Search Documents

By K. H. McDaniel, D. M. Loring

The underground ventilation system at the Waste Isolation Pilot Plant provides unparalleled ability to ensure safety of the workers, public and environment. Although small spatially, it can vary the airflow from 66,000 acfm to 460,000 acfm. It can automatically incorporate HEPA filtration in the event of radioactive contamination. Remote-capable regulators individually control the four main splits, and can be adjusted from the surface if necessary. A ventilation remote monitoring and control system provides real-time information. Future areas of concern include DPM compliance, system psychrometry, logic-based-real-time mine ventilation simulation and automation using PLC technology. This paper discusses the evolution of this system.

Jan 1, 2002

By R J. Johnson

The development of "SANFO" has provided the Mining Industry with a LOW COST HIGH GAS VOLUME, VARIABLE DENSITY, Blasting Agent which can be blended "On Site" in a simple Agitator mixing and charging system by mine site employees.

Jan 1, 1996

By Paul Downing

When was the last time the documents and paperwork were cleaned out of the glove boxes, door pockets, under the seats and above the visors in your company vehicles? Insurance cards that expired three years ago and vehicle registrations from 1999 through 2003, for instance, don’t do any good and just take up space

Jan 1, 2008

By Edward L. McHugh

The Thousand Lakes Wilderness has no known economically significant mineral resources. However, the geologic setting of the Wilderness indicates a potential for the discovery of geothermal resources. INTRODUCTION The Thousand Lakes Wilderness occupies 16,335 acres (6,611 ha) in eastern Shasta County, California. A mineral resource study of the area was authorized by the Wilderness Act of 1964 (Public Law 88-577). Mining records and published information were examined, and field investigations conducted in 1979. The Wilderness is about 50 miles (80 km) east of Redding and 12 miles (19 km) south of Burney, California. It lies in the Cascade Range of California. Relief is more than 3,000 feet (910 m); elevation is greatest at the summit of Crater Peak, 8,677 feet (2,645 m).

Jan 1, 1982

By F. F. von Glehn

There is no doubt that simulated ventilation networks must be adequately verified before they can be extrapolated and used for predictive purposes. There are two general approaches as to how the verification can be established and these are summarised as follows; The first approach is to measure all individual branches with trailing hoses or barometers to get individual pressure drop and flow per branch and then calculate individual resistance factors for input into the software. The simulator is run, checking that the output makes general sense (check some sensitivities if possible). The network is now considered as verified. The pressure drop to be measured is relatively small and thus it is inherent that the measured set of individual K factors will be imprecise no matter how much care is taken in the measurements and the resultant simulations will inherit the same problem. In the second approach, the network is assembled using estimated (Atkinson) K factors (based on physical features of airway, past experience and catalogued typical K factors). Only the main primary flow rates are measured and hence the relative distribution of the primary ventilation in the main airways is determined (probably about 10 off primary air flow measurements). Main critical pressure differentials at main and booster fans and across critical doors are measured (probably about 6 off primary pressure differential measurements need to be made). The simulator is run and the computer model is used to iterate and select an updated suite of K factors so that the flow balances and pressure differentials are correctly simulated (typically only 2 or 3 iterations are all that is needed). The network is now considered as verified. The pressure differences to be measured will be substantial in absolute terms and can be measured with high precision. Also, because only primary flows are measured, these will generally be measured at higher air speed points and hence improved relative accuracy. This leads to more accurate simulation results. This paper examines the advantages and disadvantages of the two approaches. 1 Background

Jan 1, 2009

By H. A. Taylor

Graphite is elemental carbon that crystallizes in the hexagonal system as six-sided platelets. It occurs naturally and is mined. And it can be made artificially from petroleum coke in the form of shapes (electrodes) and powders. The market for most kinds of graphite in most end-uses was good in 2004. The 2005 graphite market looks positive. The major graphite prices, as given in Industrial Minerals, remained unchanged throughout the year. The preliminary 2004 U.S. Geological Survey (USGS) prices for natural graphite showed almost no change for crystalline flake. They were $600/t ($544/st) in 2004 and$622/t ($564/st) in 2003. Mexican amorphous graphite was almost unchanged at $150/t ($136/st) in 2004 from$152/t ($138/st) in 2003.

