Search Documents

By Clarence Zener

THE heat-treatment of steels will not pass from the stage of an art into that of a science until the mechanism of the phase transformations associated therewith is thoroughly understood. Such an under- standing will involve two distinct types of inquiry: (I) the direction of the trans- formation, (2) the speed of the transformation. The first type of inquiry, which involves only the equilibrium relations between the various phases in steel, is the subject of the present and of a succeeding article; the second type, which involves the kinetics of transformations, will be the subject of a later article. In order that a theory of equilibrium relations may give useful information, certain experimental data must be put into the theory. It is customary for these data to be of a thermal nature. In the system discussed here in steel such thermal data are very scarce. In medium-alloy steels another type of data might possibly be used. In these steels the concentration of solute is so low that it may be possible to use the approximation of dilute solutions, an approximation that leads to linear relationships. The unknown functions, or constants, may then be determined in some cases from the binary iron- alloy system and in other cases from the ternary iron-carbon-alloy system. From the functions, or constants, so determined may then be computed the equilibrium relations in more complex medium-alloy steels. In the present article this second approach is used, the necessary experimental data being obtained from the simple binary and ternary equilibrium diagrams. FUNDAMENTAL EQUATIONS In this article are derived the equilibrium relations between the gamma, alpha and cementite phases. In these three phases all important alloying elements except carbon form substitutional solutions, each alloying atom occupying a potential site for an iron atom. Carbon, on the other hand, forms an interstitial solution. In the face-centered cubic gamma phase, the interstitial positions are at the center of the unit cube and at the centers of the cube edges. There are therefore four interstitial positions per unit cell, or one per iron atom. In the body- centered cubic alpha phase, the interstitial positions are probably at the face centers, and also at the centers of the edges, which are crystallographically equivalent to the face centers. There are therefore six interstitial positions per unit cube, or three per iron atom. In cementite, (Fe, Alloy)3C, the carbon atoms may be regarded as filling all the lattice positions of a given type. The introduction of the fundamental equations of equilibrium has presented the author with a quandary. These equations are formally so similar to other equations that have been derived1,2 for related systems that they may appear to some readers

Jan 1, 1946

By Henry D. Hibbard

FoR the purpose of this paper all steels will be divided into two divisions: effervescing and non-effervescing. This classification must be borne in mind as many statements true of one class are not true of the other. Effervescing steels are those that effervesce in the molds, evolving large volumes of gases, which, in escaping, throw up a spray of molten particles of steel and give the molten metal in the mold a rapid stirring or churning motion until it freezes, or, at least, becomes pasty. This effervescing is intended and proper. The non-effervescing steels, which are more or less completely killed, should not evolve any gas in the molds. Many years ago the writer proposed to call the two classes of steels evolution and solution steels, depending on whether the gases in the molds are evolved or kept in solution, but the present designations seem to be better. In America, at least, effervescing steels are in a class by themselves and include steels made for boiler, tank, and ship plates, steel pipe, soft steel wire, wire nails, soft machincry, and structural steels. These are all low-carbon steels with less than 0.40 per cent. carbon. Low-carbon steels that do not effervesce but are killed are also made; these are put into ingots and castings but they are outside the limits of this paper. Effervescing steel is cast into square or slab molds, either top or bottom poured. Most of the effervescing steel is made in the basic open-hearth furnace, though much is made by the acid Bessemer process and a little is made in the acid open-hearth. It is not made by the crucible or electric-furnace process, in which the volume of gas required cannot be produced in the steel and evolved from it in the mold to give the effervescence desired. Any steel ingot, when teeming is finished, is of a certain size or volume. Leaving out of consideration for the moment the lessening of the over-all dimensions of the ingot through contraction due to loss of heat, the ingot may be placed in one of three classes: It may settle, losing in volume; it may stand, that is, remain constant in volume; it may rise, that is, increase in volume. Into which class an ingot will fall depends on the gases of the steel,

