Search Documents

By Knight J. L, Baker G

The Wonthaggi coalfield is in South Gippsland, about 90 miles southeast of Melbourne. It is situated on the down-faulted block of the South Gippsland highlands that lies south of the Kongwak fault, between the Powlett River and the sea (Fig. 1). The coal, which is of Jurassic age, occurs in two small, and intensely faulted, limnic basins, that lie on either side of a concealed ridge of Silurian sediments. The coal was first found as thin seams outc1'opping in the cliffs at Cape Paterson, but the seams that are worked at Wonthaggi are concealed beneath a veneer of Cainozoic sands that covers the Jurassic strata, and were found by boring.The c9al seams are worked by the State Coal Mine, which was opened in 1909 to ensure a supply of coal for the Victorian railways, following a prolonged strike in the Newcastle field of New South Wales. The total production from 1910 to June, 1943, amounts to 13,918,800 long tons of coal. The coal seams are faulted to a degree unknown in most coal...

Jan 1, 1944

By R. M. T. Raja Ismail

Shipping and stevedoring industry is going to witness a massive increase in the amount of containers to be handled while land constraints become more critical. Offshore transfer operations hence offer a preferable solution to deal with the surge in cargos rather than to expand the port outwards. Recently, there has been increasing research interests on offshore crane automation. Suspended cargos in a ship-mounted crane system are caused to swing due to the vibratory motion of the ship induced by ocean waves, which can lead to collision between cargos and deck. Therefore, it is vital for offshore crane systems to satisfy rigorous requirements in terms of safety and efficiency. This paper presents the modelling and control development for offshore boom crane systems. A second-order sliding mode control law is proposed for trajectory tracking and sway suppression control, making use of its capability of actuator chattering alleviation while achieving high tracking performance and preserving strong robustness. The asymptotic stability of the closed-loop system is guaranteed in the Lyapunov sense. Simulation results indicate that the proposed controller can significantly reduce the effect of disturbances coming from gusty waves and other dynamic loadings.

Aug 1, 2013

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By P. N. Anyalebechi

"The effects of solidification rate, initial melt hydrogen concentration, and grain refining on porosity formation in aluminum alloy 2024 have been investigated with unidirectionally cooled laboratory-size ingots. The ingots were prepared from melts containing hydrogen concentration of 0.059-0.27 cm3/100 g and solidified at 0.2-37 °C/s. As expected, the amount of porosity, average pore size, and pore number density increased with increase in melt hydrogen concentration and decrease in solidification rate. However, the effect of solidification rate was greater at the very low melt hydrogen concentration (0.059 cm3/100 g). These results are consistent with reported effects of solidification rate and melt hydrogen content on porosity formation in other aluminum alloys. Interestingly, addition of grain refiner slightly increased the amount of porosity and the average pore size, especially at solidification rates above 1°C/s. IntroductionIn shaped castings and wrought products fabricated from ingots, billets, bars, or slabs of aluminum and its alloys porosity formation is a problem. This is because it compromises their tensile strength, fracture toughness, and fatigue properties [ 1-18]. The pores are usually the crack initiation and propagation sites [6,8,9] and the largest pores tend to dictate the fatigue life of the aluminum products [9,10,14]. Porous regions within an aluminum product probably yield first due to the reduced tensile load bearing capacity, causing the concentration of the strain near the voids which subsequently results in premature fracture. In aluminum alloy ingots, billets, bars and slabs porosity formation is particularly problematic because of its persistence through fabrication and potential for reappearance or exacerbation during subsequent thermal treatment processes before and/or after fabrication [19]. In fact, persistence of microporosity is a serious problem in large thick plates of wrought aluminum alloy products that must be rolled from correspondingly large direct-chill or electromagnetic cast ingots. Some of these thick plate products are machined into large aircraft components that are required in service to withstand multi-directional stresses and to possess high fatigue strength, fracture toughness, resistance to stress corrosion cracking, and strength in the short-transverse direction [1,20]."

