Search Documents

By D. Kwietnewski

With all of the unknowns associated with tunnel construction, how does a contractor choose a roadheader? This paper presents a review of several models of roadheaders being used in today?s tunnel projects. The features of different models of roadheaders are presented and compared. Roadheader size and cutter power generally determine which roadheader is best for a particular job. We will also present a model for matching features of the roadheader to the anticipated ground conditions such that the most efficient machine is selected for the project.

Jan 1, 2011

By John R. Hoskins

The Bureau of Mines conducted an investigation to more exactly define the influence of some end conditions on the laboratory-determined uniaxial compressive strength of rock samples. Limestone, marble, sandstone, and granite were used to provide a range of specimen modulus of elasticity from 2.7 X 106 psi to 10 x 106 psi. Four variables were studied: Nonparallelism and surface texture of specimen ends were the specimen variables investigated; the end platen size and the adjustable or spherical head friction were the machine variables studied. It was concluded that the loading ends of small laboratory models and samples should be prepared with surface irregularities that do not vary from a plane surface by more than 0.001 inch. It was also concluded that nonparallelism of the specimen ends should not exceed 8 minutes for a rigid head load or 15 minutes for an adjusting head load. The measured compressive strength of specimens prepared with these tolerances will be statistically the same with any diameter or thickness of platen and any degree of head friction if initial alinement of the specimen is assured.

Jan 1, 1968

By Everson P. T, Moyle F. J

Magnesite-rich and dolomite-rich ores from the Savage River region of Tasmania are being considered as potential feed material for a commercial process for production of magnesia.Two selected samples have been characterized by chemical analysis, X-ray diffraction, and differential thermal and thermogravimetric analysis. The materials differ in calcination behaviour, with magnesite decomposing at a significantly lower temperature than dolomite. Calcination conditions have a marked effect on the rate and percentage of magnesium dissolved as the bicarbonate when slurries of the calcine are leached with carbon dioxide. From a process point of view, the feed should have the highest possible magnesite/dolomite ratio, while the optimum calcination conditions are determined by the behaviour of the magnesite component of the feed.From batch calcination tests, it is apparent that the optimum calcination conditions for magnesite-rich ore are a temperature in the vicinity of 700°C and a calcination time of one hour.

Jan 1, 1981

By D. Rutledge

Discrete (digital) signal processing techniques are proving to be very valuable tools for miners using the block cave method. Waveform analysis of different measured signals associated with active mining provides valuable information on production dynamics and safe operation of the mine. For example, correlation of the three-dimensional surface displacement velocity waveform and the production output waveform reveals a remarkably predictable time-varying physical process. In this paper, the authors discuss the signal processing techniques used to study these relationships, as well as the related implications for mining.

Jan 1, 2008

By Wylie A. W, Mathew P. J, Eisler P. L

Field studies of the radiations backscattered by iron ores from a 60Co source of primary gamma radiation located in a borehole logging probe have confirmed thatthe P" factor, a ratio of high energy gamma ray intensities to low energy intensities in selected energy windows of the backscattered gamma-ray spectrum, is a valuable measure of grade for sedimentary iron ores of the Pilbararegion of Western Australia.Laboratory studies of model boreholes have shown that variations in borehole diameter and variations in bulk density of the formations have a significant influence on the measurement of P" ratios. If these influences 'are taken into account the mean ore grade in a new blast hole, for instance, can be predicted with a probe of suitable configuration to within 0·8 per cent Fe at the 95 per cent confidence level, while the grade of a single 120-cm split can be determined to within 2·6 per cent Fe. These results were obtained by pooling data from five blast holes covering the range of iron concentrations 20-68 per cent Fe and apply to the mean hole grades 54-68 per cent Fe.Results for two development holes were generally comparable to those obtained from individual blast holes95 per cent confidence limits of ±0·9 per cent Fe for mean ore grade and ± 4·1 per cent Fe for single splits. A greater number of data points is needed before these confidence limits can be further improved.The technique utilized to obtain these results was derived from a "multiband" approach to collection of backscattered spectral intensity data, an approach which permitted selection at the data processing stage of the most statistically significant P" ratios for the type of mineralization encountered in the field. The multiband technique also permitted selection of the most significant of another set of windows in the backscattered gammarayspectrum to measure a newly developed "S-factor", a ratio sensitive to borehole diameter. Another window provided information on bulk density. All these measurements were made with a single pass of the same loggingprobe.

