Search Documents

By Victor Azbe

Azbe System of Controlled Calcination To obtain good and cheap lime there are certain fundamental requirements that need to be satisfied. These are : (1) Proper combustion of fuel and steady supply of heat to the kiln. (2) Proper heat distribution in the kiln. (3) Uniform drawing of lime through the several shaft sections. (4) Complete cooling of the lime and recovery of the heat. (5) Temperature control of the hot zone by economical means. (6) Ample draft to obtain high capacity. (7) Arrangements to facilitate operation. Figure 17 shows diagrammatically one of the smaller kilns, intended for large stone. Such a kiln can be supplied with gas from a centrally located automatic gas producer, or, as shown, from an integral producer located snugly against the kiln. These producers make very good gas and have a gasification capacity of either 10 or 15 tons of coal a day. The producers have water-sealed ash pits, a rather thick fuel bed that is conducive to the making of high-CO gas, and are under forced draft. No steam is used. Clinkering is prevented by admixing some spent gas from the kiln with the air. Coal feeding is from a coal bunker through spouts into the hoppers over the producer. This is done, at proper intervals, by manual operation of slides, but it is planned to install mechanical feeders. Central mechanical gas producers have the advantage of requiring little labour, but the blowing of soot is a problem, as also is the proper distribution of the gas among several kilns. In the case of integral gas producers, soot from the centre burner is blown back into the producer to be burned, and the supply of gas to the kiln is controlled by regulation of air to the producer. In large plants, the mechanical producer may be preferable, but in small ones, the integral producer is cheaper, better, and more reliable. The kiln shown in Figure 17 is suitable for both systems of gas supply. It will be noticed that there are no side gas burners. All gas enters the kiln through the centre burner in a manner that permits any desired amount of gas to be directed to any of the kiln sections by the aid of regulating slides.

Jan 1, 1946

By Slavoljub Makslmovic

One important element of the U.S. Bureau of Mines computer-assisted mining research program is the development of a reliable coal interface detection (CID) system. Several candidate CID concepts currently being investigated by the Bureau include use of natural gamma radiation (NGR), vibration, passive infrared, video, and radar. To help establish which CID sensor technologies need to be developed for a given seam, the Bureau has collected geological and mining practices data from over 460 underground and surface mines in the United States. Also, over 500 coal and rock samples have been obtained for laboratory analyses of ash content, sulfur content, heating value, and NGR. The Bureau's findings indicate that the immediate roof strata in 81% of the underground mines and 93% of the surface mines are made up of shale, draw slate, or claystone. The immediate floor strata in 88% of both the underground and surface mines consist of fireclay, shale, draw slate, or claystone. The results of the NGR testing indicate that the NGR method appears to be a potentially useful CID tool, provided that the immediate roof and floor are both composed of a high percentage of shale-type material.

Jan 1, 1993

By Juan E. Rassmuss

Durante mucho tiempo la explotación del azufre en el interior del Perú, ha sido de manera regular dado su bajo consumo nacional y cotización en el mercado peruano. Asi, solo ciertos yacimientos ubicados en el norte de nuestro país producen y generan divisas que no sobrepasan los 6 millones de soles. En el marco de esta situación, el objetivo del siguiente estudio, pretende reactivar el consumo nacional de los yacimientos del Sur del país, -en tanto volumen e importancia comercial por medio del uso de un método de beneficio apropiado. La formación de los yacimientos del Sur, a diferencia de los de Piura y Bayovar, se da por la emanación postvolcánica de gases sulfurosos, generandoimpregnaciones de azufre en las lavas y tufos del Terciario Superior y Cuaternario. Posteriormente se produjeron fracturas en las zonas contíguas de los volcanes, formando depósitos lenticulares de extensión variable. Dichos depósitos son superficiales puesto que solo cerca de este espacio se puede mantener la oxidación del sulfuro de hidrógeno y los gases están a temperatura baja para depositar azufre. En cuanto al costo del azufre tenemos el costo de explotación, beneficio, transporte y embarque. Finalmente, se deduce que la fundición del azufre como la filtración, soliflucción pueden ser favorables en el uso de métodos de explotación menos costosos, asi como el incremento de la explotación depende de un mercado común estable y de un cálculo exacto de los costos de producción.