Jan 1, 1920

[ ]

Jan 1, 1989

By I M. Platten, S C. Dominy

The evaluation of historical goldfields is currently topical, reflecting a high gold price, improvements in knowledge and technology. and lack of greenfield sites. Many goldfields comprise narrow gold-quartz veins which are structurally complex with an irregular distribution of gold; variable geometry and architecture; and display late deformational effects. The study of historical mine records can be an important tool during early and advanced project evaluation since it contributes to understanding the orebody, exploration target size and setting expectations. The historic Engineer Mine property is located 32 km west of Atlin, British Columbia on the east side of Tagish Lake. The economically important Engineer and Double Decker veins belong to a NNE-SSW vein set. These are narrow, commonly <2 m dilational veins with a minor sinistral strike component and of an epithermal type. Documented ore production between 1910 - 1952 is recorded as approximately 14 263 t at 39.4 g/t Au and 19.5 g/t Ag (for 18 000 oz Au and 8950 oz Ag). The underground workings consist of about 5500 m of tunnels, shafts, raises and stopes over eight levels. The mine is currently being re-evaluated. In 2011, an Inferred Mineral Resource of 41 000 t at 19 g/t Au for 25 000 oz Au (at a 5 g/t Au cut-off) was defined from historical data supported by modern drilling into the Engineer and Double Decker veins. A surface and underground bulk sampling and milling program was undertaken in 2011.CITATION:Dominy, S C and Platten, I M, 2012. Application of historical data to estimate a mineral resource at the Engineer gold mine, British Columbia, Canada, in Proceedings Narrow Vein Mining 2012 , pp 81-100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Nobuhiro Oguma, Yuji Mizuta, Hideya Sato, Shigehiko Iwahori

"Recyclable materials containing copper and precious metals have been treated at the Mitsubishi Process in Naoshima. In 2003, a new incinerating and melting plant (pre-treatment plant) for waste materials, such as shredder residue of automobile and scrapped appliance, was constructed. All of produced slag/metal mixture is treated at the Mitsubishi Process, and which results in the significant increase of recyclable materials treatment. The combination of two processes has realized a highly efficient and environmentally friendly system for recycling valuable metals in the waste which used to be sent to a landfill. Naoshima continues to make efforts to achieve the highly efficient operations of the two processes, and plans to increase the treatment of recyclable materials further. This paper summarizes the recent operations and the various improvements implemented in the pre-treatment plant.IntroductionRecyclable materials containing valuable metals such as copper and precious metals have been treated at the Mitsubishi Continuous Copper Smelting and Converting Process (Mitsubishi Process) since the start-up in 1991. In the early stages, recyclable materials consisting mainly of metal scrap were charged into the process and the treatment had been increased steadily. In order to promote the recycling business, treatment of various kinds of materials including printed circuit boards was started. However, the treatment hit the ceiling due to a limitation of furnace boiler capacity, since they contained large amounts of combustible materials. In addition, severe corrosion of boiler tubes was caused by halogen contained in recyclable materials."

Jan 1, 2012

By William B. Phillips

The possible sources of potash salts in the United States have been considered from many points of view during the last several years, but it is only within the last two or three months that the situation has become acute. We import from Germany, the only sourcc of large supply, more than $10,000,000 worth of potash salts annually, and this business has been badly crippled by the European war. If there was ever a time in our industrial existence when the necessity of providing for our own needs was more acute than it is now, we are not aware of it. One has only to study the price lists of chemicals sent out by the large supply houses to see the change wrought within a very short time. Whether or not these prices are to maintain for a considerable time, no one can say; but it appears to be probable that we shall not see prices materially lower for a period of uncomfortable length, to say the least. It is not my purpose at this time to discuss the various sources of supply of potash salts that have been suggested or recommended. Some of them might afford a pleasing relief but all of them combined would not affect the situation seriously. If we are to have our own sources of potash salts, they will have to compare, in some efficient manner, with the sources upon which we have drawn during the last 20 or 30 years; i.e., they must exist in minable quantities. It seems to me to be quite idle to speculate upon our domestic sources of potash if those sources are not of a character similar to those upon which we have so long depended. A few thousand or, perhaps, a few hundred thousand dollars' worth of chemically derived potash may be produced under the stress of present conditions, but when we consider that each year demands more than $10,000,000 worth, we must look to underground sources; we must look to mines similar to the famous Stassfurt and Halle deposits. If we cannot mine potash salts, we shall have to do without them for a while.

