Search Documents

By M. N. Shetty

LARGE copper whiskers (-100 p) of 11111 orientation were tested in a floor-model Instron testing machine, at liquid nitrogen temperature. (Testing methods will appear elsewhere.) Whiskers deformed by twinning after some initial deformation. A load-elongation curve at the onset of twinning is reproduced in Fig. 1. Twinning was confirmed by taking a back-reflection Laue picture, using a slit colli-mator, which showed distinct splitting of reflections. The tensile stress reached just before twinning is about 1.4 x 107 g per sq cm (-7.0 x106 g per sq cm—resolved shear stress) which drops to 1.2 x107 g per sq cm (-6 x 106 g per sq cm—resolved). This twinning stress is about five to ten times larger than the value for bulk single crystals of copper deformed at 77°K (-106 g per sq cm—resolved). Twinning models based on Cottrell-Bilby's pole mechanism are discussed in detail by Venables.' In the present work a mechanism based on the idea of failure of a Lomer-Cottrell barrier by recombination will be proposed. An L-C barrier may fail either by recombination or by dissociation.3 Fig. 2 provides the necessary information. It shows that the stress necessary to break such a barrier is about 1.8 x 107 g per sq cm by recombination and 4 x 107 g per sq cm by dissociation at 77°K. The twinning stress reached by whiskers is comparable to the stress level required for failure of an L-C barrier by recombination. (Stroh himself points out that his calculations should not be taken too literally.) We consider a segment of the L-C dislocation which has recombined (AB in Fig. 3) over a length to form the total dislocation which then glides in the

Jan 1, 1965

By Fred P. Giese

Southeastern reserves of titanium ores are large, widespread, and ample for anticipated demand. The leading titanium industries are mining and beneficiating sand deposits, principally in Florida, and manufacturing titanium pigments. Most of the mineral output is consumed by the producers themselves. In 1962, 20 percent of the national pigment capacity was in the Southeast.

Jan 1, 1964

By A R. Cameron

"The number of commercial explosive products available to the mining industry has been steadilyincreasing and associated with this there has been an increase in the range of characteristics or properties of them. This has lead to increased difficulties in selecting the most appropriate explosive for a particular blasting situation. Techniques are available that can be used to evaluate and compare the characteristics of explosives under a range of conditions. Also, the techniques are used to assess the variability in the characteristics between batches."

Jan 1, 1994

By B. W. Madsen

To help maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines developed a mathematical model that describes acidic ferric sulfate leaching of copper from sulfide ores. The leaching model can aid in maximizing minerals and metals recovery from primary sources by giving operators and management a better understanding of the copper leaching process. This will aid in improving dump leaching operations. The model is based on a steady-state approximation of the continuity equation for diffusion of ferric ions in the rock pores and the intrinsic leaching kinetics of the various sulfide mineral particles. Ore characteristics included in the model were ore particle-size distribution, particle shape, grade, mineral content, mineral particle size, porosity, and tortuosity. The continuity equation was used with ferric ion concentration gradients and a fixed value for the diffusion coefficient. Except for effective diffusivity, each of these factors was either measured experimentally or estimated from theoretical considerations. The effective diffusivities were determined by fitting calculated leaching curves with experimental leaching data. Vertical variations in leach solution composition and temperature within a dump are not considered in this model. The model accurately predicted copper extractions for several large-scale tests during nearly 500 days of leaching.

Jan 1, 1981

By C. Marais

The use of machine vision in the monitoring and control of metallurgical plants has become a very attractive option in the last decade, especially since computing power has increased drastically in the last few years. The use of cameras as a non-intrusive measurement mechanism not only holds the promise of uncomplicated sampling but could provide more consistent monitoring, as well as assistance in decision making and operator and metallurgist training. Although the very first applications of machine vision were in the platinum industry, no automated process control has been developed for platinum group metals (PGMs) as yet. One of the reasons is that to date froth features could not be related to key performance indicators, such as froth grade and recovery. A series of laboratory experiments was conducted on a laboratory-scale platinum froth flotation cell in an effort to determine the relationship between the platinum grade and a combined set of image features and process conditions. A fractional factorial design of experiments was conducted, investigating 6 process conditions, namely air flow rate (x1), pulp level (x2), collector dosage (x3), activator dosage (x4), frother dosage (x5) and depressant dosage(x6), each at levels. Videos were recorded and analysed to extract 20 texture features from each image. By using artificial neural networks (ANN), the nonlinear relationship between the image variables and process conditions and the froth flotation grades could be established. Positive results indicate that the addition of image features to process conditions could be used as sufficient input into advanced model based control systems for flotation plants. Keywords Flotation, machine vision, image analysis, neural networks.

