Search Documents

By S. Dereski, G. Chancellor

"INTRODUCTION Barrick Goldstrike underground mine is located in Northern Nevada on the Carlin trend. The underground mine produces approximately 1.5 to 1.8 million tons a year and approximately 400,000 ounces of gold a year. The mine is comprised of two main mining methods, underhand drift and fill and long hole stopeing. The mass blast project stated in 2012 as Value in Use project between Barrick, Southwest Energy and Orica, the goal of this project is to be able to blast an entire drilled stope in one blasting event instead of taking multiple blasts. This will improve productivity by eliminating intermediate blasts, reducing additional blast time, eliminate drill hole cleaning due to the previous blast. Project implantation started in the fourth quarter of 2013 and mass blasting has been common practice throughout all of 2014. STOPPING PRACTICE AT GOLDSTRIKE BEFORE MASS BLAST PROJECT The production from the Goldstrike mine is approximately 70% from stopes. The timely completion of all stoping blocks is imperative to maintaining the plan, delays in the execution of any particular block can have detrimental ripple down effects as neighbouring stoping blocks become delayed. Before the implementation of this project the standard practice for Goldstrike was to: 1. Drill the entire stope 2. Blast a bottom shot, normally between 10 feet and 20 feet off the bottom of the slot rings. This would be mucked out before the next shot 3. Blast a pull through shot, this included the raise and one or two production rings. Again mucking this out before the next shot 4. Blast production rings, one or two more blasts depending on stope size. In most cases between each of these blasts the holes in the other rings of the stope would have to be cleaned. This meant either cleaning manually using air and water, or mechanically cleaning with a bench drill. In many cases this resulted in delays in completing the stoping block."

Jan 1, 2015

By Takeshi Nagano

"Prior to discussing future trends of non-ferrous metals smelting and refining, the past developments are looked back. Social and economic environments in Japan over the past two decades are reviewed. Technological developments to comply with these environments are explained, taking for examples the cases of the Mitsubishi continuous smelting and converting process and Onahama's jumbo tank system for copper tankhouse. After considering the factors which will influence the improvements in non-ferrous processing, future trends are forecasted generally for copper, zinc, lead, aluminum and rare earth metals. Recent development works in Japan for the future are also introduced. In the discussed area, it appears that the emergence of new innovative processes would be difficult. The progress will be made rather toward the sophistication of the existing technologies, utilizing the advancement of the related technologies such as computers, electronics, etc. IntroductionThis paper discusses the future trends of non-ferrous metals smelting and refining on the occasion of the international symposium, ""The Metallurgical Processes for the Year 2000 and Beyond"".It is considered that the improvement of technology is greatly influenced by the social and economic environments which surround it. From this standpoint, review was made of Japanese case over the past two decades. Various new technologies were developed also in the non-ferrous metal world to comply with the requirements under the above environments. The examples are described in the cases of the Mitsubishi continuous smelting and converting process and Onahama's jumbo tank system for copper electro-refining.After foreseeing the major factors which will affect the technological developments in the future, the trends are forecasted for copper, zinc, lead, aluminum and rare earth metals generally. Some development works in Japan, which will give suggestions for future trends, are also introduced in some detail."

Jan 1, 1988

By C. G. Anderson

The treatment of concentrates for the recovery of the precious metals imposes many processing and environmental challenges. Hydrometallurgical technology for recovery of values from refractory precious metal materials has been developed at Sunshine Mining and Refining Company. Historically, conventional pyrometallurgical methods have been used for to recover values from refractory precious metal materials. However, enhanced environmental awareness has worked to constrain typical refractory material processing methods. This hinders and limits the ability of established smelting or roasting technologies to fill the needs of new sources of refractory materials. An alternative is to treat refractory precious metal bearing materials by hydro metallurgical techniques. These methods are considered more environmentally appropriate since they do not produce gaseous pollutants like sulfur dioxide. Industrially, Sunshine Mining and Refining Company employs hydrometallurgical technology to process refractory precious metal materials. The Sunshine antimony leach uses a mixture of sulfur and caustic under ambient pressure and boiling conditions. The Sunshine oxidation leach uses a mixture of sulfuric acid and a minimal amount of sodium nitrite under relatively mild oxygen pressure and temperature conditions. These conditions result in a nitrogen species catalyzed sulfuric acid pressure leach. Since hydrometallurgical technologies provide industrially proven processing options for many types of refractory precious metal containing materials, their usage should be considered. Ample work has been conducted to prove the effectiveness of Sunshine refractory processing technologies on various materials. This has included platinum group metal materials, refractory gold concentrates, silver materials and indium materials. In some cases, complete process flowsheets have been designed to recover both base and precious metals from these materials and to treat the generated waste streams in environmentally sound manners.

