Search Documents

By Boyd Guthrie

As the American petroleum industry surveyed its position in early 1937, it had many reasons to be optimistic concerning its future. The industry had emerged successfully from the depression, and for the first time since 1929 it had produced over one billion barrels of crude oil in a single year. The demand for gasoline and fuel oils was up, and reserves of crude petroleum and production capacity seemed adequate for the future. Although production of crude oil dropped slightly in 1938, the oil industry was still in a good position with respect to its supply of raw material, which improved economically in 1939 with the decrease of crude-oil stocks in storage above ground. However, by 1940 a threatening cloud (the invasion of France and its rapid surrender) had appeared on the horizon. This aroused Somme fears as to the industry's immediate future, and these fears were intensified the following year when the United States entered World War II. As the war progressed, more and more ships, planes, and vehicles were produced, and the problem of obtaining enough liquid fuels to supply them intensified. Hearings were held in August 1943 before a subcommittee of the Committee on Public Lands and Surveys of the 78th Congress to determine the advisability of passing legislation to promote the development of synthetic liquid fuels.

Jan 1, 1951

By O. Llewellyn Jack

From September 1978 to December 1983, ESD Corporation (formerly a Division of FMC Corporation) undertook the development and testing of a bidirectional auger under contract with the U.S. Department of Energy. Underground testing began in August 1981 at Peabody Coal Company's Marissa Mine near Marissa, Illinois. The auger was developed to increase mine production and coal recovery without increasing land subsidence. It bored 4-foot-diameter by 10-foot-deep holes into pillars on 7-foot centers (each hole recovering 5 tons). All operating during this test was performed by maintenance personnel with the goal of finding ways to increase the machine potential. The maximum excavation rate achieved was 1.4 tons per minute. It was concluded that the concept of drilling short holes to extract coal from underground pillars without surface subsidence was practicable with a wheel mounted auger, but that more power was desirable for this mine, and that the hydraulically driven augering system that provided experimental versatility was not sufficiently reliable for production use.

Jan 1, 1983

Slide presentation at conference

Jan 1, 1996

By J. J. Forbes

Ventilation is the most important safety factor in the production of coal because on it depends the safety, health, and efficiency of those who work underground. Without adequate and efficient means of supplying fresh air to the working faces, mining could not have advanced as it has. The extent of the workings, the increase in mechanization, and the increasing use of electricity are largely responsible for changes in methods of ventialtion. Ventilation in the early, days of coal mining was accomplished by means of a natural draft, created principally by a difference in the weights of columns of air between the intake and return openings: Later the furnace was introduced for the purpose of increasing the quantity of air in circulation. Mines continued to become larger, their output increased, men were employed in greater numbers, and more fresh coal surfaces were exposed. Coal beds near the surface, and practically free from explosive gas became exhausted, and deeper beds that liberated methane were opened as development advanced. Mechanical ventilation became necessary and was first accomplished by disc-type steam driven fans she old-.fashioned steam driven disc fan has generally been supplanted by the powerful electrically operated centrifugal fans in use at modern coal mines. In order to be secure against gas explosions and provide ample fresh air for persons employed in large coal mines, air must be conducted through the mine to all working places and to all other unsealed parts of the mince in sufficient quantities to dilute and render harmless all dangerous and noxious gases.

Jan 1, 1929

By William Rachunis

This publication describes the construction of 43.64 miles of underground tunnel to be used as an aqueduct, known as the West Delaware aqueduct. In the past, the accident history of tunnel operations has not been favorable, the "rule of thumb" being a death for each mile of progress, according to the meager accident statistics available for the tunnel-driving industry. The accident experience at this project and the use of modern equipment established safety and progress records that were accepted by tunnel people as a record at the time. The city of New York comprises 5 boroughs, with a total population of approximately 8 million people, and uses about 1,210 million gallons of water each day. The water supply for the city is the responsibility of the New York City Board of Water Supply. This organization has constructed an extensive aqueduct system, the Delaware aqueduct, to convey water to the city from the distant mountain and river sources in the Catskill Mountains in the Southern Tier areas of New York State (figs. 1 and 2).

