Search Documents

By B. T. Darnton

Gravity concentration at the Pegasus Gold Montana Tunnels Mine was initiated in late June, 1991 with the commissioning of a coarse gold scalping circuit that processes a small portion of the ball mill circulating load. The primary objective for the circuit was to reduce the risk of gold particles advancing to flotation that are too coarse to float. The secondary objective was to enhance overall gold recovery and payable gold ounces in a cost effective manner. The gravity circuit has proven itself to be a major success. The above mentioned goals have been achieved, and they have been maintained at record throughput rates that are 30% higher than when the circuit was commissioned. A number of modifications and improvements were made over the last three years which allowed the gravity circuit to keep pace with the higher tonnage, these are discussed in detail in the body of this paper. The overall approach to gravity concentration at Montana Tunnels has always been to optimize production rather than maximize the gold ounces produced. This philosophy has now yielded a circuit expansion and relocation project which will allow for an estimated 50% increase in gravity gold production, while reducing the overall unit costs of production significantly. This paper will review historical gravity circuit performance, improvements, and the current relocation and expansion project.

Jan 1, 1995

By Bin Xu, Qian Li, Yong-bin Yang, Tao Jiang, Jian-jun Hu

It could significantly increase the leaching rate of refractory gold concentrate containing sulfur and arsenic by roasting pretreatment with adding certain amount of sodium sulfate, and the mechanism of that was systematically researched with DSC, XRD and SEM in this paper. Results indicated that the mechanism of Na2SO4 on double refractory gold concentrate at roasting pretreatment can be summed up in the following three aspects：Firstly, Na2SO4 can react with SO2 and SO3 which is produced by the oxidation of sulfides and generate Na2S2O7(l), which plays buffer effect on sulfides exothermic oxidation, avoiding the secondary-encapsulated of gold. Secondly, the liquid phase of Na2S2O7 can cover mineral particles' surface that possesses a sintering effect, it leads to internal cracks of the particles. Finally, mineral particles will gather with sodium sulfate particles as the center that can improve the permeability of the layer.

Jan 1, 2015

By V. V. J. Sarma

Interpretation of earth resistivity data involves not only obtaining depth to interfaces but also determining the nature of formations from their resistivity characteristics. Moore's method of interpretation envisages obtaining depths to the interfaces alone. A simple method of estimating the true resistivity values of formations by applying Hummel's formula of average resistivities is proposed. The method would increase the interpretative value of Moore's method as originally proposed. For most of the earth resistivity measurements, the four-electrode configuration developed by Wennerl is employed. In principal, the method consists of energizing (Current I) the ground through two outer electrodes and measuring the resultant potential (v) between the two inner electrodes. The configuration is such that the separation (a) between any two successive electrodes is equal. The apparent resistivity (pa) for such a configuration is given by 2p- a (V/I). By increasing the electrode separation (pa vs a) curves are obtained. Ideally, a homogeneous isotropic formation underground has a characteristic resistivity. However, the field conditions do not present such ideal cases. Almost invariably, even in the same geological bed, the physical conditions are widely different at different parts in the bed. It is further shown that the penetration of the current into the ground for a given horizontal electrode separation, a, is roughly down to a depth, equal to a. It is therefore, evident that the apparent resistivity calculated from the field observations is a weighted average of the resistivities of the materials present down to this depth. With some prior knowledge about the relative dispositions of the geological formations and their physical conditions, it would be possible, by resistivity surveys, to obtain characteristic resistivities for these formations. It is, thus, that the apparent resistivity-electrode separation curves enable one to decipher the resis- tivity distribution at various depth levels and therefore the nature of the geological formations present. Both empirical and theoretical methods have been developed for determining resistivity characteristics of the various formations. The theoretical methods proposed by Tagg2 and Roman3 are derived from studies of the potential distribution on the surface due to the presence of layers of widely differing resistivities underground. The more recent methods of Wetzel and McMurry4 and Wetzel and Mooney5 are but extensions of the original Roman method of superposition. These methods suffer from lack of similarity of the actual field conditions with those of assumed conditions in developing the theory. The empirical methods such as the one developed by Gish and rooneY6 depend purely on personal observation and local peculiarities, and are applicable only for those limited areas. Out of the empirical methods, moore's7 cumulative resistivity method is still found to be applicable in several localities of differing conditions. While Reudy in 1945 adduced some theoretical justification for the method (Eve and Keys),8 Muskat9 and Mooney 10 tried to show the lack of theoretical basis for the same. It is, however, observed that the method in practice "forms a valuable means of successfully attacking the apparent resistivity curves which fail to respond to the Gish-Rooney, the Tagg or the Roman logarithmic methods" (Ramachandra Rao). 11 Comparatively good results are also reported by Melbyel2 by employing Moore's method in interpreting the resistivity results obtained for ground water in the city of Gunnison, Colo. MOORE'S METHOD As has already been pointed out, the application of the theoretical methods is time-consuming, laborious and sometimes not applicable for quick and accurate interpretation of the field data. moore7 has developed a quick method for obtaining depths to interfaces by plotting the cumulative sums of resistivities, against the corresponding electrode separations a instead of plotting the usual Pa — a curve. In this process of continuous integration, corrections for small variations in resistivities, arising due to local surface conditions or adjacent layers, are made, while large consistent variations are brought out