Jan 1, 1977

By M J. Daniel

Mineral resources all over the world are often heterogeneous and have variable ore properties and ore grade. As a result the ore processed in concentrating plants varies over the life of mines. Consequently the circuits often suffer from bottlenecks typically at the stages of crushing, semi-autogeneous (SAG) and ball milling. Bottlenecks may be remedied with equipment retrofits, however, design engineers should consider a phased approach to the circuit design that delays initial capital expenditure over the life-of-mine. This paper deals with the debottlenecking of existing mineral processing plants by means of high pressure grinding roll (HPGR) applications. It also deals with the use of innovative flow sheet designs using HPGRs for the design of Greenfield plants by engineering or mining companies. In the case of Greenfield plant design an analysis with respect to energy efficiency and operating cost (OPEX) is presented. The analysis compares the performance of SAG based circuits against HPGR circuits that may be influenced by variable ore properties. Globally about 600 HPGRs are installed in various applications in the cement and minerals industries. In excess of 100 of these HPGRs are used since the mid 1980s for crushing and grinding of various ore types including æhard rockÆ applications. HPGR technology is mature enough to be considered as an ideal debottlenecking device. HPGRÆs are versatile, they have a low installation footprint and they are flexible in its machine settings (pressure, roll speed), which can be adjusted to react to ore variations whilst maintaining a high throughput. Examples for the benefits of using HPGR in terms of energy efficiency and operating costs are presented by this paper. æEco-efficientÆ flow sheets and sustainable development initiatives are linked to energy savings as an æenergy costÆ and benefit to the environment. Energy savingsÆ can also be analysed in terms of the ædollar costÆ (OPEX) savings. This paper demonstrates that HPGR is more energy efficient and may reduce the overall grinding energy requirements in the order of 16 per cent depending on the target grind size and ore properties. The HPGR is more cost efficient and may reduce overall grinding costs by as much as 19.3 per cent depending on the cost of energy, grinding media and the rate of grinding media wear in the comminution circuit.

Jan 1, 2009

By Aquiles Vivar

Ante los problemas de sismicidad inducidos por el sistema de minado en la Compañía minera Milpo, se planteó una solución a través del sistema de monitoreo sísmico único, donde se da una distribución espacial de 20 censores entre uniaxiales y triaxiales distribuidos en 3 niveles de producción en el área de influencia de las actuales operaciones para así ubicar, cualificar y cuantificar el fenómeno a efectos de realizar los análisis interpretativos del caso. En ese sentido, el presente texto describe el sistema de monitoreo, cuyo software sísmico está diseñado para determinar nuevas estructuras formadas a partir de los eventos sísmicos pre existentes reactivadas por la sismicidad inducida, así como el desarrollo de planos de isocontornos que permiten la diferenciación entre zonas de altos y bajos esfuerzos.