Jan 1, 1996

By R. Thorpe, M. Dosbaba, A. Kopriva, A. Niiranen, J. Ruokanen

"Automated Mineralogy (AM) is an important diagnostic tool in flotation plants as it adds ore and particle mineralogical properties to traditional mass and chemical data. AM is used in project development, for future ore studies and for diagnosing concentrator operations. With the exception of operations who own central laboratory or on-site systems, the use of AM is often limited to the analysis of a comparatively small set of samples. Metrix Plant Technologies has partnered with TESCAN to integrate TIMA AM technology into the implementation of Performance Assessment Campaigns (PAC). Routine daily composite samples from the mill are analysed mineralogically on a size-by-size basis over several weeks. All the relevant metallurgical, process control and mineralogical data is combined into a single large database for mass balancing and interactive examination. This paper describes the implementation and results of a PAC at the Agnico Eagle Kittilä gold mine in Finland. Although challenging, the addition of mineralogical data as dependent variables in multivariate analysis leads to a much deeper understanding of the root cause effect of events driving the flotation performance. INTRODUCTION TO STUDY The Kittilä mine, owned by Agnico Eagle, is Europe’s largest primary gold mine, with annual production of approximately 180,000 Oz. The operation is located in Lapland in northern Finland, and is currently expected to operate until 2035. The location of the operation is shown in Figure 1. Historically, the mine was an open pit, although in recent years ore is sourced solely from underground operations. The processing plant features crushing and grinding, followed by carbon flotation and sulphide flotation. Carbon concentrate is a waste stream, and sulphide concentrate reports to pressure oxidation (autoclave) and CIL circuits for gold extraction. The final flowsheet is shown in Figure 2. Following commissioning in late 2008, the operation achieved commercial production on May 1st 2009. Gold recovery in flotation gradually increased to a 92-96% range at a throughput of ~3500-4000 tonnes per day. In late 2014, the operation commissioned a plant expansion to ~5000 tonnes per day. Following a commissioning period, the operation stabilised with recoveries in a 90-94% range, which over any given period was determined to be ~2% lower with statistical significance. The trends from start-up of gold recovery in flotation and throughput are shown as follows in Figure 3. In early 2016, Agnico Eagle Kittilä mine, along with Agnico Eagle Technical Services (AETS) partnered with Metrix Plant Technologies and TESCAN, to perform a Performance Assessment Campaign (PAC) at Kittilä, involving automated mineralogy on five key streams at Kittilä on 40 days selected from a 50 day period between February 15th and April 4th 2016, when plant operations were stable. In addition to the mineralogical data, metallurgical and operational data were pooled into a single, powerful database to explore opportunities for the operation to improve recovery in a sustained manner, ideally to the levels pre-expansion."

Jan 1, 2017

By D E. Thorp

The mining and concentration operations of New Zealand Steel have been carried out initially from the Waikato North Head (WNH) deposit since 1969 and subsequently from the Taharoa deposit since 1972. Over the years the WNH operation has produced about 1.2 million tonnes of concentrate which has been converted into steel, while total exports to the Japanese Steel Industry from Taharoa reached five million tonnes in February of this year. Recent expansion plans both in domestic steel production and in the ironsand concentrate export market have made it necessary for the company to look closely at, among other areas, the mineral processing of the titaniferous ironsands in both deposits. This paper deals with the recent test work carried out at WNH and Taharoa on the use of the cone concentrator unit as a primary gravity concentrating unit ahead of the magnetic separation stages and as a cleaner concentrator following the primary magnetic separation.

