Search Documents

By C. P. Bowie

For years many oil producers have believed that often low-pressure oil- and gas-bearing strata have been over coked in fields where the rotary system of drilling has been used. Collom3/ gave as a reason for this condition that because the mud fluid was thick, the oil or gas stratum was plastered and sealed as the tools passed through it and no oil showed at the surface. Although this observation was made 15 years ago, it may often still be true notwithstanding modern developments in coring and electrical logging. Operators have believed, also, that mud fluid does not solidify behind the casing. Lewis and McMurray4/ stated: "All the evidence obtainable from practical experience points to the fact that the mud fluid properly mixed and employed does not solidify behind the casing, even in deer wells and after long periods."

Jan 1, 1937

By J. S. Kennedy, M. M. Fine

"INTRODUCTION Barite is one of the major industrial minerals whose production has increased considerably in the last 10 years. In 1935 domestic production of barite was 218,075 tons and. had increased by 1944 to 515,136 tons. 3/ Most of the primary uses for barite and barite products were developed before 1935, so the increase in barite production reflects the growth of industry in general rather than any recent developments in barite technology.The principal uses for ground and crushed barrite are as a weighting agent in heavy drilling fluids, as a filler in rubber and other materials, as a pigment and extender in paints, and as a flux in glass melt. In addition, a considerable' quantity of barite serves as the raw material for the manufacture of lithopone and barium chemicals.Specifications for barrite vary widely and depend primarily on the use to which the material is put. The primary requisites for barite used in heavy drilling muds -are that it have a minimum specific gravity of 4.2 and be very,low in soluble salts. A minimun barium sulfate content of 92 percent may be specified; but this is less important than the gravity. 4/ In addition before consumption the material must be ground to '92 percent minus 325-mesh. 5/ Lithopone and chemical manufacturers require a minimum of 94 Percent barium sulfate, a maximum of 1.0 percent iron oxide, and not more than a trace of fluorine. 6/ Barite used as fillers in light-colored products should be of fairly high grade, but the filler used in dark products may be considerably lower grade.Glass barite should contain a minimum of 96 percent barium sulfate, not more than 3 percent moisture, a maxium of 0.2 to 0.4 percent iron oxide, and not more than a trace of titanium oxide. Particle size is a matter of some importance in glass barite, also. 7/"

May 1, 1948

By John L. Dahle

This report documents the research efforts that were undertaken to design, install and test noise abatement devices for use on off-highway haul trucks operating in surface mines. The objective of the program was to reduce the environmental noise from haul trucks. The noise reduction devices that were developed utilized existing technology and were tested on a 50-ton haul truck. The efforts emphasized the reduction of noise emitted from the engine compartment which included the use of side shields, sound absorbing material, improved radiator shroud design, and a modulating clutch fan. Noise tests were conducted using modified SAE test procedures for measuring sound levels around a stationary and moving machine, and inside of the operators compartment. Test results showed a maximum of 4 dB(A) reduction measured 16 feet from the truck. Interior cab noise was reduced 6 dB(A) with the windows and vents closed.

Jan 1, 1983

By Michael R. Kennedy

This report describes the demonstration of longwall mining in a seam dipping 27 to 34'. Equipment was selected on the basis of capability, compatibility, and co t. Snowmass, Bureau of Mines, consultants and manufacturers were involved in the selection process. The equipment arrived in early 1981, prior to completion of development for the first panel; therefore, the equipment was operated on the surface for training. The surface training paid off with a fast, efficient installation and start-up of the face. The longwall equipment operated very well on the steep pitch with an average equipment downtime of 21.9[9]. Coal handling outby the face was a problem which caused an additional downtime of 19.5%. Development for the panels proved to be the major problem in the economics of longwall mining on a steeply dipping seam. During the first 9 months of operation the longwall averaged 71.9 TPMS and development averaged 0.6 TPMS for an overall average of 14.1 TPMS. Had mining continued, timing of development would have been another major problem. Monitoring of subsidence, pillar stability and shield loading was done in connection with mining, but little useful information was gained from the monitoring.