Sep 9, 2007

By H. Tomlinson

"PURPOSE OF REPORTThe purpose of this report, which is the third of a. series on the coal mines of the Western States, is to give the findings of a study of the causes and methods of prevention of accidents from falls of root and coal in the mines of Lincoln County, Wyo. The three mines covered in this report, referred to as A. B. and C, account- for 9 per cent of the coal production in the county and nearly 9 per cent of the State's total production. For comparative purposes some statistical data are presented bearing upon the relation of injuries to their causes, to tonnage produced, to men employed, to days worked, and to days lost as the result of injuries.FATALITIES IN WYOMINGTo show the necessity for this study, Table 1 given the fatalities that occurred during 1928 in the bituminous—coal mines of the United States, of the State of Wyoming of Lincoln County, and in Mines A, B, and C, followed by a brief description of the Kemmerer coal dis-trict, its coal beds and immediate roof, thickness of cover, dip of coal beds, methods of mining timbering for roof support, roof testing, and supervision. All of these factors must be considered in any plan outlined to prevent accidents resulting from falls of roof and coal.ACKNOWLEDGMENTAcknowledgment is made to the officials of the operating companies for their cooperation and assistance during the study and collection of data to complete this report.GENERAL INFORMATIONLocation and Ownership The mines included in this report are within 18 miles north and south of Kemmerer, Lincoln County, Wyo. (fig. 1), and are owned and operated by various coal companies to supply the domestic, smelter and railroad markets. They are severed by branch lines of the Oregon Shorty Line Railroad Coal production and men employed underground in the three mines are indicated in essential detail in Table 2."

Sep 1, 1932

I had hoped when the time came for me to address this meeting that gold mining would be in a much happier position than we find it to-day.As it is, and because of the demands of national security, we find this great and valuable primary industry relegated to the background and in danger of temporary extinction.These notes refer mainly to gold mining in Western Australia, whence comes the major portion of Australia's production, and their purpose is to record a brief review of the industry immediately prior to the general disorganization that is following the call-up of men from the mines.During this period of reduced production the loss of comparable statistical data will make it impossible to follow the progress of the industry, and, since the period may be long, it occurred to me that information might be derived from an examination of the trend of recent production that would indicate what may be expected of the industry when full production is resumed in the future.Since the revival of gold mining, which started in 1931, most of the old-established mines have reorganized and, in some cases, completely renewed and enlarged their equipment in order to achieve maximum production, and old mines hitherto unpayable have been re-opened and equipped. At the same time large sums have been spent in scientific prospecting and in search for new mines, and it is safe to say that at the end of 1939, when gold production reached its peak, practically every known mine in Western Australia that could be worked profitably was in production.During this period the number of men employed in the industry rose from 5,961 in 1931 to approximately 15,000 in 1939. From the outbreak of war in 1939 to the end of 1941 the output from the mines was maintained at full pressure, maximum tonnage beingrecorded in 1940, although a reduction in the grade of ore treated caused a slight falling off in gold production.During 1941 there was a. fall in both tonnage and grade. The decline in tonnage was due partly to the closing of the Lancefield and Mount Magnet mines, and partly to the shortage of labour brought about by the response of the goldfields to the call for men for the fighting services, the average number of men in the industry in this year being reduced to 12,929.With the entry of the United States into the war in December last and the pooling of the resources of the allied nations, the need for gold as a purchasing medium passed, and with its passing there arose the demand for the transfer of the man-power engaged in gold mining to other fields of industry directly connected with the war effort.There was a ready response by those connected with the industry who...

Jan 1, 1942

By Martin van Staveren

In today's rapid changing construction world, the business pressures on piling and deep foundations reach sky-high levels. Ever increasing complexity of construction projects do severely contribute to these business pressures. Projects are often constructed in densely populated areas and located close to vulnerable buildings and infrastructure. The inherent uncertainty of ground conditions plays a dominating role in these foundation projects. Effective risk management is a key success factor for profitable and sustainable operations of piling and deep foundations. It starts with a fundamental requirement to be aware of risks. Next the different risk perspectives of all stakeholders in any foundation project have to be acknowledged. A simple and structured risk management approach is introduced, to demonstrate that effective risk management is not necessarily that complicated. A major element is the contractual allocation of risks, as a result from differing ground conditions. It is based on the so-called Geotechnical Baseline Report (GBR). The main objective of the GBR is to provide a clear contractual arrangement for the allocation of risks, arising from differing site conditions. The benefits of explicit risk management in general and contractual risk allocation in particular are illustrated with an example and experiences. The presented structured risk management approach, including contractual risk allocation, is still rather new. It proves to be promising for cost-effective risk control of piling and deep foundation projects, anywhere in the world.

