Search Documents

By José Arango

La Planta Hidrometalúrgica de Cerro Verde tiene como objetivo alcanzar la máxima calidad en cada uno de sus procesos operativos. Para ello, desarrolla un diseño que permita la transformación del control remoto a una operación automática, generando decisiones lógicas. En ese sentido, el presente texto señala la importancia de los Sistemas de información de operaciones en el sistema de automatización de Cerro Verde - en tanto es soporte de la implementación de un completo sistema de instrumentación y de la instalación de una red de PLC’s que colectan la información y en base a esta, desarrollan una lógica de operación manteniendo interconectados todos los circuitos operativos. Posteriormente, con el uso de software se crea una interfase de conexión entre la red industrial y la red Administrativa, permitiendo adjuntar la información en una base de datos que junto a la otra base administrativa, constituyen un ERP que da vitalidad a nuestra operación. De forma que los sistemas de informacion instalados en Cerro Verde consideran a los sistemas de instrumentación como los ojos del operador de planta.

Jul 17, 2000

By N. P. Kripakov

Results of a complex three-seam interaction analysis in a western U.S. coal mine are presented. The physical situation simulated by the models represents the development of a set of entries underneath two previously mined seams with all three seams in proximity to each other. The layout and the geometry of the remnant pillars in the upper seams were nonuniform and not always directly superimposed over each other, creating a very challenging modeling problem. The U.S. Bureau of Mines' MULSIM/PC computer code was upgraded and enhanced to perform the required three-seam interaction calculations. Analysis was limited to simple linear-elastic assumptions as only peak stresses were required. Results clearly indicated that stress concentrations in the lower seam increased approximately 100 percent when compared to cases simulating no extraction in the two upper seams. These stress concentrations generally occurred in zones directly below points of highest abutment pressures in the upper seams. Overall, the model results compared favorably with actual documented observed behavior where roof failures were known to have occurred.

Jan 1, 1996

By A. T. Iannacchione

Recent fatal injuries occurring during pillar retreat coal mining call for better identification of the hazards and recognition of risks. Ground control hazards associated with room-and-pillar retreat mining tend to intensify with depth, requiring extra precautions in the form of additional controls. In many locations these activities are further complicated by local complexities often associated with unique or novel circumstances, such as over-mining or under-mining. One technique recently studied by NIOSH, Major Hazard Risk Assessment (MHRA), may help mine operators to mitigate the risks associated with pillar recovery operations. The approach was trialed at two underground coal mines in southern West Virginia that are currently practicing pillar recovery. The first step in the MHRA process involved reviewing the segments or parts of the pillar extraction mining system and identifying associated hazards and threats to the operation. Some of the high risk hazards at these two sites included: ? Rock fall during pillar extraction covers equipment and injury ? occurs during recovery operations, Rock fall above the roof bolt horizon, potentially injuring ? workers and/or requiring recovery action,Rib fall under deep cover, potentially injuring workers, and; ? Strata instabilities associated with subsidence of the ? interburden due to simultaneously mining two seams in close vertical proximity to one another. The mines? risk assessment teams then considered each threat individually in order to systematically identify potential unwanted events. The top unwanted events were examined individually using structured risk analysis tools. The output from the process includes a list of priority existing controls for monitoring and auditing, and a second list of potential new controls. These controls consisted of: ? Examples of best practices, ? Enhanced communication, ? Implementing standard operating procedures (SOP), ? Protocols for emergency response actions, ? Effective layouts, ? Efficient monitoring, and; ? Successful audits. This paper documents the process as it unfolded at the two mines, and analyzes the strengths and weaknesses of the MHRA technique as it applies to pillar recovery operations. This work was part of a larger NIOSH research project. NIOSH was responsible for: 1) facilitating the risk assessment process known as Major Hazard Risk Assessment (MHRA), 2) documenting the risk assessment process, and 3) providing mine management with a written draft summary of the risk assessment process. The results of the risk assessment represent the thoughts and opinions of the individual risk assessment teams and should in no way be construed as an endorsement of the risk assessment output by NIOSH or the University of Pittsburgh.

