Search Documents

By W. E. Coates

The social ecology of surface mining in urban areas is illustrated by a case study of a recent application for the opening of a new gravel pit in the city of Guelph, including the design of a progressive extraction-rehabilitation sequence for the property, investigation of the ecological impact of the proposed operation, history of the application procedure for a zoning change and the relationship of the operating plan to provincial legislation controlling surface mining.

Jan 1, 1972

By John S. Lagarias

While systems to remove sulfur oxides from flue gases have been used at coal fired power plants since 1931, critical need for flue gas desulfurization has only occurred since the late 1960s following the passage of the Clean Air Act Amendments. Commercial and advanced flue gas desulfurization processes (FGD) are reviewed. Advantages and disadvantages of the processes are discussed. Regulatory requirements leading to the development of FGD systems are identified. The location and operation of coal fired plants may be determined more and more by the regulatory requirements for sludge disposal, waste, water discharge and air emissions.

Jan 1, 1978

By John S. Cummings

Although there are many geologic situations which might be discussed at a session such as this, as I considered the problem, it became apparent to me that I should discuss a situation which has been of concern to me, and should be of concern to the geologic community. As a result, the questions which I will pose, and the criticisms, have not been arrived at quickly or easily, but have accumulated through time, to the point where I feel discussion is necessary. Very briefly let me say that my criticism of geologic mapping, of conclusions reached, and objectives or lack of such, results from my association with many areas where such studies have been completed, and resultingly my inability to comprehend the system of evidence or logic which supports extensive age-formational designations. The heart of the problem is that many conclusions resulting in geologic designations are based on weak or non-existent evidence, and such should be catagorized as hypotheses. Although the geologic community as a group does not approve or disapprove of such designations, it is evident that many or most of such designations attain a "status", and arc accepted as more or less valid statements. As will be shown, the amount of specific lithologic data provided in some quadrangle mapping projects is exceedingly slim. However, of concern herein is that the type of information presented at any stage is sufficient to warrant conclusions drawn. To see the magnitude of the problem, it is probably necessary to review some basic fundamentals upon which our geologic systems are established. The United States Geological Survey has defined a "formation" as the broad unit of geologic mapping consisting of a large and persistent stratum of one kind of rock. Obviously such a designation allows that a formation could be considered "time variant" in a horizontal as well as in a vertical context. However, other definitions enable a formation to mean units

Jan 1, 1972

By Kevin Galvin, Simon Iveson

Fine particles are the most valuable because they are the most liberated. However, they are also the most expensive and difficult to recover and concentrate. The Reflux Classifier is a novel invention that combines many of the virtues of existing fine particle separation technologies in a way that provides profound synergies. Multiple parallel narrow channels create a laminar-shear separation zone. The laminar flow provides a well-defined velocity gradient that exposes particles on the wall to a conveying velocity that is approximately proportional to their size, thus reducing the dependence of elutriation velocity on particle size. The high shear rate in these channels generates a hydrodynamic lift force that selectively lifts low-density particles off the channel wall and thus causes them to be preferentially conveyed out in the overflow. Particles that are not elutriated slide back down into the mixing reflux zone beneath the inclined channels which gives them multiple opportunities to re-enter the channels. The resultant suspension of both coarse and fine high-density particles in the fluidized bed zone at the base of the unit generates a strong autogenous dense medium that helps to direct large low-density particles back up to the overflow. The fluidization water also simultaneously de-slimes the high density underflow product. When placed in a centrifuge, the benefits of these features multiply with the improvements in capacity and selectivity that arise from high G-forces. When inverted, these features can be used to perform flotation well beyond the conventional flooding limit. Hence this invention platform has the potential to dramatically improve both gravity and flotation separation performance across the minerals processing industry.

