Search Documents

By Mario H. Castro-Cedeno

"A design for a handheld MEMS chemical detector is proposed. The detector will be used to detect trace amounts of chemicals in air. It can detect drugs, toxic chemicals and/or explosives. The proposed detector will use ion mobility spectrometry (IMS), a technique that is well known for accuracy and has been used in the past in suitcase sized chemical detectors. The separation and detection of the chemicals occurs in the drift channel and the process was modeled using the finite element method and CoventorWare modeling software. A manufacturing process sequence for the drift channel is proposed and was demonstrated.IntroductionThe goal of this effort is to design, mode~ and prototype a MEMS chip that will be the key component in an ion mobility spectrometer (IMS). This technique uses and asymmetric potential to separate the various ion species in a stream of incoming air [1-4]. One advantage of IMS is its ability to separate chemical species from air at atmospheric pressure and temperature. This is a requirement for a simple to use handheld drug or chemical detector. IMS can be used to detect drugs, toxic chemicals and explosives and it is well known for accuracy in detecting very small amounts of chemicals. This chemical detection technique has been used in the past, but not in handheld detectors.One variant of IMS is the high-field asymmetric waveform ion mobility spectrometry or FAIMS [3]. The FAIMS process, shown in Figure l, works as follows: a gas sample is admitted into the instrument where gas molecules are ionized, typically by a weak radioactive isotope source, ultraviolet light source; and more recently through field emission. The ions move along the length of a channel while they are separated in the transverse direction by an asymmetric electrical potential. The potential, in the form of an asymmetric waveform, causes relative motion between the various chemical species. The species that hit the charged top and bottom plates are neutralized and only those ions that move along the center are detectable as charged chemical ions at the end of the channel."

Jan 1, 2004

By S. S. Lu

In sodium oleate and salicylhydroxamic acid systems, sequence of floatability of three sulfate minerals is: barite>celestite>gypsum, in lauryl amine system is: gypsum>celestite>barite. XPS and infrared spectrum analysis are used to find that it is chemical reaction between sodium oleate and three minerals, physical adsorption on the surface of minerals for lauryl amine, and it is chelating reaction between salicylhydroxamic acid and three minerals possibly. Theoretical calculation on chemical bonds in crystal structures of three minerals is carried out, finding that breaking degree of Mn+?O2- in crystal structures of three sulfate minerals is closed related with floatability.

Jan 1, 2014

By F. A. Forward

"NINETEEN sixty-six is a year of unusual significance in our Institute and in our country. It marks two-thirds of a century of service by the Institute to the people of the mineral industry and two-thirds of the century that Sir Wilfred Laurier said ""belongs to Canada."" As we meet here today within the historic walls of Canada's oldest city, a city that looks back on three hundred and fifty years of progress, I am reminded that it is almost a third of a century ago -in April, 1934 -that here in Quebec I first attended an Annual General Meeting of the Institute. It occurred to me that it might be appropriate to examine briefly the change that the middle third of this century has brought in the affairs of the mineral industry and, with some trepidation, to consider the prospect for the third that lies ahead.Opinions differ as to the relative importance of factors that have been responsible for the expansion and growth of Canada in its first hundred years. Some will say that it has been due to the abundance and fertility of agricultural land, others to the early enterprise of the railroads, and financiers believe that the banking system has been a major factor; -the fisherman -the forester -the teacher -each has his own view. I suspect, however, that most of us here would subscribe to the thesis of T. A. Rickard -miner, author, imperialist -who wrote, a gene-ration ago, ""Trade follows the flag, but the flag follows the pick,"" and thus agree that the finest contribution to progress, to wealth, to extension of frontiers and to inter-national trade has been provided by the mineral industry."

