Search Documents

By L. A. Jordan, D. van Vuuren

A two-dimensional finite difference model has been developed to describe the reduction of kilogram quantities of dehydrated phosphogypsum. The model’s scope has been limited to focus on the heat transfer and reactions that occur within a mass of material contained in a vessel inside a furnace rather than also including the effects of heat transfer to the vessel. Changes in the heat transfer properties (k, ρ, and Cp) are incorporated as the composition of the mass changes as the chemical reactions progress. The model is validated against experimental data, with samples heated to 1000°C at 3°C min−1 while purging with nitrogen gas. A sensitivity analysis of model predictions to the pre-exponential factor of the reaction rate constant of the main chemical reaction and the thermal conductivity of the powder bed indicated that, at the envisaged process conditions, the behaviour of the system depends much more on the rate of heat transfer than on the rate of the chemical reaction. The model demonstrated a significant increase in accuracy when the thermal conductivity was modelled to increase linearly with temperature compared to assuming a constant value.

Oct 1, 2022

By Frederic Souche, Andrew R. Klaetsch, Brian Hann, Nick Goodenow

This paper describes support of excavation (SOE) design and construction for three large diameter shafts excavated through glacial soil and controlled blasting in complex sedimentary rock formations. SOE in soil consists of unreinforced secant pile rings designed to resist lateral pressure in circumferential compression, eliminating costly steel core beam reinforcing. Controlled blasting at the shafts, adits, and tunnels in densely populated neighborhoods requires managing risks to the public, buildings, and utilities. Controlled blasting approaches limited adverse impacts to receptors nearby while achieving adequate production and fragmentation. A site-specific observational approach was used to adjust blasting parameters, limiting the impact on local stakeholders while maintaining daily progress and managing overbreak.

Jun 13, 2023

"Real time analysis of conveyed bulk materials can be used to improve process performance by reducing variability and upgrading ore quality through selective removal of increments of flow that do not meet appropriate selection criteria. This paper focusses on proven Prompt Gamma Neutron Activation Analysis (PGNAA) and microwave transmission technologies used to representatively measure conveyed ore quality in real time so that meaningful decisions can be made between the mine and mill. This enables the effective removal by bulk diversion of small increments of conveyed flow such as waste, highly deleterious material or sub-economic material from the mill feed. Improved ore quality in plant feed optimises process performance, reduces processing costs and minimises tailings generation. Analysis is unaffected by particle size, dust, layering or segregation, mineralogy and belt speed. Technologies are explained and performance examples given from installations in copper and iron ore. The technology has been used successfully in bulk sorting for over twenty years typically using measured increments of a few minutes. Improvements in technology and calibration performance have resulted in accurate measurements over increments of thirty seconds and below.INTRODUCTION Ore quality variability exists on a number of scales. Block model grades represent a few hundred to many thousands of tonnes. Grade control at the mine occurs on a scale typically down to the size of a haul truck, which may be a few hundred tonnes. Highly variable ore quality is detrimental to process efficiency and effectiveness. Processing waste or low grade ore when higher quality feed is available represents a lost opportunity to generate higher revenues earlier in the operational life. Measuring ore quality accurately over short time increments during conveying enables small increments to be measured and diverted according to their quality. The paper explains the technology and benefits. Neutron irradiation techniques were considered potentially suitable for conveyed bauxite measurement by Beurton et al, 1995. Tran & Evans (2001) concluded there was no equivalent technology to Prompt Gamma Neutron Activation Analysis (PGNAA) in terms of material penetration power. PGNAA was evaluated by Nelson & Riddle (2003) for possible use in the phosphate industry and recommended its use for further characterisation of the mine’s various ore types to improve stockpile allocation and grade control. Cottle (2007) discussed test work for an iron sinter application and Delwig et al (2011) described the successful installation in 2009 and performance of PGNAA for base-to-acid ratio control in sinter feed with the analyser output used to control lime addition. Geoscan (PGNAA) works very well on iron ore and can “improve control over what is happening in the plant” and that comfort can be provided in knowing that the product is on-spec according to Minnett (2010). PGNAA is not yet used in the minerals sector for tariff purposes as has occurred since 2000 with Coalscan (PGNAA) in coal (Minnett, 2010)."