Jan 1, 2011

By R Bertuzzi

This paper presents a three-dimensional analysis of a trapezoidal-shaped segmental tunnel lining for a recent tunnelling project in Sydney. Two- dimensional analyses, hand calculations and equipment selection defined the lining geometry and loads. The analysis, which was undertaken using 3DEC (Itasca), included a complete ring of six segments bolted together to assess the impact of imperfectly built rings. Asymmetry was induced in the analysis by unfavourable positioning of segments within construction tolerances. Model output includes displacement and stress within the entire ring and normal, shear and bending moments at the joints. For the case analysed, the results suggest a 10 mm construction tolerance increases normal and shear stresses along the radial joints by approximately 25 per cent and 15 per cent, respectively and up to a doubling of the induced moments.

Jan 1, 2008

By J Hall, A Gallardo, M Strizek

Mineralogy and coproponents Sino Iron, International Minerals and Austeel are in the process of developing four world class magnetite iron ore mines with multiple open pits along a 25 km strike length of Brockman Iron Formation to the south of Cape Preston on the West Pilbara coast. The close proximity of the proposed pits raises some challenging project approvals and environmental management issues relating to the impacts of dewatering at individual projects and the cumulative impacts of progressive development on local and regional groundwater resources, which includes a large fresh water aquifer system in the Fortescue River alluvium.This paper presents an outline of the hydro-environmental impact assessment process adopted and the key result that the cumulative impacts of dewatering at all four projects on the local brackish groundwater system in the basement rocks is only marginally more than the impact of any one project on its own, and that the impact on the Fortescue River alluvium aquifer is negligible. The paper also presents an outline of the proposed integrated water management approach that will involve coordinated monitoring, ongoing impact assessment and management, and reporting programs for all projects.

Jan 1, 2009

By R. L. Guerguerian

Nowadays, most grinding mills driven by a wrap-around ring motor are operating successfully. Some of the earlier problems could be attributed to the lateral stiffness and stability of their bearings. As a result, modifications to the bearings included the rearrangement of the shoes, or the addition of more shoes, closer to the horizontal centerline. This technical paper reports a study of the effects of bearings on the lateral stiffness of grinding mills driven by a wrap-around ring motor. The discussions cover the design of the four shoe trunnion bearings and examine the effects of the angular location of the shoes.

Jan 1, 2000

By S. Frimpong

The cable shovel excavator is used for primary production in many surface mining operations. A major problem in shovel excavation is the variability of material diggability, resulting in varying mechanical energy input and stress loading of shovel dipper-and-tooth assembly across the working bench. This variability has a huge impact on the shovel dipper and tooth assembly in hard formations. In addition, the geometrical constraints within the working environment impose production limitations resulting in low production efficiency and high operating costs. A potential solution to the above problems is the application of an intelligent cable shovel excavation(ICSE) technology. In this paper, dynamic models of the cable shovel excavator are developed with numerical examples. These models form the basis for developing dynamic shovel simulators for an intelligent shovel excavation technology. The dynamic equations are developed using the Newton-Euler techniques. The path trajectories for efficient excavation, dynamic velocity and acceleration profiles, and dimensioned parameters for optimum feed force, torques and momentum of shovel boom-bucket assembly are modeled and used for efficient excavation. The optimum digging forces and resistances for the cable shovel excavator are modeled and used to predict optimum excavation performance.

Jan 1, 2003

By Connie Postupack

The purpose of the workshop is to show the effect of various blasting factors on the overall results.

Jan 1, 1994

By Michael R. Walsh, John H. Wright, Eivind B. Jensen

A tunnel boring machine (TBM) was designed and built at the Cold Regions Research and Engineering Laboratory in 1992 for use in Antarctica. The TBM system was tested at the South Pole where a 120-m long tunnel was bored to prove the concept. Modifications were made to the system resulting from this work. In 1999,boring of a 600-mutilidor began as part of the new South Pole Station. Tunneler hydraulics reliability problems prevented the completion of the tunnel before the end of the short construction season. This paper discusses the design and operation of the TBM, proposed solutions to the problems encountered, and current operations of the system.

Jan 1, 2001

The Pike River Coal Company is set to develop the Pike River Coal Mine in the Paparoa Ranges of New ZealandÆs South Island. The mine will be developed to extract a coking coal deposit of the Brunner Seam, some 46 km north-east of Greymouth, using a combination of continuous miners and hydraulic extraction.   The mining area is located within Department of Conservation (DOC) land and is adjacent to the escarpment of the Paparoa Range and the Paparoa National Park. As such, the major restriction to planned extraction is protection of:   +        the western escarpment, +        vertical and sub-vertical rock faces, +        permanent water courses, +        significant vegetation, and +        steep slopes.   The mine will use its elevation advantage to hydraulically flume coal from the working faces to the pit bottom area where it will be slurried to approximately 35 per cent density of solids and pumps down a slurry line to the coal prep plant some 10.5 km down the Pike River Valley. The coal will be sold on the export market as a high quality coking coal for international steel making.

