Search Documents

By H. D. Outmans

A method has been developed for determining the relative water wet-tability (fraction of the surface wet by water) of porous media. This method involves the adsorption of methylene blue dye from an aqueous solution onto the solid surfaces of rock contacted by the injected dye solution. Experiments on Berea snndstone cores have shown that water-wet cores adsorb a large amount of dye from solution. In oil-wet cores, however, the injected aqueous dye solution is prevented from contacting the adsorptive surfuces by a film of oil and virtually no dye is adsorbed. This method was tested by experiments on mixtures of water-wet and oil-wet sand. Using the dye adsorption method, it was possible to determine quantitatively the fraction of water-wet and oil-wet sarzd in such mixtures. The dye adsorption test is readily applied to determinitrg the relative water wettability of fresh oilfield cores. The cores are not extracted before testing. Observed values of the wettability of field cores tested to date have varied from 100 to 6 per cent water wet. INTR OD UCTIO N Recent articles1 ' have emphasized the important role that wettability plays in almost all phases of reservoir rock behavior. It has been shown that wettability has a profound effect on the interstitial water saturation, residual oil saturation, capillary pressure, relative permeability, waterflood behavior, and resistivity index of oilfield cores. A quantitative investiga- tion of the effect of wettability on these core properties is severely handicapped by the lack of a simple technique for measuring the wettability of a porous medium. If such a technique were available, it would provide investigators with a means of gaining insight into the distribution of phases within a core. A number of qualitative methods of estimating wettability are known. These include contact angle measurements, flotation tests and studies of displacement pressure: imbibition7 and relative permeability data.' Using these tests, it is usually possible to classify a core as water-wet, oil-wet, or some intermediate degree of wettability. One recently proposed method involving measurement of nuclear magnetic relaxatione offers promise of determining quantitatively the fractional wettability of cores. The equipment is rather elaborate and necessary treatment of the cores before testing probably alters the natural wettability. This latter point also applies to most of the cited qualitative methods. This paper presents a new technique for determining water wettability of cores; it is based on measurements of the dye adsorption capacity of the core. This method has the advantage of requiring relatively simple equipment and involves minimum handling of the core before testing. It is important to distinguish between the various concepts of wettability referred to in the literature. The term "wetting" is defined by Bartell as that phenomenon which occurs when a solid and liquid phase come in contact in any manner so as to form a solid-liquid interface. A preferentially water-wet solid is defined by Jennings in terms of the advancing contact angle in the solid water-oil systems. Brown and Fatt regard fractional wettability as the fraction of the total surface area that is preferentially oil-wet or water-wet. However, none of these definitions adequately describes the type wettability measured by the dye test. This calls for the introduction of a new term, "relative water wettability", which we define as the fraction of the total surface area of a core contacted by injected water. DESCRIPTION OF METHOD The ability of a porous medium (especially the clays) to adsorb large quantities of surfactants, dyes, etc., is well known. It is reasonable to assume that a substance can be adsorbed from solution onto a solid surface only if the solution contacts the surface. In this connection Shapiro" has shown by experiments on silica gel that completely dry gel will adsorb methyl red dye from a benzene solution. On the other hand, if a film of water more than several molecules thick is present on the silica gel, the adsorption capacity of the gel for the dye is drastically reduced. Thus, a study of the dye adsorption capacity of cores should give some clue as to the fluid distribution on the surface of the core. TEST OF METHOD As a qualitative check on this theory, dye adsorption tests were run on similar Berea sandstone cores (Table 1, Cores 1-5). Cores saturated initially with water and flooded with 0.01 per cent aqueous methylene blue adsorbed 0.58 mg dye/gm of core. Similar cores saturated initially with water, driven to irreducible water with oil, and then flooded with the same dye solution also adsorbed 0.58 mg dye/gm of core. Another core, treated with a 5 per cent Dri-Film solution, dried and saturated with oil (Soltrol) adsorbed no dye when the dye solution was injected. These tests confirm