Jan 1, 1915

By Yi Luo

The severity of disturbances caused by longwall mining subsidence to various residential structures can be re¬duced. The success of such mitigation efforts depends on accurate subsidence prediction, correct assessments of the subsidence influences, and careful design and implementa¬tion of the proper mitigation measures. This paper presents the systematic approach involved in the subsidence mitiga¬tion efforts with a case demonstration.

Jan 1, 2003

By T. E. Ackman

The Bureau of Mines conducted a study of current trends in methods employed by the coal industry to dispose of acid mine drainage (AMD) treatment sludge. Thirty-three AMD treatment plants, operated by 11 Pennsylvania coal companies, were randomly surveyed. These plants provided data for calculating sludge volumes, as well as information on sludge settling, transportation, and disposal. Onsite visits allowed observation of problems associated with the various methods of sludge disposal: (1) disposal into a deep mine, (2) permanent retention in ponds, (3) disposal at an active coal refuse area, and (4) onsite burial. Method 1 is the most frequently used and the most environmentally sound. It is apparent, based on this representative sampling of AMD treatment plants, that the magnitude of sludge production is such that an aggressive and directed effort in reduction of sludge volume is seriously needed. The areas of major concern are (1) the amount of surface land required for sludge storage and disposal, (2) reclamation of these disturbed surface areas, and (3) effective and efficient means of removing, transporting, and disposing of AMD sludge. In this report, an engineering approach to the practical problems associated with the existing disposal methods is presented, together with recommendations for future research.

Jan 1, 1982

DISCUSSION, M. Cohen presiding A. H. Geisler and D. L. Martin (GeneTal Electric Research Laboratory, Schenectady, N. Y.)—We were rather interested to note the author's conclusion that the cubic to tetragonal transformation may be of the second order, for we have been able to show that the order-disorder transformation in an analogous alloy system is a first-order transformation with a discon-

Jan 1, 1952

By K. G. Lomberg, M. D. Lionnet

The Bafokeng Rasimone Platinum Mine (BRPM) is a joint venture between Rustenburg Platinum Mines Limited and Royal Bafokeng Resources (Pty) Ltd (Bafokeng). The mining lease has been granted over Boschkoppie 104JQ and is located approximately 10km south of the Pilanesberg Alkaline Complex. The Merensky Reef, which constitutes the principal ore body, is geologically complex. A relationship between its geological variability and the associated mineralisation has been established by defining a number of facies types. The Merensky Reef has been sub-divided into seven distinct facies types: the pegmatoidal facies, contact facies, FW1 pothole facies, FW3pothole facies, FW6 pothole facies, and FW7 pothole facies. The Merensky Reef, which does not form part of the potholed reef, has a large component of footwall mineralisation. The pothole facies, in contrast, has mineralisation located in the hangingwall. Statistical analysis of the facies types indicates that they are unique populations and hence need to be evaluated independently. The mining lease has distinct structural domains that have added additional complications to evaluation of the Merensky Reef. The Merensky facies on BRPM exhibit unique geological and statistical characteristics within well-defined structural blocks. Due to the extreme variability of the Merensky Reef on BRPM a unique approach has been developed, within Anglo Platinum, to evaluate the deposit. Mining cuts are defined and composited for the individual facies types, and then modelled individually by applying known geological controls. The resultant grade models are weighted based on statistical and local geological knowledge. The object of weighting the facies is to replicate the variability observed in the ore body. The introduction of stringent geological controls to the evaluation process has resulted in increased confidence in the in situgrades estimated as an input to the mine planning process