Jan 1, 2005

By E. K. Stanek

This research study was performed on a case study basis and can be divided into two parallel thrusts: electrical and thermal energy conservation. Energy consumed annually in mining and refining operations represents about 6% of the 80 quadrillion Btu's consumed nationally. In the electrical portion of the study, five areas were addressed: optimal dispatching of on-site generation, high-efficiency motors, conductor selection, power factor correction, and high efficacy lighting. In the case study mine which has a multiple unit on-site generation system, optimally dispatching units can save significant energy. The other four methods are difficult to justify on a retrofit basis due to capital costs. In the thermal portion of the study, a thermodynamic analysis was performed on the reverberatory smelting process possible areas of energy conservation were identified as radiation and convection heat losses from the furnace arch and the dumping of high energy content smelting slag. It has been shown that materials currently available can provide the means of reducing heat loss from the reverberatory furnace. It has also been shown that a significant amount of energy may be recovered from the slag. However, these are both subject to further study and validation.

Jan 1, 1982

By Rowan A' Murry Karstel

One way to ensure dragline productivity is by Increasing the size of the dragline bucket. In August 1994, Optimum Colliery in conjunction with Van Reenen Steel, Northwest Applied Technology, SSAB of Sweden and Barlows Equipment launched the new lightweight dragline buckets. Optimum built the first prototype bucket that was used for the deslgn for future buckets. After knowledge had been gained from measuring the input force of the bucket Northwest Technologies designed the new bucket with finite element analysis. Together with the knowledge of quenched and tempered steel from SSAB of Sweden and Barlow Equipment, the new Wrightech bucket was born.

Jan 1, 1998

By K. N. Panigrahi

India bestowed with 6000km of the coastal belt, contains some of the richest and largest placer deposits with a mixture of heavy minerals like ilmenite, rutile, leucoxene, zircon, monazite, sillimanite and garnet. Each of the minerals is having economic value due to its inherent characteristics for industrial use in fields of paints, metallurgy, refractory, abrasive and so on. The reserves of titanium bearing minerals (ilmenite, leucoxene, and rutile) in the country is around 378 million tonnes. More than 90% of the titanium based minerals produced worldwide are utilised for making value added products in the pigment industries. Approximately 8 million tonnes of monazite reserves are available in the country from which several rare earth elements like cerium, neodymium, lanthanum, yttrium etc. can be extracted for use in several industries. The country contains a deposit of about 20 million tonnes of zircon, which is used in foundries, refractories, ceramics and chemicals. India has a reserve of 107 million tonnes of garnet and 131 million tonnes of sillimanite required for the abrasive and refractory industries respectively. Keeping in view the multifarious uses, the beach sand minerals are being exploited to have the economic growth of the nation. Although the process adopted for the separations are simple, the equipment involved are specially designed because of the nature of the material of construction. Starting from the spirals to magnetic separators, all equipments are manufactured outside India, which is not only costly, but the availability also takes much time for fulfilling the import formalities. Unlike open cast mining, beach sand mining is a environment friendly mining because dredging is implemented to cut and pump the loose sand through a slurry pump causing less damage to the surface topography as both mining and backfilling takes place simultaneously. Therefore all out efforts are made to explore the beach sand placer deposits in an economic manner to emerge as a leader in the global mineral industries.

Jan 1, 2005

By Phil N

A large number of experiments have been carried out by many workers on the recrystallization of deformed and subsequently annealed metals and alloys. Although observations on single crystals are of great importance in the study of the recrystallization textures of deformed and annealed metals, very little of this work deals with material in this form.Since, in deformed metals, the stress concentration is greatest at the grain boundaries and along the planes of slipping, it is to be expected that recrystallization will start in these regions. For example, in polycrystalline aluminium (1),:1: (2), copper (3), a-iron (4) and brass (5), (6), which had been deformed by cold-rolling, drawing, pressing or stretching and then annealed, the new grains first appeared in the boundaries of the original crystals, whilst in the case of cupronickel (7) and iron (8), recrystallization commenced along the slip planes of the deformed material. Deformed and annealed single crystals of aluminium (9) and cadmium (10) first start to recrystallize along slip planes and in deformation twins.The present work deals with the process of recrystallization of single crystals of lead after deformatjon by creep.Two factors enter into these experiments that were not met with in other work on this subject. Firstly, lead...