Jan 1, 1987

By D. H. Platt

Data obtained from on-the-site observations have been compiled to describe the equipment and installation methods used for satisfactory suspension roof support in a large-diameter tunnel. Experimental roof bolting was undertaken from June 1950 until May 8, 1951, in the East Delaware tunnel, which is part of the Delaware aqueduct in Delaware and Sullivan Counties, N. Y. Revised suspension-roof-support plans and specifications were prepared during the spring of 1951 by the City of New York Board of Water Supply; these were approved by the State of New York Department of Labor April 13, 1951, and adopted by the City of New York Board of Water Supply on May 8, 1951.

Jan 1, 1952

By J. Peterson

A review of blast designs and improved blasting practices at the Ekati??Diamond Mine is presented along with the results of three blast-monitoring experiments. Blast monitoring was undertaken to investigate blast damage mechanisms in the mine's well jointed rock mass. Rock mass damage caused by production, pre-shear and wall control blasts was measured. Ekati??uses 270mm holes for production blasting, and 165mm holes loaded with a decoupled charge for pre-shearing. The production blasts are loaded with bulk emulsion / ANFO blends. The mine plan involves using 30m double benches. A 30m high pre-shear is drilled and blasted prior to the production blasting that is done with sequential 15m benches. This paper summarizes the monitoring equipment and data gathered to date.

May 1, 2001

By E. W. Felegy

Since 1920, the Bureau of Mines and, other agencies have conducted numerous investigations of methods of communication for use in mines in times of disaster or emergency. The results of these investigations have been reported in various publications (3, 4; 5, 6, 8, 9, 10, 11, 12, 13, 14, 15, 16). In November 1944, the Bureau of Mines resumed the study of emergency underground communications. Until March 1946, the program was directed toward reexamining methods of underground communication that indicated possibilities of success. Since April 1946, the principal interest of this investigation has been in methods of application of radio to communication in mines, low-frequency radio seeming to offer the most promise as a successful method of emergency mine communication. Results achieved in reexamining other methods and in the investigation or the application of low-frequency radio between November 1944 and September 1946 were reported previously in a publication entitled "Some Studies on Emergency Mine Communications".

Jan 1, 1948

By Ray Mason

Marathon PGM Corporation?s PGM-Cu Project in Northwestern Ontario (Figure 1.0) serves as a case study to describe the process involved in advancing a deposit from grass roots exploration to the completion of several feasibility studies and the parallel commencement of environmental permitting. Through the following examination of historical exploration activities, it is clear that these activities are directly related to economic stimulus, mostly measured by downturns in the mineral industry. Other factors that influence the success of exploration advancing to feasibility and new mine development includes the ownership of the mineral claims, which also changes under these economic influences and the crucial role of interactions between the Company, the Crown and First Nations. The Marathon PGM-Cu deposit is hosted within the Eastern Gabbro Series of the Proterozoic Coldwell Complex, which intrudes and bisects the much older Archean Schreiber-Hemlo Greenstone Belt. The sub-circular complex has a diameter of 25 km and a surface area of 580 km2 and is the largest alkaline intrusive complex in North America (Walker et al., 1993). Mineralization at the Marathon PGM-Cu deposit is part of a very large magmatic system that consists of at least three cross-cutting intrusive olivine gabbro units that comprise the Eastern Gabbro Series of the Coldwell Complex (Figure 3.2.4-3). In order of intrusion, the three gabbroic units consist of (1) Layered Gabbro Series, (2) Layered Magnetite Olivine Cumulate (LMOC) and (3) Two Duck Lake (TDL) Gabbro. The relative size and abundance of the gabbroic units decrease in the order Layered Gabbro Series>TDL Gabbro>>LMOC. Late quartz syenite and augite syenite dikes cut all of the gabbros but form a minor component of the intrusive assemblage.