Jan 1, 1963

By Pedro Boson Gambogi

Aços com microestrutura completamente perlítica são utilizados para fabricação de componentes submetidos a condições severas de carregamento mecânico frequentemente combinado com atrito. Estes aços têm desempenho mecânico afetado principalmente pelo espaçamento interlamelar da perlita. O objetivo deste trabalho foi demonstrar os benefícios do uso da Microscopia de Força Atômica para determinar o espaçamento interlamelar da perlita de um aço eutetóide laminado a quente. Para tal, imagens da microestrutura de amostras retiradas na direção longitudinal e transversal à laminação foram obtidas e processadas com auxílio de um Microscópio de Força Atômica. Como resultado, destaca-se o fato da técnica utilizada ter se mostrado uma ferramenta versátil para caracterização quantitativa do espaçamento interlamelar da perlita. Foi observado espalhamento dos valores medidos do espaçamento interlamelar principalmente influenciado pelas condições de resfriamento do aço durante a transformação austenita-perlita.

Aug 16, 2017

By Élida Gonçalves das Neves

Nos últimos anos as siderúrgicas têm investido na melhoria de seus processos e produtos buscando à produção de clean steels, onde menor nível inclusionário é almejado. Neste contexto foi objetivado neste trabalho, em um primeiro momento, realizar uma revisão bibliográfica afim de buscar um modelo que pudesse relacionar a composição química da escória com a capacidade da escória de remover de forma eficiente as inclusões, garantindo assim a limpidez de aços. A partir destes dados, buscou-se, como segundo objetivo, avaliar alguns resultados de escórias industriais e compará-los com o proposto pelo modelo. A viscosidade e molhabilidade foram os parâmetros de maior impacto neste estudo, sendo a viscosidade obtida através da termodinâmica computacional com o FactSage e a molhabilidade estimada a partir do modelo de Nakajima.

Jul 30, 2018

By Bruna Helena Malovini Loiola

O presente trabalho apresenta os resultados de têmpera a partir da temperatura de transformação da austenita para ferrita em um aço microligado seguido de revenido de 200 a 550°C. Foram avaliadas as fases presentes no equilíbrio termodinâmico em função da temperatura de formação para verificar quais fases foram solubilizadas nas condições de tratamento térmico. Após os tratamentos de têmpera e revenido, foram realizadas caracterizações microestruturais e de microdureza. Os resultados indicaram presença de ferrita poligonal em conjunto com constituintes displacivos como ferrita acicular, bainita e martensita em baixa fração volumétrica. Ambos os constituintes apresentaram variação de microdureza com o revenido e apresentaram envelhecimento na temperatura de 550°C. Este envelhecimento foi atribuído à precipitação de carbonetos tipos M7C3 e MC com base nas simulações termodinâmicas.

Oct 30, 2017

By Felipe da Silva Siqueira, Mariana Sizenando Lyrio, Aline Cristine Lemos Duarte, Weslley Luiz da Silva Assis, Harison da Silva Ventura, André Luiz Moraes Alves, Paulo Rangel Rios

A nucleação nos contornos de grão é um fenômeno muito recorrente em materiais metálicos. Essa situação foi tratada por diversos autores como Cahn e Rios e Villa, usando a abordagem de nucleação em planos e linhas aleatórias. Neste trabalho estudou-se a nucleação nos contornos do polígono de Poisson-Voronoi e de uma matriz hexagonal em 2-d com métodos analíticos e simulação computacional. Utilizou-se uma equação baseada no método de Cahn para nucleação nos contornos de grão. Para nucleação nos contornos do polígono de Voronoi a equação não mostrou adequação total com os resultados simulados para dois tipos diferentes de casos, já para os contornos da matriz hexagonal, notou-se que quanto maior a quantidade de pontos sorteados na matriz, mais os resultados simulados concordaram com a equação proposta.