Jan 1, 1966

By J. Hedderson, J. Starkey, S. Reeves, B. Hilscher

"As ore sorting becomes more common, it is important to quantify its impact on comminution circuits in order to precisely predict its effect on throughput, grind, and mill operating conditions. Since sulphides and other valuable minerals are often softer then the surrounding waste rock, the ore kept by a sorting system is typically softer than the average ore. In order to accurately forecast production, new measurements of hardness need to be performed on the new concentrated mill feed. This paper proposes a methodology to examine this effect quantitatively at an early stage of project development using the SAGDesign test.INTRODUCTION The application of ore sorting in the mining industry is one of the most promising recent technologies with the potential to cause step change in the way concentrators are designed. Most typically, ore sorters are used to sort a given ore flow for grade, either to reject waste from the mill feed, or rescue ore from the waste pile. Ore sorting technologies have been successfully applied at many mining properties in various forms and while the technology has reached or is reaching maturity in other industries, it is still in development in the mining sector. As a result, there is not yet a general consensus on the considerations that need to be made when designing a plant with ore sorting from a feasibility level above and beyond what is commonly performed as best practice. This paper will discuss those considerations and propose a methodology for integrating ore sorting into a comminution circuit at the design phase. Due to the linearly additive nature of the SAGDesign Test results, a “hardness balance” can be developed to estimate the ore hardness which would be measured in any sorting mass split using only two data points. This will allow a design engineer to make more informed decisions as to the most appropriate mass split to select in relation to the incurred operating costs and grinding circuit sizing."

Jan 1, 2019

By E. H. Crabtree

IN an ideal mill, with perfect milling operations, the mineral extraction would be 100 per cent, the, concentrate would be 100 per cent mineral, the tailing would assay zer.0 mineral and the milling cost would be zero dollars. Such an operation can, of course, never be attained. We can only strive to approach it as nearly as possible and in doing so most recognize .the fact that the three primary factors in milling: assay of concentrate, assay of tailing, and cost of operation bear a definite economic relationship to each other. This relation will change from time to time and will be different for different mills, depending on milling equipment, character and quality of feed, market conditions, and other factors. It is granted that for a given operation there is an economic point, but the location of this point is difficult. It is for the purpose of making some of these economic points a little more tangible that this paper has been prepared.

Jan 1, 1930

By Leo H. Duriez, James V. Neuman

THE Bayard property of the united States Smelting Refining and Mining Company is in south central Grant County in southwestern New Mexico about fifteen miles east of Silver City and one mile west of Santa Rita. The present holdings cover a belt roughly one mile wide by ten miles long, lying west of, and adjacent to, the holdings of the American Smelting and Refining Co., Kennecott Copper Corp., Empire Zinc Co., and Peru Mining Co. The area extends from the village of Bayard on the south to a point three miles northeast of Fierro. The property is a part of the well-known Central mining district which has been New Mexico's leading copper-zinc producer for many years. The property is segregated into three sections, the Bullfrog, Hanover Bessemer, and the Shingle Canyon sections. Of these, the Bullfrog section covers the area between the towns of Bayard and Hanover and includes the Bullfrog No. 1, Bullfrog No. 2, Slate, Hobo,

Jan 1, 1948

By Joseph C. Buchen

IN principle, production of salt from sea water is a simple operation. Sea water is trapped in ponds, the sun and wind cause evaporation of the water, and what is left is principally salt. Commercial production of solar salt, however, requires a careful consideration of many factors. Obviously, sufficient evaporation must take place throughout the making season to produce an economically adequate crop. Other factors are density of soil, contour of ground, height of ground above sea level, minimum dilution from fresh-water streams, and distance from market. Unfortunately, in the United States the localities of greatest evaporation, allowing for the other factors, are not the most suitable for the manufacture of sea salt by solar evaporation. The south end of San Francisco Bay most

Jan 1, 1937

By Jinsheng Wang, Zhixiong You, Xuewei Lv, Yu Zhang, Jie Dang

Electro-titania slag is generally used as the raw material for titanium dioxide production by sulfate process. The phase composition of titanium as well as their disseminated grain size have significant effect on the acidolysis of titanium. Anosovite is considered as the most favorable Ti-bearing phase due to its high acidolysis ef ficiency, while silicates and rutile are not soluble in concentrated sulfuric acid. Different cooling rates will play a significant effect on the phase structure and particle size, which directly affects the acidolysis ratio of titania slag. In this paper, the influence on acidolysis ratio of titania slag at different cooling rates was studied. The results revealed that slower cooling rate resulted in the formation of larger particle size and a comparatively higher acidolysis ratio was obtained. On the contrast, rapid cooling was disadvantageous to the leaching of titanium as the smaller particle size anosovite was wrapped by glass phases.