Jan 1, 2006

By J. C. Taylor, J. A. Davis

"Existing environmental, health and safety regulations have forced pyrometallurgical facilities worldwide to drastically change some of their traditional methods of operation. In extreme cases, a number of facilities have been closed due to their inability to conform to these existing regulations. Tougher future legislation and government policy will lead to more stringent regulations and enforcement policies. The efficient control of smelter secondary emissions will, therefore, become critical to successful smelter operation.Much attention has been paid to the smelter primary process off-gas systems, including the development of new process designs to reduce the number of uncontrolled transfer operations. However, even the most modem smelter design requires control of its secondary contaminant sources, which mayor may not be directly related to the process operation.This paper discusses some of the potential secondary emissions encountered in many of the present process technologies. A few of the emission sources presented are only periodic in nature, such as those caused by maintenance procedures, but which have the capability of forcing smelter shut-down because of their direct impact on worker health and safety. The paper deals with a variety of topics relating to the efficient control, maintenance and monitoring of secondary emissions in copper, nickel, aluminum, magnesium and lead smelters, as well as in iron foundries and steel making facilities. Examples of the typical problems encountered in each of the above process operations are presented, including fume control at furnace tapping and slagging locations, metal transfer stations, tapping launders, and ladle transfer operations. The parameters for the most efficient design of fume capture systems, problems encountered with the handling and clean-up of certain collected emissions, and examples of successful solutions in particular operations are discussed."

Jan 1, 1994

By Stephen D. Cramer

The solubility of methane, carbon dioxide, and oxygen was measured in brines at temperatures from 0° to 300° as part of Federal Bureau of Mines research on the corrosion of metals in high-temperature geothermal and mineral processing environments. Solubilities were measured by the technique of extracting pure gas, dissolved at pressures where Henry's law was applicable, from known volumes of brine. The results were smoothed with respect to temperature. The solubility, expressed in terms of the Henry's law constant, reaches a maximum at temperatures ranging from 60° to 100° C for methane and oxygen, and from 160° to 170° C for carbon dioxide. The Henry's law constant increases, that is, gases are salted out of the brines, in the presence of dissolved salts. Salting-out coefficients are strongly dependent upon temperature. The temperature dependence of the Henry's law constant for geothermal brines is different from that for sodium chloride brines owing to the more complex chemistry of the geothermal brines. The solubility of oxygen and carbon dioxide in brines exposed to air saturated with water vapor and at a total pressure of 760 mm Hg is reported for temperatures from 0° C to the normal boiling point.

Jan 1, 1982

By C. F. Cigliana

TO accommodate a large tonnage at high speed from a single level at San Manuel, a very flexible haulage system was designed to give maximum access to stoping areas, minimize delays, and pro- vide for safety. With these requirements as a guide, the haulage was laid out as a simple double loop with one-way traffic of continuous pull. These loops consist of two parallel drifts 100 ft apart, center to center. Haulage drifts are numbered from north to south, the northernmost being the No. 1 drift. This holds true on both the North and South haulage loops. Haulage drifts are connected at 1000-ft intervals with crossovers so that it is possible to bypass any given section that may be inaccessible. Two of these turnouts are double diamonds, one located on the approach to the rotary dumps at the hoisting shafts and the other on the departure from the dumps. The turnout on the approach or North haulage is 835 ft in front of the rotary dump, and the one on the departure, or South haulage, is 1058 ft from the dump. This type of turnout allows trains coming down either haulage drift No. 1 or No. 2 to be routed into either shaft and expedites movement by avoiding delays due to congestion in the dumping area. The double diamond on the return haulage loop facilitates returning empty ore trains to the panels.

