Search Documents

By G. K. Manning, P. C. Rosenthal

USE of copper as an intentionally added alloy in steel and cast iron has rapidly expanded with-in the last fifteen years. It is estimated that in 1931 not more than 2000 tons of copper were so used; by 1941, however, this figure had grown to 13,000 tons. Tonnage figures during the war years have been restricted just as copper itself has been restricted, but copper-bearing cast irons and steels have played a part in the production of ordnance equipment. They are used in gun carriages, airplane landing-gear assemblies, scout cars, bulldozing equipment, army trucks, armor plate and many other instruments of war. These wartime applications have their counterpart in many peacetime applications; derricks, dredges, mine equipment, railway equipment, trucks, farm implements, automobiles, and tractors, all usually contain some parts made of copper-bearing steel or iron. An example of this is the Ford tractor which in 1940 contained over 300 lb. of copper-bearing steel castings. To this list should be added corrugated building sheet for exterior use most of which, at the present time, contains upward of 0.15 per cent copper. With the return to peacetime economy and the removal of wartime restrictions, it appears certain that copper cast irons and steels will find increasing application in civilian goods.

Jan 1, 1945

By Morgan M. Sears, Mark Morris, Joseph Bright

In an effort to advance the science underlying modern coal pillar stability analysis, researchers at the National Institute for Occupational Safety and Health are currently involved in research aimed at better understanding the impact of an in-seam rock parting on the strength of coal pillars. The purpose of this study is to determine a suitable virtual mining height that could be applied using current pillar stability analysis tools. To accomplish this, the boundary element model LaModel was used to back analyze data collected on pillar performance in a room-and-pillar panel at the Maple Eagle Mine located in Southern West Virginia. In a previous work, data collected from borehole pressure cells (BPCs) and extensometers were taken from three instrumentation sites. Data collected from the back bleeders were used to measure the rear abutment stresses, and data collected from two instrumentation sites in the wraparound bleeder were used to measure the front and side abutment stresses as well as the peak strength and performance of the slabbed leave pillar. The utilization of two nearly identical instrumentation sites in the wrap-around bleeder provided much needed repeatability of the obtained measurements. In this study, the data collected from BPCs at the three instrumentation sites was calibrated to match the Bieniawski pillar stress gradient. To model the measured pillar behavior, the LaModel program was selected due to its capability of being directly comparable to the Analysis of Retreat Mining Pillar Stability (ARMPS) and Analysis of Coal Pillar Stability (ACPS) programs. The model was then calibrated to match the measured abutment extent and abutment stress. Finally, the model was validated by reducing the modeled mining height until the yielding of the slabbed leave pillars in the model matched what was measured in the field. The final calibrated mining heights show that a reduction of the shale parting thickness, not including any clay layers, of 52% is applicable. This research study provides the first known measurement of the ARMPS/ACPS “50% Rule” and its applicability to this panel of the Maple Eagle Mine. This finding provides a proof of concept and could have significant implications for future research.

Feb 1, 2024

By S R. Pecover

AustraliaÆs opal and sapphire mining industry has fallen from its peak in the 1980s and 1990s into a significant low today. This is not due to exhaustion of the resource, but instead an over-reliance of the Australian miner on achieving a fair price for the gemstone product from offshore middlemen dealers. Gemstone and geological research is also at a low as Federal higher education expenditure has fallen with research institutions relying increasingly on private funding in an environment of restricted autonomy and flexibility for researchers. What little remaining research skills the universities have is being bled into the private sector as a result of the mining boom and encouraged by lower than average academic salaries. Nevertheless, some highly innovative research has been taking place, often by self-funded individuals and retired academics simply with a desire to advance the understanding of the particular branch of science in which they are interested. New models for the formation of sapphire and opal are now beginning to be applied to the exploration for these gemstone commodities. This research, together with well thought out plans for managing the gemstone product through its value-adding steps to the jewellery retail level, has the potential to bring about a resurgence in the Australian gemstone industry.

Jan 1, 2008

By Michael David Harmse, Wiehan Adriaan Pelser, Jean Herman van Laar, Cornelius Stephanus Lodewyk Schutte

The South African deep-level mining industry is characterised by high operating costs and narrowing profit margins. Compressed air is commonly the largest consumer of energy in these mines, and any inefficiencies reduce profitability. Various methods aiming to optimise the compressed air networks have been implemented without an ideal economic dispatch strategy due to the lack of compressed air storage. In this study, a genetic algorithm was developed to evaluate the financial benefit of converting underground haulage to act as an air receiver (compressed air storage). By converting inactive haulage of 1.17 km in length into a volumetric air receiver, an annual monetary benefit of R2.5 million ($163 200) can be achieved, with a payback period of fewer than eight months. However, implementing the ideal size air receiver would result in an annual monetary benefit of R7.67 million ($500 700).