Jan 1, 2014

By A. Wahab Khair

"This paper presents an analysis of fracture mechanisms in coal subjected to bi-axial state of stresses, indentation of laterally confined coal specimen. Coal specimens were loaded to failure by the straight wedge indenters at various lateral confinement pressures. Strain distribution and acoustic emission characteristics of coal specimens under stress were recorded. The influence lines of vertical forces acting on the horizontal straight boundary of the coal specimen for each type of wedge indenter have been established using holographic interferometry technique. The effects of wedge indenter angle, confinement pressure, and coal anisotropy on fracture types, failure modes, and post-failure conditions were studied. The results indicated that combined application of holographic interferometry and acoustic emission monitoring techniques is not only suitable ·for studying deformability of heterogeneous and microscopically discontinuous material under stress but it also enhances the mode of fracture during the post failure stage. INTRODUCTIONOne of the relevant processes in the coal cutting technology is the application of indentation theories. Since most cutting tools in the coal industry are wedge shaped most of the indentation research is found for a wedge shaped tool.A wide range of behavior is found in different rocks subjected to the wedge penetration. A rock which is elastic brittle at standard pressure might become elastic plastic at high confining pressure (Gnirk and Cheatham, 1963). It was also observed that some rocks will merely be crushed and indented by a wedge whereas others will crack and form chips, furthermore the existence or non-existence of chips depends mostly on the geometry of the indenter, type of rock and the depth of penetration (Evans and Murrel, 1958). However, coal cutting technology is mostly explained by models which use rigid wedge to penetrate into a brittle material in which both crushing and chipping will occur (Evans and Murrel, 1958, 1962)."

Jan 1, 1988

By Kenneth S. Ritchie

TOO often, many foremen; superintendents, managers, and executives, "The Bosses" of the oil and mining industries, do not fully realize: (1) How much personal actions '.on the job" may reduce their effectiveness in getting work done; and, (2) The importance of harmonious relations with their fellow men. Today. these qualities of personality in the people entrusted with the positions of responsibility are more important than ever with the shortages of labor so critical in vital war production. Likewise, many engineers do not fully realize that their work is essentially executive in character; i.e., other people do the actual labor. Without their help. the engineer's work would not be done. A clearer appreciation of this fact would increase their interest: (1) in the nontechnical aspects of their work. and, (2)in their relations with others, particularly the individuals in their own organization. Consequently, these engineers would be more successful in equipping themselves for greater responsibilities and increased remuneration.

Jan 1, 1944

By AIME AIME

MOST recently elected to the limited group of Honorary Members in the A.I.M.E. is the distinguished Australian metallurgist, Guillaume Daniel Delprat. His citation reads: "in recognition of his distinguished achievement as metallurgist, engineer, and administrator in the production of ferrous and nonferrous metals," Mr. Delprat's ability and experience in both the ferrous and nonferrous fields at once distinguishes him from most of his professional brothers. Mr. Delprat's nativity was neither Australian nor English, for he was born in Delft, Holland, in 1856, and educated in Amsterdam. At the age of 22 he went to Spain, as metallurgist for the Tharsis Sulphur and Copper Co., Ltd. Afterwards he spent some time with the Bede Metal and Chemical Co., which had mines in both Spain and Norway, and of which company he became general manager. Other positions of responsibility held by Mr. Delprat before he went to Australia included the managing directorship of the Cordova Exploration Co., with properties in Spain and Canada; of the Rincon Silver-Lead Mining Co., in Spain; and of the Deloro Gold Mines, in Canada.

Jan 1, 1936

By E. P. Youngman

This digest, based upon a translation" of certain portions of the 1930 law, covers the pertinent points of what has been termed "The New Mining Law of Luxemburg," the Grand Ducal Order (Arrêté) of April 26, 1930, concerning the exploitation of "mines, minières, and carrières, 4 and abrogating the order of January 2, 1891, concerning the same subject." The Duchy of Luxemburg, which between 1735 and 1815 was French, adopted as its basic mining law the French Law of April 21, 1810, and an Imperial Decree of January 3, 1813. The Luxemburg Government later supplemented and modified this legislation by the laws of June 12, 1874, April 30, 1890, and May 10, 1898, which, with article 36 of the Constitution, are to be taken into consideration in a complete survey of mining legislation. The order of

