Search Documents

By D. W. Nel

Nanofiltration (NF) has attracted much attention over the past few years due to the reduced energy consumption compared to reverse osmosis (RO) and better separation performance compared to ultrafiltration (UF). Although research has been done in the area of NF of nickel ions, sodium ions, and acid separation, not much attention has been given to the separation of high nickel concen¬trations from sulphuric acid streams. The use of NF for the separation of nickel and acid from a spent nickel electrolyte is an innovative process alternative for future industrial application within a base metal refinery. In this study, the separation performance of a composite polyamide NF membrane on a spent nickel electrolyte was investigated by varying the sodium sulphate concentration in the feed (50-150 g/l), the trans-membrane pressure (35-55 bar), and cross-flow velocity (1.5-3.5 m/s), and measuring quantities such as total permeate flux, acid rejection, nickel rejection, and sodium rejection. The nickel and acid concentration in the feed were kept constant with variations between 40-60 g/l and 25-40 g/l respectively, while the temperature of the experiments was kept constant at 50°C. The membrane was found to be very selective for nickel ions, with the rejection of nickel ions varying between 54.4% and 98.2%. The rejection of acid ions varied between -5.9% and 21.8%. The rejection of sodium ions varied between 16.6% and 72.4% at a cross-flow velocity of 2.5 m/s and sodium sulphate concentration of 50 g/l in the feed solution. An increase in trans-membrane pressure increased the rejection of nickel, sodium, and acid ions, while an increase in sodium sulphate concentration decreased the rejection of nickel and acid ions. The total permeate flux was found to increase with an increase in trans-membrane pressure and decrease with an increase in sodium sulphate concentration. The cross-flow velocity had an insignificant effect on the total permeate flux and the rejection of nickel, sodium and acid ions.

Jan 1, 2013

By A. R. Kiani-Rashid

Controlled graphitization has become known as a practical method for improvement of wear resistance and machining properties in steels. In this paper, the effect of heat treatment on microstructure of CK45 steel has been investigated. Austenitising was carried out at 920°C for 5 hours. Besides, isothermal transformation was conducted at 750°C in the time range of 1-20 hours. The microstructure of the steel considerably changes by this heat treatment process which exhibits the effects of temperature, appropriate austenitising duration and isothermal transformation. Conducted experiments show a suitable distribution of semi-spherical graphite particles especially on the surface of the steel. Also, analyses demonstrate that the amount of formed graphite in the austenitising temperature 920°C is more than graphite in single heat treatment temperature of 750°C.

Jan 1, 2010

By D Lichti

This paper presents recent advancements in the MillMapper software technology, developed and used for thickness gauging of liners of cylindrical grinding mills used for mineral comminution. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces with millimetre accuracy. The paper is structured as follows. First, a review of the technology and its numerous advantages over existing techniques and the value it adds to operations are presented. These are followed by discussion of recently-implemented innovations, including improved visualisation and inspection tools, automatic ball charge volume measurement and automatic mill liner volume/weight measurement. Results from its application at several sites in Australia are presented throughout.

Jan 1, 2007

By Pengfu Tan

A thermodynamic model has been developed to predict the distribution behaviors of Cu, Fe, S, O, Pb, Zn, As, and heat balance in a lead blast furnace. The modeling results have been validated by the plant data of a lead smelter in Asia. The model can be used to predict for any set of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxygen-enriched air. The effects of the blast air, industrial oxygen, and coke charge on the distributions of Cu, Fe, S, O, Pb, Zn, As, and heat balance, and on the lead loss in slag have been presented and discussed.

Jan 1, 2005

By Nicholas G. Theofilos

The only mining activity in Belize during 1976 involved the production of construction aggregates, which were used domestically. A comprehensive ordinance regulating mineral prospecting and mining was proposed during the year. Under the ordinance, which would supersede all grants and titles, ownership and control of all minerals except petroleum would be vested in the Government. Exxon Corp. entered into an agreement with three oil companies to achieve a majority interest in nine oil prospecting leases covering 1 million acres, mostly offshore Belize. The agreement was with Weatherford International Inc. which had 30% interest in the leases, Ajax Petroleum Co. with 40% interest, and Canadian Superior Oil Ltd, with 24% interest. A new entity, Esso Ventures Inc., was established to be responsible for conducting extensive geophysical operations and drilling an exploratory well offshore Belize.