Jan 1, 1940

By D. S. van Vuuren

Titanium bearing resources can selectively be chlorinated at temperatures below 200°C if the Ti02 in the feed is nitrided before chlorination. However, the nitriding reaction is highly endothermic, requires highly reducing conditions, is only thermodynamically favourable at elevated temperatures, and is affected by mass and heat transfer restrictions. At the required processing conditions, problems might also be experienced with sintering and with melting of slag forming components in the raw materials. A test programme was undertaken to study the effects of raw material type, temperature, gas composition, bed depth, carbon to raw material ratio and residence time in order to simulate conditions required for scaling up a nitriding process. In contrast to previous experience with low-grade titanium-bearing slag containing about 30% Ti02, ilmenite and chlorinateable slag do not form melting phases under the studied nitriding conditions and hardly sintered at all. Both feed materials can readily be nitrided with conversions in excess of 90% at temperatures around 1300°C and using bituminous coal as reducing agent with fixed carbon in excess of 1.1 times the stoichiometric requirement. The conversion decreases as the bed depth of the feed material increases and the N2/CO ratio in the gas decreases. Analysis of the relative rates of mass and heat transfer into the reacting beds of ilmenite and slag showed that the heat transfer rates are more limiting than the mass transfer rates. In order to increase the throughput that can be achieved in a kiln, it would be necessary to take special measures to enhance the heat transfer rates into the mass of reacting material. One such a measure is to pre-form the mass of reacting material into thin-walled, hollow brick shapes prior to introducing it into a kiln. Depending on bed depth, temperature and N2/CO ratio, required residence times in the high temperature zone of the kiln can vary between about 6 and 10 hours. Keywords Titanium dioxide, titanium nitride, carbo-thermic, reduction, ilmenite, slag, tunnel kiln, residence time.

Jan 1, 2011

By Jürgen F. Brune, Liming Yuan, Alex C. Smith

To provide insights and assistances for the optimization of ventilation systems for U. S. under-ground coal mines facing both methane control and spontaneous combustion issues, a computational fluid dynamics (CFD) study is being conducted to investigate the effect of the ventilation scheme on the prevention of spontaneous combustion in longwall gob areas. This report focuses on the flow patterns within the gob under three different ventilation systems; one-entry and two-entry bleederless systems as well as a three-entry bleeder system. The gas flow in the caved gob area is simulated as a laminar flow through porous media while the gas flow in ventilation airways is simulated as a fully developed turbulent flow. The air flow patterns are visualized using flow path lines. Air velocity contours and vector data are also obtained. The possible location of critical velocity zones where the gob is most liable to spontaneous heating is discussed.

By William D. Spielvogel

The Massachusetts Highway Department awarded the Porter Street Outfall Project to the J.M. Cashman Company in November 1991. Timely completion of the Project in one and one half years is critical to the start of the subsequent Third Harbor Tunnel North Approach project. Existing subsurface conditions and the Project's location at Boston's Logan International Airport significantly increases the difficulty of construction. The major contractual work involves relocating a reinforced concrete double box culvert supported on a continuous wood pile foundation. This existing culvert crosses and interferes with the future Third Harbor Tunnel North Approach alignment. Two parallel culverts constructed approximately 20 feet from either side of the future Third Harbor Tunnel alignment replace the existing double box culvert structure. Under the original contract design, approximately 3,100 feet of 14 ft. by 15 ft. reinforced concrete culvert is cast in place adjacent to the west side of the Third Harbor Tunnel and is located in the center of the Airport's main service roadway, Harborside Drive. This culvert is the Porter Street Combined Sewer, PSCS, which handles a combined flow of sewerage from the East Boston community and storm water runoff from Logan Airport. In addition, approximately 2,230 feet of 17 ft. by 15 ft. reinforced concrete culvert is cast in place adjacent to the east side of the Third Harbor Tunnel and is within 20 feet of an active aircraft taxiway and heliport. This culvert is the Bird Island Flats Storm Drain, BIFSD, which handles storm water runoff from the Logan Airport airfield. The existing outfall, on the west side of the Third Harbor Tunnel alignment is to remain in service and is to be connected to the new PSCS and BIFSD culverts. Therefore, a portion of the BIFSD culvert is designed as a bridge to span 128 ft. across the Third Harbor Tunnel excavation during construction.

Jan 1, 1994

By Li Keqiang

Among the pile foundations of the 156 tall buildings over 18 storeys in Shenzhen, 86. 5% of them are constructed by slurry drilled piles, bored piles and excavated piles (hand-dug caissons). Based on the experiences of the engineering practices, the paper points out that the main quality problems of pile foundations in Shenzhen are: insufficient bearing capacity of single pile; poor concrete quality of pile; damage of the precast pile; pile tip not reaching the required bearing stratum and the thickness of bored/drilled sediment exceeding the specified. etc. The quality inspection methods that have been used include: check of construction records and excavating; static loading test; core sampling test; non-destructive test, etc. Treatments of quality problems used in Shenzhen are also introduced in this paper.

Jan 1, 1991