Jan 1, 2005

By R. G. Aspden, D. A. Colling

THE {120}(001) texture has been reported in near 50 pct Ni-Fe alloys <0.004 in. thick1,2 and in copper 0.014 in. thick.3 This texture is one of two types of secondary recrystallization textures observed to replace a cube texture matrix and is desirable in Fe-Ni alloys because of its unique magnetic characteristics.1,2 However, the conditions for and mechanism of the {120}(001) formation are not well understood.3 During an investigation of the influence of alloying elements on the magnetic characteristics of 49 pct Ni-Fe alloys with a sheet thickness of 0.014 in., we have observed the growth of {120}(001) secondaries when strong deoxidizers such as aluminum and calcium were present. It is believed that this observation in unique and provides additional insight with regard to the mechanism for {120}(001) texture formation. Three alloys were prepared with electrolytic iron and nickel and contained a nominal 49 wt pct Ni. Alloy A was a straight binary Fe-Ni alloy, whereas intentional additions of 0.013 wt pct Ca to alloy B and of 0.59 wt pct A1 to alloy C were made. Ingots were forged at 1100 C, hot-rolled to 0.150 in. gage, pickled, and cold-rolled to 0.014 in. Standard U-shaped magnetic test specimens were punched, deburred, sprayed with MgO, and annealed in ~50°C dew point hydrogen. Textures were identified with the aid of etch pits, the

Jan 1, 1970

By ATF Publications

The following is a summary of the changes that were incorporated into the new Federal Explosives Regulations, 27 CFR Part 55, dated 9/2000. However, in light of the recent events of September 2001, additional changes in the Federal Explosives Laws and Regulations may be forthcoming. The nature and extent of any such potential changes are impossible to gauge at this time. However, this synopsis of the changes contained in the September 2000 Orange Book, ATF P 5400.7 was current at the time of this writing. Any questions regarding this paper should be directed to the Public Safety Branch in ATF Headquarters in Washington, D.C.

Jan 1, 2002

On the first of October 1991 two significant pieces of legislation came into force. Both of these are relevant to the allocation and use of minerals in New Zealand . They are the Crown Minerals Act 1991 and the Resource Management Act 1991. &nbsp; The full legal implications of these is not fully known because the Planning Tribunal and the superior courts have not as yet had to deal with them in any detail. However, the thrust of the legislation is clear and it is appropriate to give an overview of how the statutes will operate in tandem if you are seeking to pursue or oppose any prospect, exploration or mining of Crown Minerals in New Zealand.

Jan 1, 1992

By Shaw Bill

The paper describes of the JORC Code in terms its background working environment and reasons for success, and provides references to papers which cover the subject in more detail. It then discusses the two major developments in Australasian reporting standards in the last two years: the revision of the 1999 Code, and the introduction in early 2003 of the “ROPO” (Recognised Overseas Professional Organisation) initiative. The purpose of the JORC Code is to provide a minimum standard for reporting of Exploration Results, Mineral Resources and Ore Reserves in Australasia, and to ensure that public reports on these matters contain all the information which investors and their advisers would reasonably require for the purpose of making a balanced judgement regarding the results and estimates being reported.

Apr 22, 2003

By Alec C. Bloem

A 55&apos; deep excavation encompassing almost a city block in London, Ontario required a lateral earth retention system to provide both temporary excavation support and a permanent groundwater cut-off wall for a proposed office complex. The system selected was an interlocking Drilled Shaft wall with 3-4 levels of tiebacks. The specifications required the system to be designed for movements or settlements around the excavation of ¼" max. Design to be by the Contractor with design parameters and a comprehensive soils report provided. An extensive system of instrumentation in the form of inclinometers and survey targets were used to monitor vertical and horizontal movements of the shoring system and adjacent properties. Introduction The project, One London Place, is a two phase office tower development in downtown London, Ontario. Phase one consists of a 24 storey office tower on the northwest part of the site, with five levels of below ground parking over the entire site "Figure 1". A second office tower will be constructed at a future date.

Jan 1, 1991

To provide a means for accurately and reliably warning of impending roof falls or rock bursts and for evaluating support systems. The Approach: Development of a device for measuring rockbolt loads which is not affected by harsh environments nor by eccentric loading conditions and is easily adapted to various size rock bolts. How It Works: The Rock-Bolt Tension Load Cell, developed by the Bureau&apos;s Spokane (Wash.) Mining Research Center, is installed on a bolt and sandwiched between a conventional doughnut washer bearing plate and a torqueing nut (Fig. 1). As the bolt takes load, the bearing plate transmits the load axially to the cell through a ball and socket arrangement, compensating for uneven bearing surfaces. The cell body strains in proportion to the applied load: the strain is sensed by welded strain gages as change in electrical resistance. The resistance change is read through a Wheatstone Bridge and, through calibration, the applied load is determined.