By A. C. Fieldner

"Decline of the Beehive Coke OvenTwenty years ago a favorite theme of the crusader for fuel conservation was the enormous waste of valuable by-products incurred in the manufacture of blast-furnace coke in beehive ovens. Indeed, there was good reason for arousing the national conscience to this needless' loss of an irreplaceable mineral resource. In 1910, 83 per cent of the coke production was made in beehive ovens, from which surplus gas, tar, light oil, and ammonia, aggregating in value (at 1910 prices) 40 million dollars annually, were discharged into the atmosphere.In 1929, proportions were reversed and 90 per cent of the production was made in by-product ovens. The average value of by-products obtained in the production of 1 ton of coke in 1929 was $3.60, as compared with $1.16 in 1910, although the value of a ton of coke had increased only from $3.47 to $4.80. As shown in Figure 1,1 the production of by-product coke progressed rather slowly until 1915. War needs suddenly expanded the demand for coke and the by-products benzol and toluol for the manufacture of explosives. Except during the depression of 1921, this accelerating rate of production was maintained up to 1929, largely at the expense of beehive plants. The 1929 production of 60 million tons of coke will probably remain a record-breaking figure for several years. The developments which are now in progress in long-distance transmission of rural gas and in the utilization of volatile petroleum products and refinery gases for augmenting, city gas supplies may retard an other- wise accelerating demand for coke and coke-oven gas for domestic and industrial heating, Trends in Value of By-ProductsThe increasing value of by-products in comparison to the value of coke is shown in Figure 2. In 1913, the average value of by-product coke was $3.38, the value of the by-products per ton of coke was $1.41, and the cost of coal per ton of coke was $3,27, In 1929 not shown in figure) the value of the coke had risen to $4.80 per ton, the value of the by-products to $3.60, and the cost of coal per ton of coke to $5.07. The by-product values in were 155 per cent higher than in 1913, although the coke value had increased only 25 per And the cost of the coal 55 per cent. Actually the increase or the total value of coke plus by-products in this period was very little more than the increase in the coat of the coal, being 55per cent for coal and 60 per cent for coke plus by-products."

Mar 1, 1931

The term geochemistry - chcmbtry' of the earth - is almost limitless in its implied subject, but of recent years a major trend of research in this field has been towards economic application in the search for mineral deposits, and in particular for those of some ofthe less common elements for which a demand now exists.Geochemistry is in a state of slow transition from a purely descriptive subject to a fundamental science concerned with the relationships that exist between the distribution of the elements in the earth's crust and the physical characteristics of the atoms of those elements. The progress achieved promises a set of basic principles which will relate the atomic characteristics of an element to the physico-chemical conditions that make for its dispersion or concentration. This means that, given a geological map of an areasufficiently detailed for the physico-chemical conditions existing in past geological eras to be deduced, there is the possibility that the relative distribution throughout that area of any element present, and its likely mode of occurrence, could be predicted from a consideration of its atomic characteristics.Since the atomic characteristics of the elements are becoming increasingly well defined by physical research, the attainment of this ideal of prediction depends upon:(a) the strengthening of geochemical theory; and(b) the development of petrological and mineralogical methods of assessing the conditions of temperature and pressure prevailing in geological formations at various stages in their history.The other prime requirement is a d.etailed geological map - a requirement that is all too often lacking.The fact that there has been very little "geochemical approach" to problems of economic geology in Australia should not be taken to mean that there is little point in trying to develop such an approach here in as active and as rigidly scientific a manner as possible. The degree of success that has attended the attempts so far made, to which reference is made below, suggests the reverse, particularly in view of the relatively slight cost involved if the investigations were properly organised on a centralised basis. There are three aspects of geochemistry that are directly applicable to the search for economic minerals.(a) The classic technique of the prospector can be made more sensitive and reliable by the use of modern equipment coupled with the application of geochemical theory to geological and structural data. The case of the rare alkali elements (see below) is givenhere as an illustration of the way in which the distribution of elements can be predicted from the first principles of geochemistry, thereby replacing the prospector's dependence on his "sixth sense" that enabled him to suggest that a certain area of formation was"favourable" for the occurrence of a certain type of mineral deposit.At its best, this sixth sense amounted to an almost subconscious correlation of all relevant associations and typical occurrences of the particular mineral experienced by the prospector during his...

Jan 1, 1950

By Richard D. Begley

This paper summarizes the development of a mechanistic model to predict longwall mining induced surface subsidence. The model was originally developed from data acquired from a recent field study conducted in Northern West Virginia. Additional data has been collected from published sources and used to refine the model. The original model utilizes a negative exponential equation to predict the subsidence profile after the maximum possible subsidence is predicted based on the following input parameters: mine geometry, angle of draw and expansion factors for the deformation zones that have been identified above a longwall excavation. The model refinement involved the development of relationships between physical properties of the overburden strata and angle of draw in addition to the expansion or bulking factors. Therefore the refined model now requires only mine geometry and a typical geologic column from the site to predict the subsidence profile. This paper provides the methodology that enables the model to determine the angle of draw and expansion factors breed on physical properties of the site geology i. e. percent of strong rock and Rock Quality Designation of the overburden strata. In addition :comparisons of predicted results with measured data for over H) different sites with various geological and geometrical parameters located throughout the United States will be presented.