Jan 1, 2009

By Bengt Fellenius

The conventional wave equation analysis without control of the representativeness of the parameters to the actual conditions does not provide accurate results. However, the representatives can be vastly improved by means of using the results of monitoring the dynamic response in a pile during driving. Dynamic monitoring displays the interaction of independent strain and acceleration measurements having directly propor­tional response to impacts, but inversely proportional response to re­flections from the soil. Examples are given and the CAPWAP method used to calculate from the measurements the dynamic pile and soil para­meters and mobilized soil resistance is outlined. The dynamic monitoring technique and analysis has been accepted internationally and been incor­porated into Building Codes. The prediction is offered that in five year's time, no major piling project will be undertaken without dynamic monitoring and analysis.

Jan 1, 1984

By Dennis Van Heerden

Southern Africa has a long history of underground hard rock mining dating back to the late 1800?s. The rock support of underground excavations has significantly changed during this period, due to improved technology, experience gained and rock support requirements by mining and geotechnical engineers. This paper examines the available underground rock support methods in Southern Africa with emphasis on the types and characteristics of: - Rock bolt types. - Rock bolt and long anchor grouts. - Thin-sprayed liners. - Sprayed Concrete. - Ground consolidations through injection methods. - Cavity and void filling with aerated cement products. [ ]

Jan 1, 2007

Various steps, and complete sequences, for the recovery of lead and zinc from a mixed sulphide concentrate, high in silica and pyrite, have been tested.Oxidation steps of roasting in air or in a sulphating atmosphere and use of aqueous acidic, ammoniacal, and near neutral oxidation media were compared. Oxidation roasting or use of acidic media appeared most useful. Procedures for dissolution of zinc from calcines using sulphuric and sulphurous acid to avoid silica gelation problems are compared and a direct leaching procedure with sulphuric 'acid at controlled pH shown to be the most useful.Methods for the removal of germanium, nickel, and magnesium from zinc sulphate solutions prior to zinc electrodeposition were tested. The recoveries of zinc from ammoniacal solutions by electrolysis and distillation are compared.The dissolution of lead compounds from the residue of zinc extraction by amine and ammoniacal ammonium sulphate (AAS) solutions Was tested. Lead, sulphide was precipitated in filtera'ble form from AAS solutions. The reduction of lead sulphate to lead sulphide with sulphur was difficult, but possible. The various steps were used to deveiop five complete processing sequences, of which two were shown to be technically feasible and have potential economic viability.

Jan 1, 1975

NASA has received direction for lunar habitation beginning in 2024. Prior to then, it will be necessary to learn about how lunar soil can be used to promote civilization on the moon. Questions must be answered: ?Will it support plant life?,? ?Can it be used as a construction material?,? ?What is needed to maximize health and safety?,? and ?Will it affect equipment, tools, machinery, and clothes?? The only samples available for study came from the Apollo Missions. Because the expense of bringing more material back to Earth is prohibitive, there is not enough available to perform studies to answer the above questions. Hence, there is a great need for its synthesis. Most efforts to date have concentrated on making ?simulant? from single natural resources of volcanic rock. However, another possibility is to use resources here on Earth to extract the minerals of interest into concentrates or so-called ?separates? using traditional mineral processing techniques, and then mix the separates in appropriate ratios to simulate the lunar soil. In this paper, results from a study in which dry Road Norite outcrop and wet mill tailings from the Stillwater Mining Company?s Concentrator located near Nye, MT were examined. Of course, the in-side challenge is to make ?separates? from gangue minerals.

Jan 1, 2012

By Larry Rayburn

In the spring of 1999, construction commenced on the new Steelers Football Stadium in downtown Pittsburgh, Pennsylvania. Richard Goettle, Inc. (RGI) was the successful bidder to install the specified augercast piles for the foundation package. Description - Pittsburgh Steelers Stadium The new stadium will house the Pittsburgh Steelers Professional Football Team. It is widely believed that if a team is provided with a modern playing facility, that a winning season will ensue (Not always the case). The new stadium location is on the north side of Pittsburgh on the Ohio River, and just downstream of the confluence of the Monongahela and Allegheny Rivers. The site is west of existing Three Rivers Stadium. The Three Rivers Stadium was built during the late sixties and housed both the Pirates Baseball and Steelers Football Teams. The Public Auditorium Authority elected to replace this outdated stadium with two new stadiums, one for each professional team. The landmark stadium was imploded in February of 2001.