Jan 1, 2006

By Frank J. Arland

Augered-Cast-in-Place piles have been used successfully for many deep foundation applications. The four case studies discussed herein describe ACIP pile projects where problems developed during ACIP pile installation requiring changes to the method or sequence of installation. The case studies illustrate the importance of understanding existing subsurface conditions and project constraints when considering the use of this pile type. Ground loosening and over-excavation of soil during the augering process, a significant concern for fine to medium sands and non-plastic silts below the water table, can significantly impact adjacent structures. This risk needs to be evaluated during the pile selection process and generally can be mitigated, but not eliminated, by requiring the use of piling equipment with high torque and slow auger rotation speed to advance the auger with minimum amount of rotation. In some applications where high lateral stresses in the soil are present such as at the base of retaining structures, the use of ACIP piles may not be appropriate if structure movement is unacceptable. On the other hand, ACIP piles have been successfully used to support deep foundations in preconsolidated varved deposits where the new structure was designed to accommodate recompression settlement.

Jan 1, 2004

In his account of the Thackaringa sulphide ore, Lawrence (p. 92) reports the presence of valleriite as a minor accessory in chalcopyrite. He says that it is readily identified by its intensive anisotrophy and reflection pleochroism. He also gives (p. 87) the chemical formula as Cu8Fe4S7 Recent work by Evans et al. (1964), Chamberlain and Delabio (1965), and Schidlowski and Otteman (1966) suggests that most material identified as valleriite is, in fact, mackinawite. Mackinawite and valleriite are both extremely anisotropic and strongly reflection pleochroic, and so with fine-grained material it would be hard to distinguish them optically.Mackinawite, according to Evans et al. (p. D66) is a copper-free iron sulphide (PeS) with small quantities of nickel, whereas valleriite is considered to be a dimorph of chalcopyrite (CuPeS2 ). They found that mackinawite is much more widespread than valleriite, and, unlike the latter mineral, is commonly included in other sulphides, particularly chalcopyrite.Lawrence (p. 92) states that the valleriite inclusions are up to 0·01 mm long, so that an electron probe microanalysis should be quite feasible and provide a ready answer to this query.L. J. Lawrence: I thank Dr Townend for his comments on the occurrence of a valleriite-like mineral embedded in chalcopyrite from Thackaringa. The problem of distinguishing valleriite from mackina...

Jan 1, 1967

From a vast army of workers to gargantuan machines to immense volumes of material being moved, almost everything about the Port of Miami Tunnel (POMT) project points to tunneling on a massive scale. Almost.The star of this underground and underwater show is a Herrenknecht tunnel boring machine (TBM,) nicknamed ?Harriet? by a local Girl Scout troop. With her 12.9-m- (42.3-ft-) diameter cutting head and a total length of 139 m (457 ft), Harriet is boring through thousands of cubic meters of clay, dirt and sand, which is often mixed with coral and other materials, to create two 1,280-m (4,200-ft) traf?c tunnels connecting Watson Island and the Port of Miami (Dodge Island) beneath Biscayne Bay, FL. But in the midst of all of the oversized equipment and machines, a strong contender for the best supporting nod goes to a relatively tiny machine: the Brokk 400. Bouygues Civil Works Florida crews are using the compact, remote-controlled and electric-powered machine to excavate five cross passages between the twin traffic tunnels. The pas-sages will be essential to the safety of people who drive their vehicles under the bay every day.

