Search Documents

By Arthur C. Green

A group of 13 cities situated in Los Angeles and Orange counties in Southern California is engaged in constructing an aqueduct to carry water from the Colorado River at a point near Parker, Arizona, to a distribution point near Riverside, California. The aqueduct will have a total length of approximately 241 miles, and is designed to deliver 1605 cu. ft. of water per second, or a little more than one billion gallons per day. The aqueduct crosses a barren, desert waste and the project includes approximately 91 miles of 16-ft. tunnel. The large amount of tunnel driving that has been done in this country in the past few years has resulted in some remarkable developments in equipment and methods. The building of the Colorado River Aqueduct,, with its 91 miles of tunnels, has called on the best engineering knowledge in the country. New and better equipment has been designed for all phases of the work, and this equipment has been coordinated and adapted to the various conditions with a high degree of efficiency. The result has been that records for tunnel driving have been set under adverse natural conditions that exceed the estimates for progress under good conditions. All of the tunnels in the main aqueduct, except the Valverde and Bernasconi at the western end, have a finished diameter, inside the concrete lining, of 16 ft. Fig. 4 shows a section of the tunnel with the concrete lining in place. Fig. 5 illustrates the finished tunnel in three typical sections. The standard tunnel grade is 3.432 ft. per mile in the 16-ft. tunnels, but the Valverde and Bernasconi tunnels have a steeper grade and a finished diameter of 15 ft. 3 in. The rough bore of the large main aqueduct tunnels averages 12.95 solid cubic yards of material per foot of advance in timbered sections and 10.76 solid cubic yards per foot in unsupported sections. Tunnel Driving While the Conway mucker has been used on tunnel work for years, a larger and more powerful Conway was designed to meet the require-

Jan 1, 1937

By O Tiili, A Dixon

Many minerals processing plants need to have greater efficiency in current times and optimise their process performance in order to maintain high profitability. This is even more so in the current economic climate. In the case of large flotation cells, such as TankCell«-300 with over 300 m3 active capacity, ensuring consistent operation and optimal flotation conditions is particularly critical, given the high impact on overall process and throughput of such cells. As there are fewer cells to control and monitor, there is also a lower initial capital cost for instrumentation - the requirements, however, are higher. Despite such compelling reasons, instrumentation and basic control in flotation cells has not changed much in recent years. The standard is still to use traditional feedback (PI algorithm) controls for slurry level and flotation air. A new advanced instrumentation and control package for large flotation cells has recently been developed by Outotec and has been installed at Macraes.In addition to the standard basic instrumentation and control, the new system at Macraes consists of a froth image analysis system, a froth velocity control, and a level control system which utilises adaptive feedforward compensation. There are three TankCell«-300 cells in operation at Macraes since November 2007 and the new control system was commissioned in December 2007.The paper will include comparative data from pre- and postsystem installation and discusses benefits including optimised recovery, improved performance, as well as ease of operation.

Jan 1, 2009

By Yves C. Lizotte, Malcolm J. Scobie

Blast fragmentation is affected by the physical and mechanical characteristics of the rockmass as determined by geology as well as the explosive energy, the partition of this energy, the actual amount of energy transmitted to the rockmass, the blast geometry and the detonation sequence. This paper reviews studies of the influence of geology on blast fragmentation, particularly structure, i.e. the in situ or inherent fragmentation arising from rock discontinuities. Prior structural studies have mainly been limited to comparing equivalent diameters of the in situ blocks with the size distributions of the blasted material. No criteria exist to integrate structure into blast design. This paper reviews on-going studies of the blasted fragment shape and size observed in different rockmasses aimed at analyzing geological control over blasting. Digital photoanalysis was applied {o measure size and shape distributions, to correlate results with block size distributions and shape parameters of the inherent fragmentation. An integrated and comprehensive fragmentation assessment procedure which accounts for geological control is proposed. The potential of this research is to provide a greater understanding of the true contribution of explosives to fragmentation, the effects of fragment shape on system productivity and the reduction of blast-induced damage.