Jan 1, 1989

By J. D. Nye, I. A. Farr, W. J. D. Stone

"A unique deposit of barite exists near Brookfield, Nova Scotia. The crystals are extremely fine and the whole deposit virtually free of heavy metals. The deposit size was not large enough for conventional uses, such as the production of barium carbonate and drilling mud. In an effort to obtain maximum utilization, a program was begun to determine if U.S.P.-grade pharmaceutical barium sulphate for X-ray diagnosis could be produced. Early work was sufficiently encouraging to institute a development program under the federal Program for Advancement of Industrial Technology. This has been very successfully completed. Canadian and U.S. process patents have been issued, clinical trials have been successful, a production plant has been designed and the plant’s production sold. The processing plant will include magnetic separation for the removal of iron minerals, fine grinding by paddle milling to minus one micron and acid leaching. The process is unique in that at no time is the barium taken into solution.Information is given on the deposit, process, markets, use, plant capital and operating costs, and projected profits. The initial production plant will have an annual capacity of 2,000 tons per year of end product. Capital cost is $850,000 and annual turnover more than $1.5 million. As this capacity only represents approximately 15% of the North American market, rapid plant expansion is foreseen."

Jan 1, 1980

Hydrogen and carbon monoxide reduction data were obtained on pelletized materials of the type currently being prepared commercially in Australia.Pellets, approximately 1 cm diameter, made from Deepdale, Iron Prince, and Mt. Newman iron ore were reduced by hydrogen over the temperature range 500°-900°C and the reduced pellets were examined by thermogravimetric, microscopic, electron probe, and x-ray techniques. After an initial time delay it was found that up to 95 per cent reduction the data could be described by a porous model where gaseous diffusion through the solid is rate controlling. Independent measurements of effective diffusivity supported the values obtained from the reduction data. Above 95 per cent reduction the rate decreased markedly due to the formation of retained wustite or fayalite.Comparison with reduction by carbon monoxide over the temperature range 750°-900°C showed that the rate of reduction was approximately five times slower than for reduction by hydrogen.The rate of reduction was found to be a function of the initial properties of the pellets which may account for the widely conflicting results that have been obtained with previous investigations on porous pellets.

Jan 1, 1971

By K. D. Russ, A. J. Beer

Non-contact systems for measuring underground voids have used theodolites, reflective or non-reflective laser methods and sonar techniques. An effective but cheaper alternative is based on use of a Wild T1000 electronic theodolite coupled to a Leica Data DISTO and a Wild GRE3 data logger. The software used to process the theodolite data is a spreadsheet and macro combination, while Surpac, Datamine and AutoCAD modelling packages have been investigated for viewing the tunnel profiles. The main limitations were found to be blinding, when irregularities in the stope obstructed the line of sight, and the 30 m range of the Data DISTO model used in the study, although more powerful models are available. All three modelling packages proved suitable, with Surpac providing the best-quality printed images of the voids surveyed and AutoCad by far the cheapest alternative

Jun 21, 1905

By F. J. Sotillo

The reduction in energy consumption has been always important for beneficiation plants. Also gravity separation processes have gained lately great importance due to environmental concerns, especially in the gold and silver Industries. In this sense, the paper point out how to reduce the energy consumption in grinding, and increase efficiency in both grinding and gravity separation are of utmost importance to optimize the use of the country’s resources. For these purposes, chemical additives, such as rheology modifiers have shown great potential, and deserved careful consideration.

Sep 9, 2007

By K. Saikiran, A. R. Nalla

Longwall management, regular shield maintenance, and evaluation of ground control problems can be performed using real-time shield monitoring program. Based on real-time shield pressure data, evaluation of intensity and interval of periodic weighting, estimation of time-dependent pressure increase and the effects of geologic anomalies can be obtained. In this study, full-face shield pressure data of over 457 m (1,500 feet) of face advancement is analyzed to evaluate shield response in the presence of surface lineaments, floor undulations, and multiple main roofs. Shield pressure increase due to web cutting is also correlated with setting pressure during periodic weighting and normal time. In addition, time-dependent pressure increase rate on Sundays and holidays is also correlated with time average pressure and the location of previous periodic weighting.