Jan 1, 1980

By C. R. Copeland

Combustion processes, comminution and materials handling can generate airborne particulates. Regulation of these particulates by the U.S. Environmental Protection Agency (U.S. EPA) is becoming progressively more stringent, and regulations will soon include ?nanoparticulates,? which are particles finer than 100 nanometers (0.1 mm). Nanoparticulates are believed to have significant negative health effects due to their high surface area and reactivity. Although it was argued that nanoparticulate concerns were only important for combustion, studies at Michigan Technological University have shown that materials handling and comminution release significant quantities of nanoparticles into the air. Laboratory studies have shown that the use of sodium metasilicate reduced airborne particles finer than 10 mm (PM10) by 86% and particles finer than 2.5 mm (PM2.5) by 80% for iron ore. Additional studies were conducted that revealed that nanoparticulate emissions were present in the types of operations conducted at pyrometallurgical facilities.

Jan 1, 2008

By BUREAU OF MINES

Mercury has been used by mankind since prehistoric times. It has been, and is now, widely used in industry and medicine and has unique properties which make direct substitution difficult or impossible. At present its prin- cipal uses are for electrical apparatus, control instruments, electrolytic soda preparation, mildew-proofing paints, pesticides, and medical and dental preparations. Deposits of mercury are less common than those of other base and precious metals, but some of the deposits are very large and have been ample to meet the world's past demands. The price of mercury has had many sharp fluctua- tions, but in general, the limited number of producers has resulted in a more stable price structure than that of many other commodities. The United States has been one of the main producers of mercury, and from 1850 to 1961 produced 3,247,704 flasks. Yearly production since World War II has varied from 4,535 to 38,067 flasks. An estimate of domestic resources of mercury producible at various price ranges was prepared for each mercury mine by combining specific knowledge of mercury mineralization with estimates of potential, based on geologic informa- tion and past production history. The sum of the individual estimates for each price range is shown in a table. A parallel estimate of nationwide production potential was made from a study of past price and production relationships. These were analyzed by plotting yearly production figures against the previous year's price, expressed in dollars of constant purchasing power. An equation was fitted to the data by mathematical means and was used to extend the curve into areas of higher than historic prices. Potential production rates at various price levels were taken from this graph. The estimated yearly production rates were used to make an estimate of total potential based on the premise that produc- tion rates and reserves have a proportionate relationship.

Jul 1, 1964

In this paper, geostatistical techniques are applied to forecast the annual copper price in the short and medium terms (from one to five years ahead). These techniques allow the incorporation of monthly and multivariate information in the analysis and provide more accurate results than traditional approaches, especially as far as the one-year forecast is concerned. A second advantage of geostatistics stems from its ability to assess the uncertainty associated with the unknown future prices, thanks to estimation variances or confidence intervals, depending on the technique used. Such an assessment has a crucial importance in decision-making, from both macroeconomic and microeconomic points of view

Sep 1, 2004

By A. Cabañas

"In this paper, geostatistical techniques are applied to forecast the annual copper price in the short and medium terms (from one to five years ahead). These techniques allow the incorporation of monthly and multivariate information in the analysis and provide more accurate results than traditional approaches, especially as far as the one-year forecast is concerned.A second advantage of geostatistics stems from its ability to assess the uncertainty associated with the unknown future prices, thanks to estimation variances or confidence intervals, depending on the technique used. Such an assessment has a crucial importance in decision-making, from both macroeconomic and microeconomic points of view. IntroductionThe copper price traded in the London Metal Exchange is a relevant parameter for defining macroeconomic policies of producing countries like Chile. It is also a key factor for the mining companies, since fluctuations in the sell price affect the expected financial flows. Due to the amount of money involved in decision-making, it is necessary to have accurate forecasts of the future copper prices and to quantify the uncertainty associated with such prices.This paper focuses on the annual copper price estimation in the short and medium terms, i.e., from one to five years into the future. Henceforth, the word “estimation” will be used as a synonym of “forecast,” according to the geostatistical jargon (Matheron, 1989).Two main approaches, based either on statistics or econometrics, are currently used to forecast commodity prices, but both of them are not very accurate when applied to copper. First, the main methods are briefly reviewed, then the geostatistical formalism will be presented. So far, the latter approach hardly has been used to estimate commodity prices, although it may reconcile both statistics and econometrics via (1) the use of a stochastic approach and (2) the handling of ancillary variables related to the copper market. Another advantage of geostatistical techniques is the ability not only to forecast the copper price, but also to measure the uncertainty associated with it."