Jan 1, 1962

By H. Murray

Introduction Industrial minerals are key ingredients in a large majority of domestic and industrial products that are used in our daily lives. In the 7th edition of Industrial Minerals and Rocks, fifty three industrial mineral commodities are described. A precise definition of industrial minerals and rocks is difficult. Bates (1975) proposed a definition which is widely used and is as follows: "any rock, mineral, or other naturally occurring substance of economic value, exclusive of metal ores, mineral fuels, and gemstones: one of the non-metallics". They can be igneous, metamorphic, or sedimentary and range in price from a few dollars per ton to a very high price of hundreds of dollars per ton. The growth in their production and use is closely allied with population growth particularly in countries that maintain a high standard of living. The United States just passed 300 million in population and it is predicted that by 2040 the population will be 400 million. This will result in large increases in the need for Industrial minerals. Other factors that relate to increased use of industrial minerals are increased research and development by the producing companies and better quality control. Many industrial minerals such as kaolin, barite, nepheline syenite, fluorspar, lithium carbonate, phosphate rock, potash, talc, and several others are exported from the producing countries to many users around the world which has significantly increased their use. Also, government agencies, State Geological Surveys, and Universities have contributed to their growth by their research and development activities.

Jan 1, 2007

By ALBERT F. J. BOARDEAUX

(Canal Zone Meeting, November. 191(j.) I. GENERAL INTRODUCTION. 1. Historical. ALLUVIAL gold was first discovered in Guiana in 1852, in the sands of the Arataye river; by Paulino, a Brazilian convict. During the following years, gold was found also in the rivers Orapu, Cirubé, etc. In 1873 the famous placers of the Sinnamary system were opened: Saint-Elie, Dieu-Merci, Adieu-Tat, and Couriége. This group of mines has produced nearly $10,000,000, according to official records, not including the gold that escaped the taxes. The discoverer was a mulatto named Vitalo. Except in a few rich spots, the gold was rather evenly distributed along the creeks. In one instance, gold was found in the red dirt from the slope of a hill, which, after transport to the creek, gave an amount of 150 kilograms. The placers of the Mana system, Enfin, Elysée, Pas-Trop-Tot, date from 1878, and their production has been about $5,000,000. In 1888, the Awa placers, along the boundary between the French and Dutch Guianas, on the Maroni and its tributaries, were discovered. They have yielded $12,000,000. The only industrial company,, the Dutch Guiana French Mining Co., produced in 15 years about 2,500 kg. of gold, worth $1,500,000. From 1893 dates the famous Carsewene discovery, in territory then in dispute between France and Brazil. A settlement was made recently in favor of Brazil, by arbitration of the Switzerland State Council. Carsewene is said to have pro-duced about $18,000,000 in six years (1894-1900), but not even one-fourth of the production went through French Guiana and

Nov 1, 1910

By Zsuzsanna Zborovszky

A circuit is considered intrinsically safe when any spark or thermal effect produced normally (that is, by operating the equipment in its correct operational manner to fulfill its purpose) or accidentally (caused by short circuit, earth fault, defective components, breaking the wiring, etc.) is incapable under prescribed test conditions of causing ignition of a prescribed gas mixture. The test conditions and gas mixture should be at least as hazardous as the true parameters of the environment where the circuit will be operated. According to present practices, the question of whether or not a circuit is intrinsically safe is decided upon experimentally. The circuit is inspected first for mechanical soundness and a survey is made to determine what faults should be considered as probable. Then the individual branches are connected, in sequence, to a test apparatus called 'breakflash" which acts as an opening, closing contact and thus draws sparks from the circuit. This test is repeated a given number of times in the presence of the prescribed gas mixture under specified conditions (electrode configurations, gas parameters, etc.). The equipment will be regarded as intrinsically safe if during testing no ignition has occurred.

