Search Documents

By Angelo Siqueira da Silva

O processo de fricção e mistura, tem sido largamente estudado devido as microestruturas resultantes após o processamento, no qual são fortemente influenciadas pelos parâmetros utilizados durante o processamento. Este trabalho teve por objetivo avaliar a influência das variáveis de processo: rotações por minutos, velocidade de avanço, inclinação e penetração da ferramenta no material, na formação de macro defeitos em uma liga de alumínio 7475-T7351 em decorrência do processamento por fricção e mistura. A ação de caracterização e localização do defeito deu-se por meio de vídeo estereoscópio, onde foi possível observar a maior incidência do defeito de volume na zona de mistura (Cavidade), assim como uma preferência assimétrica quanto à localização do macro defeito no lado de retrocesso da ferramenta.

Oct 30, 2017

By Robert Pike

THE first authentic description of an iron bath for the deposition of iron is probably that of Bottger in 1846, who used a bath containing ferrous sulfate and ammonium chloride. In 1861, Kramer deposited iron from ferrous chloride solution. Electrolytic iron was produced in 1.869 by Bietz, who used it for making some magnetic tests. In the same year, Klein is said to have worked out his process. Jacobi1 in 1869 described the results obtained in electroplating with iron on copper for making dies and plates for bank notes, by Klein's process. A letter from Klein to Jacobi describes the bath more fully. It consisted of FeSO4 + (NH4)2S04. Lenz2 described ?some properties of electrolytically precipitated iron. He used Klein's bath, FeSO4 + MgSO4 + MgCO3, to neutralize and obtained fine-grained and hard iron. His conclusions were as follows: 1. Electrolytic iron and copper contain gases, notably hydrogen. 2. The volume of gas absorbed by iron varies within wide limits, but it is easy for iron to take up very considerable quantities of gas. 3. The absorption of gas is principally in the first formed layers of iron. 4. When iron is heated, gas begins to come off below 100°, principally hydrogen. 5. Heated to redness, reduced iron oxidizes in water, in part at least at the expense of the oxygen of the water, decomposing it and setting free hydrogen, which is partly or wholly absorbed. Siemens,3 in 1889, was the first to propose a general process embodying a step for leaching a sulfide mineral with ferric chloride or sulfate and a step for regenerating the leach and depositing iron on a cathode in a diaphragm cell. So far as is known, Siemens did not carry out his patent

Jan 1, 1930

By E. Hornbogen

Discontinuous precipitation in a iron can occur by at least two different mechanisms. These mechanisms are compared, using observations made on an Fe-22 at. pct Zn alloy and an Fe-19.5 at. pct Mo alloy. In the Fe-Zn alloy, precipitation began on grain boundaries. These boundaries moved into the supersaturated solid solution, providing nucleation sites and an easy path for diffusion. The precipitated phase pew as lamellae, perpendicular to the PRECIPITATION reactions are called discontinuous if the nucleation of particles does not occur on individual sites in the supersaturated matrix.' In discontinuous precipitation, nucleation and growth occur on a reaction front that moves into the supersaturated solution and leaves a two-phase aggregate behind. The term cellular precipitation2 has also been used, but the term autocatalytic precipi- moving reaction front. The orientation of the depleted iron differed from that of the supersaturated iron. In the Fe-Mo alloy the growing precipitate particles apparently created dislocations in the growth front which served as nucleation sites. The precipitate grew on (110) planes of the iron, and growth occurred through volume diffision. The depleted iron retained the orientation of the supersaturated solid solution. tation seems to describe the nature of such reactions best. The basic effect of such a precipitation mechanism in a solid is that it is able to move or create sites that can catalyze nucleation. Such sites can be grain boundaries and dislocations. A mechanism of autocatalytic precipitation must, therefore, include some rational process by which a grain boundary may move into the supersaturated matrix or by which dislocations may be generated in front of the reaction. Discontinuous precipitation is always in competition with individual nucleation and growth of par-