Jan 1, 1994

By W. M. Robertson

The rate of crack Propagation thvough a solid meta1 in the presence of a liquid metal has been calculated. The crack is assumed to propagate by solution of the solid in the liquid under the influence of an applied stress, with volume diffusion of the dissolved solute through the liquid controlling the propagation. The calculated velocities can be tens of centimeters per second or higher. THE embrittlement of normally ductile solid metals by liquid metals has been the subject of extensive study, as summarized in the book by Rostoker, McCaughey, and arkuus.' In experimental studies of liquid-metal embrittlement it is usually concluded that the observed crack-propagation rates are too high to be accounted for by diffusion processes. Diffusion is considered to be an unimportant factor and various other mechanisms are invoked to account for the experimental observations. The similarities of liquid-metal embrittlement to stress-corrosion cracking, to hydrogen embrittlement of steel, and to low-temperature embrittlement of bcc metals are frequently used as analogies for these mechanisms.1"3 The present paper assesses how rapidly a crack could propagate by a mechanism of volume diffusion through the liquid metal. We assume that the crack propagates by solution of the solid in the liquid at the crack tip under the influence of the applied stress and diffusion of the dissolved solute away from the crack tip. The model uses only macroscopic thermodynamic, kinetic, and elastic concepts. The calculations indicate that this dissolution-diffusion mechanism can give high crack velocities. In some previous treatments4'' of crack propagation in a liquid-metal environment the fundamental step has been the breaking of atomic bonds at the crack tip. The liquid greatly decreases the energy necessary to break these bonds. The present model assumes the crack is filled with liquid metal; the presence of the liquid is essential because diffusion through the liquid is assumed to control the rate of propagation. With proper modification this model could also apply to stress corrosion in a liquid environment. THEORY Consider a crack in a homogeneous elastic continuum, ignoring all the structural details of the solid. This neglects a host of metallurgical details which can be significant in the problem of liquid-metal embrittlement;' but this simple assumption is a useful approach in evaluating the role of diffusion through the liquid. The stress distribution around the crack tip establishes a gradient in the chemical potential at the tip, which causes a diffusion flux through the liquid away from the tip. The solid-liquid interfacial tension works against crack propagation, since propagation requires creation of interfacial area. From these two considerations we derive the diffusion flux, which then yields an expression for the velocity of the crack tip. The concentration of the solute in the liquid, C, is equal to the equilibrium concentration in the presence of an unstressed, flat surface, Co, plus the excess concentration due to the stress, AC(a), plus the excess concentration due to capillarity, AC(y): We calculate AC(o) and AC(y) and then obtain the diffusion flux. Consider (Fig. 1) a long flat crack of length 2L, thickness 2r, and tip radius r, where r remains constant as the crack propagates in the positive x direction. There is no stress ay in the y direction across the flat surfaces of the crack. The magnitude of the stress at the crack tip due to the applied stress, a,, is given by the relation6 ^=^[l-2^] 12] which, for long narrow cracks, becomes The stress increases the chemical potential in proportion to the strain energy.? The excess chemical potential due to the stress, Ap(a), is given by where 52 is the atomic volume of the solid and E the Young's modulus. Inserting Eq. [3] gives Now consider the crack to be filled with a liquid metal. The excess solubility due to stress, hC(a), is given by the excess chemical potential due to capillarity, Ap(y), is given by8 where y is the solid-liquid interfacial energy, and v1 and YZ are the two principal radii of curvature of any surface point. At the crack tip, r1 = -r and vz = m, so TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME

Jan 1, 1967

By Rod Maclean, George Stewart

"This paper covers the planning, development, and mining of an underground pillar complex using a bulk mining method. To achieve the long-term goal of continually improving our operating processes, all cut-and-fill and undercut-and-fill workplaces at Thompson Mine have been evaluated for their conversion potential to the bulk method referred to as VerticalBlock Mining (V.B.M.).Since December 1979, conversion has occurred to the extent where 80% of the ore hoisted is mined using Vertical Block Mining (V.B.M.).Productivity and profitability have been substantially improved by converting to this bulk method, especially in pillar areas.IntroductionThompson Mine is a 6000 ton per day underground nickel mine located 3 miles outside the City of Thompson, 400 air miles north of Winnipeg . The mine has two shafts, T-l and T-3 (Fig. 1). The T-l shaft is 4427 feet deep with the deepest mining taking place on 4000 level. The T-3 shaft, which is the area of this presentation, extends to a depth of 2607 ft with the deepest operating level at 2400 ft. The two shafts, some 10 000 ft apart, are connected underground on numerous levels. The ore mined at T-3 is trammed on 2400 level to the T-I main ore pass and hoisted through the T-l shaft. Eight hundred and fifty thousand cubic feet of fresh air per minute ventilates the mine.The 1400 level 310 pillar complex is located in the T-3 mine area. There are six rib pillars, two crown pillars and one main pillar (boundary pillar between cut-and-fill stopes) within the complex (Fig. 2). The majority of the ore in this area has been mined using mechanized cut-and-fill techniques .Undercut-and-fill mining was the method originally planned to recover these pillars. It is slow, labour-intensive, and requires extensive use of timber during the mining cycle. The extraction drifts in the area are heavily timbered due to their proximity to the ore and the age of the facilities. Increasing drift maintenance costs and the successful mining of two main pillars with V.8.M. techniques provided the stimulus to review the mining plans for this area."

Jan 1, 1988

By Stuart Croasdale

Not long ago I was called upon to conduct some experiments on the treatment of ores from the New Cornelia copper mine, Ajo mountains, Arizona, for the Calumet & Arizona Copper Co. The problem was a very interesting one and contained some unusual features. Incidental with this problem was the utilization of a large amount of low-grade pyrite in the Bisbee mines of the company, provided this could be accomplished by any feasible method. The New Cornelia mine is situated 45 miles south of Gila Bend, the nearest railroad point, on the Southern Pacific Railroad. It is about 160 miles, almost due west, from Tucson. This section is one of the most arid in the United States. The normal annual precipitation, as given by the United States Weather Bureau covering a period from 1870 to 1901, is 3 to 5 in. During June and July, 1913, the records kept by the company gave the following results. These are all I have available, but they show the enormous evaporation that can be expected, which may be a factor in leaching operations on a large scale. Temperature, Degrees F. High Low Average June...................... 112 62 84.0 ' July...................... 115 71 87.8 Evaporation June July Concrete tank, inches............ 11.7 10.72 Iron tank, inches.............. 14.8 13.07 Rainfall, inches................ None 0.77 Cloudy days................... None 10.00 Aside from several springs about 10 miles from the property, the nearest known water in quantity at the time these experiments were made was the Gila river at Gila Bend, 45 miles distant. Part of the developinent of the property of course included drilling for water in the valley, which was in progress at the conclusion of my experiments. The ore deposit itself is unusual. It consists of of intrusive plug of monzonite or granite porphyry. Chalcopyrite, bornite, and magnetite are finely disseminated throughout the magma in sufficient quantities to make the greater part of the mass commercial ore to a certain depth.

Jan 1, 1915

By Juliana Cecília Costa Ribeiro Vieira

Na Mina de Serra Azul da ArcelorMittal em Itatiaiuçu Minas Gerais há toda uma sistemática de controle dos processos produtivos desde a lavra, planta de concentração, estocagem, transporte ao pátio de carregamento, avaliação das características de qualidade no embarque em composições ferroviárias e assistência ao cliente no embarque do produto para a destinação final. As principais análises químicas (%) realizadas são: Fe, SiO2, Al2O3, P, Mn,TiO2, CaO, MgO e Perda Por Calcinação(PPC). Essas análises são padronizadas por normas técnicas ABNT ISO tanto para atender ao mercado interno quanto ao mercado externo. Não há como garantir a qualidade das análises se não houver uma certificação da qualidade dos padrões de referência de forma a calibrar equipamentos de análise, verificar e controlar metodologias e treinar e avaliar os analistas. A produção na Mina de Serra Azul é um processo dinâmico em constante evolução e requer uma gama grande de padrões de referência com características próprias que o mercado de material de referência não tem condições de suprir. A ArcelorMittal partiu então para desenvolver uma metodologia simplificada, mas eficiente com base em critérios estatísticos consagrados para produzir seus próprios materiais de referência secundários (ou internos) de forma a atender a sua própria demanda deste tipo de material.l