Jan 1, 1972

By Louis E. Dalverny

U.S. Bureau of Mines research to develop diagnostic methods to locate and evaluate fires in abandoned mines and waste banks and techniques to extinguish such fires was applied to an abandoned 60-acre underground bituminous coal mine (Renton, Allegheny County, PA) to locate and extinguish three separated fire zones. Mine fire diagnostics interpret changes from baseline values in subsurface pressures, temperatures, and mine gas composition under imposed pressure gradients induced by a borehole exhaust fan. The effective gas sampling area surrounding each borehole is greatly enlarged. Sampling iterations, using a "communicating" boreholes set, provide "fire signature" information for locating both heated and cold areas. Time-dependent monitoring differentiates heating and cooling periods resulting from combustion front movement and/or fire extinguishment activities. A water injection with fume exhaustion extinguishment effort involved injecting water through boreholes to quench the heated zones while exhaust fans actively removed heated gases from the mine. The technique was ineffective as implemented, primarily because of inadequate spreading of water from the injection points. The Bureau's diagnostic method determined the fire locations and the effectiveness of the water injection with fume exhaustion extinguishment technique.

Jan 1, 2010

Dimension stone is the term generally given to rock used in building construction. During early European history in Otago, locally available dimension stone products were easily obtained. Crude rock shelters built on river banks with schist rock within Central Otago soon gave way to more established and sophisticated permanent homesteads constructed with the same materials. Victorian architectural achievement is celebrated in Otago with many fine bluestone block buildings. When the University Council decided to build substantially in stone, it narrowly escaped disaster. It was well known at the time that brick in Dunedin was of an inferior quality and that it soon wasted. Rev Dr Stuart said before the 1879 Commission that æthe Council had some old-world notions and liked to have the University with some architectural styleÆ. Contemporary utilisation of dimension stone is generally restricted by expense to a simple veneer. Stone products produced from Otago quarries have found ready markets in other areas in New Zealand , particularly prior to the share market crash in 1987.

Jan 1, 1992

By Renato Affonso de Lima

As colunas utilizadas para a produção de hidrogênio em fornos de reforma a vapor são submetidas a temperaturas da ordem de 900°C. Dessa forma, os aços inoxidáveis austeníticos da classe HPNb se mostram adequados, devido ao endurecimento por precipitação de carbetos de cromo e de nióbio. Sob determinadas condições de serviço, os carbetos de nióbio podem se transformar em um siliceto conhecido como fase G. A interface desta fase com a matriz austenítica é citada na literatura como local preferencial para a nucleação de danos de fluência. Sendo assim a quantificação das fases presentes é importante para a avaliação do acúmulo de danos em serviço. Diante disso, a simulação termodinâmica computacional se mostra uma importante ferramenta, para a previsão das fases presentes. Técnicas como a analise quantitativa das fases presentes por meio de imagens são consolidadas, porém demandam amostras devidamente preparadas e um alto custo de equipamentos na execução destas análises. Isto posto, o objetivo do trabalho é comparar as simulações termodinâmicas computacionais com o resultado obtido por meio de análise quantitativa de imagens geradas por microscópio eletrônico de varredura.

Oct 30, 2017

By M. F. Dunn

The objective of this work was to define jet fan performance in d variety of large cross-section underground mine applications and to develop guidelines for thin performance in open airways, dead headings, and multiple face areas. Measurements include common ventilation instruments, continuous recording remote electronic anemometers to measure air velocity, and sulfur hexaflouride tracer gas with chromatograph analysis to determine dilution rates and air recirculation. For open airways the following were determined: Large jet fans are leas efficient in smaller airways, but quite effective in larger open airways for achieving both uniformity end greater air entrainment, when inclined about 10° or elevated. For dead headings the following were determined: The jet fan must be placed against the rib of the heeding closest to the incoming airstream from the crosscut or recirculation will increase. The fan should be placed at the pillar corner to increase airflow. As the fan is moved closer inby, recirculation increases. Larger fans promote recirculation. Inclining fans about 12° improves airflow in large headings. For face areas the following were found: For panels having uncontrolled airflow, the fan should be placed in the incoming airflow, about one pillar inby, and directed diagonally across the faces. For panels having narrower rooms and controlled airflow, the fan should be placed alongside the panel side in the first room so as to direct or intersect the incoming airflow at the next entry or crosscut.

Jan 1, 1983

By Bernard Lewis

This report summarizes fundamental research and technical studies conducted by the Explosives and Physical Sciences Division of the Bureau of Mines from July 1, 1949, to June 30, 1950. It is the fourteenth of a series of annual reports whose aim has been to bring to the reader a résumé of the research results that have appeared in published form during each fiscal year under the authorship of members of the staff. These are referred to throughout the report.