Jan 1, 2001

When xanthates or dithiophosphates are used as collectors in sulphide ore flotation, adsorbed species may be identified by gas chromatography of the volatile products formed during low temperature pyrolysis. For collector additions ,as low as 20 g/tonne of ore, pyrolysis of the flotation products usually gives' an olefin directly related to the particular xanthate or Aerofloat reagent used. The method is able to provide valuable qualitative and quantitative data relating to the extent of collector adsorption and the resulting changes in the hydrophilic or hydrophobic nature of the mineral surface.

Jan 1, 1974

At Copper Refineries Pty. Ltd., Townsville, two reverberatory furnaces of 420 tonnes capacity are used to melt 210000 tonnes/year of copper for subsequent anode casting. When the refinery commenced production in1959, these furnaces were of 300 tonnes capacity. The original furnaces featured a silica brick hearth, magnesite and chrome magnesite side 'walls, and a sprung silica brick roof, but were unsatisfactory because of thelow refractory life and high costs. With continuous expansion in production and the incentive to increase furnace life and capacity the design of these furnaces has changed greatly since that time.The present furnaces feature all basic brick, a flat suspended basic brick roof, very extensive use of watercooled copper sections, and are of substantially increased (420 tonnes) capacity. Particular attention has been concentrated on high wear areas such as the taphole, side walls, and charging door jambs. Each furnace in its 24 h cycle, is charged, the copper melted, impurities skimmed off, metal "poled" prior to casting, and cast.The service condition during each of these operations is important in considering furnace refractory life.The improvements in operating practices and furnace 'construction which enabled the capacity of the furnaces to be increased are discussed. The life between major repairs to side walls has increased from 90 charges to300 charges.The scope for future improvement is considered and areas for development are suggested.

Jan 1, 1977

By B S. Utting, W J. Cowie

The alluvial gold industry of New Zealand is based on the placer deposits in Otago and on the West Coast. Production from these since discovery in the 1850s has been an estimated 480 t (15 Moz) of gold. Annual output has expanded continuously since 1980 and is expected to be over 2 t of gold for 1989. Following a historical review, the characteristics of typical operations, which use hydraulic excavators and mobile trommel units are discussed. Descriptions are then given of alluvial activities in Otago and on the West Coast.

Jan 1, 1990

By S. H. Lorain

This paper is a preliminary report on recent lode gold mining activity, operating conditions, and mining and milling methods at properties in production in September 1936 in the gold belt of northeastern Oregon. A few inactive properties are described also. Districts, inactive in 1936, that have been important producers at some time in the past are mentioned briefly. This is one of a series of similar papers describing western mining districts. The past production record of the gold mines of northeastern Oregon entitles the region to be ranked as one of the important gold-mining regions of the United States. Although comparatively inactive for many years, lode mining in the region has recently undergone a marked revival.

Jan 1, 1938

By William H. Langer

Large amounts of limestone fines co-produced during the processing of crushed lime-stone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point sources such as cement manufacturing. AWL reactants are readily available, inexpensive and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid. This reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities to within about 10 km (6 miles) of the coastline. The majority of U.S. coastal power-generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufacturers and research scientists. There is a concern that CO2 generated from human activities is contributing to climatic and environmental changes. Approximately one-third of anthropogenic CO2 emissions come from burning fossil fuels to generate electricity. Each power plant is capable of emitting several million tons of CO2 annually. A variety of other industrial processes, such as cement manufacture, oil refining, and iron and steel production, also emit large amounts of CO2. The level of atmospheric CO2 can be reduced by capturing CO2 from point-source emissions and storing or sequestering it in isolation from the atmosphere (U.S. Department of Energy, 2003). In 1999, G.H. Rau and K. Caldeira proposed a geochemistry-based method that is referred to as accelerated weathering of limestone (AWL) in a paper titled ?Accelerating carbonate dissolution to sequester carbon dioxide in the ocean ? geochemical implications.?