Jul 20, 1956

By W. P. Campbell

In the course of the development of the Red Coulee field, northwest of Coutts, Alberta, a considerable amount of information has been gathered by the Department of the Interior regarding the chemical character of waters encountered in the drilling of wells in this area. The writer, in this paper, has undertaken to assemble the available material with the idea of deducing what relations, if any, may exist between the different waters from the same well, and also how these compare with waters encountered in similar horizons in other wells. From no other district, with which the Department of the Interior has had to do, have there been received so many samples of water, and yet not all the waters logged in the drilling reports were sent in for analysis. The information, therefore, herein contained is not as complete as the writer would have desired, but sufficient evidence has been accumulated to indicate some very definite tendencies in the chemical nature of the waters of this field. The drilling of Red Coulee wells has been carried out exclusively by percussive tools. These permit 'dry' drilling, and, consequently, water-sands are recognized when encountered. Had rotary tools been used, information regarding water-sands would have been very meagre, if not entirely lacking, since, in the mudding-off process, water-sands would have been overlooked, with the result that, should water break through into a completed well, its source would not be known and remedial efforts would be greatly handicapped, if not entirely defeated.

Jan 1, 1931

By S. H. Chauvenet

Jan 1, 1882

By S. Mohanan, C. R. Kumar, S. K. Bhoja, T. Venugopalan

"A pressing issue that has often been the topic of discussion in iron-making operations in India is the high content of alumina in the country’s iron ore deposits. The presence of alumina has hampered production by affecting slag fluidity, and thereby the hot metal quality. Iron ores from Indian mines are generally rich in hematite, with traces or small amounts of goethite/limonite, kaolinite, gibbsite and quartz reported from time to time. In day-to-day production, emphasis is placed on checking the chemical analysis of product samples, but the true solution to the alumina problem lies in estimating the mineralogy of the ore samples. We developed a mathematical model, based on singular value decomposition, to predict mineralogy from classical chemical analysis. We then used X-ray diffraction patterns, scanning electron microscope analysis, and grain counting with an optical microscope to determine actual mineral compositions and to test the values predicted by the model. The results indicate that with regular calibration, the model can be used as a simple, fast and effective tool to predict on a regular basis the mineralogy of multiple samples.IntroductionIndian blast furnaces use high-grade iron ores (as lumps or as sinter) and coke (obtained from the destructive distillation of coal) as raw materials for the production of high-quality hot metal to be converted into different steel products through the Linz- Donawitz process. The iron ores are mainly sourced from the Singhbhum region of Odisha and Jharkhand states, the Bailadialla region of Chattisgarh state and the Bellary region of Karnataka and Goa states, and are mainly classified based on size as (1) lump ore (fed directly into blast furnaces), (2) fines (converted into sinter/pellets and fed to blast furnaces) and (3) slimes (< 0.15 mm; currently dumped in huge slime ponds). Any variation in the quality of the ores supplied results in variations in the production trends of hot metal."

Jan 1, 2015

By Constantine C. Popoff

This report reviews and analyzes, by a simple analytical and logical reasoning, the conventional methods of reserve computations of mineral deposits described in various domestic and foreign publications. It brings together, formulates, and evaluates the principles underlying interpretation of exploration data; and ties such principles to the proposed classification of methods. The material is discussed in sufficient detail to allow general application.

Jan 1, 1966

By R. L. Marek

The number of persons fatally injured in the California petroleum industry in 1932 was 24, a decrease of 6, or 20 percent from the number killed in 1931. The decrease in the number of fatalities occurring in 1932 caused the fatality curve of the California petroleum industry to reach its lowest point in 10 years. Changing conditions in the oil industry - reduced personnel, decreased active field development, and curtailed production - have undoubtedly caused a part of this decrease, but continued accident-prevention efforts by the industry have also contributed to the reduction in the number of fatalities for 1932. The Bureau of Mines has analyzed and reported annually the fatalities in the California petroleum industry for a period of 10 years. Figure 1 shows the trend of fatal accidents during that period. Fatality statistics for 1932 show that the drilling and producing, pipe line and transportation, and refining and natural gasoline divisions of the industry had fewer accidents in 1932 than in 1931, sales and marketing being the only division that showed an increase over 1931. The number of fatalities by divisions for 1931 and 1932, percent of total, and percentages of increase and decrease are given in Table 1.