Jan 1, 1951

By M. Kerr

Background- History The most significant change in mining since the late 1970?s has been the emergence of very large scale mining operations , which have been developed to ensure profitability with relatively low grade ores. These large tonnage operations have resulted in the development of larger unit sized machines in all operations of beneficiation, solid-liquid separation and dewatering. Often only a few flotation lines are installed and tonnages up to 25 ktpd and beyond are not uncommon. The increased throughputs have led to the development of circular, reactor type tank designs. The reactor cell system is the most up to date flotation cell design to utilise the principles of circular cell design. The Svedala DV mechanism was specially developed to suit the RCS machine giving good solids handling characteristics and excellent metallurgical performance. Development of UG2 ore type flotation equipment The equipment was developed and optimised by Svedala process from 1995. A higher energy specification was requested by industry. This amounted to 3kW/m3 for installed volume. Existing designs were at 1.5kW/m3. Hence various modifications were required to achieve the required power input. The first 50m3 machines were installed and developed at Impala Platinum?s UG2 circuit over a one year period. Once reliability and performance was achieved, over 300 large volume flotation cells were installed at Anglo Platinum and Lonmin operations as well. Pilot Plant Development The Impala Platinum High Energy pilot plant was commissioned in 2002 and had an installed power exceeding 5kW/m3. It was operated for over a year at the tailings dam booster station and was fundamental to the large scale scavenging plant design. All experience in overcoming mechanical and operational problems was applied in scale up design principles. A very robust mechanism was designed to accommodate the additional power input from installed motors, as well as the high SG (>1.5) of the feed source. The pilot plant flowsheet is shown in the figure below.

Jan 1, 2007

By Rubén Mattos

El presente texto señala la exploración, geología y desarrollo del yacimiento minero Toquepala, ubicado en Tacna. Este constituye un yacimiento porfirítico de cobre-molibdeno diseminado donde la mineralización está subordinada a una chimenea de brecha y a un intrusivo de dacita, ambos genéticamente relacionados a la actividad intrusiva hidrotermal calco-alcalina datada de fines del Cretáceo superior-Terciario inferior. En 1937, se inician los trabajos de prospección y exploración desarrollados en Toquepala, cuando la Compañía Cerro de Pasco ordenó una evaluación geológica, con cartografía regional, perforación diamantina y muestreo. Posteriormente se inicia la segunda etapa con estudios regionales de geología, aerofotografía, ingeniería, excavación de galerías y chimeneas exploratorias y la instalación de una planta piloto de tratamiento de minerales de cobre. Finalmente, desde 1955 a la fecha se ha desarrollado la exploración orientada a mantener las operaciones de producción de minado y expansiones planeadas de la minería.

Apr 26, 1999

By Georgios Kolliopoulos

Water is a critical commodity of our generation and a key compound for the chemical and mining industries. Sustainable industrial development is directly associated with the ability to recover clean water from contaminated sources. Forward Osmosis (FO) is a low-energy footprint membrane process allowing the recovery of clean water from high salinity effluent streams. In FO, water is recovered spontaneously into a concentrated draw solution (CDS). Energy is required to separate the recovered water from the resulting dilute draw solution (DDS). In the current work, the fundamentals of the FO process and the most important aspects affecting its performance are discussed. An energy comparison of FO and conventional water recovery technologies is presented. Finally, the opportunities FO presents in the field of hydrometallurgy are analyzed.