Nov 13, 2019

By Maria José Santos Lima

Neste trabalho a estrutura cristalina do carbeto de tântalo (TaC), que é um material extremamente duro, com elevado ponto de fusão e elevada estabilidade química, foi analisada por difração de raios- X e pelo método Rietiveld.Para isto, o carbeto de tântalo foi obtido a partir do precursor tris(oxalato)oxitantalato de amônio hidratado, através de reação gás-sólido e sólido-sólido a baixa temperatura (1000°C) e curto tempo de reação, e foi caracterizado através de Difração de Raios-X (DRX), Refinamento Rietveld e Micróscopia Eletronica de Varredura (MEV). Através das analises de DRX e do refinamento Reitiveld para o TaC com S= 1,1584, observou-se a formação do carbeto de tântalo puro com estrutura cúbica e tamanho médio de cristalitos na ordem de 12,9 nanômetros.

Aug 16, 2017

By Niander Aguiar Cerqueira

A construção civil é um setor de extremo impacto na economia brasileira, tanto em termos de empregos quanto no consumo de matérias-primas e geração de resíduos. Resíduos de Construção Civil (RCC) representam uma grande parte da massa total de rejeitos sólidos em médias e grandes cidades. Neste trabalho, um estudo foi realizado para produzir concreto com substituição de areia por RCC, em diferentes porcentagens, a fim de reduzir, reciclar e reutilizar esta grande quantidade de rejeitos da indústria da construção civil. Este trabalho teve como objetivo estudar as propriedades mecânicas de concreto estrutural com substituição total e parcial (25%, 50%, 75% e 100% de substituição de areia). Os resultados do teste de compressão indicaram boa qualidade para os concretos com substituição em massa de até 75% de RCC.

Oct 30, 2017

By André Nogueira

A etapa de flotação convencional do Concentrador 2 ocorre em um circuito com 13 tanques de flotação que recebem o produto dos ciclones limpadores (-0,15mm +0,030mm). O concentrado desta etapa contribui com aproximadamente 80% do volume de produção do concentrador. A necessidade da implantação do sistema de controle avançado de processos (SCAP) advém da alta heterogeneidade na alimentação do concentrador, uma vez que a Samarco não conta com pilha de homogeneização. O objetivo principal do projeto foi maximizar a recuperação metálica da flotação convencional e reduzir a variabilidade do teor de sílica no concentrado final. Aliado ao sistema de análise de imagem de espuma e ao analisador de sílica online, a ferramenta demostrou que, além de atingir os objetivos esperados, trouxe estabilização ao processo e padronização da operação.

Aug 16, 2017

By Richard L. Bullock

At the beginning of the previous chapter, variation in the types of room-and-pillar stopes were briefly identified so that the reader could begin to understand the extensive application of this mining system. These same variations will be reviewed and elaborated upon in this chapter while discussing the methods by which the material is extracted. FULL-FACE SLICING BY DRILLING AND BLASTING When the entire mineralized thickness is taken in one pass of mining, it is known as full-face slicing. There is no mineral of economic value intentionally left either in the floor or the back. Theoretically, there is no limit as to how high the face could be in a single pass. But there are practical limitations to equipment size, pillar stability, and control of local loose slabs on the face, roof, and pillars that dictate current practices. The range of face height of the 15 typical room- and-pillar mines covered in Table 8 (Sec. 1, Subsec. 7) from the Dravo report, 1974 was 1.7 m (5.5 ft) to 9.8 m (32.1 ft), the average being 5.2 m (17.1 ft). In the Gaspe copper mine, Murduchville, Que., the drill jumbos were constructed with an extendable tower for full-face mining up to 15.2 m (49.9 ft) if necessary. However, a more common practice at that mine is to take the ore in multiple slices (Hall, 1959). In many metal mines the normal practice when starting stoping is to drive a single development drift into the ore zone a distance that will allow at least four or five rooms to be opened on each side of the initial drift. Since this opening will probably serve as the main haulage drift, it should be kept as straight and as level as possible. As to the other criteria for the stope developments, it might be well at this point for the mine planner to review the remarks presented earlier (Sec. 1, Subsec. 7) on drifts, entries, and crosscuts for production. After the initial drift is driven, it should be slabbed to the full room width if it is not that wide already. Next, the future pillars should be marked on the ribs and the rooms driven between them. If the ore extends beyond the length of the initial drift and is to be mined in the normal sequence of mining, care should be taken in a random room-and-pillar system to see that the extension of the initial roadway remains straight. If pillar "spotting" is left to the shift foreman or to the miners, they probably will not realize the importance of maintaining a uniform pillar line next to the roadway, and of keeping the line straight. Invariably, a pillar will end up in the middle of the future drift extension resulting in a "dogleg" in a possible main haul- age road. While this error is not catastrophic, too much weaving in and out of pillars will certainly slow down future production haulage and needlessly increase costs. Face or Breast Drilling and Blasting Practices To drill and blast the initial advances into the rock, usually some form of cut pattern must be used. In room-and-pillar mining, when a pattern is drilled in a face and that face is the only exposed surface to which all of the rock must be broken, the pattern is known as a "face round" or "swing." The face to which the rock must be broken is referred to as a "free face." Thus the most common way to advance a room into virgin rock with only one free face is by drilling swings. If, after breaking around a pillar, taking down back, or taking up bottom, there is a second (or third) face exposed, a group of holes drilled nearly parallel to a free face and breaking to it is known as a "slab round" or "slabbing." In some mining districts it is also known as "slashing." Obviously, because two faces exposed offer less resistance to fragmentation than a single face, slabbing requires less drilling and fewer explosives than required to break the same tonnage with the same degree of fragmentation with swings. Therefore, it behooves the driller (or supervisor) to plan the combination of