Jan 1, 2017

By C. Díaz, M. Barati

Prof. Torstein Utigard's untimely death, in the spring of 2012, put an abrupt end to a meritorious career in the field of high temperature chemical process metallurgy. As an academic in the Department of Materials Science and Engineering of the University of Toronto, Torstein made solid contributions to the advancement of knowledge pertaining to production and refining of both nonferrous and light metals, and to the development of inquisitive and innovative young people in extractive metallurgy. In this profile, the authors highlight aspects of Torstein's rich personality and of his contributions to his field of expertise.

Jan 1, 2015

By FELIPE SÁNCHEZ, PHILIPP HARTLIEB

Innovation plays a critical role in the mining industry as a tool to improve the efficiency of its processes, to reduce costs, but also to meet the increasing social and environmental concerns among communities and authorities. Technological progress has also been crucial to allow the exploitation of new deposits in more complex scenarios: lower ore grades, extreme weather conditions, deeper deposits, harder rock mass, and high-stress environments. This paper discusses the importance of innovation for the mining industry and describes the mechanisms by which it is carried out. It includes a review of the drivers and actors involved and current trends. The digital transformation process that the industry is going through is analyzed, along with other relevant trends that are likely to shape the mining of the future. Additionally, a case study is presented to illustrate the technical and economic implications of developing a disruptive innovation project.

Jul 23, 2020

By S Barrow, D Kent

Controlling the access of equipment, and people, has become more critical over the last few years for improving productivity and to meet safety responsibilities imposed by legislated obligations to have safety management systems. Hence Mine Site Technologies (MST) has spent the last three years completing the development of the tagging system to meet the mining industryÆs requirements, particularly streamlining access control. The basic tagging system tracks active Tags carried by personnel, or attached to vehicles and equipment, within underground zones. These Tags are detected (read) by Beacons placed strategically throughout the mine. As a Tag, or Tags, go past a Beacon they are read and the information transmitted back to the main database PC. This allows the current whereabouts of personnel and equipment to be known, as well as the history of their movements. The objectives of implementing the TRACKER Tagging System at Oaky No 1 Coal Mine were to: maintain a count of personnel inbye a particular point, and can alarm when a pre-set number is reached (eg the limit imposed by availability of SCSRÆs, etc); maintain a count of vehicles (and vehicle type) inbye a point, and can alarm if when a pre-set number is reached (eg when rated diesel units exceeds the limit for the ventilation present in that zone); manage the vehicle fleet, by keeping track of various vehicles underground better control and dispatch management of the equipment is achieved; keep track of equipment, knowing the location of equipment (such as forks, baskets, pumps, fans, etc) where last used or stored will minimise the risk of losing gear and assist in keeping inventory to a minimum; and locate personnel in emergency situations, by placing read Beacons throughout the mine the location of all personnel can be known in real time so that in the event of an emergency, their withdrawal can be monitored.

Jan 1, 2005

By M. Kreuh

Crystalline Mg(OH)Cl and amorphous Mg2(OH)3C1 were successfully isolated from a hydrolyzed molten salt electrolyte sample in this work, It was found that the chemical form and crystallinity of the hydroxylchloride were controlled by the cooling rate of the molten sample when it was taken. Crystalline Mg(OH)Cl could only be obtained by cooling the molten electrolyte sample at a rate not faster than 0.6 °C/min, Upon more rapid cooling, the hydroxylchloride species precipitated as Mg2(OH)3Cl, The behavior of these solid hydroxylchlorides when contacted with fresh and non-hydrolyzed molten electrolyte at 550°C was also examined, It was found that the Mg(OH)Cl rapidly dissolved in the hot electrolyte and did not decompose into MgO at that temperature as would be expected from the literature, The dissolution rate of solid Mg2(OH)3Cl was found to be so slow by comparison that it resulted in the complete decomposition into MgO which thereafter was incorporated into the electrolyte as a suspended solid phase rather than dissolution.

