Search Documents

By Kodi Ranga Swamy, N. Sankar, M. Akhila

"Until recently, liquefaction-related studies concentrated on clean sands believing that only sands are susceptible to liquefaction. However, a few earthquakes like 1976 Tangshan earthquake, the 1989 Loma Prieta earthquake, the 1999 Kocaeli earthquake, the 2010 Chile earthquake, and the 2011 Christchurch earthquake, etc. showed that sand with fines could also liquefy. The research findings on liquefaction of silty soils are limited, and several structures constructed on such soil deposits are damaged during the past earthquakes. Some previous results of research on earthquake events show an increase of liquefaction resistance in silt soils with increase the fines content, but some report the opposite trend. This study presents the results based on undrained triaxial cyclic tests which were carried out on the fine sand with fines (0%, 10%, 20% and 40% fines). The samples were prepared at the required unit weight (Dr = 50%) and saturated by using back pressure and cell pressure increments. Each consolidated sample is subjected to cyclic loading with sinusoidal wave load form at a frequency of 1 Hz. The liquefaction resistance is evaluated in terms of cyclic stress ratio required to cause 100% pore pressure or 20% failure strain occur at 15 numbers of load cycles. Results are presented in forms of pore pressure build up and axial strain propagation plots. As the fines content increased, an increase in liquefaction potential was observed.INTRODUCTIONLiquefaction and related phenomenon have been responsible for tremendous amounts of damage all around the world. In general, the liquefaction may occur in fully saturated sands, silts and low plastic clays. When the saturated soil mass is subjected to seismic or dynamic loads, there is a sudden buildup of pore water within a short duration, and it could not dissipate which leads to reducing the effective shear strength of soil mass. In this state, the soil mass behaves like a liquid and causes large deformations, settlements, flow failures, etc. This phenomenon is called soil liquefaction. As a result, the ability of soil deposit to support the foundations of buildings, bridges, dams, etc. is reduced. Liquefiable soil also exerts a higher pressure on retaining walls.This lateral movement of soil could cause settlement of the retained soil. A sudden build-up of pore water pressure during quake also triggers landslides. Liquefaction damages of structures are commonly observed in low-lying areas near the rivers, lakes, and oceans."

Jan 1, 2017

By T. J. Kolokoto

This paper is based on a project conducted at Khomanani 2 shaft, Anglo American Platinum Limited. The main objective was to find an alternative support element in stopes to address the falls of ground (FOG) problem experienced at this shaft. Literature review was the major method used in the investigations. Resin bolts or any 1.5 m in-stope roofbolts were considered. The shaft was making use of 0.9 m long friction bolts, and these could not prevent the FOG experienced. Observations indicated that the FOG resulted in fall-out thicknesses averaging to 1.1 m, which is greater than the supported length of the friction bolts. The implementation of 1.5 m long bolts was recommended as a result of the project. These bolts will be able to address the fall-out thickness and provide sufficient support resistance to mitigate FOG. The chosen support element will result in a relatively small increase in support costs.

Jan 1, 2013

Operational effectiveness is fundamental to any operation, becoming highly topical in those experiencing less than optimal output from their fleets. It is all encompassing aiming to identify those factors that could be improved within production and suggesting solutions in order to optimise the existing fleet and obtain the greatest capital return on expenditure.Argyle Diamond Mine (ADM) is a large open cut diamond mine located in the East Kimberley region of Western Australia, approximately 180 km south of Kununurra. It is owned and operated by Rio Tinto on a two week on/two week off roster fly-in/fly-out from Perth or drive in/drive out from Kununurra. Through benchmarking the operation between January and June 2002, a study was undertaken allowing identification of areas falling below target. Following this, analysis of annualised hours and production downtimes were undertaken to quantify the potential gains of improvements in these areas. Strategies were then identified as stated in the 2002 mine plan, in operational effectiveness meetings, and by staff members. This project aimed to maximise direct working hours through determination of the main issues hindering performance. External and internal factors were considered and a continuous improvement program (CIP) was developed. The CIP aimed at internal site-based improvement teams to identify and implement solutions for improvement on a day-to-day basis.

Jan 1, 2003

The results of precious metal exploration carried out by Amoco Minerals New Zealand Limited over EL 33-137 in the Longwood Range, Southland, are described. Widespread gold and platinum in alluvial deposits on the perimeter of the range and anomalous gold in stream sediments on its southern and south western flanks indicates that the precious metals were probably derived from erosion of the mafic rocks of the Longwood Complex.

