal energy. But the common slag dumping and water granulation methods used for slag treatment do not permit energy recovery. Furthermore, water is present in these processes and while operations are designed to minimize risks of steam explosions, from the contact of slag with water, these common slag handling practices have never been inherently safe. Common handling practices do permit some slags to be sold, but often in low volumes at low prices. Dry granulation offers advantages over these common slag handling practices, including the production of by-products, the recovery of thermal energy, and the eliminated consumption and safety hazards of water. For these reasons, there have been various studies in dry granulation and heat recovery, but most have never been brought to commercial scale due to scalability and cost challenges. Ecomaister- Hatch has developed and brought to commercial scale a reliable and simple dry granulation and heat recovery technology. Here we review common slag handling practices, the developments in dry slag granulation over the last three decades, introduce the Ecomaister-Hatch dry slag granulation process, and elaborate on future applications of the technology in the processing of argon oxygen decarburization and blast furnace slags.

Aug 17, 2017