Jan 1, 2000

By Barry Voight

The law [ ] where [ ] is a measurable quantity such as strain and A and cu are empirical constants, describes the behavior of materials in terminal stages of failure under conditions of approximately constant stress and temperature. Applicable to intact rock and rock masses, the relation may be extended to conditions of variable stress and cyclic stress, and may be used to predict time to failure. Applications in rock mechanics include slope and excavation stability and various topics in ground control.

Jan 1, 1989

By Amy B. Cerato

The application of this study is to use helical anchors as a foundation system for small wind tower (1 ? 10 kW) guyed cables. Helical anchors are currently used to anchor guyed cables of telecommunication and electric towers. However, the increased dynamic vibrations a wind turbine adds to the tower and foundation system under working loads, as well as extreme environmental conditions (e.g., straight line winds, ice load or sudden furling shocks), require additional knowledge about the behavior of helical anchors. These field conditions were simulated in this study by instrumenting a working tower with load cells and 3-axis accelerometers to gather data on wind speed and tower response. These tower responses were then transmitted to the helical anchors through an extensive, large-scale testing program that included monitoring the performance of the helical anchor foundation under dynamic loads, subject to natural variations in both wind regimes, precipitation (water level) and variations in helical anchor geometry. This paper specifically discusses the effects of helical anchor geometry on helical anchor performance under long-term dynamic loads.

Jan 1, 2008

A quantitative chemical model of the rocks of the Broken Hill lode environment is presented to illustrate a stratiform orebody in a meaningful form to scientists interested in environmental control on the chemicalcomposition of sediments.Even though this study was restricted by the narrow range of rock analyses available it is obvious that significant chemical differences exist between the various rock units and also that some association of metallic sulphides with Ca, Mn, Fe, and P is indicated.Correlation of this evidence with that from other mining fields may point out more definite chemical relationships and elucidate the puzzle of the mode of formation of many stratiform orebodies.

Jan 1, 1968

By Flavio Begazo Mamani

Recientemente Southern Perú desarrolló un nuevo proyecto donde se modernizaba la planta de Fundicion y se reemplazaba el convencional horno reverbero por la tecnología del ISASMELT, capturando más del 92% de los gases generados durante el proceso de fusión de los concentrados de cobre. En ese sentido, el presente texto describo los efectos de la modernización de la Fundición sobre la calidad anódica. Antes de la modernización de la Fundición, los ánodos fueron producidos en la planta de ánodos ubicada en la Refinería de Cobre de Ilo. Ahora los ánodos son producidos directamente en la Fundición y como resultado, la composición química de los ánodos ha cambiado, principalmente en el contenido de bismuto, antimonio, plomo y zinc, siendo diferentes a los parámetros de diseño original de la Refinería. Asimismo, este factor impulsó a revisar el proceso de remoción de impurezas y los parámetros de la refinación electrolítica en la Refinería para evitar la contaminación del cobre refinado, logrando mantener la continuidad de la producción de cátodos de cobre de alta calidad superando los estándares interna-cionales de la norma ASTM-B115.

Sep 12, 2011

By Kumar A, Mishra N. C

For each tonne of chromite ore mined in Sukinda, approximately ten tonnes of fine overburden material is generated. The overburden typically contains about 30 - 60 per cent Fe2O3, 0.3 - 1.1 per cent Ni, four to nine per cent Cr2O3 and 0.04 - 0.2 per cent cobalt and is being discarded leading to loss of valuable metals and creating environmental pollution. In order to take the advantage of presence of iron, nickel and chromium, the present studies advocate the utilisation of nickel lateritic chromite overburden for production of Ni bearing pig iron through blast furnace extracting maximum iron and nickel from the chromite overburden. The present paper deals mainly with the beneficiation of chromite overburden, sintering characteristics and thermodynamic studies. The beneficiation study shows that a beneficiated concentrate having Fe - 50 per cent and Ni -- 1.1 per cent can be achieved from chromite overburden having Fe - 30 per cent and Ni -- 0.7 per cent. Sintering studies have been carried out with bed height of 300 and 450 mm at a suction of 600 and 900 WG respectively. The results reveal that good quality sinter can be produced from chromite overburden concentrate with a basicity of about 1.0 and coke breeze consumption rate about 16 per cent. In all the experiments, Tumbler Index, Abrasion Index and Shatter Index was found to be in the range of 65 - 70, 4.5 - 5.5 and 85 - 90 respectively. The other parameters namely softening temperature, melt down temperature, reduction degradation test and relative reducibility have also been determined. A thermodynamic analysis has also been carried out to make a technological assessment of the process for the production of alloyed pig iron from chromite overburden in blast furnace which shows that it is possible to produce nickel bearing pig iron in blast furnace using the sinter up to 80 per cent. Techno-economic analysis reveals that this route will yield a substantial profit even after accounting for cost of beneficiation, extra coke, raw materials and extra slag produced.