Jan 1, 1974

By D Craw, J Pope, B Peake

Southland contains over 70 per cent of New ZealandÆs recoverable coal resources, and an investigation into the potential effects of coal mining on SouthlandÆs water resources is therefore of interest. This paper investigates pit-lake water quality in relation to current mining activities within the sub-bituminous coal and lignite deposits of Southland. &nbsp; Water quality data was collected from pit-lakes in sub-bituminous and lignite deposits from October 2005 to March 2006. After periods of settled weather, turbidity increased with depth at the sub-bituminous pit-lake (10 - 21 NTUs from 5 - 30 m). In the stratified sub-bituminous pit-lake in March 2006, heavy rainfall caused higher turbidity in the epilimnion than the top of the hypolimnion (20 NTU vs 13 NTU) reflecting surface water runoff (up to 1993 NTUs) and epilimnion mixing. In contrast, turbidity at the lignite sites was variable due to the shallowness of the lakes, but noticeable increases following disturbance and adverse weather were recorded. High turbidity at the sub-bituminous deposits was attributed to the presence of clay minerals such as kaolinite whereas turbidity at the lignite sites was more likely short term and a result of heavier minerals such as quartz. &nbsp; Trace element concentrations at both sites were low when compared to mine waters in other coal areas in New Zealand and no samples exceeded ANZECC water quality trigger values for 80 per cent species protection. Pit-lake water pH levels were lower and more variable in the lignite deposit (4.18 - 7.30 vs 7.24 - 8.98 in the sub-bituminous deposits). In the lignite pit-lakes, higher concentrations of trace elements (eg Dissolved As - 0.034 ppm and Dissolved Mn - 1.09 ppm) and lower pH (ÿ4) were observed at the bottom of active pits compared to inactive pits. It is possible that quartz pebble conglomerates containing sulphide minerals within the lignite seams are responsible for this. &nbsp; Further investigation into the mine waters, waste rock and lake sediments will help get a better understanding of the results observed and long term processes that occur.

Jan 1, 2006

By Seoul National University, Ki-Ho Kim, Jong-Pyo Kim, Sung-Min Joo, Hee-Chan Cho, Hyung-Seok Kim

Aragonite was synthesized in addition of Mg2+ ion and SrCO3 seed by carbonation process, and the best condition and mechanism of the synthesis was studied by analysis of continuous pH change, ICP, XRD, and SEM. As MgCl2•6H2O addition increased, aragonite phase increased at condition of CO2 flow rate of 100 mL/min and stirring rate of 250 rpm. It was the dissolution of Mg(OH)2 that determined overall reaction time. As SrCO3 seed addition increased at 0.2 mole MgCl2•6H2O, the amount of aragonite increased and the aspect ratio was from 5 to 9. And it was thought that Mg2+ ion prohibited calcitetransformation of aragonite formed by SrCO3.

Jan 1, 2003

By Ann Barron

For millions of people, cold weather is a fact of line – and one that can make a major challenge out of just getting to work. But for those working in the blasting industry, a number of obstacles are created when old man winter blows in. In addition to the obvious concerns regarding personal protection, Mother Nature can throw some very nasty weather at the blasting crew trying to travel with explosives products from the magazine site to the job site. As such, divers need to be familiar with cold, ice, and snow driving conditions both on and off the blast site. It’s critical to know what to expect before you leave. Keep informed of the latest weather and road conditions as they change often; it will help you make the right choice in clothing and driving habits. Remember bridges and overpasses will freeze first even in temperatures above or near the freezing mark due to the effects of wind chill. Plan to take extra time to and from the job site.

Jan 1, 2004

By George K. Burke

Single axis soil mixing is a mechanical method of blending soil in situ with a reagent binder to achieve improved character. Generally this achieves a design compressive strength or shear strength and/or permeability, but can be used to immobilize and/or fixate contaminants as well as a treatment system for chemical reduction to a more "friendly" substrate. The reagent binder can be a variety of materials, including cement, fly ash, slag, lime, and an assortment of additives. Usually this reagent is delivered in a slurry form (combined with water), but the Dry Mix Method uses pneumatic conveyance.