May 1, 2010

By F. L. Wideman

This report describes the sinking of No. 3 shaft at the Westvaco mine. It is one of a series of publications of the Bureau of Mines on mining methods and practices in the United States. The Westvaco mine is in Sweetwater County, Wyo., approximately 23 miles northwest of the town of Green River (fig. I), There are no permanent habitations in the vicinity of the mine, and employees live in Green River or Rock Springs, Wyo., 14 miles us t of Green River. The mine plant is on a windswept, treeless plain, from which low buttes and flat-topped ridges rise. The altitude at the collar of No. 3 shaft is 6,351 feet. The climate is arid, with temperatures as low as 40° below zero in the winter. Blacks Fork, a tributary of the Green River and a perennial stream, flows near the mine.

Jan 1, 1959

By H. C. Horwood

INTRODUCTION THE Argosy Gold Mines, Limited, which joined the ranks of active Ontario gold producers during the summer of 1936, holds a group of 21 claims on Casummit lake, in the Patricia portion, district of Kenora, northwestern Ontario. The Company is developing and mining goldbearing quartz veins that occur in a series of greywackes and slates of probable Keewatin age. The writer made a geological examination of the property and the surrounding area for the Ontario Department of Mines during the early part of the field season of 1936. This paper is a report on the general geology, structure, and ore deposits at the mine and is based almost entirely on data compiled during the examination. HISTORY Mineralization was first discovered on the property in May, 1929, by A. F. Hewitt, who, with J. A. Borthwick, decided that the country had prospecting possibilities and commenced work in April. Mr. Hewitt staked, and with his partner, J. Ziyone, still holds the group of claims lying immediately east of the present Argosy holdings. Mr. Borthwick staked six claims, K.R.L. 9,681 to 9,686, inclusive, adjoining Hewitt's on the west and later added claims K.R.L. 9,733 to 9,740, inclusive, to his holdings. F. Fiskness, who was also prospecting in the region, discoveted No. 1 vein on Borthwick's claims, and with his two partners, L. Parth and H. Jones, staked claims K.R.L. 9,758 to 9,763, inclusive, to the northwest of Borthwick's and Hewitt's ground. In July, 1929, the Casey Mountain Operating Syndicate, which held ground to the northwest, secured an option on Borthwick's claims. The Fiskness-Parth-Jones property was added in January, 1930, to protect the west dip of the veins. During the winter of 1930-31, the veins were explored by diamond drilling, No. 2 for a length ?of 900 feet and a vertical depth of from 51 to. 375 feet? and No. 3 .t~ a slope depth of 175 feet. I~ August, 1.931, after the msrallat10n of a miming plant, the Casey Summit Gold Mmes, limited, was incorporated to take over the property from the Syndicate. The Maple leaf Mines optioned a controlling interest in the stock in August, 1933, and on September 17th, 1934, brought a 50-ton amalgamation mill into production. From early in October to December 27th, 1934, when the mill was closed down, 4,094 tons of ore were treated to yield 887.89 ounces of gold and 87 .26 ounces of silver( ! ).

Jan 1, 1937

By L. C. Graton, Joseph Murdoch

I. Introduction......................... 26 1. The Relations of Scale in Geologic Work........ 26 2. General Characteristics of Copper Sulphide Ores..... 29 3. Scope of Present Study................. 31 11. Description of the Important Minerals............ 36 1. Pyrite....................... 36 2. Pyrrhotite....................... 41 3. Chalcopyrite...................... 41 4. Bornite........................ 40 5. Covellite....................... 50 6. Chalcocite....................... 52 7. Enargite...................... 59 8. Tetrahedrite and Tennantite.............. 61 III. Conclusions.......................... 62 I. Introduction. The Relations of Scale in Geologic Work. Many features of human accomplishment rest upon the possibility of representing natural objects on a scale of different magnitude from the actual one. Most drawings, for example, are of very different scale from that of the object depicted, and indeed are useful mainly 011 this account. More important than the question of mere convenience, however, is that of meeting the physical limitations of vision.' Thus, a mural