Jan 1, 1999

By Y. Q. Zhang, S. S. Peng

Numerical modeling was used to design the pillars and bolting plan for a mine with weak roof and multi-seam stress condition. Previous mining experience, pillar/roof yielding and in-situ horizontal stress were considered in the models. By modeling the upper seam yielding and vertical stress transfer, a multi-seam influence zone was obtained. Appropriate pillar sizes were designed for conditions with and without upper seam stress influences. Roof support for the track and belt entries, using fully-grouted resin bolts and cable bolts, was proposed and implemented in the model. The bolting plan was evaluated under the weak roof condition.

Jan 1, 2004

By Henry Kreisinger, John Blizard, B. J. CROSS, C. E. Augustine

This report gives the results of 26 tests of a four-pass Edgemoor boiler fired with powdered coal at the Lakeside station of the Milwaukee Electric Railway & Light Co. The tests were made by the fuel section of the Bureau of Mines in cooperation with the research department of the Combustion Engineering Corporation and the operating department of the Milwaukee Electric Railway & Light Co. The object of the tests was to determine the thermal efficiencies and capacities obtainable by burning powdered coal under large central-station boilers, and the possibility of operating such boilers continuously at high efficiency and capacity without destructive effect on the furnaces and without difficulties in refuse removal. In any system for burning pulverized coal the furnace is the most important part because, to justify the cost of pulverizing, the powdered coal must be burned with higher efficiency than coal fired with mechanical stokers. In other words, it is the furnace that by giving higher thermal efficiency must pay for the installation, maintenance, and operation of the pulverizing equipment. No matter how simple the apparatus for the preparation of pulverized coal may be, or how simple the pulverizing process, unless the furnace is so designed that it can be operated continuously with high thermal efficiency, the whole system is a failure. For high thermal efficiency the coal must be burned almost completely with low excess air. But low excess air and complete combustion give high furnace temperature, which in turn causes erosion of the furnace lining and fusion of the ash; and removal of the fused ash is difficult. The necessity of complete combustion with low excess air thus brings with it these two important problems in the design of a furnace for burning powdered coal: 1, Prevention of erosion of the furnace lining; 2, easy removal of refuse from the furnace. For the purpose of solving these problems, the boiler tested was equipped with a furnace having hollow walls, through which about 60 per cent of the air needed for combustion passed before it entered the furnace. By passing through the hollow walls, the air cooled the furnace lining and prevented excessive erosion. A water screen was placed in the furnace about 3 feet above the bottom to keep the refuse deposited at the bottom from fusing and to make its removal easy. The design of the furnace, water screen, and burners was based on the experience gained in the previous cooperative tests1 with a smaller furnace, experimental water screen, and burners at the Oneida Street station of the Milwaukee Electric Railway & Light Co. The boiler tested had 13,057 square feet of heating surface. It was one of eight boilers fired with powdered coal, and was designated as boiler No. 8. The Lakeside station is the largest central station in the world that burns powdered coal exclusively. The coal used in the first five tests came from Illinois. The fuel in the other tests -:vas a mixture of Illinois and Pittsburgh coals.

Jan 1, 1925

In dealing with the pulverization and treatment of auriferous ores, it may be stated that there is not one system of treatment applicable to all classes. In the southern portion of New Zealand the ores generally contain free gold, with scarcely any impurity that is, it is found in an almost pure state, without any alloy, and its dissemination amongst the matrix is generally in tolerably coarse particles. The only difficulties the mill man has to contend with, are the economical concentration of pyrites, which in some of the lodes are rich in gold, and the extraction of the gold the pyrites contain. In some of the lodes there is what may be termed float gold, that is, the particles of the precious metal are so finely divided that it passes over the quicksilver tables, and, unless there are other appliances for saving it, this class of gold is entirely lost.Indeed it is only within the last five years that any attention has been given, in the southern portion of the colony, to saving the fine gold that has passed the amalgamating tables. In the North Island the ores are very complex there are scarcely two mines, although they may be adjoining each other, where the bullion is of the same character. On every field the gold is alloyed with silver', and in combination with other metals and mineral substances, such as copper, zinc, antimony, galenfl, iron, sulphur, arsenic, etc., and, in some instaaces, cinnabar, as in the case of the Champion lode at Tui Creek, Te Aroha. Ores of this class are extremly difficult to treat satisfactorily.