Mar 1, 2018

The workshop on "Cyanide Effluents from Mineral Processing' was held on February 2-3, 1982, at the U.S. Bureau of Mines, Salt Lake City Research Center, Salt Lake City, Utah. The workshop was sponsored by the minerals industry, supporting industries, the National Science Foundation, and the U.S. Bureau of Mines through the Utah Mining and Mineral Resources Research Institute, College of Mines, University of Utah Prior to the workshop, a Working Paper was prepared and delivered to the participants. This paper was used as a guide during panel discussions and forms the basis for this proceedings document. The workshop focused on use of cyanide as it relates to the gold and silver mining industry and the froth flotation processes employed by mineral mining companies. Its intent was to discuss "state of the art" technology and provide information pertinent to cyanide use in the minerals industry. No attempt was made to advocate regulatory limits or set policy governing the use of cyanide. The principal topics of discussion included- (1) the chemistry and use of cyanides; (2) control and treatment of cyanide mining wastes; (3) toxicity of mining wastes; (4) fate of cyanide in the environment; and (5) the analytical chemistry of cyanide.

Jan 1, 1983

By Daniel Augusto Ferro

Devido crescente necessidade de elevação dos níveis de conformação em peças estampadas, existe uma demanda cada vez maior em ligas e processos diversificados que atendam as variadas exigências do setor de produtos estampados e posteriormente tratados termicamente para aumento de dureza. Desse modo desenvolveu-se a liga C80M (modificada), que é uma variante da liga C80U especificada na norma DIN EN ISO 4957 porém com adição de Cromo, entretanto a liga C80M ainda é pouco estudada e pouca informação técnica se tem a seu respeito. Com a finalidade de melhor conhecimento técnico dessa liga, foram conduzidos estudos de caracterização em amostras laminadas a quente e após processo de esferoidização posteriormente sendo revestidas com fosfato de zinco. Foram realizados estudos de composição química, microestrutura e propriedades mecânicas, além de levantamento da curva CLC através do método Nakazima em amostras com e sem revestimento de fosfato. Através dos resultados parciais encontrados, foi possível definir o lado da curva CLC relacionado ao estiramento da chapa bem como comparar o deslocamento e a força do punção no teste Nakazima conformando-se amostras esferoidizadas sem e com revestimento de fosfato.

Jul 30, 2018

By Daniel Augusto Ferro

O aço 27MnCrB5-2 tem sido muito utilizado para aplicação em facas, além de peças de boa resistência mecânica e resistência ao desgaste, alguns exemplos são verificados no ramo agrícola como faca para corte basal de colheitadeiras de cana, lâminas de roçadeira e helicoide para transporte de grãos. A indústria de beneficiamento de papel/papelão é outro segmento onde esse aço está presente, sendo usado para facas de corte e vinco. Com o objetivo de melhorar a conformabilidade da liga 27MnCrB5-2 no estado temperado, de forma a atender o nível de conformação solicitado, principalmente na fabricação de facas de corte e vinco, foram processados quatro lotes com diferentes conceitos de tratamento térmico de têmpera (martêmpera e austêmpera) para posterior avaliação das estruturas e propriedades mecânicas, a fim de correlacioná-las com a conformabilidade da dobra em cada situação. Com os resultados encontrados e testes práticos realizados durante fabricação da faca de corte e vinco, foi possível constatar melhora significativa na microestrutura/propriedade mecânica/processamento da peça considerando sua conformabilidade com um dos parâmetros de austêmpera utilizados.

Aug 16, 2017

By Caio Oliveira Biondi

A lixiviação de zinco é um processo contínuo que ocorre através da adição de ácido em uma série de tanques, com objetivo de extrair o zinco do material de origem. O ácido deve ser adicionado de forma progressiva para evitar a formação de compostos indesejados e também a formação de espuma decorrente da reação do ácido com o carbonato. O grande desafio do processo é acertar os pontos corretos de adição de ácido para que a lixiviação ocorra com o maior rendimento possível, pois tanto o excesso quanto a falta de ácido prejudicam essa etapa. Com o objetivo de aumentar o rendimento global do processo, a solução de controle avançado baseada em lógica Fuzzy da I.Systems, o Leaf, foi aplicado para substituir o controle tradicional PID e/ou manual. O Leaf foi capaz de reduzir a variabilidade do pH nos tanques em até 25%, fazendo com que fosse possível operar mais tempo no ponto ótimo. Isso permitiu que o rendimento global da etapa de lixiviação aumentasse 0,24%, além de melhoria qualitativa na etapa seguinte de sedimentação. O ganho financeiro proporcionado pela economia de concentrado silicatado foi de 375.000 reais por ano para a Votorantim Metais.

