Search Documents

By A. J. Rambosek

An evaluation of diamond-bit performance data accumulated from core drilling in quartzite shows that core recovery and physical characteristics of drill bits and diamonds have economic significance. Relatively inexpensive, low-quality, small Congo diamonds will perform as well as, or better than, other diamonds used as drill bart. M-type bits set with oriented Congo diamonds provide those engaged in core drilling with near optimum combination. Various factors that affect bit performance, including size of diamonds, size and type of bits, grade or quality of diamonds, and percentage of core recovered, are evaluated by means of tables, charts, and discussion.

Jan 1, 1958

By Blair J. R

In the Bayer process, bauxite is leached with caustic soda, forming a solution of sodium aluminate, from which hydrated alumina is precipitated. The efficient operation of the continuous form of this process requires that the concentration of caustic soda be controlled. A computer simulation of the concentration of caustic soda has been conducted to provide information, regarding the dynamic behaviour of caustic concentration, which is not available from normal plant data. The basis of the simulation is a state- space model of an alumina refinery, linearized about the normal operating condition. The formulation of the model, with the relevant approximations and assumptions, is outlined. The simulation of the mudwash section of the. plant is described in detail. A continuous model of the mudwash, having time-varying coefficients, was driven using operating data from an alumina refinery. The modelled response showed reasonable agreement with the recorded plant response.

Jan 1, 1977

By J. A. Hudson

"The paper begins with a brief summary of Professor Müller’s formation of the ISRM and the contents of the previous six Müller lectures with their emphases on rock fractures. The geological origin of fractures is described via a deformational spectrum diagram and a matrix characterising the consequences of a sequence of superimposed deformational events. The different fracture frequencies encountered along lines in all directions through a fractured rock mass are explained. The value of computer modelling and simulation is demonstrated through an example of the effects of fracture zones on the distribution of the in situ stress field. The need to establish the validity of computer programs, i.e., that the modelling/simulation, does actually represent the rock reality, is discussed with reference to the work of the DECOVALEX project. Finally, examples are given of the effects of rock fractures on engineering design and construction, from pre-split blasting to caverns.INTRODUCTIONIt is a great honour to have been chosen as the recipient of the ISRM 7th Müller Award and I am grateful to the representatives of the International Society for Rock Mechanics (ISRM) National Groups who voted for me. In addition, I am especially pleased because my working life in rock mechanics and rock engineering has been devoted to understanding the geometry and mechanical properties of rock fractures and rock masses—which were the key subjects that Professor Müller promoted. In the ISRM 50th Anniversary Commemorative Book, Hudson and Lamas (2012), Professor Charles Fairhurst notes that on 24 May 1962, i.e., the day before the constitutional meeting of the ISRM took place in Salzburg, a reporter asked Professor Müller, “Do we know the strength of rock?”, to which Professor Müller replied, “For rock tested in the laboratory, yes. For a rock mass, no. This is what we need to determine. This is why we need an International Society for Rock Mechanics”. Also, in his Opening Address at the 1st ISRM Congress in Lisbon, Professor Müller, as the then ISRM President stated,“Many experts agree with me that discontinuity and anisotropy are the most characteristic properties of the material rock and that the properties of jointed media depend much more upon the fabrics bond of the unit rock block system than upon the rock material. Therefore any theoretical investigation of that material has to go its own ways, in the same way as the construction material of soils years ago suggested to soil mechanics its own methods, which differ greatly from the way of thinking of technical mechanics”."

Jan 1, 2015

By M. H. Salsbury

This report describes the tunneling at the Leadville drainage tunnel, which was resumed in September 1950 with funds made available in the 1950 appropriation of the Department of the Interior. It brings up to date the account of the first project, carried on from December 1943 to August 1945, published by the Bureau of Mines which supervised both the first and second projects. In this report Leadville mining history, particularly related to drainage efforts, and the possibilities for future mine drainage are discussed briefly. An account of the second project, including a description of the operating cycle, exploratory drilling done as a safety measure, surveying procedures, geology, cost data, and other pertinent information, completes the report.

Jan 1, 1956

By R. Heikkilä

Today road construction sites utilize more and more information modeling in design phases as well as model based 3-D machine control systems in site operations. For main contractor, the management and control of all the site operations is a demanding task including also many challenges created by continuously developing new technology. In the paper, the main requirements for successful dynamic site management are introduced. The dynamic management means real-time possibilities for information acquiring, transfer and further utilization of the information in the management. An integration model to expand the current way of management and the utilization of present 3-D machine control systems is introduced. Different practical test results using two new different dynamic management systems are presented and evaluated. The first experiments and the results have been provided using the prototype system developed in a research project called DigiINFRA by the University of Oulu and Technical Research Center of Finland. Also, there have been tested a new commercial management system developed recently in Finland. In the conclusion, an expectation for the next generation for more dynamic road construction management methods is concluded.