Oct 30, 2017

By William H. Lesser

Never before have mine managers in the anthracite region of Pennsylvania been so seriously concerned about the rising cost of pumping mine water. Many of them know that future pumping charges may affect their operating profits adversely to an extent that will make it necessary to abandon some mines. Increased pumping charges in the anthracite industry are currently comparable in importance with higher mining costs; in fact, profitable operation of some mines depends not only upon the cost of mining coal but also upon whether they can be kept free from water at reasonable cost. Pumping charges are relatively low during the early development of a mine, but they increase rapidly as development progresses. Numerous crop falls, strippings, and. abandoned adjacent properties contribute unfavorably to the volume of water produced during mining. The foregoing conditions and the existence of large underground pools below existing mining levels present water problems of such magnitude and cost that some mine owners cannot continue to operate profitably.

Jan 1, 1950

By James K. Gowans

The Red Dog Operation is located in northwestern Alaska at Latitude 68°, 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The orebody was acquired by the NANA Regional Corporation, (an Alaska Native Corporation established by the Alaska Native Claims Settlement Act of 1971), in 1980 in their land selection. In 1982 Cominco American and the NANA Corporation signed a development agreement and Cominco Alaska Inc., a wholly owned subsidiary of Cominco American, was formed to manage the Red Dog Project. An extensive exploration program in 1980 -1982 outlined a mineral inventory of 85 million tons, at a grade of 5.2% Pb, 17.1 % Zn, and 2.4 oz/ton Ag, which makes the Red Dog the second largest deposit ever discovered. Broken Hill, in Australia, is the only zinc orebody which was originally larger than Red Dog. The design of the facilities is to process 2.1 million tons of ore annually, which will produce 560,000 tons of zinc concentrate, 100,000 tons of lead concentrate and 50,000 tons of bulk lead/zinc concentrate.

Jan 1, 1991

By L. A. Nemchinova, M. A. Arustamian

"For a long time tailings piles of mining and smelting complexes have met the eye being a prospecting feedstock source for many industries. Nowadays, 6.5 million tons of copper and cooper-zinc processing tailings are stockpiled in the Urals annually, as there is no technology of its processing to provide a full and complex metal extraction within mining and processing operations. In spite of large volumes of mining wastes, not more than 20% of annual overburden, approx. 10% of processing wastes, approx. 40% slags (1) are involved into processing.Based on today’s complex of economic, environmental and social challenges of ore processing, waste processing technology using existing capacities is a burning issue. Mining wastes characteristics (including fine dissemination, variability of physical and chemical properties of mineral surfaces under impact of oxidizing, leaching, etc.) predetermine challenges arising out of its involving into processing and justify high capital intensity of new construction or reconstruction projects followed by replacement of existing processing lines with new ones.In this paper, the authors propose flotation technology for mature tailings of copper, copper-zinc and polymetallic ore processing. The technology developed provides for upgrade of existing process flowsheet diagrams at minimum costs to produce additional saleable products including low-grade copper concentrate, saleable zinc concentrate and gold concentrate thus facilitates sustainable use of depleting minerals and operational efficiency due to cost-efficient processing of already mined materials, being in fact, final semi-products located near existing operations. This is particularly important for operations with standby capacities and not engaged workforce."

Jan 1, 2018

By E. S. Shedd

The Bureau of Mines investigated electrowinning and tapping lanthanum metal from lanthanum oxide in a fluoride bath. The electrolyte was composed of LaF3, BaF2, and LiF. Metal containing 0.2 percent impurities was produced at a rate of over 2 pounds per hour. Principal impurities were carbon, aluminum, and silicon. Low-carbon metal was produced by continually discharging the carbon oxide gases and maintaining 0.1-atmosphere pressure. Anode reactions and cell design were found to be important factors in cell operation. Both frozen electrolyte skulls and tungsten metal crucibles proved satisfactory for collecting the metal and did not react with the molten lanthanum.

Jan 1, 1966

By Partha Patra

Numerous proteins of varying properties are available in extracellular bacterial proteins (EBP) isolated from Paenibacillus polymyxa. EBP was fractionated through ammonium sulfate precipitation in a controlled fashion and characterized through SDS-PAGE technique. Different groups of proteins, (Group A~D) exhibited varying degrees of surface affinity to minerals such as quartz, pyrite, chalcopyrite, galena and sphalerite. Interaction with mineral specific bioproteins rendered pyrite and chalcopyrite hydrophilic while surface of quartz, galena and sphalerite turned more hydro-phobic. Specific groups of proteins could thus be used for selective separation of galena, sphalerite and quartz from pyrite and chalcopyrite (as a mixed sulfide) through microbially-induced flotation or selective flocculation.