Jan 1, 2011

By M. R. Yalamanchili

The in-situ FTIR/IRS technique has been used to spectroscopically characterize interfacial water near a hydrophilic surface. Interfacial water was examined spectroscopically over known distances from the surface of a silicon single crystal by appropriate design of the geometry and optics of the internal reflection system. The in-situ FTIR/IRS spectra of interfacial water were examined by consideration of the 0 -H stretching region (3000 -3800 cm-1) associated with the vibrational spectra of water. The broad peak: in this region which describes the interfacial water structure was deconvoluted in order to isolate the overlapping spectral features of the interfacial water. Preliminary spectral results indicate the prevalence of an ice-like water structure (-3200 cm-!) at the silicon surface. Importantly, it appears that the interfacial water structure may extend a considerable distance (several tens of molecular layers) from the surface as established from the spectroscopic depth profile measurements which show that the free OH stretch at 3600 cm-1 becomes very significant at distances from the surface exceeding 400 nm.

Jan 1, 1995

Mine drainage and mine reclamation are topics of major interest to the mining industry, federal and local governments, and the general public. This publication and its companion three volumes are the proceedings of a conference held in Pittsburgh, Pennsylvania, April 24-29, 1994. There were twelve sessions (69 papers) that dealt with mine drainage, including modeling, geochemistry, prediction, treatment, control strategies, characterization, hydrology, and case studies. These sessions comprise volumes 1 and 2. The six sessions (34 papers) that dealt with reclamation and revegetation of disturbed lands are included in volume 3. Volume 4 includes the six sessions (34 papers) that dealt with such topical issues as fires at abandoned mine sites, subsidence, hydrology, mine wastes, and policy. Poster session presentations are represented by 49 papers and 92 abstracts that have been placed in the back of volumes 2, 3, and 4, consistent with the subject of that volume.

Jan 1, 1994

By M. E. Wilson

"The property of McWatters Gold Mines, Limited, is in the east-central part of Rouyn township and about 6 miles east-southeast of the town of Rouyn. It includes 35 claims, the group of 5, staked originally, and 30 claims acquired in later years. The Rouyn-Val d'Or road and the Noranda Senneterre branch of the Canadian National railway both pass within a few hundred feet of the mine.The group of claims in which the mine occurs was first staked in 1922, but gold was not discovered until August 1932 when a schistose zone including veins of quartz carrying considerable free gold was laid bare in a stripped area in the northeastern part of claim R.11604. Diamond drilling undertaken in 1932, and continued into 1933, shouwd that the gold extended for at least 1,000 feet along the strike. A 3-compartment shaft was sunk to 418 feet in 1933. A mill having a capacity of 50 tons a day was constructed in 1934, and enlarged to 150 tons in 1935. Production began in 1934 and continued without interruption to June 1944. Except for a few diamond drill holes, there have been no operations on the property since that time. The maximum depth of the mine workings is 1,50) feet. A total of 368,013 tons of ore having a value of $3,946,752 and an average grade of $11.04 was mined during the years of operation.GEOLOGYThe ore mined from the property occurred within the south limb of an eastward plunging syncline of volcanics and sediments cut off on the north by the Cadillac-Bouzan Lake fault. Because the rock formations within the syncline have been severed from those outside with which they were originally continuous, their correlation is based almost wholly on lithological similarity. They include an irregular middle zone of conglomerate and greywacke underlain by north and south bands of andesite agglomerate and andesite tuff, in which lenticular bands of pillowed andesite are included."

Jan 1, 1954

By Qing-hua Tian, Li-then Cheng, Xue-yi Guo

In order to recycle valuable metals from silver separated residue, a novel method using alkaline smelting at low temperature was proposed. The main factors affecting the main metal recovery such as the smelting temperature, smelting time, liquid-to-solid ratio and alkali addition were investigated comprehensively. The behavior of the main metal elements, such as Pb, Sn, Sb and Bi in silver separated residue was also discussed. The results indicated that amphoteric metals such as Pb and Sn can be smelted into the melt, while other metal elements, such as Sb and Bi were left in the residue.

Jan 1, 2011

By Peter Moon

THE mineral industry of Canada relies heavily upon the talent of its technical men. It is vital to the well-being of the industry that its supply of young, trained men be adequate. At the present time, the industry is acquiring only 200 new graduates a year. The shrinking supply is far below present and future requirements. Other industries and research organizations are competing for engineers and scientists. Dr. J. B. Mawdsley (1), Past-President of the Canadian Institute of Mining and Metallurgy, has recently outlined a program designed to attack the problem. Dr. J'. C. Sproule (2), another former President of the Institute, has stated that: "The need for selection of trainee material is commonly recognized, but little is done about it." The following paper contains a short discussion of occupational interests, and outlines research, using psychological knowledge and measuring techniques, aimed at the identification of desirable recruits for the mineral industry.

