Search Documents

By X. Yu

Although many investigations of the deformation behaviour of rocks have been carried out, most of them are carried out in compression. In all rock engineering practice it is usually assumed that the deformation of rocks in tension is the same as that in compression. However, data from numerous researchers have shown that this assumption is not correct for some rocks. A new loading frame for testing rocks in compression and direct tension has recently been developed by the authors, with the capacity to conduct both compression and tensile tests on the same rock sample. The results obtained show that the ratios between the average Young?s modulus in compression (ECA) and in direct tension (ETA) are 1, 1.16, 2 and 6 respectively in four rock types tested. For Poisson?s ratios, analogous relations were obtained. It was observed that, in all cases, the tangent Young?s modulus intension reduces with an increase in the applied tensile stress, while the behaviour of Poisson?s ratio is similar, but shows greater variability. The difference between the Young?s modulus of rocks in tension and that in compression could lead, large errors in calculating induced stresses around underground openings, as well as in determining the Brazilian tensile strength of rocks. This may have a significant influence in rock engineering and therefore more investigation is necessary into the tensile deformation behaviour of rocks and its influence.

Jan 1, 2005

Fine Gravity Separation in the Reflux Classifier, Exploiting a High Shear Rate, Laminar Flow Mechanism The Reflux Classifier is used in the gravity separation of particles over a broad range of particle sizes. The device consists of a fluidised bed zone, with a system of parallel inclined channels above. The inclined channels provide a significant hydraulic advantage over conventional fluidised beds via the so-called Boycott Effect (Boycott, 1920). This paper describes a new advance in fine gravity separation based on the high shear rate and laminar flow profile that arises when closely spaced inclined channels are deployed. As reported recently (Galvin et al, 2009a), a powerful density based separation mechanism develops from this arrangement, suppressing the effects of particle size. In this paper we focus on two areas, firstly the application of the separator in the laboratory for batch fractionation of particles of varying size and density to determine the grade recovery curve and hence the liberation, and secondly the step change in separation performance achieved on a continuous steady state basis when closely spaced inclined channels are used. The variation in the separation density with particle size decreases significantly, and the Ecarte Probable Error (Ep) remains at low levels over a broad size range.

Sep 13, 2010

By J. van Deventer

Testwork was done with two different adsorbents, Dowex-Minix gold-selective resin and activated carbon, to detemine their relative performances with regard to gold recovery from clarified low-grade solution employing a fixed-bed operation. The mill discharge from the milling-in-cyanide operation at a Witwatersrand gold mine was used as feed to the adsorption columns. A small amount of gold was leached during the milling process, so that this solution simulates, to a certain extent, a low-grade solution representative of a heap-leach operation. A speciation of the feed solution was done to establish which metal complexes were present in the milling-in-cyanide solution. This information was necessary to interpret metal loadings on the resin, as base metal cyanide species and their respective charges have an effect on the final gold loading capacity of the resin. Equilibrium isotherms were established for both adsorbents to estimate the rate of adsorbent flow anticipated for this specific feed solution. Breakthrough profiles were obtained at two different superficial linear velocities for each adsorbent. Mass transfer zone heights determined from the test work and the elution/regeneration time requirements were used to size a 150 m3/h full-scale plant for both adsorbents. A counter current configuration of adsorption columns, using three columns, should be suitable to recover gold effectively and to produce an effluent with a gold concentration below 0.01 mg/l. Based on the results obtained from the breakthrough tests, a preliminary techno-economic comparison was done between the resin-in-solution and carbon-in-solution options for the recovery of gold from low-grade solutions. This study indicated that the capital expenditure for a carbon-in-solution plant would be about 33 percent higher than that of a resin-in-solution plant. The operating expenditure for a resin-in-solution plant is expected to be only 60per cent of that for a carbon-in-solution plant. Keywords: resin-in-solution, carbon-in-solution, heap leach.

Jan 1, 2000

By A. Moss

The Palabora Mining Company has successfully extended the life of its operation by developing a 30 000 tpd block cave underground mine below the now closed open pit. The process of transitioning from surface to underground mining has been technically, operationally and managerially challenging. This has been due to a number of factors, in particular, the development of a block cave in a very competent rock mass. The competence of the rock mass is clearly demonstrated in the open pit that preceded the block cave, one of the steepest deep open pit excavations in the world. With cave breakthrough, however, the pit was ?instantaneously? deepened by 400 m causing a major failure of the north-west wall involving close to 100 Mt of waste material.