Jan 1, 1933

By L. Bos

The availability and reliability of large grinding mills and their Gearless Mill Drives (GMDs) are of paramount importance for the grinding process. Although GMDs have been in service for decades, and are known for their operational efficiency (reliability and robustness with reduced operating cost per ton), compared to conventional drives, in the last decade due to certain reasons some failures led to serious unscheduled shutdowns and significant insurance events. The majority of these notable "insured" failures have happened on GMDs installed on relatively large mills, as the financial impact of a failure is proportional to the through-put of the mill. Despite the occurrences of these events, as mining operations are driven by lower ore grades and the ability to continue reducing operating costs per ton, the trend for having larger mills is still very present and there is no reason why this trend should not continue. It is obvious that if not handled correctly, the possibility of large value GMD loss events, coupled with the continuing increase in mill size or required availability and reliability targets, could potentially lead to major conflicts as it becomes difficult for the insurance companies to judge the risk and hence may result in hesitation to insure these grinding circuits. This paper will not only describe the conflicting situation from both an insurer&apos;s perspective and from an equipment supplier&apos;s perspective, but also how these conflicting challenges can be successfully mastered. It has to be noted that not only the mining companies themselves, but also their insurance companies and the involved equipment suppliers have a common interest: to reach the highest availability and reliability in order to avoid or at least minimize unscheduled shut down times, and most importantly prevent unplanned events that result in extended production stoppages or reductions in through-put of GMD driven mills. From the very beginning onwards, the complete service concept together with emergency plans must be integrated on every level in the design of the grinding circuit. This approach must be implemented continuously and without compromises by all involved parties during all following stages, such as basic design, detail design, manufacturing, quality inspection and testing, packing, transportation, storage, installation, commissioning, operation and maintenance. The concept of formal risk analysis related to mill operations, maintenance and spare parts strategies must be an integral part of mining companies? decisions related to the selection for installation and continued use of large mills powered by GMDs. The service concept in place for operating mills shall also have a clear focus on very early detection of any abnormalities, so that the risk can be mitigated and unscheduled shutdown times avoided. However, if a major failure occurs, then procedures and tools shall already be available in order to ensure that production impact is minimized.

Jan 1, 2012

By A. L. Mular

A great deal of effort is being expended by mineral processing engineers to acquire a basic knowledge of modelling and optimization techniques. Stimuli such as immediate process improvement, expanded process understanding, optimal flowsheet design and re-design, and the development of new and better control systems are goals which excite the imagination in terms of increased profits. To reach these goals, process models and efficient optimization strategies, regardless of their purpose, assume an important role. Consequently, few of us can argue that such efforts are of no value. The purpose of this paper is to review empirical modelling methods and optimization strategies which appear to be of value to mineral engineers.

Jan 1, 1972

By R. Shimpo

Equilibrium calculations by a computer may sometimes fail in giving solutions when the system includes a large number of components and more than three phases, and especially when no definite information about stable phases is given. An improved method of calculation is presented in which the number of phases need not to be initially fixed, phases can appear or disappear in the course of&apos; calculation and a new method is combined with the Newton-Raphson method to obtain solutions easily. The improved method is applied to the copper smelting operation and all the successive stages of the operation are successfully simulated.

Jan 1, 1983

By Wilbur L. Webb

This publication reports on the design, fabrication and test of an Improved methane monitor system for compliance to 30CFR75.313. The system will Initiate automatic shutdown of mining machinery when excessive concentrations of methane are encountered. The prime consideration: In the design were small size, Improved accuracy and reliability, fast response and a transient resistant power supply capable of reliable operation from any mine power source. The power supply contains an internal battery that provides operating power to the detection system prior to mining machine start-up or after machine shutdown. This report documents the development program from conception through in-mine testing.

Jan 1, 1978

By Irving Wender

This report describes Bureau of Mines experiments and reviews the work of others on the exposure of coal and coal-derived products to gamma rays and some other types of radiation. Results are presented on tests of three bituminous coals and a lignite that had been pulverized to minus 200-mesh particles and exposed to 1,000 megaroentgens of gamma irradiation from spent-fuel elements of a nuclear reactor. Of about 20 chemical and physical tests in Bureau work, only mass spectrometry of gases evolved during vacuum pyrolysis of the coals to 450° C gave results indicating differences in the irradiated and unirradiated samples. Mass-spectral distribution curves for CO and CO2 evolution showed fewer irregularities (reversals of curvature) for irradiated coals; thus, mass spectrometry appears to be the most sensitive method for determining radio-induced changes in coal. It is concluded that coal is not significantly altered by gamma irradiation owing to the resistivity of its highly condensed ring structure. High-level gamma irradiation, therefore, is unlikely to prove advantageous in coal processing and utilization. Specially treated coals, because of resistivity of coal to radiation damage, may be useful as an absorbent in processing radioactive wastes.