Jan 1, 1982

By J. J. Beeson

The second part of the paper includes a detailed account of the processes of secondary-enrichment which have been effective in producing the disseminated ores. While both parts present new features, it is hoped that the discussion on secondary chalcopyrite and bornite may be of interest to those who are engaged in the study of secondary processes in other districts. The excellent work' Economic Geology of the Bingham Mining District, by J. M. Boutwell, was published in 1905. Since that time the extensive development work-surface cuts and underground drifting-of the Utah Copper Co. has made possible the collecting of samples for more detailed microscopic study. The writer has taken advantage of this fact and presents the following work, not as a criticism, but as a' continuation of the work which was begun by Mr. Boutwell. b. Acknowledgments.-The present study was undertaken at the suggestion of Dr. A. F. Rogers; to him, and to Prof. C. F. Tolman and Prof. S. W. Young, the writer wishes to express his thanks for criticism in the preparation of this paper. The writer also expresses his thanks to D. C. Jackling, Vice-President and Managing Director of the Utah Copper Co., for permission to publish this paper, and to William Spencer, D. W. Wadleigh, T. S. Carnahan, J. A. Caulfield, Percy Dayer, and Edward Norsefall, for the courtesies extended to him while a co-worker in the mines.

Jan 11, 1915

By G. P. Demopoulos

"The recovery and separation of platinum-group metals (PGM) from primary and secondary materials currently attracts a lot of interest due to the high value of the metals and their increasing demand for high-tech applications. Thus, the traditional refining processes are gradually replaced by newer more efficient separation techniques such as solvent extraction and ion exchange. In this paper the classical and modern refining techniques are reviewed and the pertinent solution chemistry dictating proper processing strategies in each case is discussed. The technological advantages of the modern separation methods are emphasized and reference to the recovery of PGM from primary as well as secondary materials is given. INTRODUCTIONDue to their outstanding physicochemical properties, such as catalytic activity, conductivity and corrosion/oxidation resistance, precious metals now find extensive usage outside of the traditional jewellery and investment industries. The increasing use of precious metals in such areas as electronics and catalysis, as well as their increasing high value, has led to a growing interest in their recovery and separation from primary and secondary materials.Quantitatively the demand of platinum metals in the western world by area of application is described in Table I. Platinum and palladium represent 90% of the total demand, Rh and Ru 8% and the remaining is taken by Ir and Os. In terms of value the following were the average prices (US$/oz) of the metals in the second half of 1986: 500 Pt, 125 Pd, 1200 Rh, 650 Os, 400 Ir and 80 Ru. Due to these prices, exploration, mining, reclamation and refining activity were very high in South Africa, the biggest producer of Pt metals in the world, as well as in other areas: United States (Stilwater deposit), Canada (Sudbury, Marathon and Lac des Isles, Ontario; Kenly Lake, Quebec, etc.), Australia, Europe and elsewhere"