Jan 1, 2006

By S. W. Stogran

"A brief summary of the environmental testing and analyses required to ensure and maintain compliance of mining properties will be discussed. Programs for new and existing properties and for properties which may be purchased will be outlined and potential solutions to problems will be discussed. In addition to the compliance aspects of operations, due diligence will be discussed.1.0 INTRODUCTIONThe impact of mining projects on the environment is an area of major concern to the public, governmental agencies and mining companies. Due to the ever increasing pressure on the government by special interest groups and the public, governments have implemented legislation to control potential environmental impact of mining, from the exploration phase through to close-out. By not planning for environmental issues during all phases of a mining operation, unavoidable delays and retrofitted environmental programmes will be expensive and cause projects to be delayed, which, ultimately, may cause the abandonment of a mining prospect. Most jurisdictions require at least one full year of background environmental data. Therefore, many thousands of dollars are wasted as construction is interfered with or held up due to data collection. This may be avoided by a thousand dollars worth of sample being collected and analyzed early in the project."

Jan 1, 1992

By Richard A. Winters

There are no producing or developing mines or active mining claims in the Deschutes Canyon RARE II study area. Only two prospects were found; they have no identified potential for mineral resources. Thin diatomite deposits occur in the Pliocene Madras Formation. Development of sand and gravel deposits in the area could not favorably compete with similar deposits in the surrounding area which are closer to points of use. By mid-1982, active oil and gas lease applications covered about 25 percent of the area, a reduction from nearly 100 percent in early 1981. No holes were drilled for oil and gas exploration. INTRODUCTION Personnel of the Bureau of Mines, Western Field Operations Center conducted a mineral investigation of the Deschutes Canyon RARE II area during the summer of 1982. The area, about 10 mi (16 km) southwest of Madras, Oregon, covers 10,890 acres (4,407 ha) in the Crooked River National Grasslands (fig. 1). The Deschutes River has incised a deep canyon into the north sloping elevated lava plain near the transitional boundary of the High Lava Plains and the Deschutes-Umatilla Plateau geomorphic divisions (Baldwin, 1964, p. 20).

Jan 1, 1983

By L J. Ingle, K L. McPhee, A G. Hunt

Iron Road Limited (IRD) is currently developing the Central Eyre Iron Project (CEIP) at Warramboo on the Eyre Peninsula, South Australia. The project consists of a 30 year open pit mine, magnetite processing facilities, standard-gauge railway and deep water, Cape class capable port. Major South Australian government approvals have been received and funding arrangements confirmed.The 4.5 Bt Mineral Resource (3.7 Bt Ore Reserve), the largest in Australia and among the largest globally, is to be mined to produce 24 Mt/a high-grade, 67 per cent Fe, magnetite concentrate. This in-demand, premium product has a P80 of ~100 µm, suitable for both direct sinter feed and an additive in pelletising.The extensively drilled, homogeneous orebody is unique in both geology and mineralogy; only averaging 15 per cent Fe yet coarse-grained with almost negligible phosphorus and sulfur content. This has allowed significant opportunities to tailor the mining method to the orebody, utilising both optimised blasting as first stage comminution, as well as in-pit crushing and conveying (IPCC) to reduce the heavy haulage diesel fleet and optimise the pit shell.Approximately 1 Mt/d of total material, ore and waste, is required to be moved from the pit daily, introducing materials handling challenges, overcome by a flexible IPCC set-up, multiple overland conveyors and an exacting mine plan. Non-conventional waste and tailings storage is utilised to allow for significant water savings, progressive rehabilitation and minimisation of land impact.The processing facilities utilise both the magnetic and density properties of the magnetite to beneficiate the ore. The coarse-grained nature of the ore is exploited to minimise comminution yet still liberate a high quality product. Utilisation of modular construction methods allows risk reduction during construction and reduced pumping requirements during operation.This paper highlights the uniqueness of the CEIP, with focus on the mineralisation of the orebody, and the beneficial impacts this has on both the proposed mining method and processing. Magnetite mining is not new and IRD has used the learnings of others, and input from various vendors and industry experts, utilising knowledge and expertise to engineer an innovative, yet supported, project design.CITATION:McPhee, K L, Hunt, A G and Ingle, L J, 2017. The Central Eyre Iron Project – developing a new iron ore mine in a challenging climate, in Proceedings Iron Ore 2017, pp 613–620 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The only significant iron ore deposit in Hungary could be found in Rudabánya. The mine was closed in 1986. The area of Rudabánya was always the home of heavy mining activity. In former times, mainly silver and other non -ferrous metals were excavated.