Jan 1, 2004

By A. B. Cecala, G. W. Klinowski

Introduction The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour (acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec (50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average millwide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al., 1987). Testing Total mill ventilation systems were evaluated at two processing operations. For both tests, the primary goal was to determine the reduction in respirable dust throughout the structure. Test site No. 1. The first evaluation was performed at a clay-crushing and screening mill in New York. The mill's base dimensions were 39.6 x 9.8 m (130 x 32 ft), giving a volumetric capacity of 4250 m3 (150,000 cu ft). The TMVS was designed to provide 12 m3/sec (25,430 cfm) of ventilation air to the mill, representing about 10 acph. This was accomplished by three 4 m3/sec (8475 cfm) roof-powered exhaustors that were evenly spaced across the roof. Three wall louvers provided inlets for make-up air at the mill's base. Two evaluations were performed at this mill. The first occurred for two days in December when outside air temperatures ranged from -12.2° to 4.4° C (10° to 40° F). Temperatures with the wind chill factor dropped as low as -34° to -40° C (-29 to -40° F) during the early morning. The second evaluation was in April when outside air temperatures ranged between 10° to 26.7° C (50° to 80° F). These two evaluations verified the effectiveness of TMVS in lowering respirable-dust concentrations throughout the mill. Gravimetric-sampler respirable-dust concentrations in December ranged from 0.22 to 2.39 mg/m3 under normal conditions, compared to 0.13 to 1.55 mg/m3 with TMVS. In April, respirable dust concentrations ranged from 0.29 to 4.84 mg/m3 under normal conditions compared to 0.21 to 2.37 mg/m3 with the system on. TMVS also increased visibility throughout the mill building. Dust reductions for gravimetric and RAM-I instruments are listed in Table 1. Each value was determined by comparing the average concentration for the entire day of testing for normal and TMVS values. The mean/standard deviation values for gravimetric and RAM-1 results were 42.5/17.6 and 37.1/16.8, respectively.