Jul 11, 2022

By Sandeep Kumar Asarapalli, Sunil Kumar Bisoyi, Bhatu Kumar Pal

Spontaneous heating of coal is one of the major concerns in the coal mining industry. Hundreds of millions of tons of coal are lost each year because of spontaneous heating. If necessary arrangements are made, many fires due to spontaneous heating may be avoided. Therefore, protective measures have become essential to prevent coal from spontaneous combustion. A large amount of coal reserve can be saved by the assessment, suppression, and prediction of spontaneous heating of coal, which also helps in betterment and efficient coal production. The use of chemical retardants can act as inhibitors for the liability of coal toward spontaneous heating by increasing its ignition temperature, thereby, increasing its incubation period. The coal-chemical mixture can be used for whitewashing the exposed coal in galleries as it creates a layer between coal and oxygen in the atmosphere, delaying the oxidation process and ultimately inhibiting the spontaneous heating liability of coal. This work examines the effect of chemicals such as sodium chloride, calcium carbonate, potassium iodide, sodium nitrate, and potassium chloride on the spontaneous heating of a coal sample. Thereby, it suggests a better chemical for inhibiting the liability of coal toward spontaneous heating. The experimentation involves flammability temperature (FT), crossing point temperature (CPT), and differential thermal analysis (DTA). The ignition and oxidation temperatures were found from the above experimental methods for Lingaraj open-cast coal mine samples, with and without adding chemicals. The results are cross-checked and verified through DTA. Correlation analysis was carried out among the results obtained from CPT, DTA, and FT, and better chemical retardants that effectively inhibit coal’s tendency toward spontaneous heating were suggested.

Dec 23, 2023

By Thien Sok, Yaojun Lu, Craig Gilbert, Jeremy Scott

Feedwells play a pivotal role in gravity thickeners, governing flow distribution, feed dilution, and flocculation condition during solid–liquid separation. This study presents an optimized design and digital prototyping framework for FLSmidth’s E-volute and E-Duc Feedwell systems, integrating advanced computational fluid dynamics (CFD) with quantitative criteria introduced at SME2024. Building on established FLS technologies, a series of novel configurations were developed and systematically assessed under full-scale and site-specific conditions. CFD provided quantitative insight into flow distribution, feed dilution, and flocculation efficiency, enabling iterative refinement of design parameters. The optimized feedwell demonstrated superior hydraulic performance, enhanced mixing, and improved flocculation outcomes. Beyond the specific design advances, the work highlights CFD as an effective and economical tool for digital prototyping, facilitating early identification of design limitations, reducing dependence on physical trials, and accelerating innovation. The methodology underscores the value of simulation-driven design in advancing feedwell performance and improving thickener technology.

Feb 22, 2026

By H. Mullani

We have in southeast Kansas a variety of soils underneath which are a variety of subsoils compressed into what is commonly called “ hard pan.” These soils are of six types, ranging from a clay to a sandy loam. The surface soil in Cherokee County and Crawford County, of whatever quality or type is, generally speaking, from 6 to 12 inches in depth. The so-called “hard pan” ranges from the native grass roots to a depth of from 2 to 12 feet, and in some places even deeper than that.

Jan 1, 2010

By Tina Maniatis

Applied Biosciences has developed a biological technology for removal of arsenic, nitrate, selenium, and other metals from mining and industrial waste waters.The ABMet® technology was implemented at a closed gold mine site in Canada for removing arsenic from tailings pond water. The system included six bioreactors that began treating water in the spring of 2004. Design criteria incorporated a maximum flow of 567 L/min (150 gallons per minute) and water temperatures ranging from 10°C to 15°C. Influent arsenic concentrations range from 0.5 mg/L to 1.5 mg/L. The ABMet® technology consistently removes arsenic to below detection limits (0.02 mg/L). Data from the full scale system will be presented, as well as regulatory requirements and site specific challenges. Keywords: Arsenic, Sulfate Reduction, Metal Sulfide Precipitate, Biological Water Treatment

Jan 1, 2005

By Wankun Wang, Fuchun Wang

Based on the study of artificial neural network, the neural model was established for the prediction of germanium extraction from zinc oxide dust by microwave alkaline roasting-water leaching. Alkali-material mass ratio, microwave heating temperature, liquid-solid ratio, aging time, leaching time and leaching temperature were the significant factors for the process. The results indicated that the neural network prediction model was reliable, and the forecast values fitted well with the actual experimental values. The model could be used to predict the regeneration experiments with high credibility and practical significance. The accuracy of convergence of the model reached 10−5.