Jan 1, 1968

By W. M. Husslage

The permeability in the blast furnace shaft is adversely affected by low temperature reduction degradation of sinters. The fundamental cause is an expansion of the iron oxide phase resulting from reduction of hematite to magnetite. The present study showed that expansion behavior during the hematite / magnetite reduction step and the resulting microstructure are strongly influenced by the reduction temperature (viz. partial oxygen pressure), the reducing agent and the nature of the hematite. The reduction rate is of minor importance. A reduction mechanism is proposed, explaining the dilation behavior and the magnetite microstructure. The results can provide better insight into reduction degradation behavior.

Jan 1, 1998

By Joseph D. Davis, GEORGE S. POPE

This bulletin is the fourth of a series a showing the results of the purchase of coal by the Government under specifications. The work of inspecting and analyzing coal delivered on Government contracts was transferred to the Bureau of Mines by an act of Congress effective July 1, 1910. It had been carried on for several years before that date by the technologic branch of the United States Geological Survey. The purchase of coal on the dealer's statement as to quality or on the reputation of the mine or district producing the coal is gradually being discontinued. At present most coal-purchasing contracts make definite provision regarding the desired heating value of a coal and the composition as shown by analysis. The heating value is usually expressed in British thermal units" and the composition specified is that shown by proximate" analysis. The price to be paid for delivered coal is made to depend on whether the analyses and heating-value tests of samples representing the delivery show the quality to be above or below the quality set forth in the contract. Large coal consumers are beginning to appreciate more and more the importance of the cost of power as a factor in the cost of producing a finished article. The endeavor to increase the efficiency and the economical operation of a power plant calls for an intimate knowledge of the quality of the coal being used. The purchase of coal under specifications insures the purchaser getting what he pays for and the coal being of the quality guaranteed. In addition, the analyses and tests of the delivered coal furnish data whereby the power-plant results can be comprehensively studied and a continuous check maintained on the conditions of operation.

Jan 1, 1912

By B Reid

"Since the commencement of mining operations at the Cowal Gold Operations (CGO) in 2005, reverse circulation (RC) drilling has been the preferred method for grade control (GC) sample collection. This method was selected because it allowed:for multibench drilling (20 m hole depths for two benches of mining) to aid mine planning increased data density for comparison against the wide spaced ore reserve model angled drill holes to intersect perpendicular to the strike and dip of the shallow dipping mineralisation ability to take two metre sample intervals to enhance the understanding of the mineralisation’s short-scale variability and provide the ability to flitch mine.From June 2008 to December 2013, RC GC was performed using a UDR rotary cone splitter. The field duplicate data over the period displayed strong precision, with a correlation coefficient of 0.94 and an average relative per cent difference (RPD) of 21 per cent for gold. Up to 66.1 per cent of field duplicate data greater than 0.1 g/t fell within ±20 per cent RPD. This is within limits of industry best practice. The Mine to Mill reconciliations over the same period showed the estimated GC grade was 7.7 per cent lower than the calculated head grade (CHG).In December 2013, the Progradex sampling system (PGX) was introduced at CGO due to its advertised ability to capture 100 per cent of the drill cuttings for the complete sample interval, inclusive of fines. Analysis of field duplicate data indicates that since the introduction of the PGX, the sample precision has drifted. From January 2014 to February 2016, the correlation coefficient was 0.92 and up to 51.2 per cent of field duplicate data, greater than 0.1 g/t fell within the ±20 per cent RPD. Over the same 26 month period, the Mine to Mill reconciliation improved to one per cent lower than the CHG. Granulometric analysis of the RC samples collected from the PGX indicated the fines material(&lt;212 µm) averaged up to 22 per cent of the samples mass and following assay determination, the fines material represented a weighted average of 31 per cent of the total gold content within the sample.This paper highlights the:importance of the complete capture of all drill cuttings during an RC drill programinfluence of fines material on the sample quality and accuracyimpact sampling of the fines material has on the Mine to Mill reconciliation performancechallenges experienced in commissioning a PGX system.Citation:Reid, B, 2016. A Fine Looking Sample - the Importance of Fines in Grade Control Sampling to Mine to Mill Reconciliation, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 28–38 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By W. H. Oppelt