Jan 1, 1989

By D. M. Ward, J. H. Ahrens

"The Fond-du-Lac uranium deposit was delineated primarily by percussion drilling and a small program of diamond drilling. Drillcore samples from three diamond drill holes as well as digitized gamma logs from percussion and diamond drill holes were utilized to define and implement an algorithm for the conversion of gamma-log data to equivalent-grade data. The procedures and detailed analysis for the provision of assay data for uranium reserve estimation are documented.IntroductionThe Fond-du-Lac uranium deposit is on the south shore of Lake Athabasca, approximately 2 km southeast o f Fond-du-Lac , northern Saskatchewan. It is on the northern rim o f the Athabasca sandstone basin.A train of mineralized glacial erratics was discovered in 1967 by Farnok, Limited by means of a helicopter-borne radiometric survey. In 1969, a program of diamond drilling by Famok was successful in locating in-situ mineralization in the Athabasca sandstone at the apex of the mineralized boulder train. Since 1974, exploration and development work have been performed under a joint-venture agreement between Eldorado Nuclear Limited and Famok Limited, with Eldorado acting as operator.From the discovery drill hole to the development of the gamma-log to equivalent-grade con version algorithm, the deposit had been tested by a total of 222 drill holes, 210 of which were percussion holes and 12 of which were diamond drill holes. The holes are generally vertical and collared at 10-metre centres on fences spaced 20 metres apart. The deposit is approximately 390 metres long, 10 to 40 metres wide and up to 45 metres deep, and is generally confined to the Athabasca sandstone. Uranium occurs as pitchblende, coffinite and uraniferou s goethite."

Jan 1, 1983

By Thomas J. Snyder

Modern quarry management should be alert to every opportunity to improve productivity and reduce operating costs. In this paper, the author outlines areas in which explosives suppliers should be encouraged to propose changes. He also supplies guidelines for evaluating these proposals, suggests yardsticks for measurement, and stresses the need to be open-minded when dealing with imaginative, innovative concepts.

Jan 1, 1988

By R. B. Woodworth

In the sinking of bore holes, there are but two fundamental operations —drilling and hoisting—which determine in the main the character of drilling mechanism and structures. There are endless ramifications, however, in the execution of these fundamental operations, according to the purposes for which the bore holes are drilled, their maintenance after completion, the protection and convenience of workmen, etc. The three main lines of use for bore holes are in mineral exploration, the sinking of water and salt wells, and the exploitation of pqtroleum and natural gas. This paper has to do more especially with the last. Here again there are many divergences. Wells may be drilled by either the percussive, the hydraulic, or the abrasive method. Finally, each of these methods, as applied by drillers of diverse nationalities, has followed somewhat different lines of development. The American system of cable-tool drilling has perhaps had the widest application; the hydraulic rotary is also in extensive use; but the Canadian system, the Galician system, and the Russian free-fall system all have their points of recognized merit and are preferred by operators accustomed to their use. These differences in drilling procedure, which rest ultimately on essential variations in geological conditions, are reflected in the drilling structures as well as in the drilling mechanism. The purpose of the present paper is to record those stages in the development of the application of steel to the construction of drilling mechanism and structures with which the writer has been intimately associated, and to contribute to the history of the art of drilling other data acquired in the course of his personal investigations. It is necessarily limited by reason of space to American practice, with especial reference, therefore, to the cable-tool system and the hydraulic rotary method of drilling wells for oil and gas.

Jan 1, 1916

By A. Z. Dimitroff

Immediate detection of methane buildup or of sudden liberation of large quantities of methane in the face area is essential to avert disasters in coal mines. Proper timely detection and handling of methane have always presented problems in extremely gassy mines, and these problems have been magnified by present accelerated mining methods. Strict rules and regulations have been established by coal-mining companies, States, and the Federal Government, which provide for periodic inspections for methane in face areas when electrical equipment is working. Other provisions require the operator' to shut down electrical face equipment and change or adjust ventilation when more than 1.0 percent of methane is detected. Nevertheless, human failure to detect such conditions has been responsible for numerous ignitions arid explosions Recognizing this fact, Marling J. Ankeny, former Director of the Bureau of Mines, proposed in 1958 the development of an automatic methane-monitoring device. He envisioned such a device as being entirely dependable, capable of giving a warning when a predetermined concentration of methane in air is reached, and capable of deenergizing the equipment and rendering it inoperative when a dangerous concentration of methane is present in the air. Such a device has been developed by the Bureau of Mines Health and Safety Research and Testing Center in Pittsburgh, Pa.