Jan 1, 1983

By S. Montes

Mineral floatability is strongly connected with mineral structure and composition. The complexity of mineral surfaces has meant that few attempts have been made to understand the effect of impurities (trace elements) on the flotation process. Zeta potential technique has been extensively used to evaluate the surface charge of mineral particles. Nevertheless, those measurements consider only an average of mineral particles surface charge. The presence of fine particles and inclusions covering a mineral may influence the local reagent adsorption process, which will ultimately be reflected in the subsequent global response of the mineral froth flotation efficiency. The current work assesses the iron oxide mineral, haematite (Fe2O3). Zeta potential and streaming potential techniques were used to determine the surface charge of fine and coarser particles of haematite. Further analysis was performed to determine the point of zero charge (PZC) of the mineral. In addition, adsorption isotherms of alkyl ammonium chloride reagents with different lengths of carbon chains were carried out. It was found haematite floatability depends strongly on the isoelectric point (IEP) value, which is affected by other mineral species present at the mineral surface. Haematite floatability became significant only at relatively high tetradecyl ammonium chloride collector concentrations (concentration greater than 4 10-4M), which does not happen with other oxides such as quartz. Unlike quartz, haematite develops a low surface charge over a wide range of pH, disabling all long-range attractive interactions between the mineral and the collector. Therefore, hydrophobic chain interaction is probably the most likely mechanism acting to promote collector adsorption and enhance further floatability. Diffused reflectance infrared Fourier transform spectroscopy (DRIFTS) was used to suggest a possible mechanism to understand the sequence of collector adsorption and the effect of trace species on it. Keywords: floatability, haematite, adsorption, electrochemistry, zeta potential.

Jan 1, 2007

Kinetic Behaviour of Solid/Solid Separation of Ultrafine Particles in Aqueous Suspension

Sep 13, 2010

By Arnold Hammons

Automated temporary roof support (ATRS) systems have been incorporated into roof bolters since the 1970?s. During roof bolting, many injuries have occurred from large pieces of draw rock falling inby the ATRS beam and tipping back into the operator?s area. Other injuries have occurred due to smaller, sharp rocks falling onto the operator?s hand and arm during initiation of roof bolt drilling. These injuries are attributed to weak immediate roof, sometimes called roof skin failure. Even though ATRS systems support the roof and provide a measure of protection against roof skin failure, additional hazards sometimes do exist immediately inby and outby the supported roof. Design innovations such as the ATRS mounted rocker pad deflector systems have been designed to improve the roof bolter operator safety. This paper will inform the reader of the hazards, machine evolution through different design solutions, and the current state of the art in preventing roof skin failure injuries when roof bolting.

Jan 1, 2009

By M. Radwan, S. Shimada, S. Z. El-Tawil, K. A. El-Barawy, Y. Miyamoto

This study presents the results of synthesizing monolithic siliconoxynitride, Si2N2O, ceramic from a mixture composed of reclaimed silicon and natural desert sand by using the nitriding combustion synthesis method. Single-phase Si2N2O powder was prepared by the combustion of a mixture composed of silicon and pulverized sand in 3 MPa nitrogen gas. The combustion reaction completed in 2 min and the combustion temperature reached 1577°C.The as-synthesized Si2N2O powder is agglomerate of fine particles with sizes < 5 µm and has various morphologies; rod-like and irregular crystals, irregular kinking, hollow crystals and grown pseudo-hexagonal prismatic crystals. Porous Si2N2O compacts (24.5–47.1% porosities) were fabricated from the synthesized Si2N2O powder at different calcia-alumina additives (5–20 wt%) by normal sintering at 1500°C for 1 hr in N2atmosphere.They showed superior oxidation-resistance at high temperatures up to 1500°C in an oxidizing atmosphere of Ar/O2/H2O(70/20/10 kPa).Near-full dense Si2N2O compacts were also successfully fabricated from the synthesized Si2N2O powder with 5 wt% oxide additives by using the spark plasma sintering at 1600°C.DenseSi2N2O had good mechanical properties (18.7 GPa Vickers hardness, 3.3 MPa.m1/2fracture toughness and 363 MPa strength) and excellent chemical and oxidation resistance.