Jan 1, 1963

By Mariane Costalonga de Aguiar, Carlos Mauricio Fontes Vieira, Sergio Neves Monteiro

"This work evaluates the effect of incorporation of an ornamental rock waste into an industrial clayey body used for roofing tiles fabrication. Formulations with 0, 10, 20 and 30 wt.% of waste were prepared by replacing the sand in the industrial clayey body. The plasticity of the formulations was determined by the Atterberg limits. Specimens were fabricated by 18 MPa press-molding and then fired from 850, 950 and 1050°C. The specimens were tested to determine the water absorption, linear shrinkage and three points bending flexural strength. The results indicated that the waste improves the extrusion performance of the clayey body by decreasing its plasticity. The use of the waste was beneficial to the water absorption and mechanical strength of the fired clayey ceramic at 1050°C.IntroductionOrnamental rock is a natural resource available in the municipal area of Santo Antonio de Padua and located 150 km from the city of Campos dos Goytacazes, northe of state of Rio de Janeiro, Brazil. Intense industrial activity related to ornamental stones, especially gneisses, is traditionally occurring in the region. After mining, the flagstone is submitted to sawing to obtain blocks and then, after a manual operation, the final products are small flagstones [1,2]. During the sawing operation, a sludge composed of water and fine particles of rock is generated. A monthly production of 1000 tons of ornamental rock waste is estimated to be produced at Santo Antonio de Padua. The final disposal of this waste has brought serious environmental problems. Since most industries do not have an adequate sludge treatment, the waste is contaminating the soil and underground waters as well as obstructing rivers and lakes.Ceramic bodies industrially fabricated in the municipal area of Campos dos Goytacazes, 280 km from the city of Rio de Janeiro, are still empirically elaborated using a mixture of local clays. These clays are predominantly kaolinitic mineral, associated with high plasticity. Due to the excessive plasticity of the ceramic bodies, it is common to have dimensional defects in the final products after the drying and firing processes. Moreover, the kaolinitic structure and the presence of aluminum hydroxide confer a refractory behavior to the local clays. This impairs sintering during the firing operation. In the case of clay ceramics for civil construction, this results in greater porosity associated with elevated values of water absorption [3,4]. To avoid this problem, it is necessary to reformulate the ceramic body composition. The addition of both non-plastic materials to reduce plasticity and fluxes to condition the refractoriness is a possible alternative."

Jan 1, 2011

By Balladares V. Eduardo

Most of the arsenic contained in copper concentrates is removed in the gas phase during the smelting and converting processes and, according to recent environmental regulations, it is required to fix it in a solid stable form. In this regards, ferric arsenate has been reported as thermal and aqueous stable compound. Therefore, various alternatives for treating gas containing arsenic were considered in this work. From data obtained at laboratory scale on fixation of arsenic using iron oxide, a new process to treat copper concentrates containing arsenic was evaluated. The effect of temperature, oxygen potential and the sample porosity on the fixation of arsenic contained in a gaseous stream was studied, and the iron oxide converted into ferric arsenate was up to 10%. The obtained results suggest a new alternative for gas treatment with an interesting and attractive technical development. The arsenic was retained as ferric arsenate with thermal and aqueous stability, and it allows a safe disposal keeping the environmental restrictions. The kinetics parameters are used to scale up laboratory results to higher processing rates.

Jan 1, 2005

By John Vynne

BHP’s Navajo coal mine installed drill monitoring and high precision navigation systems on their three overburden drills during 2002 and 2003. Details of the DrillNav system hardware and reporting system will be discussed, as well as the significant benefits Navajo has achieved since the systems were installed. Navajo is not satisfied with the current results and plan additional upgrades to the systems. In addition, Navajo plan to integrate the data from their drill systems with data from other systems to achieve even greater increases in drill productivity and to reduce overall mining costs.