Jan 5, 1958

By H. W. Morse

The experimental work on the oxidized copper ore at the New Cornelia mine at Ajo, Ariz., ended on Jan. 12, 1916. On that date final decision was made on the general nature of the process to be used in the 5,000-ton leaching plant, and on many of the details, as far as experience on a 40-ton scale could decide them. With the approval of the Board of Directors and the General Manager, John C. Greenway, we have compiled what seem to be the most interesting data on the results obtained during the experimental period. The most important part of the data resulted from the operation of a 1-ton and a 40-ton plant at Ajo. Experimental work on Cornelia oxidized ore dates back to April, 1912, and has been going on nearly continuously since that time. A good many variations from the original idea have been tried, but the process finally decided upon is in principle and in all of its details a simple one. The history of the leaching work on this ore has been brought down to about a year ago in papers presented to this Institute by Stuart Croasdalel and Dr. L. D. Ricketts.2 The present paper will, therefore, deal principally with the results obtained during the last year of the work. Preliminary Tests by Mb. Croasdale Preliminary tests were begun by Stuart Croasdale in July, 1912. A number of important points were definitely decided by his work. Among these were: 1. New Cornelia oxidized ore, not very finely crushed (to about 2-to 3-mesh) showed good extraction with 5 per cent. sulphuric acid. It appeared that better than 80 per cent. extraction could be expected. 2. The consumption of acid for this extraction was not prohibitive. It was apparently 3.5 to 4 1b. gross per pound of copper recovered.

Jan 1, 1917

By Yoshiaki Fujii

Displacement Discontinuity Method (DDM), which was originally developed by Crouch,S.L., is a powerful tool to calculate mechanical disturbances due to tabular excavations. Three topics on DDM applications to strata control problems in Japanese deep coal mines are described. First, is numerical simulation of microseismicity induced by longwall mining in Horonai Coal Mine. Microseismicity in the mine had been monitored by a mine-wide seismic array. Location of microseismic events and intensity of seismicity were well simulated. In the simulation procedure based on DDM, first, zones where a failure condition is satisfied by the advance of mining are detected. Then, the seismic moments, which indicate the intensity of seismicity, at the failure zones are evaluated. Second, is prediction of the shaft damage due to mining in Sumitomo Akabira Colliery. In this mine, the limit angle of the shaft pillar was changed from 600 to 800 to increase the amount of minable coal volume without increasing mining depth. Displacement of the shaft axis has been measured to assess the damage due to mining around the shaft pillar. In the calculation based on DDM, a fault intersecting the shaft and the ground surface are considered. Observed and predicted displacement of the shaft axis agreed well. Third, is the roadway deformation in Taiheiyo Coal Mine. Attainable maximum stress for a roadway was calculated considering three faults intersecting the roadway. It was realized that the roadway's convergence is related to the calculated stress by simple equations.

Jan 1, 1992

By G. L. Oldright

This paper is the thirteenth of the series on Smelting in the Lead Blast furnace, and the third of the series on Handling Zinciferous Charges. Two other papers have been written on the Rate of Descent of the Stock Column, and Formation of Accretions. These are Reports of Investigations 2963 and 3094, for the Tooele plant and the Bunker Hill plant, respectively.

Jan 1, 1934

By G. L. Oldright

The data in this paper were collected at the Trail smelter of the Consolidated Mining & Smelting Co. of Canada, Limited, through the courtesy of S. G. Blaylock, vice president and general manager; James Buchanan, smelter superintendent; George Murray, assistant smelter superintendent; and the staff members given in Paper XI, Report of Investigations 3243. INTRODUCTION This paper is the thirteenth of the series on Smelting in the Lead Blast Furnace, and the third of the series on Handling Zinciferous Charges. Tyro other papers have been written on the Rate of Descent of the Stock Column, and Formation of Accretions. These are Reports of Investigations 2963 and 3094, for the Tooele plant and the Bunker Hill plant, respectively.