Jan 1, 2004

By L. B. Berger

The Haldane gas-analysis apparatus used by the Bureau of Mines is patterned after the device developed by Haldane 4/ and differs from it only in structural modifications that have been added to facilitate operation and simplify construction. The apparatus was developed to permit determination of carbon dioxide, combustible gases, and oxygen with a degree of accuracy not attainable with apparatus of the types ordinarily used for the analysis of fuel gases, flue gases, and similar mixtures. The Haldane apparatus is used by the Bureau of Mines chiefly in the analysis of air samples collected in coal and metal mines and other underground workings and is applied also in the analysis of many other types of gas mixtures when accurate determination of certain constituents is desired.

Jan 1, 1938

By R. Webber-Youngman

The Department of Mining Engineering at the University of Pretoria accepts that the process of teaching and learning improvement is an ongoing exercise with the ultimate aim to deliver well-rounded mining engineering practitioners. Various challenges impact on the success of this process. An integrated and innovative process was developed and is followed in the Department to overcome these challenges. The aim of the Department is to apply a holistic teaching approach by introducing multiple integrated interventions with regards to teaching and learning strategies. Three phases of this process are discussed in this article, and are illustrated in Figure 1. During the first phase, prior to 1999, several teaching and learning challenges were identified in the Department of Mining Engineering. These challenges are discussed in the next section. In the current phase, a variety of interventions to address the challenges are being developed, implemented (in some cases piloted), and evaluated. The future phases will focus on the improvement, successes, and full roll-out of current interventions, as well as on training, development, and support for all staff members to participate in the process. (Figure 1)

Jan 1, 2011

By John M. Gomes

The preparation of tungsten carbide by molten-salt electrolysis was investigated. Sodium tungstate in the electrolyte and carbon from the graphite anode were the source materials, Optimum results were obtained with an electrolyte consisting of 83 mole-percent sodium chloride and 5.7 mole-percent each of sodium tungstate, sodium metaborate, and sodium hydroxide; a temperature of 1,000° to 1,025° C; an anode current density of 37 amp/dm2 or less; and an initial cathode current density of 150 amp/dm2. The yield was approximately 0.45 g/amp hr. The electrolytic tungsten carbide product contained approximately 5.4 weight-percent combined carbon as compared to 6.1 weight-percent for pure tungsten carbide. Microhardness of the electrolytic tungsten carbide, determined with a 50-gram load, varied from 3,480 to 3,970 dph. The material was friable and could be ground in a laboratory ball mill to less than 400-mesh particle size.

Jan 1, 1969

By K. Drescher

Excavations in deep level hard rock mines show rheological or time-dependent deformation responses to mining-induced stresses. These are generally not as dramatic as those seen in soft rock environments, such as potash and salt mines, but these deformations can nevertheless become substantial in time. It is usual to see total excavation closure at a much earlier stage than predicted by numerical models, and real-time measurements underground have confirmed that closure takes place on a more-or-less continuous basis, with highest closure rates observed after a blast and then slowly diminishing with passing time. This paper describes laboratory tests to determine the time-dependent response of hard rocks to loading, the results of the tests, and then quantifies these effects to explain the time-dependent phenomena observed underground. The primary intention of this work is to help explain the various time-dependent deformation processes around typical deep level hard rock tabular excavations. Three mechanisms were investigated in two typical hard rock types present in the deep level gold mines in South Africa, namely Ventersdorp Lava and Elsburg Quartzite. Uniaxial compression creep studies were done as the first part of the study followed by shear creep studies on discontinuities where crushed lava and crushed quartzite as well as a natural gouge were used as infilling. The last part of the study consisted of triaxial post-failure relaxation tests. The compression creep tests and the triaxial post-failure relaxation tests showed that the amount of energy dissipated by the lava is significantly less than for quartzite. For mines operating at depths greater than 2000 m the implication is that the lava must show a greater rockburst-proneness than the quartzite. Since the lava shows a lower post-failure stress relaxation, it can store sufficient energy for multiple rockbursts, which is seen in the clustering of multiple seismic events in the deep level mines. This study provides the first data available for energy change calculations in fractured rock masses, and provides the first general indications for rockburst intensities ahead of active mining faces.