Jan 1, 2011

By H. L. Jessberger

In recent years piled raft foundations of multi-storey buildings on weak soils have generated much interest and discussion. By taking account of the effects of each component of the system - the pile group and the raft - it is possible to reduce the settlements and inclinations of the system and to have an expedient load distribution on the piles and the raft. Thus the structural design of the foundation can be optimised.

Jan 1, 1991

By T. S. Seleka

Laser surface melting has been conducted on a 304 stainless steel (SS) with the aim of enhancing pitting corrosion resistance of the material. This process involves rapid melting of the material?s surface followed by rapid solidification to refine the microstructure. This includes the dissolution of inclusions such as MnS, FeS, CrxCy, and other minor constituents. The microstructures as a result of laser treatment were observed by means of optical microscope and also confirmed by the XRD. The glow discharge optical emission spectroscopy (GDOES) was utilized for chemical analysis. Changes in hardness were observed by using a Vickers microhardness tester. Pitting corrosion tests on laser treated and untreated samples were conducted according to ASTM G48-92 to evaluate mass loss and pitting morphology. Laser surface melting improved the pitting corrosion resistance of this material in a chloride-containing environment.

Jan 1, 2007

1. Domestic Production and Use: In 1984, 12 companies operated 27 primary aluminum reduction plants, with 3 firms accounting for 57% of production. Washington, Oregon, and Montana accounted for 35% of the production; Indiana, Kentucky, Missouri, and Tennessee 25%; Alabama, Arkansas, Texas, South Carolina, and North Carolina 20%; other States 20%. Based on published producer prices, output of primary metal in 1984 was valued at $7.2 billion. Aluminum consumption by 25,000 firms was centered in the east-central United States. Packaging accounted for an estimated 35% of domestic consumption in 1984, transportation, 20%; building, 18%; electrical, 9%; consumer durables, 8%; and other uses, 10%.

Jan 1, 1985

By Ernest Baafi

A simulation model RoadSIM using the ARENA modelling system has been developed to evaluate roadway development options for a given development panel configuration. The RoadSIM simulation system has provisions for variability/randomness in operations including cutting and loading at the face, tramming and discharge of coal to the boot end and availability of equipment. The modelling system provides a means for assessing the operational limitations of roadway development practices at a particular coalmine. It is a ?what if? tool that allows a range of equipment, configurations and operating practices to be assessed in terms of achievable advance rates and equipment utilisation. Output from the system is in the form of a dynamic visualisation as well as summary reports and detailed logs of operations over time.

Oct 1, 2009

By J. van Lookeren

In the case of a reservoir where the oil underlies a large gas cap and overlies bottom water, production can be inzproved considerably if wells are perforated below the water-oil contact rather than opposite the oil-bearing section. The theoretical arguments for this improvement, which in some cases may be tenfold, are supported by experimental evidence. INTRODUCTION Reservoirs frequently consist of one sand body containing an oil layer underlying a thick, gas-bearing section and overlying bottom water (Fig. 1). Wells in such reservoirs are customarily opened up opposite the oil-bearing interval or, rather, opposite the lower part of this interval (Fig. 2). More often than not, it is inefficient or prohibited to blow off large quantities of gas with the oil. This im-psses a severe limitation on the drawdown, which results in low oil-production rates. Because of the small difference in specific gravity between oil and water, the latter will easily cone upwards, so that the production of water together with the oil is not prevented by this completion method. In such a situation wells should be opened deeper, in the originally water-bearing zone. The gas can be shut off by not perforating over the upper part of the interval (Fig. 3) or by a tubing hung close to the bottom of the interval (Fig. 4). Initially much water will be produced, but when steady-state conditions have been established (as depicted in Figs. 3 and 4) larger drawdowns are permissible than in a conventionally completed well, and correspondingly higher oil-production rates will result. Water cuts are only slightly higher because of the small effect of gravity on the water-oil flow distribution. CALCULATIONS The ratio of improvement has been estimated by means of approximate calculations. The completion depicted in Fig. 4 is the most convenient basis for these calculations. By postulating that vertical flow gradients can be disregarded, the Appendix shows that the well-known Dupuit formula can be obtained except for some complication due to the presence of two fluids rather than one. The Appendix makes the reasonable assumption that, for suitable boundary conditions, the oil layer occupies a constant fraction of the total fluid height throughout the reservoir. The oil- and water-production rates can thus be related to the liquid levels in the borehole as follows:

Jan 1, 1966

By William R. Yernberg

The 2002 Arizona Conference was held Dec. 8 and 9, 2002, at the Doubletree Hotel at Reid Park in Tucson. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together once each year to discuss the status of the industry. The meeting featured a keynote address, a distinguished lecture and about 30 technical papers. As was the case at the 2001 meeting, the economy, the price of copper and foreign competition continue to be the hot topics of discussion among the attendees. The domestic copper industry still faces challenges due to low copper prices dictated by the world market and because of a weakened domestic economy. There continues to be concern about the Arizona region’s copper industry in light of the mergers, downsizing and shutdowns that have occurred during the past several years.

Jan 1, 2003

By A. W. Breed

The bioleaching of arsenopyrite, the oxidation of arsenate and the precipitation of ferric arsenate are competing reactions, hence their rates depend on the relative concentrations of the respective species, and the activity of the bacterial culture. Bacterial arsenic resistance may be attributed to the Pst+Pit-mutation and an energy dependent efflux pump. Pst+Pit-mutations result in a reduced uptake of arsenate. This enables the bacteria to survive in solutions in which the arsenate concentration is significantly higher than the arsenite concentration. However, the excretion of arsenate requires energy. Therefore, in the absence of an energy source or during periods of reduced bacterial activity, the inhibitory effect of arsenate may manifest at concentrations to which the culture has been adapted. The chemical ferric leaching rate of pyrite and arsenopyrite decrease with a decrease in the solution redox and may be described using a modified Butler-Volmer equation. The bacterial ferrous-iron oxidation kinetics of L. ferrooxidans also depend on the redox potential, and can be described using a Michaelis-Mententype model modified to account for both temperature and pH. A model developed using the independently determined ferric leaching, and ferrous-iron oxidizing kinetics, has been shown to compare well with the experimental data for the continuous bioleaching of pyrite. Keywords: Leptospirillum ferrooxidans, arsenopyrite, bioleaching, sulphide minerals ferrous-iron oxidation kinetics, ferric leaching kinetics, redox potential

Jan 1, 2000

Evaluation of the Iron Blast Furnace Process using Heat and Material Balances of the Flame-Zone

Sep 13, 2010

By T. Lux, M. Hanel, Degel, A. Filzwieser, R., H. Joubert

It is the increasing demand for an economic and cost saving operation mode that requires effective cooling in order to achieve low refractory wear and good furnace lifetime, which is making cooling technology an important aspect of furnace operation. In addition, the requirements for safety are getting more and more into focus. However, the use of water—today’s standard cooling medium—has major drawbacks as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion. Not to forget the severe risks for the operators as well as economical damage in case of a malfunctioning water cooling system. With this new and patented cooling technology ILTEC and the ionic liquid IL-B2001 as the cooling medium, it is possible to realise a water-free cooling solution and therefore the door is wide open to rethink existing and conventional cooling solutions. Furthermore, there is also the chance to recover heat from the process in a more efficient way. However, since the technology is novel and unique there are a lot of concerns and doubts regarding safety for plant operators and employees. The paper is intended to cover both: highlighting the enormous potential of the technology but also to eliminate concerns mainly caused by rumour and unawareness. INTRODUCTION All of us are aware of the risks when water is used as a coolant and placed in the vicinity of the liquid metal phase. Unsuitable design solutions or wrong operation modes of the furnaces or failures of refractories can cause a direct contact of water with liquid metal. The consequences can lead to equipment failures, vessel destruction but even worse to injuries and even fatalities. Over the past decades, countless incidences were reported. Fatal accidents caused by water coming into contact with liquid metal happen every year (Oterdoom, 2014; Filzwieser, Konetschnik, Filzwieser, Wallnerm & Preiss, 2014). With the novel ionic liquid cooling technology virtually all negative effects of a water cooled system regarding safety are eliminated and even additional benefits can be provided (Voermann, Ham, Merry, Veenstra, & Hutchinson, 1999;Verscheure, Kyllo, Filzwieser, Blanpain & Wollants 2006; Wallner, Filzwieser & Kleicker 2006). The fact that no explosion occurs when IL-B2001 gets in contact with molten metal results in a revolutionary solution for the metallurgical industry in terms of safety—new safety standards can be achieved.