Jan 1, 1977

By Nicolas Moscoso, Gerald Verbeek, Marcel Bielefeld, Rob van Dorp

Upon recently, most offshore foundations were based on a number of driven piles that were installed with an impact hammer. With the increase in offshore windfarms two major developments have occurred: the shift from jackets to monopiles, leading to increase of the diameter of the foundation piles, and a shift from impact hammers to vibro hammers. As the use of vibratory hammers is becoming more and more common practice, the need for accurate vibro-driving simulation software has increased, which requires that the soil modelling is enhanced to address soil fatigue during pile driving and to predict reliably the soil behavior and resistance during pile driving. In addition pile driving monitoring, which is routine for piles driven with an impact hammer, needs to become common practice. This paper addresses advances in soil modelling that allows more accurate pile driving simulation as well as the application of Vibro Driving Analysis (VDA) or Monitoring (VDM) to validate the simulation results. This is illustrated by a case study of the test pile for the Delft Offshore Turbine project, a 28 m long monopile with a diameter of 4 m that was driven 15 m into dense sand layers using a vibro hammer. After some 6 months the pile was extracted, and pile driving simulations and VDA were done both for the installation and extraction phase. 1. INTRODUCTION At the end of 2017, the total worldwide offshore wind power capacity was 18.8 GW [1]. The vast majority of offshore wind farms are currently in Northern Europe, which together account for over two thirds of the total offshore wind power installed worldwide, followed by East Asia, while developments in North America are still in very early stages.

Jan 1, 2019

By V. Kecojevic

Environmental and economic costs related to equipment fuel consumption and carbon dioxide (CO2) emission present a substantial challenge to the mining industry. Haul trucks are an integral part of the overall surface mining system and they consume a significant quantity of fuel. Consequently, they produce a significant amount of CO2. The objective of this research is to (i) establish a mathematical relationship among a truck?s fuel consumption, power and engine load factors and (ii) determine the amount of a truck?s CO2 emission and the associated cost that may arise from potential CO2 legislation. In order to achieve these objectives, the authors have considered original equipment manufacturer (OEM) haul trucks, which are commonly used in surface mining operations. The research presented here may be used by mining professionals to help determine the cost and environmental burden of the trucks? application and efficiently manage energy consumption.

Jan 1, 2010

By King D, Dickinson S. B, Matheson R. S

Commencing in 1956, Rio TInto Australian Exploration Pty Limited in association with Electrolytic Zinc Co of Australasia, Limited, has been carrying out a mineral prospecting program in North-West Tasmania over an area of about 4000 square miles.The program has comprised extensive airborne geophysical surveys, detailed geological mapping, ground geophysical and geochemical investigations. Out of the wealth of new data, and the examination of previous records, has emerged a new structural concept of regional ore control and distribution in North-West Tasmania. This roncept stems from the discovery of an ancient 'fossil' rift valley (graben), named the Owen Rift Valley, along which are located the major mines of the area and numerous well-known prospects. The known mines and prospects from north to south include Mt Bischoff (tin); the Pinnacles (zinc, lead, ropper); the Chester (pyrites); Rosebery-Hercules (lead, zinc, ropper, silver, gold); Mt Tyndall (lead, ropper, zinc); Comstock and Tasman (copper, lead, zinc); Mt Lyell (copper, pyrites, gold); Mt Jukes and Mt Darwin (ropper). The identification of the West Coast (Owen Conglomerate) Range as a fossil rift valley is due to Or B Campana, who carried out extensive geological mapping and interpretation work, and who, with S B Dickinson, are the senior authors of this paper.S B Dickinson, who introduced B Campana to the geological problems of West Tasmania, had previously investigated the Mt Lyell and Rosebery mining fIeld, to which reference is made in this work.D King assisted in the regional mapping and in providing numerous data on the mineral distribution of the area.R S Matheson rontributed to the fmdings on ore emplacement and rontrol in the discussions held on this subject. They are accordingly included as joint authors of this paper.Credit is also due to E McCarthy, who interpreted the geophysical results, and to J H Rattigan, who compiled the preliminary geological maps from published documents and by photo-geological methods.G Hall and V H Cottle, of the Electrolytic Zinc Co in Rosebery, provided invaluable geological data and suggestions in the course of the survey, and made a constructive criticism of the manuscript of this work. The airborne geophysical survey carried out by the Adastra-Hunting Geophysics Ltd company, furnished useful data which substantiated many of the fIndings on the stratigraphic and structural relationship. The Mines Department of Tasmania and S W Carey, Professor of Geology at the University of Tasmania, were instrumental in initiating the regional survey and provided the published and unpublished geological literature on the area.The authors also wish to acknowledge the invaluable assistance received from the Mt Lyell Mining and Railway Co in Queenstown, which made available the more recent geological and mining documents rompiled by M L Wade and M Solomon.