Jan 1, 1914

By G. G. Richards

"The slag fuming process has operated for close to 70 years to recover zinc from lead blast furnace slag. The process is normally carried out through the batch treatment of slag by submerged injection of coal and air. Within the bath the coal acts as both a reductant, to reduce Zno to zinc vapour, and a fuel, to maintain bath temperature during the endothermic reduction process. The partition of coal between the slag, combustion and bypass is dependent on factors such as bath depth and injection pressure. The option of continuous fuming has been pursued at the D. Blagoev smelter in Bulgaria using heavy fuel oil as reductant/fuel. There has, however, been little attempt at commercial continuous fuming with coal. This paper presents an analysis of a coal-based continuous slag fuming furnace. The data on the Plovdiv fumer is used as a reference point. Critical design criteria for continuous fuming include the slag feed rate, degree of coal combustion and furnace size. Mathematical modelling analysis suggests that continuous fuming with coal can achieve respectable zinc/coal ratios.IntroductionThe slag fuming process was developed in the early part of this century to recover zinc from non-ferrous smelting slags [1-3]. The majority of installed furnaces were put in place to fume zinc from lead blast furnace slag on a batch basis. In most cases coal is used to effect reduction of zinc oxide, but one furnace uses natural gas [4] and, in a curious twist, a continuous fumer was developed based on fuel oil [5].Given the general nature of blast furnace lead smelting, it is not surprising that slag fuming has remained a batch process, in spite of the advantages that could be gained by moving to continuous fuming. Blast furnaces are usually operated as relatively independent units, and tapping has traditionally been done into ladles. The presence of a crane aisle makes direct coupling of the blast furnace to a slag fumer difficult, especially in a retrofit situation. Furthermore, steady-state blast furnace operation is not easy to achieve. The size of these furnaces and the nature of their feed make it difficult to guarantee constant operation."

Jan 1, 1996

By Matteo Tomba

Today’s steel market is characterised by high competitiveness and tight profit margins; therefore, the operational costs of rolling mills must be as low as possible, while ensuring a final product of the highest quality standards. PERT SRL is an engineering company with a long-term experience in the international steel market, specialised in the design and supply of highly innovative and bespoke solutions for siderurgical and environmental plants. Because of its strong commitment to deliver excellent products and services, and its ability to innovate and adapt to the fastchanging market requirements, PERT has studied a new generation of BI-SUPPORT rolling stands, designed to be used in rolling mill plants for the production of rebars, rounds and sections in special quality bars (SBQ) steel grade, wire rod, light and medium section, suitable also for special steel plants. This paper will provide a deep insight into the key technical and economic features that have revolutionised the rolling technology for long products, such as the absence of spindles and piping on board, the considerably reduced number of spare parts required, a ring gap regulation system, and the compact dimensions, which lead to significant savings in investments and production costs; at the same time, the BI-SUPPORT stands guarantee excellent standards to the final product, an increase in plant productivity and a general improvement in the plant management.

Aug 16, 2017

In 1985 BMR assessed Australia's economic demonstrated resources of mineral sands as follows: rutile 8.0 Mt, ilmenite 41.4 Mt, zircon 11.5 Mt, and monazite 229 000 tonnes. These resources are located along the east coast of Australia, in the southwest corner of Western Australia, and in the Eneabba region, north of Perth, WA. However, over 40% of Australia's rutile and zircon resources, particularly those on the east coast, are presently not available for mining because of environmental considerations. As well, east coast ilmenite has been considered unsuitable for use by sulphate route pigment producers because of its relatively high chrome content. World demonstrated resources of rutile and zircon are estimated by BMR as 29 Mt and 38 Mt respectively. Demonstrated resources of ilmenite amount to about 1 billion tonnes. These occur predominantly in hard rock deposits in Norway, Canada, USSR and China, as well as alluvial deposits in Australia, South Africa and India. Quantitative data for world monazite resources is sparse. However, world production of rare earth oxides is now mainly from bastnaesite, a hard rock resource. Australia is presently the world's principal producer of rutile and zircon, and also provides a major share of the world's ilmenite. With the expected increase in Australia's rate of output of these commodities, combined with restrictions on mining along parts of the east coast, its position could diminish substantially over the next 25 years.