Jan 1, 2014

By Hung-Kei H. Lam

Rubidium and cesium were discovered by Bunsen and Kirchhoff about 100 years ago. These two elements are by no means as abundant as sodium or potassium. Their occurrence in minerals is widespread, but usually as minor constituents. There is no known specific ore containing rubidium, but rubidium is found replacing the. other alkali metals in .some minerals.. Perhaps the highest concentration of rubidium found in one mineral is in lepidolite, KLi(OH,F)2A12Si3010, which contains from 0 to 3.5%*Rb20. 0n the average, lepidolite contains about 0.5% Rb20. Other sources of rubidium are carnallite, KMgCl3?6H20; pollucite, H20.2Cs20.2AI203.9SiO2; rhodizite, R20.2A1203-3B203; biotite, H2K(Mg,Fe)3A1(Si04)3; sea water, rivers, marine and fresh water organisms, soils, and plants. Cesium, even though it is the least abundant. of the stable alkalies, has a specific ore. Pollucites a hydrous cesium aluminum silicate, may con¬tain as high as 42.5% Cs20, although again, the average Cs20 content is about 25% among the handful of known deposits. Other cesium-containing minerals are lepidolite and carnallite. Rubidium and cesium are very much like potassium in chemical properties, consequently, they are hard to separate. Because of the difficulty in obtaining pure cesium and rubidium compounds coupled with the scarcity-of supply, prices were high and the two elements enjoyed little industrial use. Just before the Second World War, the world. supply of rubidium and cesium, from Germany, was a matter of tens of kilograms per year and prices were about

Jan 1, 1959

By Roger K. M. Bellows

The last coal-fired power plant to be built in Canada came into operation in 1994. Since then, Canada?s electricity requirements have grown substantially but no new coal-burning plants have been built. This country has abundant resources of coal from coast to coast, but in recent years, this has not affected our choice of fuel. In many other countries this is not the case, and the use of coal is growing rapidly. Although this presentation covers the topic from an Alberta perspective, some of the conclusions can be extrapolated to the rest of the country, and perhaps even to other countries. The coal found in the Alberta plains is particularly attractive because of its low cost and low sulphur content. Yet coal is no longer the fuel of choice, and a long-standing provincial government policy to favour coal for electricity generation has been ignored for more than a decade. Considering the lack of good alternatives, it seems obvious that we should look to coal as our primary energy source in the generation of electricity and for other industrial applications. This paper discusses some of the reasons that coal has fallen out of favour, particularly with respect to electricity generation. The significance of the deregulation of the electricity industry will not be ignored. In addition, the author will offer his opinion on the question of what it will take in order for coal to once again become the favoured fuel.

May 1, 2001

By E. Lovera

ABSTRACT: The current study analyzes the feasibility of an odd operation: to obtain, using a properly tailored drilling and blasting scheme, blocks suitable for the production of dimension stone from tunnel driving. Clearly, a compromise must be found between the rate of progression and the achievement of workable blocks. As a case study, a civil work under consideration in northern Italy was examined. The work was planned to cross a conglomerate that has traditionally been locally exploited for the production of highly prized paving and lining stones with excellent strength and aesthetic features. Natural exposures and mined-out quarries were available for tests. The relevant rock data are given, blast designs are shown (within the limitations of contour accuracy), and the test program is described.

Jan 1, 2011

By Mark Kramer

This paper is limited to treatment of bottom and fly ash waste resulting from WTE and RTE Cogeneration plants, commonly known as trash burners. The body of the paper defines waste generation and conventional treatment schemes. This paper does not identify a best treatment, however, it does offer a general perspective of the treatments to lead the reader to further investigation. Advantages and disadvantages of the ash treatments Is discussed in each treatment section.