Jan 1, 1963

By Dr. -Ing. Rainer Alles

Introduction Belt conveyors usually run in a straight line. The correct alignment is a major criterion for reliable functioning and optimum running properties. Any misalignment of the conveyor, especially mistracking of the belt, can have many negative effects. As a consequence of this, damage can occur on the belt and conveyor, some material can he thrown off at the edges and serious running problems can arise. In the worst case the belt can come off its supporting structure so that operations are brought to a halt. The absolutely straight alignment of a belt conveyor is actually impossible so that on closer observation every belt conveyor contains more or less sharp curves. Whereas on non-movable conveyors the deviations from the straight can he kept within the range of practical measuring accuracy by careful installation, movable conveyors in surface mining or belt systems in difficult terrain often contain curves that are easy to see with the naked eye. Below ground, too, alignment cannot always achieved to a desirable extent or is changed by geological faults over the years. Despite these unwanted curves, most belt conveyors perform their function reliably. In view of the belt tension, the belt tends to take the easiest path. This in general is the shortest distance between the pulleys on which the belt is tensioned and bent. This means for example that for a curve radius of 10,000 m over a flight of 100 m the greatest deviation from the ideal line is as much as 12 cm. And a figure of this magnitude cannot normally he accepted. In such cases, use is made of guide devices to properly train the belt if it doesn't center itself anyway. If it's possible to control the belt position over such unwanted curves. it can also he expected that the belt tends to follow the desired curved path within certain limits. I'd now like to cite a few examples to illustrate the ways and means of guiding a belt conveyor in curves. Cost-effectiveness The advantages of belt conveyors, in particular for longer conveying distances and mass flows have been known and undisputed for some time. However, there are often obstacles standing in the way of the concept of straight routing. If a belt conveyor is to bypass elevations or existing buildings or to follow the seam of underground deposits or a predetermined path, then substantially tighter radii and longer curves are desirable or necessary.

Jan 1, 1993

By F. M. Waring

produced when zinc is substituted for a certain amount of tin are decidedly unsatisfactory. The substitution of aluminum for tin is entirely impractical, and such castings are worthless. This does not, however, exhaust all the possibilities of substituting other metals for tin in the copper-tin-lead alloys, but it is my opinion that the substitution of any other metals, in those alloys, can be made only by sacrificing the quality of the alloy. The possibility of substituting alloys of an entirely different type presents an attractive field for research. The copper-tin-lead alloy has attained its position as the most desirable bronze bearing alloy, but this does not mean that some other alloy may not be found which may give equally good or better results. In the search for such a substitute alloy it should be borne in mind that a bearing metal should possess the following properties: (1) It should be sufficiently rigid to support the load or resist the impact, but yet not so brittle that it will easily crack. (2) It should have as great a yielding or plastic nature as is consistent with its ability to support the load or resist the impact without deformation of the bearing as a whole. (3) The ideal structure combines a hard matrix to support the load and a softer metal or alloy contained within such matrix, to permit the bearing surface to adjust itself to irregularities of service. (4) It should be easy to handle in the foundry and machine shop. (5) It should be capable of being remelted without deterioration. (6) For use in babbitt-lined bearings, it should be capable of being tinned, so that the babbitt can be applied thereto. (7) It should have good heat conductivity in order to dissipate the heat generated by friction. Pennsylvania Railroad Anti-friction and Bell Metals F. M. Waring," Altoona, Pa.—Thc necessity for conserving tin has recently been very forcibly brought to the attention of all consumers, and efforts are now being made to reduce the tin content in certain alloys or to substitute other alloys not containing tin. The approximate composition of the non-ferrous alloys in general use on the Pennsylvania Railroad are given in the accompanying table. Phosphor bronze is used principally for rod bushings, main-rod brasses, and crosshead shoes. Ex. B bronze is used to a small extent for backs of car and coach bearings, but the majority of these are now made of the car-journal bronze, which contains, on the average, about 5 per cent. tin.