Apr 1, 1933

By Margaret N. Maxey

For the past quarter century, it is fair to say that the political agenda of Western industrialized societies has been driven by those opposed to forms of economic growth providing sustenance to a growing population. They regard growth as the major threat to their social philosophy which champions a wholly "new ethic of biocentric equality" or "living as if Nature mattered." This ethic demands that "a violent, plundering humankind" must abandon its alleged rape of Planet Earth and derive its ethical norms from pre-existing harmonies and fragile, precarious balance present in Nature. A Green political agenda appeals strongly to deep longings shared among many people whose temperament seeks tranquillity in a world of wild natural beauty uncluttered by dependency on tools and experts and specialists. According to proponents of the Green philosophy, our world is pregnant with enormous problems. Armed with expanded political powers, regulatory guardians at state and local levels have mustered their forces with shotguns cocked, poised to prod an ignorant and lazy citizenry to the altar for an exchange of vows with Environmental Ethics. Social engineers have skillfully discredited the traditional role of professionals in scientific engineering who are summarily dismissed as the failed architects of an industrial system pillaging the earth. They stand accused of producing unmanageable offspring - from mining minerals and energy resources to disposing of toxic wastes - whose disputed parentage and expectant crimes against humanity must be prevented by removing them from normal custody. Green critics claim that markets cannot be given custody of industrial offspring - pollutants, wastes, land-use abuses. Markets appear to have failed to provide equity to present and future generations. The only custodian with sufficient coercive power seems to be the regulatory bureaucracy. The upshot is a stark Hobson's choice - Shotgun Wedding vs. Custody Dispute. It derives its fateful predestination from an uncritical acceptance of several preconceptions which currently undergird the altar of Sustainability characterized by its acolytes as "a new and exciting doctrine." It is significant that Limits to Growth slogans of the 1970s have been displaced in the 1990s by the more palatable language of Sustainability. As a policy recommended to forestall an impending doom, Sustainability derives its credibility from dire predictions of global warming, ozone depletion, acid rain and the like. The Rio Declaration announced to the world in June 1992 that, although energy is essential to human well-being, its production and consumption in wealthy industrialized nations is unsustainable. It called for a complete overhaul of energy systems with nothing short of a total replacement of fossil fuels, uranium fission reactors, and large hydroelectric projects by means of so-called renewable energy sources, augmented by coercive regulations to force conservation and limit consumption demands. The social and political consequences of such a sweeping

Jan 1, 1995

By Tony Amis, Marco Barla, Alice Di Donna

"Energy geostructures are becoming an increasingly popular solution around the world for Developers looking to reduce CO2 and system running costs. Energy geostructures are geotechnical structures that provide both the important role of structural stability while also acting as a heat exchanger with the ground, enabling the supported buildings and or infrastructure to be heated and cooled using the principle of low enthalpy geothermal systems. The main advantage of this innovative technology with respect to standard geothermal plant is the reduction of the initial installation costs and construction schedule benefits, compared to installing conventional geothermal solutions, largely due to the additional use of structures which would be constructed in any case. However, it is important with respect to energy geostructures that additional aspects need careful consideration. For this very reason, several research studies have been carried out over the last decade on this subject and a number of real case studies have been monitored and analysed. The key difference with respect to conventional shallow geothermal systems are mainly related to the geometry, which is imposed by the geotechnical project, and the need to ensure that the primary structural role is always guaranteed. Special boundary conditions, the reduced depth, the influence of atmospheric external temperature can also play an important role for energy geostructures. They can affect, both energy efficiency and, the geotechnical behaviour because of the possible thermal induced mechanical effects. This paper presents a picture of the current situation regarding energy geostructures and their peculiar features, and collects available data to provide a reference framework. Data has been collected from literature and personal communications and then processed to provide easy-to-read charts useful for practical consultation at a glance. This paper provides, an indication of the distribution of such systems worldwide, their spread in time, and a global view of their actual efficiency from the structural, energy, economic and environmental point of view.1. IntroductionEnergy geostructures are becoming an increasingly popular consideration around the world. Energy geostructures are geotechnical structures with a dual role of providing structural stability and the ability to exchange heat with the ground, to provide low carbon heat and coolth to supporting and or adjacent buildings and infrastructure, using the principle of low enthalpy geothermal systems (Barla and Di Donna, 2016; Laloui and Di Donna, 2013). A closed circuit of high density polyethylene (HDPE) pipes is embedded in the concrete, and a heat carrier fluid circulates through them exchanging heat with the ground. The HDPE pipework circuit inside the geostructure is linked to one of the above buildings or infrastructure through a heat pump, which adapts the temperature of the circulating fluid to the heating (winter mode) and cooling (summer mode) needs. In this way, heat can be injected into the ground during summer and extracted from it during winter. In principle, all structures in contact with the ground can be used as energy geostructures. The first examples of energy geostructures date back to the eighties in Austria and were mainly piles and shallow foundations. A decade later, Henderson et al. (1999) reported on what would appear to be the first successful use of geothermal energy piles in the US, with loops incorporated into the foundation for a hotel in Geneva, New York. As was their use in this New York case history, the typical geothermal energy pile application is used in conjunction with additional closed loop boreholes to provide the required energy capacity for a structure. Interestingly the report concludes that the geothermal energy piles had a better heat transfer performance than the borehole field. The first energy walls appeared slightly later, while still today only a few experimental cas"