Jan 1, 2007

By Duclerc Fernandes Parra, Washington Luiz Oliani, Christiano Gianesi Bastos Andrade, Ademar Benevolo Lugão, Danilo Marin Fermino, Francisco R. Valenzuela Diaz

This work concerns the study of the effect of discarded bond paper on the mechanical behavior of polypropylene/organophilic clay nanocomposites. A brown polycationic bentonite from the state of Paraíba, Brazil, was treated with sodium carbonate to transform it into a bentonite that swells in water and then treated with hexadecyltrimethylammonium ammonium chloride to transform it into a bentonite that swells in organic liquids. Polypropylene with 3 % polypropylene graft compatibilizer (PP-g-AM) was mixed with 1 % and 2 % by weight of discarded bond paper and with 1% and 2% by weight of organophilic clay using a twin-screw extruder. The specimens were prepared by the injection process. The clay as received and after organophilization was characterized by XRD, SEM, and capacity of swelling in water and in organic solvents. The nanocomposite specimens were characterized by XRD and thermal analysis. The mechanical behavior of the injected specimens was evaluated by strength, flexural and impact tests. The nanocomposites showed improved mechanical properties compared with the polymer without filler.

Jan 1, 2015

By Nestor Cezar Heck, Aline Lima da Silva

Na produção de vários tipos de aço o controle da composição, tamanho e distribuição das inclusões não-metálicas é de fundamental importância, não só para a qualidade dos produtos siderúrgicos, como também para a garantia da continuidade do processo de fabricação do aço. O controle da composição das inclusões é uma questão que pode ser adequadamente analisada com o uso da ferramenta ‘termodinâmica computacional’, proporcionando ao aciarista informações vitais para ajustes no processo. Neste estudo, com base em cálculos termodinâmicos, foram construídos diagramas de fases especiais com a utilização do software FactSage e seus bancos de dados. Especialmente as influências do Al e do Ti sobre a composição das inclusões foram analisadas, levando-se em conta o teor de oxigênio total. Duas metodologias (estática e dinâmica) foram usadas para se compreender o importante fenômeno da reoxidação. Os resultados deste trabalho, além de auxiliar engenheiros aciaristas a compreender este tipo de análise, deverão estimular estudantes desta área da engenharia a se engajar na assim chamada ‘termodinâmica computacional’.

Nov 19, 2019

By Isabela Costa Mendes Peres

As soldas dissimilares de liga de níquel 182 são utilizadas em usinas nucleares para conectar tubulações de aço inoxidável com componentes fabricados em aço de baixa liga. O procedimento envolvido na soldagem dissimilar pode modificar as propriedades do material, o que afeta diretamente a junta soldada no sentido de aumento da probabilidade de incidência do processo de corrosão. Neste trabalho foi realizado a soldagem dissimilar de corpos de prova dos aços de baixa liga e aço inoxidável austenítico AISI 316L com as ligas de níquel 82 e 182. Estudou-se o comportamento frente à corrosão da junta de solda de liga 182 em ambientes ácidos contendo NaCl e Na2S2O3 empregando-se técnicas eletroquímicas. Ensaios de polarização anódica potenciodinâmica foram utilizados para caracterizar o comportamento de corrosão localizada do material. Os resultados mostraram que o comportamento eletroquímico da junta de solda está relacionado com o aporte térmico e a presença ou não de oxigênio no meio.

Aug 8, 2018

By Marcos Natan da Silva Lima

O aço com alto manganês tem sido estudado como alternativa mais barata em substituição às ligas de aço mais utilizadas, devido as suas propriedades de resistência, ductilidade e tenacidade. Foi alterada a composição de manganês para teores acima dos teores dos aços Hadfield, visando sua aplicação em temperaturas criogênicas. Foram obtidas ligas de aço com alto teor de Manganês através do processo de fundição. O objetivo é avaliar as alterações provocadas pelo aumento do Manganês no aço fundido. Através do estudo realizado no Thermo-Calc®, as amostras da liga fundida foram submetidas à laminação a quente e posterior tratamento térmico de solubilização a 700 ºC, com o intuito de manter a microestrutura austenítica. As mesmas foram analisadas quanto à microestrutura por microscopia ótica (MO) e microscopia eletrônica de varredura (MEV). Os ensaios de dureza realizados confirmaram a elevada dureza das ligas, bem como a variação entre as ligas no estado fundido e solubilizado.