Jan 1, 1919

By W. L. Phillips

Stress-strain data are reported for sodium chloride, lithium fluoride, and magnesium oxide tested in compression at diffevent strain rates in the telrlperature range from 70° to 873°K. Quantitative equations are given for the stvain-rate dependence of the critical resolved shear stress and the initial rate of work havdening. The properties so determined are compared with results previously reported for metals. ALTHOUGH the effects of strain rate and temperature on the stress-strain characteristics of metals have been extensively investigated1,2 these effects have not been studied in detail in ionic crystals. In the only previous investigations on the effect of strain rate on the deformation of ionic crystals. Gilman and gohnston3 and Hulse and pask4 have shown that the yield stress of lithium fluoride and magnesium oxide at room temperature is proportional to the ninth or tenth root of the strain rate. CRYSTAL PREPARATION Lithium fluoride, sodium chloride. and magnesium oxide single crystals were purchased from the Har-shaw Chemical Co. The compression fixture and sample preparation have been described in detail previously.5 The detectable impurities in MgO were eight parts in 105 of Fe and six parts in 105 of Si; in LiF, six parts in 105 of Mg; and in NaC1, two parts in 105 of Fe and four parts in 10&apos; of Mg. The cleaved samples measured - 0.1 in. by 0.1 in. by 0.3 in. Prior to testing all samples were annealed at -0.8 of their melting point and cooled to room tempera- ture at 50 C per hr.&apos; Samples were strained at rates (<) of 0.1, 0.01, 0.002, and 0.0002 in. per in. per min. EXPERIMENTAL RESULTS Fig. 1 is a plot of the critical resolved shear stress a,. (extrapolation of slope of easy glide region to zero strain) of sodium chloride, lithium fluoride, and magnesium oxide tested at different strain rates as a function of temperature. In all crystals at all strain rates a, decreases with increasing temperature according to an equation of the type397 where uo is a stress constant, K is a constant, and T is the absolute temperature. The points in Fig. 1 are the average of six tests. It is evident that there is a break in the log 0,- temperature plots at a characteristic temperature T,. The constant K of Eq. [I] is dependent on strain rate, Fig. 2. The relationship

Jan 1, 1962

By D. M. Dabbs

A static dew point technique has been used to evaluate the solubility of arsenic in ?slag and its dependency on P02 at temperatures of 1458 and 1523K. The ferrous-ferric ion ratio of the slags ranged from 3.9 to 23.8. These values correspond to partial pressures of 02 ranging from 10-8 to 10-12 atm. The solubility of arsenic in slag was found to be independent of? P02? The data indicate that elemental arsenic exists in silicate ?slags. This result was further substantiated by mass .spectrometric analysis of doped slag specimens.

Jan 1, 1983

By Gyan S. Rajhans

"The strategy of fibrous dust sampling is discussed, various sampiing methods are critically reviewed .and their application to coal dust is demonstrated. Fibre counting is described in detail. An attempt is made to explain the basis of determining the threshold limit value of asbestos and other dusts. The paper also discusses such dust control methods as enclosure of the process, effective local exhaust ventilation, segregation, substitution, wet processing and continuous monitoring of the return air for recirculation."

Jan 1, 1970

By Richard L. Fischer

Constant-volume charges of precipitated PETN (pentaeythrite tetranitrate) at three specific gravities (0.50, 1.00, and 1.50) were used in laboratory tests to examine the effects of changes in explosive properties on free-surface displacement pulses and on crater dimensions. The tests were performed in large blocks of cement-mortar. The values for the detonation velocity, detonation pressure, specific energy, energy density, and energy release rate were calculated from the explosive loading density. Calculated explosive properties were correlated with free-surface displacement pulse measurements, strain energy, and measured crater dimensions. Increases in explosive properties resulted in increased free-surface displacement pulse parameters and crater dimensions. The loading density, detonation velocity, energy density, detonation pressure, and energy release rate were found to be best indicators of explosive performance. Simple acoustic relationships involving impedance ratios were examined and could not be used to predict peak displacement amplitude or strain energy. Data are presented in the customary English units as well as the International System of Units (SI).