Aug 1, 2013

By Goran Vukovic

The use of gas purging plugs in the copper industry is a widely used practice. They provide substantial improvements especially in anode refining furnaces, where savings in process time and energy are obtained as well as refractory wear and buildups inside the furnace are minimized. The newly developed system, enables purging plugs to be implemented in both stationary and tilting furnaces, is in operation in vessels on three continents. An additional advantage in these furnaces above all other benefits is the significantly improved melting rate. This innovative and patented gas purging system consists of a purging plug cooling device and a slidable, cooled piping system. It provides compensation for any thermal expansion in the furnace lining and minimizes the risk of undesirable copper infiltration. User experiences and results of this widely used system are reported in this paper.

Jan 1, 2014

By M. W. Harmer

Laboratory test work, pilot plant testing and plant experience with wet, fine mesh screens is discussed. High frequency, low amplitude, fine mesh, wet screens were installed on the 6th cleaner concentrate stream. These screens produce a 60% oversize recovery split of the molybdenite concentrate that is of leached equivalent quality. The undersize stream is leached with 'hot ferric chloride to remove Pb and Cu contaminates before roasting or shipment to sulfide customers. This plant modification is a good example of using existing technology in an unconventional flow sheet to yield significant cost savings.

Jan 1, 1990

By H. H. Schrenk, L. B. Berger, Robert L. Beatty

"INTRODUCTION Toxic oxides of nitrogen 5/ are formed or liberated in many industrial process and may constitute a definite hazard to the health of persons exposed to the atmospheres thus produced. Oxides of nitrogen occur in the gases involved in the use of explosives, in the gasoline products of welding operations in the exhaust of internal-combustion engines, in the vicinity of electrical discharges, in the combustion of nitrated materials, and in chemical process involving nitration or the use of nitric acid, Itis evident that oxides of nitrogen may constitute an occupational hazard in many industries, and therefore it is important that those concerned with the control of such hazards be equipped with a technique suitable for the determinations of oxides of nitrogen in the concentrations of,hygienic significance."

Feb 1, 1943

By Manuel Álvarez Alvino

El presente trabajo señala el uso de las herramientas tecnológicas en los productos informáticos para controlar las operaciones mineras, dado que no existe un un producto concebido a la medida de cada operación ya que cada realidad es distinta de la otra, tanto en el detalle de la operación como en el aspecto administrativo. En este sentido, es importante la implementación de estos recursos, el control de la gestión, como en el de los estándares de los productos utilizados.

Jul 31, 2003

By Ma F, Yang Q, Ujihira M

The effect of stresses and acoustic emissions on the gas permeability of coal was investigated in the field and the laboratory in order to find an estimative method of the practicability of gas drainage. In the field, acoustic emissions and gas emissions during gas drainage drilling were monitored tentatively at some coal mines in Japan and China.In the laboratory, acoustic emissions from coal specimens in addition to gas permeability were measured during the triaxial compression loading in order to interpret the results monitored in the field. Besides, the opening of gas permeation channels in coal was considered on the basis of the experimental results.

Jan 1, 1991

By Luis Maldonado Astorga

Desde hace más de 80 años, la mina Caudalosa de propiedad de Minera Castrovirreyna S.A. ha sido minada por métodos convencionales como el corte y relleno ascendente, almacenamiento provisional y rajos abiertos. Sin embargo, dichos métodos convencionales para recuperar los rellenos han sido de alto costo de producción y baja productividad, generando un riesgo en su proceso. En ese sentido, el presente texto señala la implementación de una variante de minado en el método Sublevel Stoping (Taladro Largos), donde se evaluó las características geológicas, estructurales, geomecánicas y económicas del proyecto, determinándose la viabilidad del mismo. El método ofrece un minado seguro, productivo, de bajo costo y rentable, orientándo la producción a la recuperación de rellenos detríticos de los tajos antiguos.

Sep 12, 2011

Norway, a country large in area but small in population, has put large effort in protect- ion of its inhabitants in case of war. The Civil Defence has provided shelters for more than 50% of the population. Some of these shelters are put into rock. Since rock installations give large resis- tance against weapon effects and also by advan- tage can be used for several purposes in peace- time, an interesting development has taken place the last decades. In towns and cities you will find sport halls, swimming pools, bowling and shooting ranges etc in rock, which easely can be conver- ted to civil defence shelters. Some typical installations are highlighted in the following.