Jan 1, 1994

By Robert Snow, Shibo Zheng, Wenyi Song, Xiaoqing Ma, Patrick Zhang

Numerous phosphate mineral depressants have been reported in the literature for use during anionic flotation of dolomite from carbonate fluorapatite in slightly acid circuits. In one part of this research, laboratory flotation experiments were conducted to compare the effectiveness of phosphate depressants to process ground, deslimed high-MgO Florida phosphate pebbles. Ten potential phosphate depressants were evaluated during laboratory anionic flotation of dolomite from phosphate in a slightly acid circuit using a sulfonated oleic acid soap plus oil as the dolomite collector. Eight of the depressants have been used by various investigators with foreign and domestic carbonate-phosphate ores. Four of the depressants were found to be reasonably effective during the current flotation study, namely: sodium tripolyphosphate (STPP), sodium hexametaphosphate (SHMP), tetrasodium pyrophosphate (TSPP) and diphosphonic acid (DPA). Without depressants, the sulfonate collector required to produce cell underflow phosphate products containing <0.80% MgO and MgO/ P2O5 ratio <.033 was 1.13 kg/ton of flotation feed at a flotation pH range = 5.5-6.0. Using this collector level with 0.91 - 1.36 kg/ton of feed of STPP, SHMP or TSPP yielded phosphate products analyzing 0.73-0.92% MgO and MgO/ P2O5 ratios = .027-.034 at 90.0-96.8% P2O5 recovery. Similar grade phosphate products were obtained using DPA as the phosphate depressant at 84.1-87.5% P2O5 recovery. When no depressant was used, a similar grade phosphate product was obtained at only 65.9% P2O5 recovery. Another part of the research aimed at reducing MgO content in the final concentrate from Florida phosphate plants by conducting dolomite flotation on the final concentrate. Numerous phosphate depressants were tested for this purpose, including acidic, neutral and alkaline reagents. The most effective phosphate depressant was found to be phosphoric acid, giving both high grade and recovery.

Jan 1, 2014

By Bernard Porter

The solubility of UO2 was determined at 1,250° C. in ternary melts of UF4 and BaF2 with CaF2, LiF, and SrF2. The solubility of Ce02 was measured at 800° and 850° C. in a solution of CeF3, BaF2, and LiF. The amount of La203 which dissolves at 950° C. in a binary mixture of LiF and LaF3 and a ternary of LiF, LaF3, and BaF2 was also measured. In each case, the amount of soluble oxide was mound to be less than 5 weight-percent. A procedure was developed for filtering fused, oxide-saturated fluoride melts in order to obtain a representative sample for chemical analysis. The oxide content of the samples was determined by an inert-gas fusion procedure.

Jan 1, 1961

By Zenjiro Asaki, Teruo Tanabe

"To clarify the formation of light rare earth (R =Ce, Pr, Nd or Sm) -Fe compounds in the reduction-diffusion (RD) process, two kinds of experiments were carried out: (a) RD experiment in which briquettes composed of R oxide powder, Fe (particles or wire) and CaH2 were reacted, and (b) immersion experiment, where an Fe plate was immersed into R-Fe melt having the composition of Fe-side liquidus line in Fe crucible. The compound formation was examined by using XRD, SEM and EPMA. The formation rates of RzFe17 measured by the RD experiment were compared with those obtained by the immersion experiment. The growth rates of compounds obtained in the RD experiment for Pr-Fe and Nd-Fe systems were much lower than those obtained in the immersion experiment. This result was explained by the difference of the reduction rates of R oxides by Ca. The parabolic rate constants for the formation of RzFe17 were separated in two groups of (a) Pr-Fe and Nd-Fe systems and (b) Ce-Fe and Sm-Fe systems. This was discussed in connection with the difference of their crystal structures and the driving force of diffusion. The parabolic rate constants for the formation of compounds in Ce-Fe and Sm-Fe systems decreased in the order of RFez, RFe3 and RzFe17.IntroductionTo understand reaction behaviors in the production of rare earth (R) -iron intermetallic compounds, which have excellent magnetic properties, is very important from engineering point of view. And the reduction-diffusion (RD) process<O has recently attracted attention as one of the promising processes to economically produce R-related materials. A few fundamental studies on the compounds formation in the RD process have previously been reported. Qi, Hino and Yazawa(2) observed the formation of R(Nd, Sm)-Fe and R-Co compounds in the process from various view points. Song and Ogawa(3) measured the growth rates of Nd-Fe and Sm-Fe compounds by using Nd or Sm vapor supplied from Nd-Ca or Sm-Ca melts. The authors have also carried out fundamental studies (4)-(8) to clarify the rate and mechanism in the production of R-Fe intermetallic compounds."