Jan 1, 1996

By A. F. Agnew

Discussion by A.E Agnew Strachan's paper summarizes a wealth of data on water-storage dam "incidents" published by USCOLD and ASCE in 1988, together with a review of tailings-dam incidents published by USCOLD in 1994. The data is summarized by text and 11 histograms. The histograms present a useful compilation of these data, although the patterns within the histogram blocks did not survive the Mining Engineering printing process - so their usefulness is impaired. Unfortunately, the text discussion is too cursory and does not highlight the significant relationships among the various causes of the incidents. Four paragraphs of text and Fig. 1 were devoted to water-storage dams, but the discussion is too sketchy, and Fig. 1 is unclear. Important statistics that could be uncovered are: •the total number of dam incidents tabulated were 500+, •earth embankments constituted 73% of those in operation and •incidents related to earth embankments were 75%, of which dam failures accounted for 24%, major repairs accounted for 42% and accidents accounted for 34%. Strachan concluded that "the majority of the dam failures are associated with overtopping (p. 49), and that the majority of incidents are associated with spillway and other facility structures" - although this is difficult to discern from Fig. 1. Confusion regarding Strachan's use of the terms "dam failures" and "incidents" is compounded by his use of "failures" and "accidents" in one paragraph of his Introduction section followed by his use of "incidents" in the next paragraph. Getting to the meat of Strachan's important paper, the tailings-dam incident survey (USCOLD, 1994), the connection between Figs 2 through 11 seems obscure. First, in the four paragraphs of introductory material, one learns that "incidents consisted of failures, accidents, seepage and other incidents of performance that did not meet design criteria" (p. 50). One does learn the helpful caveat that "structures not related to mill tailings were not included in the review" - so that the Buffalo Creek (West Virginia in 1972) and Aberfan (Wales in 1966) coal-mine failures, together with the ongoing metal-mine remediation work at Summitville (Colorado) do not muddy the waters of his paper. The all-too-brief discussion of the data shown in Figs. 3 through 11 (185 dams in USCOLD plus 26 dams in UNEP) reveals the following: •Figure 3: 57% of the incidents (failures and accidents) occurred with dams less than 20-m (66-ft) in height. •Figure 4: 63% of the incidents were due to failures alone (subset of Fig. 3). •Figure 5: Active dams had 82% of the accidents and 93% of the failures. •Figure 6: Types of dams (upstream, water-retention, downstream, centerline and "unknown") separated according to incidents. •Figure 7: Breaks out the incidents in Fig. 6 by failures, accidents and ground water. •Figure 8: Breaks out incidents by type (overtopping, slope stability, earthquake, foundation, seepage, structural, erosion, mine subsidence and "unknown"). •Figure 9: Separates Fig. 8 data into active and inactive dams. •Figure 10: Separates Fig. 9 data into failures and accidents. •Figure 11: Same as Fig. 8, but broken out by tailings-dam type (Fig. 6). Figures 6 and 7 show that most of the failures are associated with upstream or "unknown" types. Figure 9 shows that the leading causes of incidents for active dams

Jan 1, 2003

By T. H. Etsell, P. Kerr

Over the past 50 years, there have been a number of geological, mineralogical and metallurgical studies carried out on the Clear Hills ironstone deposits in northern Alberta, Canada. Due to the low grade and complex mineralogy, previous metallurgical studies have achieved limited success. After rejecting some of the more ‘conventional’ techniques for iron ore beneficiation, the authors chose to investigate the grain enlargement/iron segregation process for the beneficiation of the Clear Hills ironstone. The segregation reactions for iron have not been explored in as much detail as they have for copper and nickel. Iron segregation roasting involves the addition of a carbonaceous reductant and a chloride transport agent to an iron oxide ore, and heating the mixture to an appropriate temperature. The benefit of this process is that it allows ores in which the value minerals are intimately associated with gangue minerals to be processed in circumstances where conventional iron ore processing techniques are not suitable or capable of upgrading the material. As iron is one of the few elements that can be transported through this process, a clean high purity metallic concentrate can be achieved.Through the use of crucible testing followed by Davis tube magnetic separation, scanning electron microscopy, X-ray diffraction and atomic absorption spectroscopy analysis, characterization of the reaction products has been made with an improved understanding of the reaction mechanism.

Jan 1, 2015

By Richard D. Hagni

Quantitative techniques have become increasingly important in recent years in the study of ore minerals. Precise measurement of indentation hardness and reflectance is the most important quantitative ore microscopic technique for mineral identification. Reflectance measurements of various wave lengths under monochromatic light provide the data necessary for the preparation of spectral reflectance curves and for the quantitative determination of an ore mineral's color. The procedures for the measurement of indentation hardness, reflectance, and color coordinates have recently been standardized and 204 items of quantitative data for ore minerals are now available in the first issue of the quantitative data file of the International Mineralogical Association's Commission on Ore Microscopy. A number of systems utilizing these quantitative data for systematic ore mineral identification have been published and others are in preparation. Rotation properties, although not included on the data cards, are useful in the identification of certain groups of minerals. Other aspects of quantitative ore microscopic techniques include the utilization of automatic image analysis for mineral percentage determinations and the use o~ various microbeam instruments for elemental analyses. These techniques provide a greatly improved basis for mineral identification in mineralogical and beneficiation studies.