Jan 1, 1986

By Lucas Tedesco Bolzan

Blindagens contra armas de fogo são de grande importância para proteção do homem, no contexto atual de violência urbana e conflitos armados. Destacam-se os sistemas de blindagem multicamada (SBMs), constituídos por materiais diferentes, pelo seu bom desempenho e menor peso. Um SBM típico é constituído de uma camada cerâmica frontal, uma segunda camada de compósito e uma camada posterior de metal dúctil. Apesar de serem tipicamente fabricados em materiais sintéticos, uma alternativa é a utilização de compósitos reforçados com fibras naturais como segunda camada. Este trabalho tem como objetivo verificar a eficiência de SBMs que utilizam compósitos de poliéster com 30%vol. de fibras ou tecido de sisal. Foram realizados ensaios balísticos com munição 7,62 mm, e verificou-se que os SBMs com fibras e tecido de sisal se enquadram no critério da norma internacional (NIJ 0101.06), de resistir ao impacto balístico e imprimir deformação menor que 44 mm no material de referência (plastilina), além de manterem sua integridade após o impacto.

Aug 17, 2017

By G. L. Oldright, Virgil Miller

"This paper is the ninth 4 of a series on smelting in the lead blast furnace, and the fourth on modifications brought about by the introduction of richer charges.ACKNOWLEDGMENTSThe authors wish to express their appreciation to Stanley A. Easton, Frank M. Smith, and A. F. Beasley, and to their staff for the whole—hearted cooperation that made it possible to obtain the data in this publication at the Bunker Hill smelter, Kellogg, Idaho.INTRODUCTIONIn tie account written of the conditions obtaining at the tuyere zone in the blast furnaces at Tooele (R. I. 2965) the authors gave references to articles covering (1) the effect of temperature on the equilibrium 2C0 - CO2 + C, (2) experimental work that has been done on learning the gases existing at various elevations in columns of burning coke, (3) extension of this work to the tuyere zone of an iron blast furnace, and (4) the paper itself gave similar analyses of the gaseous oxides of carbon at the tuyere zone of a lead blast furnace and showed the temperatures obtaining there. There were also references in the above paper to the literature on (5) how the lead compounds likely to be present might be ex¬pected to react. A careful study of the original articles selected as references will give a good background for the present work.The following very brief recapitulation may be convenient before considering the tuyere zone in the blast furnaces at Kellogg. The ""producer gas reaction"" (1) of course goes to the left at increasingly higher rates of speed with increase of temperature. When air is blown upward through a grate and a column of hot fine coke alone, oxygen as such penetrates from some 2 to 3 inches only, under the conditions obtaining as to the amount of surface exposed per unit volume of air. When air is blown at about 20 pounds pressure through the tuyeres in the side of an iron blast furnace into a column of coarse coke (plus furnace charge) it may penetrate for 30 inches before the oxygen is entirely used, burning first largely to CO2. Within wide limits, the rate of feeding air into the furnace has practically little effect on the composition of the gases obtaining in the fuel bed of fine coke, this being true particularly of the gases leaving the bed. Some 10.5 inches above the grate the gases contained 22 per cent of CO by volume, and a little further up the CO2 had practically disappeared. This gave the familiar three zones in both the iron blast furnace and the gas producer; in order of entry of the air, in the first the oxygen burned largely to CO2, in the second the CO2 was reduced to CO, and the third the CO2 was practically absent. In the furnaces at Tooele, conditions were somewhat erratic but the first two zones were present, there being, however, no zone in which CO2 and 02 were both entirely absent."