Sep 1, 2013

By Jorge Castillo

This paper presents a dynamic analyses of heap leach pad stability under high phreatic levels and various levels of seismic loading. The dynamic analysis were conducted as fully non-linear two dimensional analyses with fully coupled liquefaction triggering using the Fast Lagrangian Analysis of Continua (FLAC) computer code. Also, the geotechnical parameters, appropriate earthquake record selection and modification, model calibration, numerical analyses and results are discussed.

Sep 12, 2005

By M. A. Trevits, T. A. Gray, L. M. Crayne, P. Glogowski

Mine seals can he remotely constructed in underground coal mines through vertical boreholes when direct access to a fire is impossible or considered to he too dangerous. This method has great merit because the boreholes can be drilled to specific mine areas, and the seals can be positioned close to a fire zone. The technology however can be largely ineffective if the constructed seals do not provide of effective barriers to airflow or if they cannot he used to impound water and other inert materials. Unfortunately, no viable alternatives exists to sealing the entire mine to the ground surface. Full-scale remote mine seal construction research is being conducted at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory (LLL). Under this effort. Howard Concrete Pumping Company and GAI Consultants Inc. have joined forces to evaluate a potentially significant improvement to the current state of the art. This paper covers the development o f novel technology or rewrote mine seal construction, the evaluation of rite materials used, the construction practice and the Fellow-up testing.

By M A. Mongillo

Most geophysical and geochemical data collected during regional exploration programmes are in vector form (location, value), and have traditionally been presented and interpreted in a profile or contour map format. However, the human vision system can interpret data presented in image format much more easily and new information is often revealed by the judicious application of powerful interactive computer image enhancement techniques. This paper describes a practical demonstration of the application of such tools to gravity and resistivity datasets from the Central Volcanic Region of theNorth Island.   Filtering, contrast enhancement, relief shading, pseudo-colouring and then overlaying of the gridded datasets in image format has helped identify inter-relationships such as the association between many low resistivity anomalies (epithermal deposits or geothermal resources) and the edges of large gravity anomalies (calderas or grabens). Similar revelations should result from the application of these tools to the integration of other mapped datasets from geophysical, geochemical and geological disciplines.

Jan 1, 1992

By Guoqi He

Common offset seismic data collected over two active longwall panels at different stages of mining reveal that significant arrival time delays are produced in reflections from different levels within the mine cover. Mining-induced arrival time delays are also observed beyond the edges of the mine over unmined areas. Reflection arrival time delays increase with reflector depth and are laterally variable. The arrival time delays are produced by reductions of seismic velocity within the overburden. Reflection arrival time delays from a major strong unit located neutrally within the cover are proportional to subsidence, however, delays in other events are not.

Jan 1, 1989

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

A possible process for extracting tellurium and antimony from a residue generated in alkaline sulfide leaching of telluriumbearing alkaline skimming slag was proposed. The central composite design was employed to define the optimal leaching conditions for tellurium and antimony extractions from the residue sample. Using a 23 factorial matrix, the best performance for tellurium and antimony extractions (96.36% and 99.64%) were obtained at 175 g L−1 Na2S concentration for 80 °C during 60 min. The notable degree for influencing tellurium and antimony extractions was leaching temperature, Na2S concentration, and leaching time. The analysis of variance results indicated that the regression model was significant and suitable to be used for the optimization of independent variables within the range. The model was validated under optimal operating conditions based on the experimental design results. Antimony and tellurium in the leach liquor were separated and recovered by H2O2 oxidation followed by Na2S-Na2SO3 reduction. 98.93% of antimony was precipitated selectively during H2O2 oxidation, while 95.06% of tellurium was precipitated during Na2S-Na2SO3 reduction. NaSb(OH)6 and elemental tellurium was obtained as the product.