Jan 1, 1981

By Oliver C. Fursman, Lloyd H. Banning

This research was undertaken to determine the feasibility of producing steel from hydrogen - reduced , pyrophoric iron powder . Before steelmaking tests were begun , investigations were made to develop procedures for handling the pyrophoric powder safely , and melting tests were made in a single - phase , electric - arc furnace to determine inert gas requirements for preventing powder oxidation . Steelmaking tests were conducted in a conventional electric - arc furnace , usually by a two - slag basic procedure . Results of the research indicated that ( 1 ) pyrophoric powder can be handled safely and can be prevented from oxidizing excessively during charging and melting in electric - arc steelmaking furnaces ; ( 2 ) little , if any , more electrical energy is required for melting Cerro Bolivar iron powder per unit of contained iron than is required for melting heavy melting scrap ; ( 3 ) high - quality steel can be produced readily from high- grade iron powder , having recoveries up to 95 percent of the total iron ; ( 4 ) steel can be produced from simulated titaniferous , chromiferous , and manganiferous iron powders ; and ( 5 ) the electrical energy required for melting increases with increase in the proportion of slag - forming constituents in the furnace charge .

Jan 1, 1964

By V. L. Burdick

A literature review of current uses of Mn02 in ceramic applications with suggestions for future research. Historical background, oceanographic distribution, geology, exploitation, law and politics. Uses of Mn02 in ferrites, semiconductors, catalytic processes, thermo-luminescence and photochromic materials. Select bibliography of 33 items, plus 129 references.

Jan 1, 1980

By Muhammad I. Kabir

The streamline method of recovery prediction reduces a two-dimensional problem to a bundle of one-dimensional ones. This paper presents the development and application of a novel scaling technique which, when used with a streamline model, causes s bundle of one-dimensional problems to further reduce to a single one-dimensional calculation. The one-dimensional calculation accounts for chemical-rock interactions and the streamline model for areal sweep. The scaling technique significantly reduces computation time, is readily modified to desk-top calculations, and can be applied to both absorbing and reacting species. The work was sponsored by the Interior Department's Bureau of Mines.

Jan 1, 1984

By Leo A. Schrider

This report analyzes the successful low-pressure gas drive in the Keener sand of the Bonds Creek oilfield, Pleasants and Ritchie Counties, W. Va.) and predicts its future performance. Core analysis from two wells and electrical and radioactivity logs were used to evaluate the reservoir characteristics. Production records over a 37-year period indicate that over 240,000 barrels of oil have been produced from the Keener sand by low-pressure gas injection. Decline-curve analysis shows that 165,000 additional barrels should be recovered from 108 acres of productive sand by continuing this secondary-recovery method.

Jan 1, 1966

ABSTRACT Inco’s Iron Ore Recovery Plant was operated by Inco from 1955 to 1980 near Sudbury, Ontario. As exposures to specific nickel substances have been associated with adverse respiratory endpoints it is important to understand processes giving rise to such substances. This manuscript discusses the process and equipment, the propensity for aerosol formation, and operational procedures used by Inco in roasting a pyrrhotite concentrate, reducing the nickel in the formed oxide, leaching the nickel in ammoniacal solution, purifying the resulting solution, making green or black NiO, and producing iron oxide pellets. Industrial hygiene measurements are also reported.