Jan 1, 1970

By D J. Williams, A K. Kho, A Shokouhi, N Tucker

The disposal of dewatered coalmine tailings and coarse reject within spoil piles is gaining popularity as a means of eliminating separate surface tailings storage facilities or dams. The contrasting characteristics of coalmine spoil, coarse reject and tailings are somewhat complimentary, making the co-disposal of dewatered tailings within spoil piles geotechnically feasible and environmentally attractive. However, the impacts of mixing plant rejects within spoil piles are not well understood; in particular, the effects of water draining from the mixed plant rejects on the moisture content of the surrounding spoil. Changes in moisture content can cause additional collapse and degradation settlements of the spoil pile. A series of laboratory tests has been undertaken on mixtures of dewatered coalmine tailings, coarse reject and spoil. The results of these tests have been incorporated into a spreadsheet-based settlement prediction tool to investigate the effects of incorporating mixed plant rejects on total spoil pile settlements. This paper presents the laboratory tests undertaken, the incorporation of the test data into the settlement prediction tool, and settlement estimates for the various mixtures at different stages of construction.CITATION:Kho, A K, Tucker, N, Williams, D J and Shokouhi, A, 2015. Impact of co-disposing mixed plant rejects on spoil pile settlements, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Shadia J. Ikhmayies

"Cadmium telluride (CdTe) is a very interesting material that has many applications. Thin films of p-type CdTe can be used as the absorber layer in the heterojunction CdS/CdTe thin film solar cells in which n-type cadmium sulfide (CdS) works as the window layer. A review of the photoluminescence (PL) spectra ofp-type CdTe thin films prepared by different techniques was performed. The presence of defects and impurities such as oxygen and chlorine influence the PL spectrum. Copper and other dopants change the PL spectra and enhance the defects band. Chemical-heat treatment especially with CdCh is known to improve the quality of CdTe thin films because it decreases the Cd vacancies and quenches deep traps, so it enhances the PL signal. A discussion of chemical-heat treatment especially with CdCh, the effect of the ambient atmosphere, and that of the measuring temperature is performed.IntroductionCadmium telluride (CdTe) is a II-VI compound semiconductor that has a cubic zincblende (sphalerite) structure with a lattice constant of 0 A4~11]. Other than all of II -VI semiconductors, CdTe can be made both n- and p-type. But due to self compensation it is not easy to get p-type CdTe films [2]. Polycrystalline CdTe thin films are interesting because they have a lot of applications. Most of the problems associated with the use of these films are attributed to inhomogeneity, self-compensation, and the difficulty of forming a stable and lowresistivity ohmic contact [3]. CdTe technology has been established for a large number of applications, including solar cells, optical and nuclear detectors, and thermal- and radiationimaging devices [3]. At present, the highest demonstrated conversion efficiency for a CdTe based heterojunction (ID), with CdS as a window layer, is 16.5% [4, 5]. CdTe thin films can be prepared by different experimental techniques, such as thermal evaporation [l], electrochemical deposition (ED) [3], close-spaced sublimation (CSS) [3, 4, 6], physical vapor deposition (PVD) [3], chemical molecular beam deposition (CMBD) [7], and close space vapor transport (CSVT) [8].The objective of this paper is to make a review of the photoluminescence (PL) spectra ofp-type CdTe thin films prepared by different techniques and discuss the factors that influence the PL spectra. The composition of the film is very interesting in determining its PL spectrum. Different kinds of defects, impurities and dopants have their finger prints in the PL spectrum. Deposition techniques and deposition parameters such as the deposition temperature and ambient atmosphere also have their influence. Heat and chemical treatments which are known to improve crystallization and reduce the defects change the PL spectrum."