Apr 1, 1931

By John R. Bradley

The object of this paper is to survey and analyze the bearing of economic nationalism, competitive sources of energy, and technologic developments on international trade in coal with especial reference to the competitive position of the leading coal-exporting countries in the Italian market, the largest in the Mediterranean region, and the Brazilian market, the second largest in Latin America. The political, economic, and financial disturbances caused mainly by the World War have resulted in an amazing situation. Especially since 1930 have conditions been complicated.

Jan 1, 1936

By Vishnu S. Gupta

A modular computer program APEX (AMAX Process Evaluation Executive), has been developed at AMAX Extractive R&D, Golden, Colorado to facilitate rapid simulation of steady state material and energy balances of existing and/or proposed metallurgical process flowsheets. Currently, APEX is being used for the design, analysis, and evaluation of several of AMAX?s Nickel, Molybdenumand Tungsten processes. A unique feature of APEX is that it allows specifications of flow rates and compositions for different solid size fractions in addition to aqueous organic and gaseous phases. Thus, a metallurgical process which may involve crushing, grinding, flotation, leaching, washing, solvent extraction, precitation and refining operations can be simulated in a single computer run using APEX. APEX requires two input data files. The first is a process data file which includes physical and thermodynamic properties of the various chemical components of interest. This data file is unique to the process under study and does not require changes for alterations in the process flowsheet. The second data file is specific to a simulation case and includes descriptions of the flowsheet, various feed streams and the process equipment's operating conditions. In addition to temperature, pressure and percent solids, calculated information for each stream includes weight and volumetric flow rates, chemical compositions, specific gravities and enthalpies of solid, liquid and gas phases. For each process equipment in the flowsheet, APEX prints its operating conditions and detailed information about the streams that enter and leave the unit. Models of several general unit operations are preprogrammed in APEX. Also, the modular design of APEX permits quick and easy additions of simulation models which are specific to new and/or unique process operations. To study process stability and optimization, APEX permits several cases of a flow-sheet to be run together. Three simulations of the Moa Bay Nickel process have been excluded to illustrate the ease and flexibility of using the APEX system.

Jan 1, 1980

By John H. Soule

The Torpedo Copper mine in the Organ Mining District, Dona Ana County, N. Mex., was discovered In 1899. Production was begun immediately and continued until 1907. Since 1907 very little ore has been produced, although Many individuals and companies have been interested in the property at one time or another. Approximately 6,621 feet of diamond-core had been completed on the property before 1949. The results from some of this drilling were unsatisfactory because of the poor core recovery. In addition to its investigation of the Torpedo ore deposits, attention was given by the Bureau of Mines to obtaining better core recovery through the use of special equipment and techniques. This project was begun October 3, 1949, and was completed April 30, 1950. Four diamond-drill holes totaling 2,140.5 feet, which includes 18.2 feet of overlap in a deflected hole, were drilled. All drilling was done with a Government-owned hydraulic-feed drill with some special rods and core barrels, in addition to the usual equipment. The over-all core recovery was 89.5 percent. Omitting the drilling in overburden where little or no core was desired, the recovery was 94.6 percent. Core recovery in the ore zones averaged 95.2 percent. This paper describes the location, the general features of the area, the geology, the Bureau of Mines procedures, and the results attained by these procedures.

Jan 1, 1952

By Jesus Frisancho Cabrera

El aumento de precios por la demanda de acero en China, consolida a dicho país en un importador neto de molibdeno desde 2010. En ese contexto, el presente texto señala la influencia del molibdeno en la exploración del pórfido de cobre -en tanto los bajos niveles de las exportaciones de crudo de China continúan obligando a los productores de acero de Corea y Japón de molibdeno utlizarlo como fuente de Occidente.

Sep 12, 2011