Jan 1, 1987

By Leonard N. Hill

Cyprus Sierrita Corp. has 16 parallel 5.03 m-diam x 5.8 m long (16.5 ft-diam x 19 ft) primary ball mills, each operating in closed circuit with a nest of cyclones. Before the upgrade to 840 mm (33 in.) cyclones, each mill operated with a nest of five 660 mm (26 in.) cyclones - four in use and one on standby. In this configuration, the mill throughput was 88.5 kt/d (97,500 stpd). Flotation feed averaged 25.9% +212 pm (+65 mesh). The 660 mm (26 in.) cyclones normally operated at an inlet pressure of 34 kPa (5 psi), lower than the inlet pressure of 55 kPa (8 psi) recommended by the manufacturer. The circuit was typically operated with cyclone overflow densities greater than 40% solids to achieve the required throughput. This resulted in inefficient cyclone operation and excessive coarse oversize reporting to flotation. The apexes choked frequently. Larger apexes were tested but reduced the classification efficiency and resulted in circulating loads greater than 800%.

Jan 1, 1994

Watershed Jll in Jefferson County, Ohio we instrumented in 1977 as one of three watersheds established for the purpose of investigating surface mining and reclamation effects upon local hydrology, sediment discharge, and sediment and water quality. Each watershed was less than 50-acres in size, and was in a different geologic setting within southeastern Ohio. Surface runoff and ground¬water levels were monitored. Samples were taken for sediment determination and chemical analysis prior to mining. Monitoring and sampling continued through the period of watershed disturbance caused by mining and reclamation activities, which began in May 1980 at Watershed Jll. A psuedo-postreclamation period followed the initial cessation of man-machine activity on the watershed. A second reclamation effort occurred in the fall of 1981 and was to be followed by a third in 1982 after observations ceased. A true final postreclamation period was not monitored at this site, because the erosion control practice (terrace diversions) failed after each reclamation. Watershed Jll was a small pasture and wooded watershed with sandstone and shale above the mined coal seam prior to mining. A clay layer under the coal supported a perched saturated zone, termed the top aquifer for convenience. A lower underclay supported a second saturated zone called the middle aquifer. A lower perched aquifer had been dewatered by previous deep mining. After about three years of premine data and about two and one-half years of mining reclamation and psuedo-postreclamation data, the following general observations may be made: 1. The mining-reclamation phase was very short, and the postmining period was characterized by erosion failures and remedial disturbances that kept the watershed condition and size in a state of change. It was impossible to collect sufficient data to confidently characterize the hydrologic-sediment-chemical aspects of the mining period or of a postreclamation period and, most importantly, of the future watershed after its various properties and characteristics have ceased adjusting to its severe disturbance and reconstitution. 2. A seeding of wheat followed by grasses and legumes was not a particularly successful reclamation practice in terms of stabilizing the new soil. Numerous rills and small gullies developed in spite of installed diversions. 3. Storm runoff rates and yields at the watershed outlet increased from the premine, (phase 1) to the mining-reclamation (Phase 2) periods, and remained at or near the Phase 2 level through the postreclamation (Phase 3a) period. 4. The top aquifer changed in physical and chemical character as a result of mining and was becoming reestablished as the project drew to a close; but it is impossible to predict its final configuration or character. 5. Dewatering of the top aquifer resulted in a complete cessation of baseflow because the middle aquifer water table lay below the elevation of the watershed outlet. 6. The top and middle aquifers were merged in one area of the watershed where the upper coal underclay was disturbed. 7. Failure of the diversion terraces and their outlet obscured the effects of the reclamation practice upon sediment concentration and yields. There was little difference in sediment concentrations between Phases 2 and 3a. 8. Drinking water standards were met by surface waters throughout the period of observation except for two samples that exceeded the nitrate-N allowable level of 10 mg/l. 9. In all Phase 3 surface-water samples, iron concentrations were within the limits established by OSM, and manganese concentrations exceeded the regulation level only once. pH fell below the lower regulation level of 6.0 between 10% and 20% of the time. 10. The chemical quality of sediments was generally about the same after reclamation as before mining, with the exception of organic carbon, which decreased.

Jan 1, 1983

By G. R. Addie

While the cost of transporting raw phosphate matrix from a pit to a processing plant via slurry pipelines is more efficient than it could be by rail cars, conventional trucks or belt conveyors, it still amounts to many millions of dollars, and in many areas there still exists much room for improvement. By taking advantage of pipeline test data on different slurries, it is possible to reduce costs by optimizing pipeline diameters, operating velocities and slurry concentrations. Better wearing, more efficient pump designs are now available which, if applied correctly, can lead to significant savings. The authors discuss what benefits are possible in relation to the electrical operating and wear maintenance costs and go into some of the factors associated with taking advantage of these benefits, identifying what they see as being practically possible.