Jan 1, 2019

By Patrick M. Y. Waye

As mines utilise more automation in mining operations to improve efficiency and safety, a corresponding increasing demand is placed on the transport of information. Some of the recent technological advances in underground telecommunications are described for various data, voice and video applications. In particular, two new innovative underground communication systems are described, one with high speed data at 30 Mbps and the other for mine wide evacuation and safety applications. The high speed data system incorporates stateof- the-art data networking technologies and the existing leaky cable narrow band radio channels. The new system provides over the same basic infrastructure the high speed data network at 30 Mbps TCP/IP Ethernet with 100 Base-T interconnection, plus 32 narrow band radio channels. The second system is a system for mine wide evacuation with "through the earth" communication infrastructure. Emergency situation can be communicated to and from all the miners within seconds through a central control location. The technology involved does not require leaky cable or any other similar transmission media installation. Many applications are possible, including warning miners of emergency situations, mine rescue operation to communicate with trapped miners, regular reporting from miners working alone.

May 1, 2001

By R. S. Fukuhara, M. J. Allan

"Highmont, a wholly owned subsidiary of Teck Corporation, operates a 25,000 ton/day mine and concentrator located in the Highland Valley of British Columbia. Construction of the plant commenced in the spring of 1979, and production from one grinding line began in late December 1980. The second grinding line began production in March 1980.The ore body consists of two main zones, the east and west pits, containing 134 million tons of ore, averaging 0.26% Cu and 0.27% Mo. Mineralization consists mainly of chalcopyrite (2/3), bornite (1/3), and molybdenite.The concentrator design incorporates an A-B-C grinding circuit (auto mill ball mill - crusher), followed by bulk flotation, copper-moly separation and leaching for moly concentrates. The two grinding and bulk flotation circuits are parallel and independent. Concentrate storage is provided between bulk flotation and copper¬moly separation and also ahead of molybdenite leaching. The plant design has been previously described in some detail. (""THE HIGHMONT CONCENTRATOR"" by C. V. Sibbald, CIMM Bulletin, March 1981).This paper will outline some of the problems associated with the construction, startup and early operation phases of the concentrator. The objective is to help others avoid some of the potential pitfalls by outlining those areas where problems occurred, or where things went well. Criticism of design or equipment is not intended."

Jan 1, 1982

By William R. Yernberg

The early part of the decade was marked by world-wide problems and economic difficulties. In 1980, President Jimmy Carter ordered the failed military mission to rescue hostages in the U.S. Embassy in Iran, Mt. Saint Helens, WA erupted killing 60 people and the Soviets and Mujaheddin guerrillas clashed in Afghanistan after the Soviet invasion. Later in the year, Ronald Reagan was elected president, defeating Carter. The first launch of a space shuttle (Columbia) occurred in 1981. Also in 1981, the first IBM-PC’s begin to roll off the lines. In 1982, Argentina invaded the Falkland Islands and Mexico’s economy was in collapse. In 1980, the U.S. unemployment rate stood at 7.1 percent, and by 1982 the rate increased to 9.7 percent. 1980 marked SME’s first full year in its new office building in Littleton, CO. The new facility was dedicated in November 1979. Claude L. Crowley was executive director of SME in 1980 and remained in that position throughout the decade. SME’s membership stood at about 26,000 throughout this period (1980-1982).

Jan 1, 2007