Jan 1, 1998

By S. Geerts, J Davidson

The purpose of the experiment was to determine detonation characteristics of various improvised explosives. The test consisted of detonating a pipe filled with an explosive compound inside of a plywood arena. The pipe will be located in the center of the arena to ensure even distribution on the witness panels. Details on pipe dimensions, weights of the pipe and explosive, and the density were recorded prior to testing for use in the model calculations. The same size pipes were used throughout to minimize the variables inherent in testing. The plywood witness panels will capture the fragments so that penetration data was obtained, primarily the surface area of impact and depth of penetration. Through the use of the penetration data in conjunction with a mathematical model the original fragment velocity was determined. The mathematical model was developed to measure lethality of fragments from explosives and was modified to determine the original fragment velocity instead. From this model other variables such as the Gurney velocity were calculated. This test was done with an explosive compound that was commonly found, and numerous improvised compounds. In order to guarantee accurate data all of the explosives used for testing were cap sensitive, to eliminate the need for a booster charge which would introduce many unknown variables. The one common explosive compound that was used was C-4 which has known data in order to show accuracy of the model and calculations. The other 5 compounds chosen will not have this data as they will primarily be improvised mixtures.

Jan 1, 2011

By S. Uihteenmaki

Pyhasalmi is a massive sulfide orebody located in central Finland. The mine has been in operation since 1962. The flotation concentrator produces Cu, Zn, Pb and pyrite concentrates. The plant has used an on-stream analyzer for process control since 1968. The original analyzer has overlived a few generations of minicomputers, but the analytical parts are essentially unchanged. The on-stream analyzer is a critical component in plant process control system, which has made Pyhasaltni one of the pioneers in the art of computer control and optimization of flotation plants. The paper summarizes the experiences gained from the use of the high performance elemental analyzer system and the proven benefits from the use of on-stream analyzers at a complex sulfide flotation. The aging analyzer is approaching the end of its useful life. A new state of the art analyzer system is undergoing testing at Pyhasalmi.

Jan 1, 1999

By J. C. Barry, J. H. van Laar, P. L. Crouse, H. Bissett, I. J. van der Walt

"Plasma-assisted spheroidisation of metal powders offers several technical advantages with respect to both the ease of materials handling and powder-metallurgical item manufacturing. Advantages include improved flowability, increased powder packing density, elimination of internal component cavities and fractures, changes in morphology resulting in decreased friction between particles and contamination during pneumatic transport and enhanced particle purity. In this empirical study, spherical iron particles were produced using a microwave plasma operating at atmospheric pressure and characterized using optical microscopy and SEM techniques. Iron powders were fed into the system at fixed operating conditions, resulting in particles with spherical structures. The theoretical estimate of the time required for melting to occur is 1.6 ms, an order of magnitude smaller than the actual residence time. IntroductionParticle design and functionalization has become an increasingly popular aspect of materials synthesis and powder-metallurgical item manufacturing. One such technique involves the spheroidisation and densification of feed materials, typically in the form of chemical powders with wide particle size distributions. The major benefits of powder spheroidisation include improved powder flowability, increased powder packing density and powder purity, reductions in internal voids and defects, as well as the ability to manipulate the particles surface morphologies (Boulos, 2004). Thermal plasma processing has the potential for scale-up and for producing industrial quantities of spheroidised powder.Thermal plasma technologies offer a wide spectrum of material synthesis and treatment options, amongst others the synthesis and spheroidisation of nano-sized ceramic and metal particles (Kumar and Selvarajan, 2006). The spheroidisation process occurs within the plasma discharge via in-flight heating and melting of the powder feed material, given high enough plasma temperatures (Fridman, 2008, p. 495). Surface tension in the molten droplets results in spherical, or nearly, spherical, powder particles being formed upon exiting the plasma discharge where the droplet undergoes rapid cooling and freezes. Quite often, the bulk density of these spherical particles is higher than that of the starting material (Boulos, Fauchais and Pfender, 2013, p. 42). The different plasma spheroidisation techniques reported include radio frequency (RF) induction thermal plasmas (Jiang and Boulos, 2006; Karoly and Szepvolgyi, 2005; Yuming, Junjie and Yanwei, 2013), nontransferred direct current (DC) thermal plasmas (Chaturvedi et al., 2014; Kumar and Selvarajan, 2008; Suresh, Selvarajan and Vijay., 2008) and microwave-assisted plasma processing methods (Chen, Gleiman and Phillips, 2001; Vanamu et al., 2004; Weigle et al., 2004)"