Jan 1, 1967

By Lin-fang Shen, Shao-jun Li, Zhi-liang Wang

"The meso-structure of real soil consists of numerous particles with different sizes, while the traditional reconstruction method of quartet structure generation set (QSGS) produce relatively uniform soil particles resulting in significant discrepancy between the actual structure and reconfiguration model. In order to remedy the deficiency, the QSGS is improved by considering the influence of porosity and autocorrelative function of soil, which make the models closer to the real soil. Based on the reconfiguration model, Lattice Boltzmann method is combined in the algorithm to conduct further simulation of fluid flow in soil pores. The D2Q9 model is applied to construct the two dimensional model for simulating mesoscopic seepage field of saturated soil by setting the non-equilibrium extrapolation scheme at the inlet and outlet boundary, and the bounce-back scheme at the soil particles boundary as well as the left and right boundary. According to the case study, the proposed program is realized to simulate mesoscopic seepage field of reconstructed soil with constant inlet seepage velocity. The results show that the seepage direction of soil is along the passage with good connectivity, therefore the permeability is controlled by these passages. The seepage velocity in such channels is faster than in bad connectivity channels. Even if the channel has larger pores, the seepage velocity is still small. INTRODUCTIONUnderstanding the seepage mechanism in porous materials is significant in both theoretical and engineering problems. As a typical porous media, soil consists of solid particles and voids, which form connected channels allowing water to flow through. Such seepage in soil exists widely among geotechnical project of slope, foundation pit, and tunnel, etc. Meanwhile, a number of engineering accidents are caused by limited knowledge of seepage characters in soil (Huang, 2006; Liu, 2013). The conventional method in describing seepage features mostly based on the parameter of permeability, which is a macro statistic mean evaluating the whole connectivity of soil. Obviously, this parameter cannot exactly reflect the details of how water flows through the inner soil structure, especially the flow velocity in local mesoscopic area, hence is unable to represent the actual seepage properties. Therefore, it is necessary to develop mesoscopic approaches to fully study the seepage mechanisms."

Jan 1, 2015

By Jin Yu, Fang-Qiu Zu, Yun Xi, Li-Na Mao

"According to the behaviors of resistivity-temperature of Cu-Sb70 melt, which suggests a partly reversible temperature-induced liquid structure transitions (LST) could occur in this alloy, in this paper, we investigated the dependence of solidification on the liquid state. Both resistivity and temperature were measured to track solidification process. The results show that the nucleating undercooling of the melt which experienced the LST increased and the solidified time decreased. Meanwhile, the solidified microstructures refined evidently, with the microscopic pattern of primary phase changes from disordered pillarlike dendrites into homotaxic ones. Moreover, it is verified that the microstructures would be different if the reversible part of the LST was restrained. The new phenomena and results reflected in this paper suggest that grasping the rules of melt structure change with temperature before material processing will give help for controlling the solidification more effectively and finally resulting in more ideal microstructures.IntroductionThe structure and quality of liquid alloys have a direct and important influence on the structure, performance and quality of the solidified ones. In recent years with in-depth study of liquid structure, researchers have found that some liquid structure transitions (LST) could occur on dependence of the temperature or pressure [1-5]. And the article [6] reported that a pressure-induced reversible LST was found in liquid triphenyl phosphite, which further confirmed the authenticity of the existence of the LST. Furthermore, in our earlier studies of Sn-based melts using resistivity method, some abnormal structure changes induced by temperature have been found at hundreds of degrees above liqiudus, and these LSTs are partly reversible[7]. This phenomenon has been discussed and it is suggested that the reversible LST in Sn-based melts are related to the short-range ordering (SRO) structures of Sn, which are tetrahedron structure with covalent bonding. However, does this reversible LST exist in other melts too?"

Jan 1, 2012

By J. S. Roti

Calcium-based scale precipitation is a common problem in mill reclaim waters. An accumulation of these adherent deposits can result in a rapid reduction in water flow, loss of pump efficiency and eventual interruption in ore production. Heap leach applications can also experience the added problems of plugged sprinkler heads, blinded leach pads and fouled carbon columns when scale control is not maintained. The primary cause of scaling in precious metal recovery is the relative insolubility of calcium carbonate. The presence of the calcium ion and bicarbonate alkalinity is common in almost every water source. If the temperature or pH of the water is allowed to increase, the bicarbonate breaks down to carbonate and combines with calcium by the following reaction: Ca +2 +2HCO3 ? CaCO3 + H2 + CO2

Jan 1, 1986