Oct 30, 2017

By Marcilio do Carmo Silva

O circuito de flotação de Fábrica Nova é composto por três colunas de quatro metros de diâmetro e quinze de altura, equipadas com sparger’s tipo retrofit (misturadores), utilizando uma mistura de ar e polpa para geração de bolhas. As colunas operam em paralelo constituindo o estágio rougher. Os produtos gerados neste estágio são tratados em células convencionais (cleaner e scavenger). Com o empobrecimento do ROM proveniente da Mina de Fábrica Nova e conseqüente aumento de SiO2 na alimentação da flotação, fez-se necessário ajuste no circuito com o intuito de garantirmos qualidade competitiva do pellet feed de Fábrica Nova. Foram feitas alterações de rota do rejeito do estágio rougher, direcionando o mesmo para o rejeito final (no circuito padrão o mesmo alimentava o estágio scavenger). O rejeito do rougher e o rejeito do scavenger compõem o rejeito final da flotação. Um ajuste no percentual de sólidos da alimentação da flotação foi necessário para favorecer a coleta da sílica (saindo da ordem de 58-60% para 53-54%). Com esta manobra conseguimos retirar o excesso de SiO2 do circuito de flotação, possibilitando a geração de pellet feed com qualidade dentro dos padrões VALE.

Aug 8, 2018

By Breno Totti Maia

Metalurgistas e pesquisadores de aciarias a oxigênio buscam dia após dia o desenvolvimento de parâmetros operacionais com reflexos diretos em ganhos metalúrgicos e no desempenho dos equipamentos, visando aumentar a produtividade e evitando interrupções para manutenção. O principal requerimento para um converterdor a oxigênio é o conjunto de lança com bico de cobre. Recentemente a Lumar Metals apresentou cartuchos com a tecnologia Slagless que podem ser usados para substituir os bicos convencionais de cobre com expressivos resultados de processo. Alguns pontos são fundamentais para se obter um projeto de bico que tenha satisfatória vida útil, como por exemplo, a estrutura do material utilizado, o correto dimensionamento do circuito de refrigeração e o correto dimensionamento dos lavais de saída do oxigênio. O objetivo do presente trabalho é avaliar os efeitos dos parâmetros de processo: pressão e vazão e suas influências no desgaste do bico de lança devido ao mau dimensionamento dos lavais ou quando operando em condições abaixo da especificada. Os resultados mostram que para cada conversor com um perfil operacional único, o projeto do bocal específico é o que garante os melhores ganhos metalúrgicos e aumento da vida útil do bico.

Aug 16, 2017

By Raimison Bezerra de Assis

Ferritas são compostos cerâmicos que apresentam propriedades magnéticas, sendo estas dependentes da sua estrutura cristalina. Dentre as ferritas, a do tipo Ni-Zn é uma das mais promissoras, em virtude da microestrutura e das propriedades magnéticas deste material. Este trabalho teve como objetivo analisar a microestrutura e propriedades magnéticas da ferrita Ni-Zn dopada com íons (TR) Sm3+. A ferrita Ni-Zn-Sm foi obtida pelo método dos precursores poliméricos, a partir da dissolução do ácido cítrico, nitrato de ferro, nitrato de níquel, nitrato de zinco, nitrato de samário e etilenoglicol. A resina obtida foi pirolisada a 350°C/2h com taxa de aquecimento de 10°C/min. e calcinada a 650°C/3h com taxa de aquecimento de 10°C/min. O material resultante foi caracterizado por difração de raios-X (DRX), microscopia eletrônica de varredura (MEV) e magnetometria de amostra vibrante (VSM). Os resultados mostraram a formação de fase única da ferrita Ni-Zn-Sm, com partículas aglomeradas e características magnéticas de material macio "soft", com baixa coercividade (0,189 kOe) e magnetização de saturação (47,699 emu/g).