Oct 30, 2017

By Marcos Vinícios da Silva Cavalcante

O processo de um forno de endurecimento de pelotas cruas tipo grelha móvel baseia-se na queima de esferas, aglomerados de minério de ferro, acomodados no interior de carros de grelha que se movimentam com certa velocidade através das zonas do forno. Neste tipo de forno as pelotas cruas são queimadas predominantemente por convecção por gases aquecidos via queimadores instalados na zona de queima. Estes gases quentes passam por entre as pelotas com uma velocidade, densidade, viscosidade e temperatura tal que garante a secagem, a sinterização e o resfriamento das pelotas enquanto são movimentadas dentro dos fornos. A permeabilidade de um leito de pelotas é uma função direta dos espaços vazios formados pelo empacotamento destes aglomerados esféricos que o compõe. Este estudo validado na linha de produção teve como objetivo relacionar os espaços vazios com alguns parâmetros de controle operacional usuais na indústria de pelotização e associá-los a qualidade física, produtividade e ao custo de produção.

Aug 16, 2017

By RENARDIR PEIXOTO MACIEL JUNIOR

Tratamentos térmicos são de grande importância para o desenvolvimento dos materiais, pois alteram as suas propriedades ou conferem-lhes características determinadas. Neste trabalho, foram realizados dois tratamentos térmicos diferentes, recozimento pleno e normalização, em um aço utilizado como eixo de sustentação de aerogerador a fim de verificar as alterações nas microestruturas e propriedades mecânicas através de microscopia ótica, microscopia eletrônica de varredura e ensaio de microdureza Vickers. Além disso, foi realizada a identificação do material por meio de cálculo de composição de carbono utilizando o programa Image J com imagens obtidas por microscopia ótica. Logo, determinou-se que o aço tinha um teor de 0,55% de carbono. Após o estudo comparativo de dureza, verificou-se uma maior dureza da amostra normalizada e uma menor para a amostra recozida em comparação com a amostra recebida (sem tratamento). Logo, alcançaram-se os objetivos esperados ao fim do trabalho, pois todas as etapas foram realizadas com êxito obtendo,dessa forma, uma análise de resultados precisa.

Oct 30, 2017

By Lorena Cristina Amorim, Iara Patrícia Vieira de Oliveira, Leandro Rocha Lemos, Guilherme Liziero Ruggio da Silva, Erick Mitchell Henrique Braga, Paulo Santos Assis

No atual cenário acirrado de competitividade, umas das linhas para redução do custo da mistura de carvões é o desenvolvimento de matérias-primas alternativas nacionais que minimizem o custo do coque e mitiguem a emissão de CO2. O presente trabalho avaliou a utilização de resíduos de shredder (fluff) como aditivo nas misturas para a produção de coque metalúrgico. A utilização de fluff na mistura de carvões minerais sugere uma rota de destinação ecologicamente correta, a fim de mitigar o impacto causado pelo acúmulo desse resíduo no meio-ambiente, além de uma alternativa para redução de custos de produção do coque metalúrgico. Foram realizados enfornamentos, em escala piloto, com adição de fluff, com objetivo de avaliar o impacto sobre a qualidade do coque, especialmente sobre a Resistência após Reação com CO2 (CSR) e a Resistência Mecânica a Frio (DI150-15). Os resultados mostraram a viabilidade técnica da adição de até 1% em massa do material, mantendo a qualidade metalúrgica do coque produzido.

Oct 1, 2019

By Letícia Pegoraro Leal

O mercado mundial está se desenvolvendo continuamente em todos os segmentos com a finalidade de melhorar a qualidade e diminuir os custos. O aperfeiçoamento e a criação de novas técnicas de soldagem são responsáveis por conservar as propriedades mecânicas e realizar as soldas com um menor número de defeitos. Este trabalho apresenta o processo de soldagem por fricção com pino consumível, conhecido como FHPP (Friction Hydro Pillar Process) em pino AISI 4340 e chapa AISI 4140. Como toda nova técnica é importante conhecer os parâmetros que serão utilizados no processo. Compreender o efeito da velocidade de rotação, força axial e de forjamento, consumo do pino e taxa de carregamento são necessários para avaliar sua influência na microestrutura da solda. Desta forma, no presente estudo, após a soldagem foram realizadas metalografias, a fim de analisar defeitos macro e microestruturais. Por fim, verificou-se significativa influência dos parâmetros de processo no comportamento metalúrgico da região soldada.

Aug 8, 2018