Jan 1, 2013

By Karollyne Gomes de Castro Monsores

Os materiais poliméricos são sensíveis a radiação ultravioleta, acarretando mudanças em suas propriedades. Sob esta perspectiva, o presente estudo expôs o polietileno de baixa densidade (PEBD) a radiação ultravioleta por 150 e 300 horas. A avaliação físico-química e a caracterização mecânica foram realizadas para verificar as mudanças macromoleculares produzidas por tal radiação e confirmadas por exame visual. Diante dos resultados, confirmou-se a ocorrência de degradação, através da presença de ruptura de cadeias, além da produção de reticulação, e um sutil decréscimo da cristalinidade. O ensaio de tração confirmou a fragilização produzida pela radiação. O desempenho balístico das placas fixadas por adesivo a base de etilcianoacrilato produziram delaminação, ao contrário do observado nas placas fixadas por silicone.

Oct 30, 2017

By Filipe Augusto Vasconcelos Guimarães

O presente artigo discute as interferências causadas pelo incremento gradual de umidade nos minérios produzidos atualmente, especialmente aqueles produzidos diretamente para carregamento. O aumento de umidade representa um desafio constante no transporte e tratamento dos materiais produzidos, uma vez que a simplificação dos fluxogramas pode também significar uma importante parcela na redução dos custos, tema hoje primordial na sobrevivência de qualquer empreendimento de minério de ferro. A utilização de reagentes auxiliares para ajudar no tratamento e transporte desses materiais pode significar a diferença entre a manutenção ou o fechamento de uma mina.

Aug 16, 2017

By B. A. Ashley

Rosebud Mining Co. (RMC) is based in Kittanning, PA. As of October 2013, it operated 24 active underground mines in Pennsylvania and Ohio. RMC?s Tracy Lynne Mine is located approximately 5 km (3 miles) east of Apollo, PA, (approximately 48 km or 30 miles northeast of Pittsburgh, PA) and mines the Lower Kittanning coal seam. The coal seam averages approximately 1.1 m (45 in.) thick and is of steam coal market quality. The mine is a single unit operation. Coal is mined using a continuous mining machine and is transported from the face to the conveyor belt using a continuous haulage system. Typical ventilation in the mine consists of an exhausting fan that draws air through isolated intake, belt and return air courses (Fig. 1).

By R. C. Emmett

Gravity sedimentation is one of the most widely used unit operations in mineral processing and hydrometallurgy. Properly selected and operated sedimentation equipment can provide probably the most economical means of concentrating solids or clarifying solutions. Because of the variety of different approaches possible, including the use of modern flocculants, it is easy to overlook the optimum approach in selecting equipment. The different types of sedimentation systems that can be used in the minerals field and the sizing methods that are currently employed will be discussed here. Sedimentation applications usually fall into two areas, clarification or thickening. While the two operations are basically similar, the difference in emphasis (a well-clarified overflow as opposed to a highly concentrated underflow) results in significant differences in testing, equipment design, and operation. Clarifiers may be merely simple settling vessels with no special features, other than ample volume to provide the detention time needed for suspended solids to settle out of the feed slurry. Or, they can be designed to employ elaborate solids-contact techniques utilizing coagulants or flocculants to achieve more rapid clarification through the growth of particle agglomerates. Thickeners also are available in a wide variety of designs, with the main differences concentrated in the design of the raking mechanism. Thickeners operating in series (continuous countercurrent decantation or CCD) are used to recover valuable solution or purify the insoluble solids. Tray thickeners are used for recovering fine particulate solids such as alumina seed, but in other applications have been supplanted largely by unit thickeners or inclined plate units. Thickeners and clarifiers sometimes are used for storage of either solids or overflow liquor, or employed as precipitating reactors, such as in desilication applications. The use of flocculants and coagulants is much more common in modern processing plants, primarily due to the reduction in capital costs rendered possible through the use of these reagents. The terms flocculant and coagulant are often used interchangeably; generally, it is understood that flocculants refer to organic, high molecular weight synthetic or natural polymers which are useful in flocculating most suspended solids, but generally are ineffective on colloidal suspensions. Coagulants refer to chemicals such as those commonly used in water treatment, alum, ferric salts, lime, etc., which are usually far more effective on colloidal solids but cannot achieve the degree of agglomeration that is possible with the polymers. In some cases, both coagulants and flocculants are used in order to achieve optimum results.