Jan 1, 2013

To enable ammonium nitrate-fuel oil (AN-FO) to be used on an equal weight basis with nitroglycerine explosives, smaller diameter bore holes became necessary with consequent modifications to drill steel and burden on holes. Detonation of AN-FO in small diameter holes proved successful both with and without primer charges but some alterations were required to adapt anoloders to the smaller holes.Important factors in training all operators in the new charging method were the retention of improved fragmentation, avoidance of excessive overbreak and keeping wall rock dilution to an absolute minimum. The successful storage of ammonium nitrate in climatic conditions with daily temperature fluctuations above and below the critical 90°F has been achieved.INTRODUCTIONTechnical aspects of ammonium nitrate-fuel oil (AN-Fa) blasting agent are well covered in recent literature. This paper deals primarily with the manner of its introduction as the principal explosive underground at Great Boulder Gold Mines Ltd. and with the many problems encountered in the process. Following reasonably successful experimental firings in June 1962', using granular ammonium nitrate and an anoloder, permission was granted by theWestern Australian Mines Department to carry out test work in selected areas of the mine. The permit allowed for fuse firing only, and for a mixture of AN-Fa containing between 5t and 6 per cent fuel oil, with an adequate primer.The use of AN-Fa on an equal weight basis with nitroglycerine explosives, involved smaller diameter holes with alteration to ground burden and modification to drill steel.Initial tests indicated that it was apparent that AN-Fa could not replace gelignite on an equal weight basis if the...

Jan 1, 1965

By Fanny Herrera, David Reaño, Luis Chahua, Elio Murrugara

El crecimiento del depósito de desmonte Pampa Verde es altamente dependiente de las siguientes restricciones: (1) opciones limitadas para extender lateralmente los contrafuertes existentes; (2) la necesidad de satisfacer tanto la estabilidad estática como la sísmica; (3) la necesidad de seleccionar adecuadamente materiales de alta resistencia para el refuerzo; (4) la importancia de realizar pruebas específicas del material geosintético de refuerzo para caracterizar su interacción con el suelo; y (5) la compleja geometría del sistema en conjunto, particularmente para su estabilidad global. El dique de contención existente fue estabilizado mediante su reforzamiento con geosintéticos, el cual consistió en un relleno de suelo compactado con una talud de 2,1H:1V sobre un muro de suelo estabilizado mecánicamente (MSE o suelo reforzado). La estructura MSE involucra dos muros (superior e inferior) con una banqueta horizontal entre ambos. El muro superior está reforzado con geomallas, mientras que el muro inferior consiste en un sistema Terramesh de gaviones reforzados con geomallas. El enfoque general del diseño consideró el diseño de un talud de suelo reforzado con geosintéticos (TSR) que usaría geomallas de alta capacidad de tracción. Las guías de diseño para el TSR propuesto son las emitidas por la Administración Federal de Carreteras de EE. UU. (FHWA-NHI-10-024). Un aspecto clave a considerar en el diseño propuesto fue la adecuada evaluación de la interfase del suelo contra la geomallama, por lo que se consideró un total de cinco productos de geomalla para su posible uso en la construcción del talud de suelo reforzado con geosintéticos.

Sep 20, 2019

By B. W. Gandrud

The upper part of the Alabama deposits of crystalline graphite consists of an oxidized ore derived from the underlying unoxidized ore through prolonged Weathering. The degree of oxidation in different sections and at different depths within the bed is not uniform. The original ore is hard and blue-gray; the weathered product is soft and brown and is the only part that has been mined to any extent. Samples of both oxidized and unoxidized ores were obtained from two of the large graphite deposits of Clay County. Three additional samples of oxidized ore were obtained from different portions of a third property in the same region. In this report, ores 1 to 5 are of oxidized material and ores 6 and 7 of unoxidized.

Jan 1, 1934

By J. D. Doherty

That America's great coal deposits eventually will be our principal source of liquid as well as solid fuels is generally accepted. Moreover, the day when synthetic oil from coal will begin to supplement our petroleum supplies does not appear to be far off. The American petroleum industry has not spared effort or expenditure in its attempt to keep pace with the demand for oil, and recent production has exceeded expectations. However, the rapidly rising demand for liquid fuels plus the increasing difficulty of finding and developing the new oil needed even to maintain present production rates make it highly unlikely that oil from domestic wells can fully meet future oil requirements. Therefore, it appears that one or more of the following courses must be followed: 1. Curtail oil consumption. 2. Increase imports. 3. Develop new sources such as synthetic liquid fuels.

Jan 1, 1949