Jan 1, 2017

By Lourens Scheepers

Mining induced seismicity and rockbursts have been part of the deep level gold mining industry in South Africa for many years. One could be forgiven for thinking that we should know everything there is to know by now to have rockbursting under control to a level that it has minimal impact on safety and production. Well, we don’t… There are things we know that we know, and they are implemented, or should be. There are thigs we know that we don’t know, and they are researched, or should be. There are things we don’t know that we don’t know, and, well, we don’t know… We know that seismicity and the associated potential for rockbursts generally increase with an increase in stress (increase in mining depth and/or mining span and creation of remnants) and proximity to faults and dykes. We know there are a number of potential sources of events in a mine; that is: mining abutments, pillar abutments, mining faces and geological structures (faults and dykes). We know there are a number of event mechanisms associated with these sources; that is: slip on a geological structure, shear through intact rock and bursting of the rock near the edge of a mining excavation. One of the tools used more and more and with increased success to identify event source mechanisms is Moment-Tensor analysis (MT). This typically assist in differentiating between three event mechanism components: volumetric deformation component, axial deformation component and slip / shear component. The insight gained from MT assist greatly in identifying the most likely event source to assist in understanding the rockmass response to mining. We know that the seismic response in our mines are mining induced (not natural). This may seem trivial, but it is important to realise that we influence the seismic response with the way we mine, and by how much we mine (extraction ratio). Therefore we put design rules and strategies in place to reduce the seismic hazard and we install rockburst support in our mining excavations. We know the seismic response to mining is influenced by the properties of the rockmass, including strength, stiffness and brittleness, but quantifying its influence is typically more difficult than expected. We know numerical modelling can improve the engineer’s understanding of the potential rockmass response associated with designed mining layouts and strategies. For our environment (narrow, tabular large area) elastic boundary element modelling remains the most convenient and practical approach, but it overestimates the stress at mining abutments and underestimates the stress further away from these abutments. Adding a crushing (based in limit equilibrium) modelling approach vastly improves the boundary element modelling ability to simulate the deformed (interpret fractured) zones and associated redistribution of stress. We don’t know how to quantify what an acceptable seismic risk is. We don’t know if we can mine remnants at an acceptable seismic risk. Some remnants are extracted surprisingly easy, others serve us with devastating rockbursts. The limit equilibrium modelling shows potential to significantly improve our ability to quantify the rockburst risk. We don’t know if large-scale preconditioning is possible and will be effective to significantly reduce the seismic risk associated with remnant and pillar mining. Research is required (and has been initiated). Vast areas of ground have been extracted historically in the South African gold fields. Most gold reserves are now in deeper ground (4000 m) and historic remnants (areas left before due to mining difficulties) as well as pillars (regional stability pillars). If we cannot find ways to extract these reserves at acceptable risk levels, the future of the South African gold mining industry is very short.