Jan 1, 1998

Arguably the SMC Test® has become the most popular laboratory hardness test in the world with over 17,000 tests having been completed to date, covering over 650 different ore bodies. It is now routinely used in design, optimisation and orebody profiling projects. The test is unique in that from relatively small amounts of drill core it simultaneously provides parameters that are used in simulation modelling of AG/SAG and crushing circuits as well as work indices that are used in power-based equations for predicting the specific energies of AG/SAG/Crushing and HPGR circuits. The very large data base that has been accumulated has provided the opportunity to study the differences in variability from deposit to deposit. This paper describes and discusses the trends that have become apparent from the study of this data base. Recommendations for appropriate selection of sample numbers are also made which are based on these trends.

Jan 1, 2012

By C. Sun

With complex component, higher salt content, low biodegradability, DSD acid oxidation wastewater could not be efficiently dealt with traditional methods. It is pointed that the coal water slurry could be made with DSD acid oxidation wastewater of different concentration and the density of coal water slurry could be up to 70%, while its viscosity is only 850~930 mPa?s. The coal water slurry could be perfectly jetted and burnt under different conditions. The higher density the DSD acid oxidation wastewater has, the better properties the coal water slurry have. The pollution components and characteristic group of DSD acid oxidation wastewater are similar to the additives of coal water slurry, so it could be used as a kind of usable additive of water coal slurry. It is so reasonable and feasible to make coal water slurry with DSD acid oxidation wastewater that the pollution of DSD acid oxidation wastewater can be solved completely.

Feb 23, 2014

By F. D. DeVaney

[In the course of the investigation by the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy at the Mississippi Valley experiment Station at Rolla, Mo., on the beneficiation of the low-grade manganese ores of the country, some samples from the Cuyuna District, Minn., have been examined. The work was done under the direction of W. H. Coghill, supervising engineer of the Mississippi Valley Experiment Station. Josoph and Kinney5 in venting about the relative importance of Minnesota deposits of low-grade ore compared to the total reserves say:]

Jan 1, 1930

By Grieveson P, Terry B. S

Carbothermic reduction of sulphide minerals for achieving a selective separation of metallic species from complex minerals has been discussed by considering the prevailing oxygen potential during the course of reaction. Construction of univariant plots for the reduction of sulphides with carbon monoxide gas or carbon and in the presence of either lime or anhydrous calcium sulphate is the key feature of this work. The theoretical calculations for univariants in the Cu-Fe-S-O system indicated a preferential separation of metallic copper and iron by imposing a chemical potential. This is evident from a logarithmic plot of sulphur dioxide partial pressure against reciprocal temperature. The results are compared with empirical data for the reduction equilibrium. The reduction behaviour of the constituent sulphides are also discussed together with the experimental results and theoretically predicted phase stability diagrams.

Jan 1, 1992

By L. C. Galloway, G. L. Tiley

"Mine hoist brakes must meet the following statutory performance criteria:- There should be two independent braking systems; at least one should act directly on the hoist drum.-If one brake fail s, the others should be able to retard and stop the hoist safely before the descending conveyance, carrying the rated load, reaches any obstruction.- When all brakes apply, decelerations should not be so violent that men travelling in the conveyance are injured.- The brakes shall not overheat and fade during an emergency stop.This paper discusses design principles and capacities of caliper and disc type brakes, when applied to double drum and friction hoists of equivalent capacity.IntroductionThis paper is about the brakes that are used on mine hoists; their functions, especially in emergencies, typical design, and how they are operated, controlled, tested, and adjusted.There are two basic types of mine hoists:1. Drum hoists, where the ropes are attached to, and coil on drums. The simplest system has only one drum. Most such hoists, however, have two drums, attached to a common shaft. Ropes are wound on each drum in opposite directions, so that when one conveyance is being raised, the other is lowered. The conveynaces may travel in vertical or inclined shafts. In the latter case, the hoist s are referred to as slope hoists.2. Friction hoist s, where the headropes are not attached to the wheel, but are in contact with it for an angle of lap of, typically, between 180 and 195 degree s. Forces are transmitted from the hoist wheel to the head ropes by friction.The lower ends of the conveyances are connected to balance ropes , approximately the same weight per foot as the headropes."

Jan 1, 1986