Mar 1, 2018

By Seth T. Reese

THE INJURY DATA and experience at coke ovens in the United States for 1952 are presented in this bulletin under the following general sections: (A) General injury experience: Tables 1 to 9: Contain current and comparable data on operating statistics, number and classification of injuries, frequency rates, and accident agencies involved in causing injuries. Data are given for the industry as a whole, for each type of oven, and for the States in which coke is manufactured. (B) Selected injury experience: Tables 10 to 15: Contain comparable injury data in the coking industry covering 5- and 10-year periods on the number of injuries, accident agencies, and severity of injuries. (C) Historic injury experience: Tables 16 to 19: Contain data on the number of injuries, frequency rates, and employment at coke ovens from the earliest records through 1952, Operating statistics from 1929 through 1952 are given in table 19.

Jan 1, 1955

Coal mining legislation makes frequent reference to æSafety Management SystemsÆ but there is a chronic shortage of useful guidance material as to how these might be applied to hazardous exposures. Several studies have indicated that for each death that is reported as a result of an industrial æaccidentÆ, there are five deaths that caused by occupational exposures. Because the deaths from occupational exposures do not occur on site and often well after employment has ceased, they are generally unreported. Improved access to mortality data from coroners, the Australian Institute of Health and Welfare and superannuation service providers (early claims from death and total permanent disability), has given rise to some analysis of death and disability data that provides evidence that there are emerging opportunities to develop and improve safety management systems for hazardous occupational exposures. Issues explored include how safety management systems might be developed in relation to dusts and chemicals and other hazardous exposures to ensure the risk of disorders with long latency periods are reliably assessed and the exposures effectively managed. The current standards and guidelines which refer to safety management systems in general or to management of exposure related hazards are examined. Many standards are based on dose-response studies that provide for an acceptable percentage of workers to suffer adverse health outcomes. An alternative management system might be to apply dose-response relations to health surveillance to identify æat riskÆ individuals and effectively manage health and related safety risk at an early stage.

Jan 1, 2005

By John Hillman

The reconstruction of the British mining industry which began shortly after nationalisation in 1947 continued until well into the 1950s with the support of the Government. This support diminished as plentiful supplies of cheap oil from the middle East made many coalmines un¬economic. The planned rundown which followed was foreshadowed in the 1965 White Paper which outlined the financial measures to speed the closure of uneconomic collieries. The decline appeared likely to continue into the 21st century as the role of coal in UK energy requirements became less and less significant. This policy was well on course in 1973 when the oil crisis led to a complete reappraisal of the position. A Government examination in 1974 of the coal industry then supported the National Coal Board's general strategy of major capital investment as set out in its 'Plan for Coal' (1). Plan for Coal aimed at halting the intended decline in the industry's capacity and restoring it to 120 million tons of deep mined output in 1985. The Plan proposed action along the following lines (a) increase output by major Investment in construction at existing collieries with sufficient reserves to give 13 million tons per annum extra output (b) invest in extending the life of existing collieries by gaining access to additional reserves, to give 12 million tons per annum extra output © by sinking new mines, produce an extra 20 million tons per annum. Figure 1 shows the contribution (2) expected from each of the three sources up to 1990/1. The measures taken were expected to offset the inevitable exhaustion of existing pits and provide the additional 40-42 million tons capacity needed to restore annual output in 1985 to 120 million tons. Parallel to this programme for expansion of deep mined output, opencast mining was to produce 10-15 million tons per annum. A recent review however, indicates that new mines are likely to yield only 10 million tons per annum by 1985, mainly owing to the need for public inquiries into proposals for new mining and the resultant fact that planning approval takes 'much longer than originally expected. Nevertheless the objective of 120 million tons deep mined output by 1985 is still considered achievable of means of a greater contribution from existing mines. This programme was originally estimated to cost 2,-56 million dollars at March 1974 prices, out revised estimates of the cost of Plan for Coal indicate that it may now exceed 6,960 million dollars at mid-1977 prices. Plan for Coal includes a substantial investment in new and reconstructed coal preparation plaints. At mid-1977 prices more than 322 million dollars Ls so be invested in coal preparation projects in the UK, at the rate of, about 70 million dollars a year. This rate 3f capital expenditure has been maintained over the past three years and covers investment in a wide range of coal preparation coals for the power station, coking and domestic markets.