Jan 1, 2001

By Michael J. Jorgensen, Anoop Polsani, Khurram S. Khan

Riveting operations in aircraft manufacturing involves the use of power tools for manually drilling holes for the rivets, power drills for the setting of the holes for the rivets, as well as rivet guns to drive and set the rivets. To close the rivet, the rivet is driven against a metallic bar commonly called a “bucking bar”. The bucking bars are typically held firmly to increase the quality of the riveting, as well as keep the bucking bar from “dancing” against the metal piece being riveted. Thus, employees in aircraft manufacturing involved in riveting are exposed to hand-arm vibration from several sources, and epidemiological evidence suggests that vibration-related musculoskeletal disorders are associated with long term exposure to riveting tasks in the aircraft manufacturing of aircraft.1,2 Recently, tungsten technology has been introduced into aircraft manufacturing for bucking bars, which are heavier than traditional steel bucking bars of the same size. Rivet guns with tungsten pistons instead of steel pistons have also recently been introduced with the objective of reducing vibration exposure to the riveter. The objective of this study was to assess vibration characteristics of steel and tungsten bucking bars and rivet guns to identify the combination that simultaneously reduced the combined exposure to both the “riveter” and “bucker”. Methods Vibration (10g tri-axial accelerometer, Biometrics S2-10G-MF Series 2) was measured from eight experienced employees using seven different rivet guns on size 6 rivets, with the same person bucking for all subjects. Vibration was also measured on two different bucking bars for these same eight subjects, with the same person driving the rivets using the various rivet guns. The rivet guns consisted of three E4 steel piston guns with different RPMs (Guns A-E4, B-E4, C-E4), an E4 vibration dampened rivet gun (Gun D-E4D), an E3 steel piston rivet gun (Gun E-E3) and an E3 and E4 tungsten piston rivet guns (Guns F-E3T and G-E4T). The bucking bars were made of 90% tungsten (1694g) and cold-rolled steel (843g), and were the same shape and size. A two-way repeated measures analysis of variance was performed on the vibration (mean frequency weighted resultant acceleration) on both the rivet gun side and the bucking bar side, and mean rankings were used to assess the vibration simultaneously for the rivet gun and bucking bars to investigate which combinations provided the lowest vibration exposure. Results Frequency weighted resultant acceleration was significantly lower on the E3 tungsten (F-E3T) rivet gun than the E4 steel piston (B-E4) and the E4 tungsten piston (G-E4T) rivet guns (Figure 1). When measuring vibration on the bucking bar, the E4 (A-E4) steel piston rivet gun resulted in lower vibration on the bucking bars than the E4 tungsten piston (G-E4T) and E4 vibration dampened (D-E4D) rivet guns (Figure 2). Additionally, use of tungsten bucking bars resulted in a 35% decrease in resultant frequency weighted acceleration than when using steel bucking bars.

Jan 6, 2006

By C. K. Kocsis

A study was undertaken to evaluate the thermal environment and determine the contributing heat sources within the existing 153 Orebody of Coleman/McCreedy East Mine which would then enable the prediction of the climatic conditions in the mine?s future 170 Orebody. The study entailed continuously monitoring, for a 2-week period, the dry-bulb temperature, humidity and barometric pressure along the existing intake airways from surface down to the 4810 Level and throughout an active mining area on that level. Furthermore, the mining activities and associated equipment that could be responsible for any changes in the temperature and humidity conditions within this mining area were also monitored. These data were then used to develop and validate a climatic simulation of the mine?s mechanized cut and fill mining method. This climatic model was then transposed to the future 5700 Level in the deeper 170 Orebody, to determine the environmental conditions within its production workings and along the main haulage route ascending from that area. Based upon the simulations performed it was shown that the level of ventilation planned for the new orebody should be able to maintain adequate environmental conditions. However, this study did emphasize the importance of the appropriate distribution of airflow in workplaces that used auxiliary ventilation in order to sustain a suitable thermal environment.

Jan 1, 2009

Laboratory testwork was carried out on an overall orebody composite, of 2.9 per cent Cu and 4.2 per cent Zn, prepared from drill core taken from the Currawong fine-grained, copper-zinc massive sulphide deposit near Benambra in Victoria. While 90 per cent of the copper was readily recovered in a concentrate of 20 per cent Cu, after grinding to 95 per cent passing 38 microns, zinc responded poorly to conventional flowsheet/reagent regimes. Experience elsewhere with the use of reverse cleaning, to separate pyrite from sphalerite, led to a series of tests in which better (but still modest)metallurgical results were obtained. The best result was a zinc recovery of 55 per cent in a concentrate of 50.5 per cent Zn. The major loss of zinc occurred in the reverse cleaning stage where the unit recovery of zinc was similar to pilot plant results achieved at Mount Isa Mines on similar feedstock. Diagnostic mineralogy suggested that an overall zinc recovery of 70 per cent was probably the practical upper limit, at a 50 per cent Zn grade.

Jan 1, 1999

By Daniel Gustavo Perucca

Los proyectos Veladero, Jagüelito, el proyecto binacional Pascua-Lama y otros ubicados en la zona Valle del Cura, provincia de San Juan, Argentina necesitan una vía acceso que permita el tránsito de camiones capaces de transportar los insumos necesarios en sus etapas de construcción y explotación. En este sentido, el objetivo del trabajo estriba en seleccionar la alternativa más conveniente y así cuantificar los costos y beneficios derivados de la construcción de un camino de vinculación entre los proyectos mencionados y las localidades de Rodeo o Las Flores. La metodología aplicada es la comparación entre costos y beneficios entre las situaciones “con proyecto” (obra ejecutada) y “sin proyecto” (situación actual), de forma que en un futuro, la construcción del camino estudiado posibilitará el abastecimiento de insumos a los yacimientos ubicados en el Valle del Cura, provincia de San Juan.

Sep 13, 2001