Jan 1, 1903

GENERAL CONTRACTOR: ALEXANDER CONSTRUCTORS, INC. STRUCTURAL ENGINEER: CAGLEY & ASSOCIATES, INC. GEOTECHNICAL ENGINEER: F.T. KITLINSKI & ASSOCIATES, INC. PILE FOUNDATION CONTRACTOR: L.G. BARCUS AND SONS, INC. PROJECT PROFILE: 108-10 in. diameter AugerPiles installed to an approximate depth of 32 ft. Piles were installed through Stiff Clayey Fill and Medium-Dense Sands to Decomposed Shale. Piles were drilled to a refusal criteria of 1 ft. / 3 min. Piles were installed using a Barcus Mantis AugerPile rig which is large enough to install piles 25 to 50 ft. long outdoors. The Mantis is also ideal for indoor and low overhead installations. On top of being extremely versatile, the Mantis is also very economical to mobilize. The existing structure is supported on H-Piles. The AugerPiles were furnished and installed for less than the material price of the H-Piles. Design loads were under 40 tons which eliminated the need for a load test. AugerPiles were selected for minimal vibration, limited noise, and economy.

Jan 1, 2001

By Rixon K. L

Hargraves (1983) has reviewed the phenomenon of instantaneous outbursts of coal and gas with special attention to Australian occurrences. The purpose of this discussion is to highlight some problems and omissions in his review that reflect particularly on the authors' structural geological investigations of outburst-prone coal seams.It is surprising to find that much of the authors' reported work has either been glossed over or the results distorted by Hargraves (1983) and it is, therefore, important to clarify the contribution that structural analysis of coal seams can make.For many years it has been known that faults provided preferred loci for gas outbursts (for example, Briggs 1920-21) but the roie that faults played in outburstprone seams was unclear. The present authors reviewed the association of faults and outbursts drawing upon local investigations and the world-wide literature (Shepherd et aI., 1981), and discussed some wideranging aspects that result from the high coincidence of faults and outburst sites. Without repeating large segments of this article the authors will discuss four aspects of coal seam faulting and fracturing.

Jan 1, 1983

By E. J. Roberts

Hydrometallurgical operations and many processes in the chemical industry require the separation of dissolved material from solids. One of the decisions which has to be made in designing a plant for such an operation is how this separation shall be accomplished. It is the purpose of this paper to set forth the general principles involved in such separations in order that the optimum flowsheet and equipment may be selected. Countercurrent Decantation with thickeners, or C.C.D. as it is generally known, is, of course, only one way of separating dissolved material from undis-solved. Other unit operations such as Countercurrent Filtration (C.C.F.) and Countercurrent Classification (C.C.C.) are widely used. The same principles may also be applied to centrifugally assisted decantation, as with nozzle or solid bowl type centrifugals, and to separations using screens, either gravity or centrifugal type. Another form of countercurrent washing applicable to granular materials is practiced in continuous ion exchange operations. All of these operations depend on two basic principles, or combinations of these principles. In C.C.D. type operations the solids are concentrated into the smallest possible volume of liquor in each step and the resulting pulp then mixed with a more dilute liquor and recon cen trated, the liquors separated from the more dilute stages being advanced to dilute the more concentrated liquor in a previous solids concentrate, as is shown in Fig. I. This will be termed the solids concentration-solution dilution principle, or, for short, solution dilution. countercurrent decantation- type circuits. The second principle used in washing solubles from solids is that of solids concentration-solution displacement. Here the solids are restrained from movement while wash solution is forced through the interstices in a counter-current fashion, as in Fig. 2. In the simplest application of this principle, once the "cake" has been formed, it is not disturbed until the operation is completed. In continuous filters, the cake is merely moved under the successive washes and the displaced filtrates removed as in Fig. 4. Often, however, after one or two displacement washes, a repulping step is introduced, the cake reformed and washed again. This procedure brings the solution dilution principle into play as well as the solution displacement principle. Merely thickening ahead of filtration, which is often operationally advantageous, does not hybridize he circuit. It still can be a pure solution displacement operation from the washing

Jan 1, 1961