Jan 1, 1986

By H. N. Eavenson

The eleven mines of the United States Coal and Coke Co. in the Pocahontas coal field are situated in McDowell County, W. Va., which is a mountainous region. The valleys rarely exceed 200 ft. (60 m.) in width, the hillsides slope from 25°to 33°, and the tops, from 600 to 900 ft. above the valleys, carry practically no level land. At least 80 per cent. of the area is covered with timber. All the workings are drift mines; and while the average grades of the seams worked are ample for drainage, local dips and swamps necessitate the use of a large number of local pumps or of numerous drainage ditches to keep the mines free from water during heavy rains. The water handled in any mine is not great, compared with the coal output, and usually causes little trouble except during extremely wet periods. In new workings, the water encountered, except in rare cases, is trifling; it is only after rib drawing has started and the surface has been broken that water troubles begin. The strata overlying the coal are sandstone, shales, and slates; as the soil is thin and sandy, it does not tend to puddle and stop the cracks, which remain open for a long time. As mining progresses and the robbed area increases, the broken area becomes larger, increasing the openings into the mined territory. The cover over the robbed portions of the mines varies from 30 to 750 ft. (9 to 228 m.). When the ground is saturated, considerable water finds its way into the mines the day after a heavy rainfall and for three or four days it tends to fill the low places, wash the tracks, etc. and unless from three to four times as many pumps are installed as are normally needed, considerable output is lost. In most cases the water will flow from the mines, and the obvious solution is to provide drainage ditches of ample size to carry the maximum flow expected, so that the inflow will have no opportunity to flood the working places. Laying out the drainage headings on the proper average grades was an easy matter but where blasting was necessary to provide uniform grades, as was frequently the case, it was important that the maximum flow to be expected and the size of ditches to be provided should be known so that only rock work necessary to provide proper drainage

Jan 1, 1922

By Tukkimies M

During the late-1980s crawler-mounted crusher units established their position in the aggregates industry. Between 1986 and 1994 about 700 units were delivered to customers all over the world for surface operations, mainly in Scandinavia and central Europe. The crawler-mounted units are popular among smaller crushing operators because they are versatile and easy to move between sites. In large quarries the greatest benefit is obtained by combining a primary crawler-mounted crusher unit with mobile belt conveyors which eliminates the need for costly haulage by dump truck. Savings of up to 40 per cent in production costs prior to secondary crushing have been achieved. Today the environmental aspect in quarrying is assuming ever greater importance. Besides being costly the dump trucks are also the major source of dust and exhaust fumes within a quarry. A complete face crushing system consisting of a crawler-mounted crusher unit and mobile belt conveyors can be electrically driven and can be equipped with dust encapsulation and dust collectors. A mobile crushing unit is not a new idea. From the mid-1950s onwards the mobile and self-propelled units have been built equipped with crawlers, tyres or walking mechanisms, with weights usually of 500-1000 t. Due to their massive size these unit are not mobile in the same way as the today&apos;s mobile units. It is not feasible to move them more than a few times a year unlike today&apos;s fully mobile units which are often relocated once an hour. This means that the massive units can not continuously follow the production face and their loading always requires a certain amount of haulage. Today the mining industry is facing new challenges. With low mineral prices and high labour costs, increasing productivity is essential for survival. New standards are also being set for the labour safety and the environment. Large research programs have been launched to meet these challenges. However, technology which can partly solve these problems already exist and is only waiting to be introduced into underground applications as well - the mobile crushing unit followed by belt conveying. As in surface operations the elimination of truck haulage also brings considerable savings in operating costs in underground mines and reduces the amount of dust and exhaust gases generated. An additional benefit especially in underground applications is improved safety. In an underground mine most accidents are caused by moving vehicles.