Jan 1, 1978

By J. Kretschmann, H. Mischo, O. Drusche, S. Krause

Mining is and will be inevitable in spite of the increasing implementation of circular strategies. The energy transition and population growth will boost the demand for critical raw materials. It is the opportunity for miners to reinvent their business models. Generating attractive new business cases with sustainability-oriented innovations meets investor and stakeholder expectations from the beginning. This contribution guides managers on their pathway towards sustainable success. Contextual sustainable business model patterns will be presented that can be adjusted individually, regardless of actor’s size. It will also point out, how sustainable value creation can be measured on business model level.

Feb 1, 2023

By K. F. Anderson

The increasing number of oil-productive reservoirs in the Ellenburger formation has emphasized the need for information pertaining to the hydrocarbon recoveries that may be obtained from such reservoirs. Most of the space available for accumulating hydrocarbons in the Ellenburger formation is derived from fractures, which makes it difficult to estimate reserves or probable recoveries. The Ellenburger reservoir in the Big Lake field was selected for study because it is one of the few near-depleted reservoirs in the area. The experience gained in operating and developing this reservoir has been and should continue to be a helpful guide to operators both in predicting recovery and establishing methods of development and operation In similar reservoirs. Development and production data were gathered from different sources. The writers have compiled and interpreted these data to estimate the ultimate recovery of hydrocarbons. In addition to the estimates of ultimate recovery, the report contains sample calculations and estimates of theoretical recovery based on different methods of operation. The calculations presented in this report indicate that the Ellenburger reservoir is 95 percent depleted and that the ultimate recovery of hydrocarbon liquid from the oil reservoir and gas cap combined will he 4-0 barrels per gross acre-foot of reservoir rock. An estimated 32 barrels of condensate per gross acre-foot of reservoir rock in the gas cap has been recovered, and the estimated ultimate recovery of crude oil will be 47 barrels per gross acre-.foot of rock in the crude-oil reservoir.

Jan 1, 1954

By X. Gumede

A model is being developed to quantify the benefits for mining houses resulting from the reduction in greenhouse gas and energy consumption by the application of innovative blast designs in addition to direct financial benefits throughout the mine to mill value chain. The conversion from shock tube initiation systems to electronics and some changes to powder factor measured on an open pit mine had previously been used to show significant improvement on blast outputs. Benefits were realised on drilling, blasting, loading, hauling and beneficiation. Quantification of the relationship between powder factor and reduced greenhouse gasses is investigated in this study. The study has highlighted new data that must be recorded and hence some assumptions were made as to fuel consumption and the energy in crushing was obtained from the Bond work equation. The mine to mill projects in an open pit platinum mine and a quarry produced energy savings and reduced greenhouse gas emissions associated with the careful application of explosives and blast innovations. The less fines project showed an increased carbon footprint. The model provides a new insight into how project feasibility should be decided based on economic and environmental viability.

Jan 1, 2012

By Andrew Logan

Newcrest has a strong history of growth over the past 20 years, yielding value from previously marginal ore bodies. We have grown regionally in Asia Pacific through our operations in Australia, Indonesia and Papua New Guinea, and also established a beachhead in West Africa. The company has a reputation of realizing value from large, low-grade deposits adopting step change approaches. Newcrest is focused on an overall strategy of gold, low cost, long life and moderate growth. Capability step changes play a large delivery role. They transition from a business offline-to-online approach as opportunities mature. Newcrest believes in a) Knowing what ?good? looks like, b) An open innovation approach to actively working with others, c) The leap frogging leverage of making the ?old new again?, d)An adopt-adapt-develop methodology enabled by rapid prototyping/piloting, e) Getting our handsdirty with test work and plant analysis, and f) Staying focused on a few high business leverage areas. This paper describes Newcrest?s approach and our experiences in establishing renewed metallurgical processes, specifically aimed at increasing innovation adoption. Some of our step changes discussed include: 1) Early waste rejection to avoid high energy processing downstream, 2) Broader gold product channels to reduce site based processing needs, 3) Lower energy processing, and 4) Geo-Metallurgy approaches. Keywords: Newcrest, gold, step change, open innovation, adopt, adapt, develop, offline, online, prototyping, old new again, waste rejection, low energy, geo-metallurgy