By Honeycombe R. W K, Greenwood J. N

Powder metallurgy has been developed rapidly in the last twenty years by overseas metallurgists. The technique of making the powders and their subsequent pressing and sintering into useful forms has' only been introduced into Australia under the stress of war-time economic conditions.The technique involved has very little in common with our usual methods of fabricating engineering alloys by melting the ingredients to a homogeneous mass, followed by casting to shape or casting to ingot form and shaping by application of pressure-so-called mechanical working. On the other hand, the technique includes operations, such as milling and sizing, familiar to the primary metallurgists.The compacting of metal or other powders finds important application in two outstanding fields of engineering production: (a) in making porous bearings and contact brushes, in which such a material as powdered graphite can be incorporated; (b) in making cutting tool tips of hard -carbides, which have a melting point too high to make casting feasible, and which would be too brittle in the cast condition in any case. In both these cases; the final article can be made of the desired shape and size (subject to shrinkage allowances) whilst the compact is in a soft and readily machined condition a consideration of great importance in connection with the hard carbides.In order to develop the necessary equipment and technique and at the same time to assisil in the war effort, it was decided to divert the research work of the Metallurgy Department of the University of Melbourne to the problems associated with the production of hard carbides from local raw materials and the sintering of such into tips for cutting tools. Since this work was started at least two industrial concerns have started to produce these materials in the Commonwealth.The work. to date has included (a) the purification of crude cobalt oxide from Risdon and the reduction of this to metal Particles of less than 10 p. diameter; (b) the production of tungsten powder from King Island scheelite and its conversion into tungsten carbide with particle size less than 4 p. diameter; (c) the sintering of the latter product, using the former as a bond; (d) the production of titanium carbide from titanium dioxide; (e) the separation of columbium and tantalum oxides from a Northern Territory tantalite, and the conversion of these into the respective carbides.

Jan 1, 1942

By W. C. Maurer

A study of the mechanics of shear failure of rock under pressure has been made. The transition from brittle to ductile failure occurs when the friction along the fracture surfaces exceeds the shear strength of the rock. A machine has been developed for measuring both the shear strength of rock and the friction along rock fracture surfaces. In this shear machine, the fractures are forced along definite planes; as a result, the rock is stronger than in compression tests where the fractures choose the weakest paths through the specimens. Friction is composed of several forces: (1) the forces to slide irregulurities on surfaces over each other; (2) forces to shear some of these irregularities; (3) molecular attractions across the fractures; and (4) forces required to break bonds resulting from melting and welding at the tips of irregularities on the surfaces. Friction along rock fracture surfaces is not proportional to contact pressure as usually assumed; instead, it increases as the contact pressure raised to the 0.4 to 0.8 power. INTRODUCTION It is difficult to produce tensile stresses under the high compressive stresses present in the earth; therefore, in deep drilling and geological faulting, shear failure predominates. This shear failure mechanism is complicated because rock is a heterogeneous material containing pore spaces, microfractures, elastic discontinuities and other imperfections. A study of shear failure of rock under pressure has been made to obtain a better understanding of this complex mechanism. A machine has been developed and used to measure the shear strength of rock and friction along sheared surfaces. This machine has certain advantages over the compression test — shear properties can be measured under low normal stresses and shear stress and normal stress can be varied independently. The first part of this paper is a description of shear failure of rock under pressure. The role of shear strength and friction along fracture surfaces in the shear failure mechanism will be discussed. The second part consists of a description of the shear machine and a discussion of the shear strength and friction data obtained using this machine. It will be shown that shear strength depends upon the size of the stressed zone, and that friction does not increase linearly with contact pressure as usually assumed. Attempts are made to relate some of the new concepts to tectonic failure and to dril ling. SHEAR FAILURE IN ROCK TRIAXIAL TESTS The shear failure mechanism is illustrated by the triaxial test shown in Fig. 1. In this test, a cylindrical rock specimen is subjected to a confining pressure, PC, and an axial pressure, pa. These external pressures produce normal a and shear T stresses on inclined planes within the specimen equal to1 where 0 is the angle between the specimen axis and a normal to the inclined plane. Fig. 2 shows how triaxial specimens deform as the axial pressure is increased. The pressure is

Jan 1, 1966