Converting small-particle lignite to a stable, storable fuel of relatively high heating value was investigated. The fuel was prepared by thermal pretreatment of the lignite in an 8-inch i. d. rotary-drum retort, then the pretreated material was pelletized in an experimental 15-inch-i. d. rotary-drum pelletizer. Pelletizing tests were made with both starch and bituminous binders. During the first phase of the project, the quantity, composition, and heating value of products from the thermal processing of Kincaid lignite from Burke County, N. Dak., in an B-inch i. d. rotary-drum retort were investigated at a series of temperatures from 250° to 950° F. to establish optimum conditions for preparing feed material for pelletizing. To determine the response to thermal treatment of different lignites, 5 other lignites from Divide, McLean, Mercer, and Stark Counties, N. Dak., and 1 lignite from Saskatchewan, Canada, were processed at 700° F.

Jan 1, 1958

By Frank J. Wiebelt

As a result of the examination of many copper-zinc properties in the West Belt area of California, nine were chosen for exploration projects by the Bureau of Mines. This was part of the Bureau&apos;s wartime mineral-development program aimed at maintaining production of essential metals and increasing ore reserves. The properties explored were the El Dorado, El Dorado County; Copper Hill, Newton, and Gray House, Amador County; Constellation, North Keystone, and Collier, Calaveras County; and American Eagle and Akoz, Mariposa County. In addition to surface sampling and mapping, 41 holes, aggregating 18,134 linear feet, were diamond-drilled. Detailed results of the work done on all properties except the El Dorado and Akoz are given in this report. The El Dorado and Akoz were discussed in Reports of Investigations 3896 and 4144, respectively. Figure 1 is an index map showing the location of the mines covered in this publication.

Jan 1, 1951

By S. J. Thomas, P. A. Lilly

With support from the Australian mining industry and the Federal Government, three Australian universities are collaboratively developing flexible-format, web-based course content and delivery in rock mechanics for undergraduate mining engineering students. This paper describes the educational philosophy behind the development and summarises other salient features of the Program. Mit der Unterstuetzung von der austlalischer Bergbauindustrie und der Bundesregierung, drei austlalische Universtaeten in Zusammenarbeit entwickeln flexibel Netzgengruendet auf Lehrganginhalt und Lieferung in Felsgestein fuer Bergbaustudenten. Dieses Schreiben erlautert das Unterrichtsphilosophie hinter der Entwicklung und Zusammenfassung anderer Hauptpunkte von diesem Programm" Avec l&apos;assistance de l&apos;industrie miniere australienne et du gouvernement federal , 3 universites Australiennes collaborent a la mise en place d&apos;un programme de mecanique des sols pour etudiants- ingenieurs en mines. Ce programme serait a la fois flexible et accessible par Internet. Ce document decrit la philosophie pedagogique de ce projet et en souligne les characteres importants.

Jan 1, 2003

By Praterm J. D.

The process parameters for effective utilization of nitric acid as an oxidant for copper-iron sulfides have been developed. Leaching variables found to be important were acid concentration, temperature, time, atmosphere, pressure, mineral type, particle size, and percent solids. Particular attention was devoted to analysis and control of fumes evolved during the oxidation. Responses recorded were metal extraction, elemental sulfur formation and oxidation, product gas composition and evolution rate, reagent consumption, and residue flotation response. The paper concludes by laboratory testing a flow sheet based on the above observations. Ninety-eight percent of the copper contained in a chalcopyrite-bornite concentrate was recovered, requiring 1. 6 pounds of nitric acid to be regenerated externally per pound of copper extracted. Iron remained in the leach residue as hydrogen jarosite and was ultimately rejected from the system by froth flotation. Sixty percent of the sulfur contained, in the heading concentrate reported in the elemental form; the remainder was oxidized to sulfate and eliminated with the hydrogen jarosite in the flotation tails or by neutralization of the solvent extraction raffinate with lime. Nitrogen was evolved primarily as NO and NO2; up to 3 percent N2O was also present. Gases containing sulfur were absent except when pyrrhotite was solubilized in the absence of soluble copper. In this case, H2S was evolved.

Jan 1, 1972