Jan 1, 2003

Biosorption of Cr(VI), Pb(II) and Zn(II) from Aqueous Solutions by Immobilised Phanerochaete chrysosporium Biomass in a Fixed-Bed Column The continuous-flow adsorption of Cr(VI), Pb(II) and Zn(II) from aqueous solution by immobilised Phanerochaete chrysosporium biomass in a fixed-bed column was studied. The effects of flow rate, influent concentration of Cr(VI), Pb(II) and Zn(II) and bed depth on breakthrough curves and biosorption capacity were investigated. The experimental results showed that the breakthrough time decreased with increasing flow rate, increasing influent concentration and decreasing bed depth. The data also indicated that the equilibrium uptake of Cr(VI), Pb(II) and Zn(II) increased with decreasing flow rate and increasing influent concentration of Cr(VI), Pb(II) and Zn(II). Two models were employed to predict the breakthrough curves and to determine the characteristic parameters of the column useful for column design. The Thomas model was able to predict the breakthrough curve in the range of relative concentration(Co/Ci) higher than0.3, Cr(VI), Pb(II) and Zn(II) whereas the validity of the Bohart-Admas model was limited to the initial part of breakthrough curve at all flow rates and influent concentrations of Cr(VI), Pb(II) and Zn(II). The feasibility of reusing the immobilised fungal beads through five adsorption/desorption cycles in fixed-bed column was investigated.

Sep 13, 2010

Many states rely upon the Pennsylvania 1957 “Gas Well Pillar Study” to evaluate the coal barrier surrounding gas wells (Commonwealth of Pennsylvania, 1957). The study included 77 gas well failure cases that occurred in the Pittsburgh and Freeport coal seams over a 25-year span. At the time, coal was mined using the room-and-pillar mining method with full or partial pillar recovery, and square or rectangle pillars surrounding the gas wells were left to protect the wells. The study provided guidelines for pillar sizes under different overburden depths up to 700 ft. The 1957 study has also been used to determine gas well pillar sizes in longwall mines since longwall mining began in the 1970s. The original study was developed for room-and-pillar mining and could be applied to gas wells in longwall chain pillars under shallow cover. However, under deep cover, severe deformations in gas wells have occurred in longwall chain pillars. Presently, with a better understanding of coal pillar mechanics, new insight into subsidence movements induced by retreat mining, and advances in numerical modeling, it has become both critically important and feasible to evaluate the adequacy of the 1957 study for longwall gas well pillars. In this paper, the data from the 1957 study is analyzed from a new perspective by considering various factors, including overburden depth, failure location, failure time, pillar safety factor (SF), and floor pressure. The pillar SF and floor pressure are calculated by considering abutment pressure induced by full pillar recovery. A statistical analysis is performed to find correlations between various factors and helps identify the most significant factors for the stability of gas wells influenced by retreat mining. Through analyzing the data from the 1957 study, the guidelines for gas well pillars in the 1957 study are evaluated for their adequacy for room-and-pillar mining and their applicability to longwall mining. Numerical modeling is used to model the stability of gas wells by quantifying the mining-induced stresses in gas well casings. Results of this study indicate that the guidelines in the 1957 study may be appropriate for pillars protecting conventional gas wells in both room-and-pillar mining and longwall mining under overburden depths up to 700 ft but may not be sufficient for protective pillars under deep cover. The current evaluation of the 1957 study provides not only insights about potential gas well failures caused by retreat mining but also implications for what critical considerations should be considered to protect gas wells in longwall mining.

Jul 28, 2020

By Eduardo Lozano, Vilem Petr

This paper provides an overview of a new method for avalanche control using a high explosive charge placed at the avalanche runout zone: the case charge technique. This new avalanche control technique is well-suited to mountain roads presenting several advantages over the existing methods: minimum deployment time, low cost, reduced probability of misfires, and decreased operation time in the avalanche danger zone. The research work presented in this paper was conducted via large scale laboratory experiments where the detonation velocity and the blast physical properties were measured. During the charge design, several parameters were controlled: charge mass, diameter, geometry, density, and external confinement. In addition, the effective range of case charges was increased by the use of the Mach reflection for certain topographical situations. Finally, field test results collected by the Colorado Department of Transportation (CDOT) during the 2017 winter season are presented. The CDOT avalanche control crews have adopted the new case charge as the preferred technique in numerous avalanche locations along the Rocky Mountains roads.

Jan 1, 2018

By A. J. Hynes, Lutes. G. G., Ravenelle. J. -F.