By B Hawkins, S Durkin, V Lawrence

The requirement for secondary egress from underground workings has long been regulated in Australia. Escape way systems have evolved from simple airleg rising ladders and timber ladders to steel galvanised ladders and more recently fully enclosed polyethylene ladders.The polyethylene ladder, Safescape Laddertube, was introduced to the underground mining industry in 2010. It is an enclosed cylindrical modular plastic ladder designed for use in underground escape ways and access ways. Since its first installation in May 2010, the Laddertube has been installed in 43 mines across four countries, totalling 8800 m of ladders installed to December 2013.The Cracow Gold mine is one operation using Laddertube, located 500 km north-west of Brisbane, Queensland, Australia. Upon discovering and developing both the Empire and Roses Pride orebodies, a safe and economically viable secondary egress system and surface primary ventilation exhaust shafts were necessary to support development and production activities to these workings. The need arose to merge these two critical requirements together between surface and underground mine workings some 200 m and 400 m respectively for each orebody. Neither egress has intermediate access points within their full service length from top to bottom. Several options were considered, the preferable and most feasible method adopted was Laddertube.The longest egress length requiring Laddertube within the two vertical surface exhaust shafts was 400 m long, within a 3.5 m diameter shaft. Due to the length of the vertical Laddertube system in both egresses, personnel are to be assisted by mechanical means using the Extended Ladder Climb Assist system.The Gossan Hill mine also uses Laddertube for their escape ways. Part of the Golden Grove operation, Gossan Hill is an underground sublevel open stoping mine located in the mid-west of Western Australia.With a considerable mine life remaining and a history of acidic water and stress related deterioration in vertical openings, the mine operators sought an escape way solution that would provide for the long-term needs of Gossan Hill. Laddertube was selected due to its non-corrosive properties and the ability to fill in around the ladder way to provide stability to the raise opening.Laddertube is a recent development in escape way systems, and is effectively being applied in a variety of operations, meeting the specific needs of underground mines.CITATION:Durkin, S, Hawkins, B and Lawrence, V, 2014. The application of Safescape Ladders at the Cracow and Golden Grove operations, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By B Wu, C Zhao, B Lei

At present, the friction factor is calculated by measuring pressure drop and airway configurations. However, the workload of on-site measurement is heavy, and the measurement results are easily disturbed by the external environment. In order to meet the need of intelligent ventilation to quickly and accurately obtain the friction resistance of roadway. Based on the important of roughness in Atkinson friction resistance formula, in this paper, fractal theory is used to characterise the 3D rough surface, and a method based on fractal dimension to describe the roughness of roadway surface and calculate the friction resistance was proposed. A computational model of friction resistance for fractal characterisation of roadway 3D rough surface was established. The parameters of the model were deduced and verified by using Nikuradse experimental data. The fractal dimension of roadway surface was calculated by 3D laser scanning data of Kailuan roadway, the established friction resistance calculation method was compared with the field resistance measurement results. It is considered that the calculation method of friction resistance based on fractal theory is reliable and can well represent the influence of 3D rough surface characteristics of roadway. The result show that the new established friction resistance formula compared with the traditional Atkinson formula in Nikuradse experimental, the average relative error is 6.874 per cent, and compared with the measured results of ventilation resistance in Kailuan experimental roadway, the relative error is 6.667 per cent. Comprehensive evaluation and analysis suggest that the new formula can well reflect the influence of 3D rough surface on friction resistance, combined with 3D laser scanning technology, the friction resistance of roadway can be calculated quickly and accurately. This research provided a reference for the key technology and theoretical development of intelligent ventilation parameter measurement.

Oct 12, 2022

By Xiao Hong, Zhang Wenqiang, Gao Bing

The characteristics of top charging coke (coke 1) and stamp charging coke (coke2) were investigated. The weight loss ratios of two kinds of cokes with and without alkalis were measured after reacting with CO under the temperature of 2 900, 1000, 1100 and 1200 °C respectively. The microstructures of original cokes were observed by SEM. The experiment results show that, with no addition of alkali, the weight loss ratios of coke 1 and coke 2 were nearly the same under the temperature of 900 and 1000 °C. While the weight loss ratio of coke 2 was much larger than coke 1 under the temperature of 1200 °C. With alkali-rich, the weight loss ratio of the two cokes was almost the same at 1100–1200 °C.

Mar 1, 2017

By J. R. Bartels

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Two sin-diameter 6x25 fiber core (FC) ropes were degraded on a bending fatigue machine, These were the second and third ropes in a series of tests on this construction and size rope. Tensile and nondestructive tests were performed on samples of the rope to determine the relationship between rope deterioration and rope breaking strength. The tests indicated that once a wire rope nears the end of its service life, both deterioration and the consequent loss of rope strength begin to increase at an accelerated rate.

Jan 1, 2010