Jan 1, 1934

By C. Clark, J. Seymour, D. Benton

"National Institute for Occupational Safety and Health NIOSH is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics, and alternatives, based on information from injury reports, legacy research, stakeholder input, and published literature. Jackleg drills are involved in more ground fall accidents in underground metal mines than any other drill. Jackleg-related injuries are most prevalent at the face in the course of installing initial ground support. Alternatives to jacklegs for drilling and bolting under incomplete support in narrow underground openings are not yet available. Small mechanized bolting equipment needs to be developed to address jackleg-related accidents and improve safety at mines where jacklegs are being used. JACKLEG DRILL Description The term “jackleg drill” is a generic name for a class of handheld, rotary, percussion rock drills that are equipped with an attached reaction leg to provide stability and thrust for the drill (Figure 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jacklegs are classified according to the bore size of their pneumatic pistons which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in) [Kurt, 1982; Clark, 2012]. Jacklegs typically weigh 460 N (103 lbs), but their weight can approach 535 N (120 lbs) after they are fitted for operation with drill steel and air and water hoses [McKibbin and Clark, 2001]. In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in) diameter holes 1.83 m (6 ft) deep in rock. Application The jackleg drill is primarily used in underground mines when the size of the ore body, the ground conditions, or the mining method do not permit large openings to be mined using mechanized equipment (e.g., narrow vein mining). Jacklegs are used to drill blast-holes for explosives and also holes for installing ground support. These versatile drills are used in nearly all phases of mining including exploration, development, production, and maintenance [Kurt, 1982; Williams et al., 2007; Chen and McKinnon, 2012]. The jackleg is used to drill holes in rock using drill bits attached to hollow steel bars called drill steels (rotary percussion drilling). After the hole is drilled, the jackleg can be used to install different types of ground support components, depending on the ground conditions and the specific ground support measures that are needed. For example, the jackleg can be used to install expansion-anchor rockbolts or resin-grouted rockbolts using the drill’s rotary-motion feature. On the other hand, the jackleg can also be used to install friction-type Split-Set™ rockbolts using the drill’s percussion (hammer-motion) feature. As shown in Figure 1, various washer-like bearing plates can be installed along with these bolts to provide additional ground support and to help secure surface control products, such as wire mesh and shotcrete that are in turn used to retain small, loose material between the bolts [Clark, 2012]."

Jan 1, 2016

El presente texto revisa algunos aspectos del programa de salud ocupacional en las compañías mineras aplicados en el ambiente de trabajo, la explotación de minas y el desarrollo de su control. Primeramente, se describe los riesgos encontrados en las condiciones de trabajo como la composición química del ambiente, la inhalación de polvo y gases en el aire del subsuelo. Como segundo punto, refiere las condiciones de seguridad de la mina, donde se sugiere que el personal de seguridad sea el más idóneo para la dirección del programa de seguridad. Para ello, es importante su capacitación en técnicas de evaluación y control, así como la participación de los médicos de la compañía. Por último, se mencionan algunas medidas de control en las minas, tales como el uso de equipos detectores de gases que determinen los contaminantes sólidos y gaseosos, la compra de un equipo detector de Cu, lámpara de seguridad y la instalación de un equipo de laboratorio químico adecuado,etc.

Jul 20, 1957

By Jürgen. F. Brune, CLAIRE STREBINGER, ADITYA JUGANDA, Gregory E. Bogin Jr

The abstract highlights the risk of methane gas explosions in underground coal mines and the potential of computational fluid dynamics (CFD) modeling to simulate such events and assess their impact on mine ventilation. The study focuses on developing CFD models for large-scale explosions in longwall mines, specifically simulating methane gas explosions resulting from face ignition during coal cutting. The research demonstrates the integration of a combustion model into a longwall mine ventilation model and shows how the availability of explosive gas mixtures significantly affects flame propagation and explosion pressure.

Mar 27, 2022