Sep 1, 2012

By S. Koski

The Cerro Verde copper-molybdenum porphyry mine, majority owned and operated by Freeport- McMoRan Copper & Gold, is located 30 km southwest of Arequipa Peru. The concentrator, which produces copper and molybdenum concentrates, started operating in late 2006 with a 108,000 tpd design capacity, processing primary sulfide ore (mainly chalcopyrite and molybdenite). Plant capacity was recently increased to 120,000 tpd. The comminution circuit consists of one 60? x 113" primary crusher, four MP-1000 secondary crushers in closed circuit with dry screens, four 2.4m x 1.6m High Pressure Grinding Rolls (HPGRs) in closed circuit with wet screens, and four 7.3m x 11m gearless ball mills in closed circuit with cyclones. The HPGR circuit is fed by the Secondary Crushing circuit product at a T80 of 35 millimeters, and the HPGR circuit product feeds the Ball Mill circuit at a T80 of 3000 microns. This paper describes operating experiences with HPGRs during these first four years highlighting improvements in operating practices and presentation of data regarding operational efficiencies, also discussed are the primary benefits provided by HPGRs such as production of micro fractured particles, reduced ore Bond Work Index, and reduced power consumption. Cerro Verde represents the first installation of HPGRs in both the copper industry and large scale hard rock mining.

Jan 1, 2012

By P. James

"INTRODUCTION Control of target stream pH is very important in leach mining and treatment of MIW (mining influenced water). On the production side, solution acidity can impact SX (solvent extraction) effectiveness through PLS (pregnant leach solution) and raffinate pH. Many older operations and legacy mining sites generate ARD (acid rock drainage) that is too weak for profitable metal production by conventional means and faces costly wastewater treatment for mitigation and disposal. For wastewater and environmental treatment, neutralization to precipitate and remove metal contaminants to clean the wastewater is the dominant approach. Traditional lime neutralization and precipitation is most often used but results in large amounts of mixed metal sludge requiring costly disposal. Blue Planet Strategies (BPS); which focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources, has developed a new “reagentless” neutralization process. Electricity is utilized in its proprietary DEMET™ (Dynamic Electrolytic Metal Effluent Treatment) platform capability to controllably raise target stream pH. The method offers a simple, low-cost approach yielding cleaner treatment chemistry. It can result in less sludge generation and enables possibilities to selectively recover contaminants as potentially saleable products for new revenue generation to offset further offset treatment costs. DEMET Overview BPS’s patented electrolytic DEMET platform leverages solid scientific and chemistry foundations through its advanced design to achieve capabilities and performance not previously realized. DEMET technology combines separated compartment electrolytic cell functionality with proprietary advanced dynamic electrodes and cell configurations to achieve a variety of chemistries and processing targets.[1-6] DEMET‘s unique elements can yield higher processing rates at practical efficiencies, lower energy consumption, plus improved processing stability and lower maintenance requirements due to enhanced resistance to cell fouling and shorting; while also thwarting cross stream (catholyte vs. anolyte) contamination. Consequently, DEMET can provide a superior, extremely versatile, and more cost-effective electrolytic treatment option where a multitude of FEED and PRODUCT stream combinations might be employed in comparison to traditional tankhouse electrolytic cells."

Jan 1, 2015

By F. J. Palumbo

An electronic color-sorting machine was tested for recovering colorless glass concentrates from mixed glass products. The tests were made using glass recovered from unincinerated (raw) urban refuse and residues resulting from the incineration of refuse. The results of the study revealed that concentrates analyzing about 86 percent colorless glass could be recovered from mixed unincinerated glass containing 54 percent colorless glass material. Recovery of the colorless glass was about 62 percent. Color sorting the incinerated glass was somewhat more difficult. Multiple-stage processing was required to recover 59 percent of the colorless glass material in a product analyzing 89 percent colorless glass. The feed material analyzed 41 percent colorless glass.

Jan 1, 1971

By G. H. Keith

A vanadium-base alloy consisting of the following elements in weight-percent--molybdenum, 20; titanium, 10; carbon, 0.1; silicon, 0.5; and yttrium, 0.5--had exceptionally high strength at temperatures up to 1,200° C. This alloy was capable of fabrication to sheet of ~ 1 mm thickness by a combination of hot swaging and hot and warm rolling. In the warm-rolled condition at ambient temperature, its ultimate tensile strength was 1,205 MN/m2. The strength at 1,200° C was 150 MN/m2. Within the temperature range of 25° to 1,200° C, the ductility of the alloy as measured by elongation increased from 4 to >90 percent. Strengthening was achieved by both solid-solution and dispersed-phase mechanisms. Alloys of 20 percent molybdenum and 10 percent titanium were stronger than the other molybdenum-titanium alloy compositions tested. Strength was increased 15 percent in the temperature range of 25° to 800° C, with no accompanying loss in ductility, by the addition of 0.5 percent silicon. Workability was improved by additions of 0.25 and 0.5 percent yttrium.

Jan 1, 1970