"The Anomaly A area of the Clarence Stream gold deposits in southwestern New Brunswick contains mineralized structures that bear geometrical relationships to regional folding events. The four mineralized zones of Anomaly A (AD, MW, 93, and Murphy) are hosted by turbiditic graywacke, quartzose wacke, siltstone, and argillite sequences of the Kendall Mountain Formation. A regional scale structural analysis reflects at least four deformational events, three of which appear to control the folded geometry of Anomaly A (D2, D3, and D4). F2 and F3 folds are coaxial and are refolded into a dome and basin geometry by F4 folds. The mineralized zones are subparallel to axial surfaces of F2 folds. Structural analysis of a mineralized zone exposed at surface indicates that gold mineralization is hosted by a quartz-vein system that comprises veins generated during both D2 and D3. Threedimensional representations of Anomaly A created using drill-core data and ®GoCAD suggest that the quartz-vein system was emplaced in fault structures during D2 as well as within brecciated dilation zones during D3. Three of the four zones that make up Anomaly A have F2 hinge surfaces that can be linked through a geometry compatible with the style of F3 and F4 folds. The apparent continuity of these three zones indicates the potential for kilometer-scale mineralized structures at Anomaly A. Le secteur de l’Anomalie A du gisement aurifère Clarence Stream contient des zones minéralisées qui montrent des relations géométriques avec les épisodes de déformation régionale. Les quatre zones minéralisées de l’Anomalie A (AD, MW, 93, Murphy) sont comprises dans une séquence turbiditique composée de grauwacke, de wacke quartzitique, de siltstone, et d’argilite appartenant à la Formation de Kendall Mountain. Des quatre épisodes de déformation étudiés par l’entremise de cartographie structurale, trois semblent contrôler la géométrie de l’Anomalie A (D2, D3, et D4). Les plis P2 et P3 sont coaxiaux et sont replissés en dômes et bassins par les plis P4. Les zones minéralisées sont subparallèles aux plans axiaux des plis P2. Une analyse structurale effectuée sur une zone minéralisée exposée à la surface indique que la minéralisation aurifère est localisée dans un système de veines de quartz qui contient des veines générées durant D2 et D3. Des représentations en trois-dimensions créées avec le programme informatique ®GoCAD à partir de données de forages suggèrent que le système de veines est localisé dans des zones de failles D2 ainsi que dans des zones de dilatation associées avec D3. Trois des quatre zones qui forment l’Anomalie A possèdent des plans axiaux P2 qui peuvent être liés par l’entremise d’une géométrie qui respecte le style des plis P3 et P4. La continuité apparente de ces trois zones indique qu’une structure minéralisée pourrait s’étendre sur plusieurs kilomètres dans le secteur de l’Anomalie A."

Jan 1, 2008

By A. G. Merma

In this work, the electrocoagulation technique was studied in order to treat chemically stabilized concentrated oil-water emulsions. This study was mainly focused on the effects of operating parameters such as initial pH, current density, reaction time, electrode distance and inlet concentration on the separation of oil as measured by the chemical oxygen demand -1(COD) method. The synthetic emulsion was prepared from Shell - Talpa 30 oil (3g.L-1) and sodium dodecyl sulfate (1.0 g.L), having a Zeta potential around -70 mv at pH 8.7. The process was carried out in an electrocoagulation cell with a set of four parallel monopolar electrodes. This set consisted of two aluminum plate anodes and two 316L stainless steel plate cathodes. Kinetic curves showed that the electrocoagulation process exhibits three phases: (1) an initial phase, where the COD did not decrease because the solution had not reached the minimum amount of dissolved aluminum required to cause the break-up of the emulsion, (2) a reactive phase during which COD decreased due to possible agglomeration of the precipitates and (3) a steady-state phase where the COD did not change. The results showed that the period to reach the reactive phase decreased as the current density increased and the pH values decreased.

Jan 1, 2009

Active geothermal fields show many of the characteristics seen in hydrothermal ore deposits but there are important differences as well. There are, for example, many differences in geology and chemistry between individual geothermal fields, even some nearby, and these include variations in host rock types (volcanic, sedimentary, plutonic and metamorphic), structures controlling fluid flow (normal, lateral, and, rarely, reverse faulting occur) and hydrological setting (valleys to elevated terrain).

Jan 1, 1986

Common practice in mineral resource estimation consists of partitioning the orebody into several domains defined by grade intervals, prior to the geostatistical modelling and estimation/simulation at unsampled locations. This paper shows the pitfalls of grade domaining through a case study in which we compare the performance of several estimation schemes and demonstrate that the use of domains defined by grade cut-offs implies a deterioration of the resource estimates, mainly in what refers to precision and conditional bias. Then, several conceptual limitations of the grade domaining approach are stressed, in particular the fact that it does not account for the spatial dependency between adjacent domains and for the uncertainty in the domain boundaries. Also, this approach is shown to be sensitive to the cut-offs that define the domains, to provoke artifacts in the kriging maps, histograms and scatter grams between true and estimated grades, and to lower the kriging variance, a feature that may impact the mineral resource classification. An alternative approach is finally proposed to overcome these limitations, based on a stochastic modelling of the grade domains and a co-kriging of the grades using information from all the domains. Keywords: geostatistics, kriging, conditional bias, geological control, grade zoning.

Jan 1, 2005