Apr 26, 2022

By Duncan M. Lamb

Commercial computer "time-sharing" is a new and powerful tool for the engineer. It is a system of virtually simultaneous use of a digital computer by several individuals. Access to the computer is by means of a conventional teletypewriter which transmits over the regular telephone lines to the computer which may be located any distance from the user. Complex or repetitive computations can be programmed and the speed of computation is many times that which one can do with slide rule and desk calculator. The availability of such a commercial computer "time-sharing" system offered an opportunity to transform a tedious and time-consuming task into one that requires only a few minutes. Until the work of F. C. Bond produced widely accepted mathematical statements concerning the performance of grinding mills, the selection of the proper size equipment was done by comparison with similar operating equipment. Allis-Chalmers systematized Bond's work in a bulletin published in 1963 but the calculations are laborious and the final mill selection still required comparison of the calculated power draw with the power requirements listed in equipment catalogs. This was, however, a step forward from previous procedures. This paper discusses a rapid and simple method of determining the size and power requirement of overflow ball mills. A shared-time computer program has been developed which rapidly calculates and displays the physical dimensions, power requirements, grinding media size and quantity, as well as the important correction factors used. All of these data are calculated from input information which is usually available.

Jan 1, 1969

By G. S. Rice, R. V. Wheeler

"FOREWORDThe cooperative mine safety research program was carried on successfully in the year 1930 in a manner similar to that described in the report for 1929It is believed that the results of such fundamental work as is being done are unquestionably of great benefit in their application in coal-mining operations, in the saving of life and health of minera. The research result compared and checked by investigations in the two organizations, and further by large-scale tests, as in the Experimental Mine, give confidence to mine operators, miners and State mining officials in the findings of the various researches.The annual report of the contact officers of the United. States Bureau of Mines and the British Safety in Mines Research Board to the Director of the Bureau and the Chairman of the Board respectively, follows:Annual Reports for 1930 To: The Director, Bureau of Mines.The Chairman, Safety in Mines Research Board."

Sep 1, 1931

By P. B. Altringer

The Bureau of Mines conducted laboratory tests to devise a procedure for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 parts per million of tungsten (70 parts per million of W03). Using ion exchange resins synthesized by Bureau chemists, 98 percent of the tungsten was extracted from the brine and 92 percent of the tungsten was recovered as a marketable iron-tungsten concentrate containing 44 percent tungstic oxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process-development unit to provide more reliable data for an economic appraisal.

Jan 1, 1978

By Zhiqiang Zhou, Shengnan Zhou, Zizong Zhu, Yuchuan Ding

The effect of silicon on removal of phosphorus from high phosphorus Si–Mn alloy was investigated at 1673 K by CaO-based slag. It was found that the dephosphorization efficiency increases significantly as increasing the silicon content, which is due to the reaction between silicon and CaO at slag/alloy interface. The relation between silicon content with oxygen activity and phosphorus activity coefficient of Si–Mn melt was determined respectively as follows: lg aO = -1:55xSi - 1:67; ln rP = 9:26e xSi 0:0433 + 11:0839 The carbon content in Si–Mn melt decreases continuously with the increasing silicon content, meanwhile, the decreasing rate of carbon content becomes rapid when the mole fraction of silicon is about 0.32. Si addition is beneficial for both dephosphorization process and low carbon Si–Mn alloy production.

Mar 1, 2017

By M. N. Barbier

Según la obra del Ministerio de Educación Nacional de Francia existen 112 escuelas de ingenieros que este año formarán total alrededor de 6.000 ingenieros. Sin embargo, surgen algunos problemas en la formación de esta profesión como: aquellos ligados al reclutamiento de los alumnos de las escuelas de ingenieros, para obtener el mayor número posible de alumnos jóvenes y bien preparados, y los relacionados a la actividad misma de las escuelas de ingenieros, tales como programas, métodos de enseñanza y relaciones con la industria. En ese sentido, el presente texto revisa dichos problemas y plantea soluciones respecto a ellos como: diversas mejoras en el régimen de los concursos de las grandes escuelas y duracíón de la preparación, así como una reducción del número de materias enseñadas y la adopción de métodos activos de la enseñanza en lugar de aquéllos que se limitaban a exigir la presencia física de los alumnos.