Jan 1, 2009

By Terry P. Medhurst, Stuart A. MacGregor, Peter J. Hatherly

In addition to fractures and joints, compositional factors and bedding influence the strength of clastic sedimentary rocks. Rock mass rating schemes must therefore consider all of these factors. In this paper, a rating scheme for clastic sediments based on geophysical measurements is described. Geo-physical logging allows an approximation of rock com-position to be obtained and an assessment of bedding frequency and laminations. Velocity measurements incorporate the effects of fracturing. The rating requires scores for the intact rock, bedding/cohesion, and defects. These are combined to yield a Geophysical Strata Rating (GSR). Determination of the GSR is objective and repeatable. GSR values are typically between 20 and 80 and can be related to the Coal Mine Roof Rating.

Jan 5, 2007

By Jennifer Riefenberg

Ground control hazards, coal quality, ore reserve estimation, and pollution modeling seem unrelated topics from most mining perspectives. However, geostatistical methods can be used to characterize each of these, and more topics. Exploratory drill core data, and continued drilling and field measurements, can provide a wealth of information related to each of the above areas and are often severely underutilized. Recent studies have led to the development of the Multiple Parameter Mapping (MPM) technology, which utilizes geostatistics and other numerical modeling methods, to generate a "hazard index" map, often from exploratory drill core data. This mapping has been presented for ground control hazards relating roof quality, floor quality, numerically modelled stresses due to mining geometry, and geologic features. A review of the MPM method, future directions with the MPM, and a discussion of using these and other geostatistical methods to quantify coal quality, ore reserve estimation, and pollutant modeling are presented in this paper.

Jan 1, 1996

Beatrix Gold Mine, a deep-level gold mine in the Free State province of South Africa, has the highest methane emission rate of any gold mine in the country. Methane is emitted from underground sources intersected during mining operations and is liberated into the general mine atmosphere. The total methane emission rate for the mine is of the order of 16001/s and the South section of the mine emits approximately 10001/s of methane gas. The mine has a history of gas accumulations which have led to a number of underground explosions. Following the last explosion in 2001 and the subsequent investigation, a number of recommendations were made. Two of these were to consider extracting the underground mine methane to render the mine atmosphere safe, and to declare hazardous locations that require special operating procedures. A number of such workplaces have now been declared at the South section of the mine. Methane gas is a potent, explosive greenhouse gas whose contribution to global warming and climate change is 21 times higher than that of carbon dioxide. To reduce its inherent danger and to mitigate its global warming impact, a carbon credit project under the Clean Development Mechanism (CDM) of the Kyoto Protocol has been developed and implemented, the aim being to capture and destroy the methane at Beatrix mine. The mine has constructed an extraction system to capture and extract 400 (Is of the methane. Percentage methane (per volume) of the gas intersected at source is 85%, with negligible concentrations of other hydrocarbons and water associated. The mine contracted the services of Group Five to design and construct the flare and ancillary equipment on surface, and Promethium Carbon was contracted to assist with the carbon¬-related aspects, approval framework, and administration of the project. A number of design and construction challenges had to be faced to extract and transport the gas effectively to the surface of the mine as the emitters are approximately 3 600 m away from the mine shaft at a depth of 860 m. Further considerations were the requirements for the type of column to be used to transport the methane gas, the pressure loss over the system, the safety systems needed to address the risk factors involved in the transport of the methane gas, and a suitable pumping system to extract the gas to the surface. The system operates under negative pressure provided by two blowers on surface delivering the emissions to a flare capable of burning off 450 8/s of methane gas. In this paper a number of benefits for the mine are discussed. These include, but are not limited to, the removal of approximately 55% of the total volume of methane gas from the general body of the air in the geographical areas of the mine where the methane gas is emitted into the atmosphere, and reducing the risk of methane-related incidents. A further benefit of this project is the mitigation of the global warming impact of the methane gas and the reduction of the mine's carbon footprint by approximately 25%. This project could also assist in alleviating the energy shortage being experienced in South Africa by means of the planned generation of 4 MW of electrical power, utilizing the methane gas, as a second phase of the project.