Jan 1, 1996

By Gerard McAlinden, Daniel Frost, Patrick McAlinden, James McAlinden

In an effort to recover Polychlorinated biphenyls (PCB’s) that had leached into bedrock below the Hudson River in Upstate New York, a shaft and tunnel complex was designed that would allow installation of inclined and vertical wells into the zones of contamination to recover PCB’s by gravity. A joint venture of Merco Inc., of Lebanon, NJ, and Obayashi Corporation, of San Francisco, CA, was awarded the contract for constructing the first Tunnel Drain Collection System in the world. Conventional drill and blast techniques were the most economical method to construct the project but due to the presence of PCB’s and community concerns, innovative drill and blast practices were needed.

Jan 1, 2010

By Nur Hossain

Analysis of Linear Elastic Fracture Mechanics (LEFM) parameters via the Virtual Crack Closure Technique (VCCT) has been obtained for SENT specimens of AM6OB magnesium alloy. It is found that the ratio of initial crack length to initial monotonic plastic zone size is one of the critical factors in establishing the limit of using LEFM concepts. If this ratio is below a certain limit (i.e. when crack lengths are small in comparison to the plastic zone size), loss of similitude stress intensity factor range would occur. This ratio, therefore describes the limit below which the use of LEFM would no longer be admissible. In this study, the above limit was established for AM6OB magnesium alloy. In addition, fatigue crack propagation tests were conducted to ascertain the fatigue response of the alloy and determination of the coefficients of Paris model.

Jan 1, 2010

By S. Xu

Magnesium alloy AM50 is of interest to automotive cradle application because of it excellent castability and good ductility. In this work, microstructure and mechanical properties of both low pressure die cast (LPDC) and high pressure die cast (HPDC) AM50 test bars are characterized. Microstructure was examined using optical microscope, scanning electron microscope (SEM) and transmission electron microscope (TEM). Phase identifications were performed using energy dispersive x-ray spectrometer (EDS) and TEM diffraction. It has been found that LPDC produces much coarser microstructure than HPDC. At the same time, the HPDC samples are more heterogeneous in microstructure and composition close to grain boundaries. Particles with various dimensions and morphologies of two different intermetallic phases, Mg17A112 and A18Mn5, were found in all the samples. Mechanical tests were performed under conditions similar to those related to an engine cradle application. LPDC samples show lower strength but better creep resistance than HPDC mainly due to the difference in grain sizes and grain boundary microstructure between LPDC and HPDC. Creep curves are well described by the empirical Andrade equation. Tensile-compressive yield and creep asymmetries were found in AM50, i.e. better deformation resistance in tension than in compression. The average yield asymmetry ratio for all the samples is 0.87. Microstructural examinations on the samples tested in tension, compression and creep showed that the deformation mechanisms in AM50 were slip plus twining at temperatures up to 125°C. The examinations indicate the important role of twining in the asymmetry phenomenon. The creep results indicate that dynamic precipitation of the Mg17A112 phase during testing is not the mechanism directly responsible for the creep asymmetry in AM50.

Jan 1, 2004

By Werner Wenzel

Whisker growth during the reduction of iron ores The phenomenon of whisker growth can be observed in a number of solid-state crystallisation reactions, which, apparently, appear in6 the first instance as though they are two independent processes. From such reactions, one can find the whisker type of crystallisation on solid bodies. These examples show, that the whisker growth is neither due to certain crystal forms with predetermined temperature and pressureranges, nor to parameters, which, ad hoc, are necessary for the crystallisation. In all cases the whisker formation seems to depend on nucleation and the availability of crystallizing material in direct environment of such a nucleus, under given parameters of a system. One can generally state, that the research of whisker growth with the aim of establishing proper physical laws, to determine the foundamentals of whisker formation and whisker growth, is at present under active study. We can conclude that, although a great number of hypothesis have been proposed; no concluding theory has yet been arrived at. In the institute for ferrous metallurgy of the technical university of Aachen, research works are undertaken to find an explination to various metallurgical phenomena through help of whisker growth which was observed under varying conditions of iron ore reduction. This was possible by using refined microscopic techniques through which the whisker growth on solid oxyde substrates is detected. This refined technique combines the latest methods of surface examination with the help of stereo-scan-electron-microscope and proper and carefull preparation of surface to be stereo-scanned.

Jan 1, 1971