Jan 1, 2016

By Akihiko Nishiyama

Unmanned construction technology used for remote control operation of construction machines has some problems to solve compared with manned operation of construction machines, such as fatigue due to long-term operation or decreases in operational efficiency. To solve these problems, we recorded the viewpoints of operators in both manned and remote control operation and analyzed the differences. This paper reports on our discussion of improving the operability of remote control operation based on the analysis results.

Aug 1, 2013

By S. Mondon

Hibi Smelter which is a Copper Smelter lining a blast furnace, produces 2,700 metric tons of anode copper per month. Generally, in a copper refinery, arsenic and antimony are considerably troublesome impurities. With regard to the elimination of antimony, Hibi Smelter has two handicaps described as follows. (1) Smelting under the slightly oxidizing atmosphere in the blast furnace. (2) Recycling the converter slag to the blast furnace after cooling. Therefore antimony and arsenic, mainly antimony, elimination tests, in which the alkaline flux was injected through the two tuyeres in the blowing stage, were carried out in the rotary anode furnace. Antimony and arsenic were respectively removed more than 90 96 from the molten copper, and their high eliminations are discussed by application of the transitory and permanent reaction model with the flux injection, which was presented by T. Lehner.

Jan 1, 1983

By R. G. B. Pickering

Successful management of mining operations depend on the accurate and reliable measurement of performance as a monitoring instrument in a feedback and control loop. However, when changes are being considered, the probable effect of the change on bottom line results requires different measuring techniques incorporating an in depth understanding which can identify hot spots in the operation which exhibit strong sensitivity to change. The CSIR&apos;s Division of Mining Technology has therefore been devoting a considerable effort to the establishment of techniques which enable changes to be analysed in terms of their impact on the two key parameters describing mine performance, i.e. profitability and safety. This paper describes these techniques, outlines their application to some example situations and discusses planned enhancements. The first section of the paper addresses the profitability model, and this is followed by a section considering the mine safety model.

Jan 1, 1996

By J. Kretschmann, O. Drusche, S. Krause

Mining companies are caught between the growing international relevance of ESG (Environmental, Social and Governance) investments and the need to secure their “social license to operate” by considering the needs of their stakeholders. In the search for sustainable business models, the concept of the circular economy (CE) is gaining momentum among practitioners and scholars, as it enables the creation of shared value and thus strengthens the trust of investors and stakeholder relationships. However, there is a lack of a sectorspecific CE framework providing guidance to decision-makers in evaluating promising activities. A gap, which this contribution aims to address.

Mar 2, 2022

By Felipe Beluche Lima, Caio Augusto Silva Santos

Brazil is the largest producer of crude steel in the Americas by BOF process and many challenges come along with the increasing market demand. In the BOF, a tubular wall hood structure has been showing premature failures related to the overlay welded tube technology placed in the hood wall. The main root causes were: thermal fatigue at 1800°C, hot spot formation, high heat-affected zone (HAZ) leading to susceptibility of stress cracking, carburizing corrosion and superficial wearing. Based on that, co-extruded tube technology (named composite tube by Sandvik) was the alternative chosen to enhance hood performance without compromising BOF process. In order to rises safety and productivity, composite tube has 100% metallurgical bond assuring stable expansion, high heat exchange efficiency, better corrosion resistance and less rough surface finishing. It was highly suggested to many others mills due to similar and already existing reported cases.

Oct 1, 2019

By Jan Krull

A high productive coke making process in connection with stringent emission control has clearly become a demand of plant operators and stakeholders. Further to this, availability, quality and coal costs are key concerns for the iron and steel industry in its efforts to optimize raw material cost. Today, the optimization of raw material cost in integrated steel works has further gained priority. Coking coal reflects up to 20% of the cost of steel. In top charged batteries coal preparation and blending is one of the concerns to lower coal cost by maximizing the percentage of non-coking coals in the blend. Stamp charging technology is technologically and economically an effective solution in the process of pre-carbonisation. Paul Wurth’s jumbo top charged oven as well as proven stamp charging technology have recently set new benchmarks in Europe, India and Brazil in terms of productivity, stability and emission control.

Aug 1, 2018