Jan 1, 2011

TIMBER supports for large underground cavities are temporary expedients until the permanent filling can be put in. Nevertheless, timber supports are very necessary in some form. The general problem is to support the cavity in all directions withthe minimum of timber, disposed in the strongest way. The simplest way of filling an irregular space with timber sets is to form triangles.The right-angled isosceles triangle (Fig. 1) leads to the true square set, in which caps are equal to struts. The right-angled unequal-sided triangle and the scalene isosceles triangle (Fig. 2) lead to the oblong square set, where caps are longer than struts.The scalene triangle (Fig. 4) leads to the rhombic or oblique set. The equilateral triangle leads to the hexagon set (Fig. 3), in which the caps and struts are all equal. These five plane figures, the triangle, square, rectangle, rhomb and hexagon, are the only figures that will completely fill any irregular plane figure, without interstices. Hexagon sets were first suggested by the writer in 1902 to a mine manager at Broken Hill, who did not see his way to use them.

Jan 1, 1912

By L. D. Gent

This report reviews the current state of the art of remote control techniques for underground continuous miners. A delineation of aspects requiring additional data is presented. Also a summary and delineation are presented in overview form for the related section functions: roof control, haulage, ventilation, power supply and rock dusting. The automated remotely controlled continuous miner project is a long-range research effort. However, the program has been divided into intermediate steps resulting in incremental production increases throughout the program. Data are developed relating the impact of our proposed research and development accomplishments to potential productivity impact.

Jan 1, 1975

By F. L. Pirkle

A heavy-mineral deposit about 1.6 kilometers (I mile) in length and averaging about three meters (10 feet) in thickness is exposed approximately130 kilometers (80 miles) east of Denver, along Interstate 70, in Elbert County, Colorado near the town of Limon. The deposit is exposed in a geomorphic feature known locally as Titanium Ridge. The dominant heavy minerals, accounting for about 70% of the total heavy mineral suite by weight, are ilmenite, garnet, and zircon. The mineralized zone appears in a series of visually interpretable facies that are stacked vertically and represent subtidal, forebeach, backbeach, washover fan, and aeolian depositional environments. These paleoenvironments are analogous to depositional environments represented by a modern heavy-mineral bearing facies tract on St. Catherines Island, Georgia. Thus, Titanium Ridge provides evidence that heavy-mineral accumulation models for late Cenozoic deposits in the Georgia and Florida coastal plains are applicable to heavy-mineral deposits of the Western Interior subsurface and, by implication, the Western Interior Seaway, extending from Mexico to the Canadian Arctic.

Jan 1, 2011

By D. D. Munro

Finsch Mine is a kimberlite diamond mine located at Lime Acres in the Northern Cape Province of South Africa. The mine was founded in 1961 and started surface mining in 1964. Underground production commenced in 1990 using a modified blast-hole open stoping method for the mining of Blocks 1, 2 and 3. Block 4 is currently being mined as a block cave. The process of identifying and optimizing a method to mine the Block 5 orebody started in 1991, and in 2006 incline caving was identified as being technically feasible. This paper aims to document the process employed in developing this method by the Block 5 prefeasibility team as well as discuss the technical challenges encountered during this process. The paper commences with a history of Finsch Mine and highlights the complex geology and threat of sidewall failure that prompted the decision to use block caving as the mining method for Block 4. A literature study of mines that implemented mining methods upon which the incline cave was conceptualized is then presented. These practices were then used to form the basis for the designs on which the initial geotechnical modelling was done and built upon through an iterative process of modelling and design changes. The ventilation of the mining area, initial productivity simulation results, and the applicability of automation and comminution processes in the incline cave are also presented. The paper concludes with an investigation into some of the challenges of the mining method, and shows that that incline caving is a technical option available for further investigation in determining the optimal mining method to be employed at Block 5, Finsch Diamond Mine. Keywords massive mining, incline caving, geotechnical modelling.

Jul 1, 2013