Jan 1, 2004

By M I. Pownceby, S Hapugoda, V Nunna

Deposits of low-grade iron ores containing abundant goethite are distributed across the world. A common difficulty associated with beneficiating goethitic-rich ores is the poor liberation characteristics of the iron-bearing minerals which often contain finely disseminated gangue minerals such as kaolinite, gibbsite and quartz. Microwave-assisted heating has been proposed as an effective way of inducing dehydroxylation and associated mineral transformations in order to beneficiate low-grade goethitic ores. In this research, the mineral transformations occurring in a low-grade goethite-rich sample using microwave radiation was studied. Roasting conditions (up to 1000&#176;C and under various CO/CO2 gas atmospheres) were designed to generate a magnetic product from a goethite-rich, reject waste stream sample sourced from an iron ore processing site in the Pilbara, Western Australia. Conditions (T, pO2) for transforming the raw material from hydrated goethite to hematite and eventually to magnetite are presented. Chemical and mineralogical characterisation of the raw material and roast products were conducted using X-ray fluorescence, X-ray diffraction, optical microscopy and scanning electron microscopy techniques to identify the mineralogical and chemical changes occurring during the heat treatment. Further steps are suggested to optimise the microwave-assisted magnetising roasting and correlate it with the application of magnetic separation techniques to maximise the efficiency of upgrading the iron content in low-grade iron ores.CITATION:Nunna, V, Hapugoda, S and Pownceby, M I, 2017. Study of microwave-assisted magnetising roasting and mineral transformation of low-grade goethite iron ores, in Proceedings Iron Ore 2017, pp 575–582 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J Charbucinski

Commonwealth Scientific and Industrial Research Organisation (CSIRO), Exploration and Mining, has developed nuclear spectrometric techniques for borehole logging. The paper reviews the latest developments of this technology for the metalliferous mining industries. The SIROLOG logging system developed by CSIRO Exploration and Mining has been commercialised and is available to the mining industry.

Jan 1, 2000

By Jose L. Garcia

The following document aims to cover all issues concerning the three main methods employed for the in-situ survey of concrete pile integrity. Within it are described both sonic coring and low-strain tests and the frequency and time domain analysis of their results, which are the most advanced techniques currently in use in Spain. The survey techniques described were developed and began worldwide deployment in the 1960s, but it was not until the 1980s that they saw large scale implementation in Spain, largely thanks to the miniaturisation of electronics and computer equipment that made them easier to use on-site. Sonic coring, echo and frequency-response testing or mechanical impedance tests are spreading further every day. However, there appears to be a need for standardisation of the testing methods, as well as their implementation, interpretation and the presentation of results. The goal of these Spanish recommendations is to serve as a guideline for test standards and to provide examples for a correct and commonly agreed interpretation of test results, as well as settling any differences in the evaluation of defects detected in foundation works.

Jan 1, 2006

By Alexander Garcia

Roof and rib falls are the basic ground control hazards associated with underground roadways during development, stand up and, if applicable, retreat. Falls of ground can happen following the deterioration of supports or rock conditions over time, and particularly as a consequence of continuing rock deformation and/ or failure to install adequate support. Once developed, the risk of a failure is increased due to the effects of time as well as to front abutment stresses through retreat mining. The measurement of strata displacement using monitoring equipment is a form of ground control risk assessment. These monitoring systems are active, or ?live?, in a sense that risk is assessed real-time. However, there are circumstances in which falls of ground can occur without the prior recording of excessive movement. In addition, monitoring equipment is typically placed at set intervals, and strata conditions could vary between these points. Consequently, a visual assessment of other factors contributing to the risk of a fall should be made in order to complete a ground control risk assessment. Such surveys are usually one-off, thus capturing roadway conditions at one particular point in time. Ongoing deterioration is not documented through such one-time surveys, and there is a requirement for real-time or live assessment where a system is in place so that observation data can be updated on an ongoing basis, and a useful summary of prevailing roadway states produced on demand. To address the shortfalls of one-time assessments, a ?live? computerbased quantitative ground control risk assessment process has been developed. It combines visual observations processed in a quantitative manner with existing monitoring data into an interpretable output which indicates zones of roadway where there is an increased risk of a fall of ground from the roof or sides, so that remedial action can be carried out to mitigate that risk. Through improved procedures, it is now possible to generate a ground control risk assessment for each roadway, and one which can be updated frequently. This paper aims to outline and describe the assessment process.

Jan 1, 2012

By Robert J. Timko, Charles D. Taylor, Edward D. Thimons, Tom Mal

A test system was developed for measuring airflow in the National Institute for Occupational Safety and Health (NIOSH) ventilation gallery using a three-axis ultrasonic anemometer. The gallery was used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data collected at multiple sampling locations between the face and the end of the curtain were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations, and displayed as methane distribution in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within two feet of the face.