Jan 1, 1995

By M. H. Richman, L. M. Markowitz

MUCH of the available information on which the heat treatments of a particular steel are based is found in the isothermal-transformation diagram. Such is the case despite the fact that the usual thermal treatments involve continuous transformations, i.e., transformations which occur on cooling, rather than isothermal transformations. This rather unusual practice is continued because of the abundance of published isothermal-transformation diagrams1, 2 which are relatively easy to determine experimentally as compared to continuous-transformation diagrams.3, 4 However, this can easily lead to the production of improper micro-structures and may not allow full advantage to be taken of the inherent hardenability of a steel. A mathematical method of estimating the continuous-transformation diagram from the available isothermal data was developed by Grange and Kiefer;5 but, due to the mathematical approximations required in the calculations, the computation of continuous-transformation diagrams has been limited to individual cases and no large-scale compilation of these diagrams is available. With the present availability of high-speed digital computers, the problem of time-consuming approximations may be minimized and continuous-transformation diagrams may be constructed with the insertion of isothermal data into a basic program. It is the purpose of this report to announce the availability of such a program and compare the computed and experimental continuous-transformation diagrams for two different steels. Let us first review the method of Grange and Kiefer5 and then compare the results of the machine calculations with the experimentally determined diagrams. In order to apply this method, one requires the isothermal-transformation diagram and a set of curves representing cooling at constant rates. A section of an isothermal-transformation diagram is shown in Fig. 1 together with a cooling curve of M0F per sec. The cooling curve is constructed to start from the A1 (eutectoid) temperature if the transformation product is the eutectoid microconstituent (i.e., pearlite or bainite), from the A3 temperature if the product is primary ferrite, or from the 4, if it is proeutec-toid cementite. The cooling curve in Fig. 1 intersects the curve representing the start of isothermal transformation at a point A&apos; corresponding to a temperature TX and a time fX. An arbitrary lower temperature To (on the

Jan 1, 1968

By William O. Macha G

El presente trabajo describe la molienda y flotación como etapas de mejoramiento en la metalurgia del plomo en Paragasha. Para ello, se revisa los principales problemas de la metalurgia, como el de los minerales encontrados en la superficie, entre otros. Asimismo se describen los circuitos pertinentes de la planta piloto, como de la planta Paragasha y los resultados metalúrgicos en los meses de enero a marzo en 1965. En el primero, se señalan las dos etapas de molienda y flotación en el Pb, mientras que en el segundo, se muestra el circuito stándard: molienda y flotación.

Aug 20, 1965

By T. A. Lang

The objective was to develop a Program Plan of analytical studies and tests for determining (1) the optimum installation tension of a coal mine roof bolt, (2) the most valid bolt support theory or theories, and (3) the most valid roof failure theory or theories. On this basis a comprehensive literature search was made and significant material dealing with coal mine roof behavior, roof bolting and roof support was collected, reviewed, classified and analyzed. Emphasis was given to the influence of rock reinforcement on the control of deformation, stress field modification and mine roof stability. An assessment was made of the effect of various parameters including bolt tension, bolt pattern and time of installation, on the effectiveness of rock reinforcement systems, and equations developed for bolt tension as a function of these parameters, and rock properties. From these studies, a major program plan of tests and studies was developed for verifying and validating the most tenable theories of roof behavior and roof support and for determining optimum bolt installation tension.

Jan 1, 1979