May 1, 1965

Jan 1, 1885

By J. A. Eisele

The Bureau of Mines conducted bench-scale cyclic tests to determine the composition of recycled leach liquor in the Bureau?s proposed clay/HCl leach/ HCl sparge process for producing Al203 from clay. The data developed from these tests make it possible to synthesize leach liquors for predetermined steady-state operating conditions when conducting large-scale crystallization tests. The results of two sparge tests were compared. One was a 20-cycle test with a 36-pct-HCl concentration in the mother liquor; the other was a 10-cycle test with a 26-pct-HCl concentration in the mother liquor. The effect of impurity concentrations in the leach liquor on the purity of aluminum chloride (AlCl30?6H20) crystals was determined, but there was poor correlation between this data and results that have been obtained from miniplant-scale work.

Jan 1, 1980

By George A. Miller

OIL, the abundance of it in the hands of the Allies and the lack of it in the hands of the Axis, played a major role in winning World War II. It bids fair to implement the winning of the peace. In fact the signing of the revised agreement on petroleum between the Government of the United Kingdom of Great Britain and Northern Ireland and the Government of the United States of America on Sept. 24, 1945, may be considered as the first step in establishing a new pattern in foreign relations by our Government. The significance of this agreement on petroleum is that it was arrived at on the part of the United States of America through the advice and consent of the most interested parties, the leaders of the petroleum industry and the Government, distinctly a first step toward unifying the power of business and the strength of the Government, which places us on a par with the British Crown which has always had the advice and counsel of its business leaders in formulating its foreign trade policies. And what is the thing so patently discernible in this new first step toward winning the peace? It is that the petroleum agreement, the first draft of which, signed in Washington on Aug. 8, 1944, almost caused an epidemic of apoplexy among the leaders of the oil industry, represents the desire of the people most concerned with the problems of petroleum both at home and abroad. This new agreement, which will come up before the Senate for ratification this month-hearings will commence in January - derives its "power from the consent of the governed," something about which our forefathers were vitally concerned once upon a time.

Jan 1, 1946

By Hani Henein, J. Barry Wiskel

"The easy accessibility and power of the PC, as well as the education of our engineering students in the use of these tools, are compelling reasons for developing computer aided instructional (CAI) tools. There are a wide range of areas in the engineering curriculum where students must learn the steps and the process of applying judgement in problem solving. In the typical course instruction, · an instructor introduces theory to students; the application of the theory to solving problems is often demonstrated in the abstract. Students therefore spend a significant amount of time learning how to apply the theory to problem solving. Additional time and effort must then be spent to get students to the point of learning concepts and integrating this knowledge. A number of computer aided packages have therefore been developed for use in several courses in the materials science and engineering curriculum that encompass both calculational and instructional capabilities. This paper presents an overview of some of these packages which include the solution of a non-linear equation, the instruction of binary diffusion couples, an introduction of crystallography, an introduction to heat transfer and the solution of thermodynamic stability diagrams. The context in which these CAI Tutorials were developed and are being used will be discussed. The pitfalls in the development of these packages will also be discussed. The use of the tutorials has important implications on the expectations from an engineering education of both instructor and student.IntroductionTraditionally, it is quite routine to teach engineering students how to use a computer (the PC today for undergraduates) as a tool in performing engineering calculations or in simulating a process or a unit operation. This often takes the form of one course in computer programming, whether it is Fortran, Visual basic or a spreadsheet, and another course in numerical computation. However, the materials and electronic revolution have brought about considerable advances in computer power and speed, and accessibility. Today, the manipulation of digital images, movies, and speech are commonplace on a desktop PC.' Many mathematical models that were executed only on workstations can now be readily handled on a PC. Concurrently, more of our students own a PC even if their curriculum does not require them to purchase one. Today, virtually every university student has been introduced to the PC in either their elementary or high school education. Hence, the increased capabilities and accessibility of the PC and the familiarity of students with this tool make it compelling to explore its use as an educational tool for our engineering students. This is not a traditional role of a computer in our engineering curriculum."

Jan 1, 2000