By Charles W. Merrill

Obsolescence in the mineral world is virtually nonexistent if the term is taken to mean that a mineral commodity, once established in commerce and industry, subsequently has fallen into disuse. We are living in an age of minerals. Each generation puts an increasing array of mineral-based commodities, in larger quantities, to more uses than ever before. Bastnasite, a museum mineral and a collector&apos;s item a few years ago, is now produced in quantity at Mountain Pass, Calif. Uranium, a minor byproduct of vanadium mining in the Rocky Mountain plateau area before World War 11, has grown to be a leading mineral product in several western States. And finally the total quantity and value of minerals both in the United States and in the World establish new records almost yearly. Surely the mineral industry as a whole is not obsolescent in our economy. Nevertheless, there are particular uses for particular minerals that are obsolescent and some applications have been supplanted entirely. Tin does not occupy the prominent place in foil manufacture that it once did, and the schoolboy&apos;s slate left most classrooms before the oldest of us were born.

Jan 9, 1964

By Birger Schmidt

INTRODUCTION Conceptual design of the first Exploratory Shaft (ES-I) for the Nuclear Waste Repository in Basalt (NWRB) began in July 1981; detailed design began in February 1982, and was largely completed by December (RKE/PB, 1983). The intent was to begin shaft construction by January 1983. The site had been prepared at that time, a construction manager selected and on board, the starter hole excavated and lined, and steel casings were under procurement. Government policy changed, however, and construction was halted before the drill rig started turning. Construction is now planned to begin in 1988. ES-I is a part of the site characterization program for the NWRB. The shaft will be used to develop production data and related information relative to drilling shafts at the site near Richland, WA, and to provide access to the repository horizon for site characterization and testing. The early program called for one shaft and some 330 m (1000 ft) of drifting. The program has since expanded to include a second shaft (ES-II) and more extensive drifting and testing. Currently, both shafts are planned to be 1.8 m (6 ft) in finished diameter, but studies are underway to determine if the second shaft should be larger. The drilling method was selected for shaft construction primarily because it offered a significantly shorter construction period than conventional shaft sinking using freezing and grouting. The finished drilled shaft will be lined with a continuous steel lining. Personnel are safer during construction with a drilled shaft than with a conventionally sunk shaft. The drilling method

Jan 1, 1987

During an&nbsp;eight month period, January to August 1978, nine bore holes were drilled in the Mikonui River gravels. On account of two rebores required from near bottom, the number of bores is in effect 11. Just on 1300 feet were drilled with an average depth of 120 feet. Depth varied from 102 feet to 133 feet. Penetration on average per hole value, varied from 7.4 to 16.4 feet per day. Gold values were even more erratic. Drill rig used was the Keystone churn drill manufactured locally by the Dispatch Foundary. It is skid mounted and requires a crew of two persons.

Jan 1, 1979

By Esteban D. Manrique Z.

El presente texto describe la geología estructural de la mina Pierina, Ancash, donde se resolvió los problemas geotécnicos de dicho yacimiento, producto de la geodinámica externa. Asimismo, señala los procesos técnicos ocurridos en el Neógeno durante en la formación del yacimiento como los problemas geotectónicos, de forma que obtenga un modelo geológico adecuado que pueda ser utilizado para el incremento de reservas del mineral y mejore la optimización de las operaciones mineras y se amplíe lla reserva del mineral.

Sep 12, 2011

Promoters for Soap Flotation of Phosphate Minerals

Sep 13, 2010

By Roberto J. Guardia, Ted Lewtas, Peter Rasmussen, Klaus Winkler

As part of the Lake Fort Smith Water Supply Dam Enlargement project, located in northwest Arkansas, microtunneling methods were used to install two side-by-side,1.53m (60-in) inside-diameter steel pipes between the intake structure shaft and the lake. The 46.6 m- (153 ft-) and 41.7 m- (137 ft-) long tunnels were excavated in Pennsylvanian sedimentary bedrock ranging from coarse sandstone to siltstone and shale-like claystone. The intake tunnels were constructed 18.3 m (60 ft) below lake level from the dry shaft. Special installation methods and procedures described herein were used to complete the lake taps. Installation difficulties that caused minor delays are also reviewed. After the excavation of the Intake shaft was completed, the two lake taps were installed in approximately ten weeks with the same microtunneling machine.

Jan 1, 2005

The paper outlines the history and current status of the VALMIN Code and sets out the background, methodology, results and recommendations of the Independent Review of the VALMIN Code undertaken during 2001 under the Chairmanship of Ian Goddard. The paper is based on the final report of the Taskforce, which was submitted to the Board of The AusIMM for consideration.

Jan 1, 2002