Aug 8, 2018

By William H. King

The Nevada Massachusetts tungsten deposits (fig. 1) are in the Mill City Mining District in north-central Pershing County, Nev., about 37 miles southwest of Winnemucca. Contact metamorphism of thin limestone beds within a series of metamorphosed sedimentaries formed scheelite-bearing ore bodies. These deposits are distributed over a wide area. A Bureau of Mines development program was started January 11 d was completed on July 25, 1941. This work was centered on the outer and less explored beds in the district and comprised trenching, sampling, and diamond drilling. Exploratory work was done in cooperation with the U.S. Geological Survey. Project work substantially increased the reserve tonnage of marginal ore in three of the areas explored and proved the nonexistence of tungsten in a fourth area. The following pages summarize the history of the district, outline property ownership, and describe physical features and ore deposits. The plan and results of the work performed by the Bureau of Mines are presented along with geologic and topographic maps, assay maps, and diamond drill-hole logs.

Jan 1, 1950

By Enrique Levy

Central America is graduating this year into large scale mining with the start up of Inco's multi-million dollar nickel laterite processing plant in Guatemala. In the other extreme of the Isthmus in Panama Texas Gulf Sulphur is doing check diamond drilling and foundation test drilling at the Cerro Colorado copper porphyry. The higher price of gold and silver has spurred development and exploration of several small precious metal mines. The purpose of this presentation is to make a brief resumé of the most important mines operating in the area and a list of significant exploration projects. Also, tables will be shown to compare mining codes and taxes. Unfortunately these tables lack information on Panama. Before starting I like to express my appreciation to Kennecott Copper who permitted the use of some of the data compiled by the author on their behalf during the year 1975. Other persons which did not want to be named also have my gratitude.

Jan 1, 1977

By Oliver Gago Porras

Son diversas las técnicas que se han empleado para el reforzamiento de la roca durante el proceso de excavaciones subterráneas en la mina Quiruvilca. Sin embargo, los sistemas utilizados actualmente resultan inoperantes, dado que sus elementos de perno y anclaje no se complementan con el terreno señalado. En ese sentido, el presente texto describe el sistema idóneo para el sostenimiento de roca en el que el rendimiento estuvo enmarcado entre los pernos de anclaje y madera. Este método denominado "eslinga para roca", consiste en una combinación de elementos de refuerzo activo y de suspensión, cuya construcción permite aprovechar algunos recursos existentes en la mina.

Nov 24, 1986

By J. R. Goode

"Canada developed pioneering rare earth solvent extraction methods to recover the rare earths and thorium as by-products of uranium recovery operations in Elliot Lake, Ontario, and was a major supplier of these key elements from about 1960 until 1990. At one stage, Elliot Lake was supplying perhaps one third of the world’s yttrium as well as much of its thorium. This paper reviews the development of Canada’s early rare earth and thorium production facilities. INTRODUCTIONThe rare earths and thorium were first identified in the early 19th century but were little more than curiosities for the next century. However, in the mid-1960s the invention of rare earth-based phosphors for the cathode ray picture tube used in colour television sets launched a major demand for certain rare earths.The use of thorium as an alloying agent in aircraft and missiles grew rapidly in the late 1950s. In the same period, demand for uranium for both weapons and power production soared. Also in the late 1950s, the Elliot Lake uranium-thorium-rare earth deposits (also known as the Blind River deposits) were discovered. This conjugation of events led to uranium production in the Elliot Lake camp, quickly followed by the co-production of thorium and, later, the rare earths.Uranium production in the Elliot Lake camp continued from 1955 to 1996. Thorium was produced continuously from 1959 to 1969. Rare earths were produced, intermittently, from 1965 to 1990. Complete production records are not readily available but unquestionably Elliot Lake made a significant contribution to world thorium and the rare earth production. This paper, presented earlier in an abbreviated form (Goode, 2012), is intended to present as much of the information that is available."

Jan 1, 2012

By AIME AIME

WHEN "Chief" Buehler in mid-September set out on his official 10,000 mile swing-around-the-circle visiting Local Sections he decided not to tell his audiences how to organize and operate a state geological survey. As the director for 28 years, of the Missouri Bureau of Geology and Mines (which, he concedes, is the best in existence) lie could have done this to good advantage; but he preferred to discuss affairs of the Institute. In 25 speeches made to member and student groups, he dwelt on sonic or all of the following phases of activities. He stressed the vital importance of the Local Sections in providing the opportunity for members to associate under pleasant auspices with others in their profession. The benefits of Institute membership he classified as tangible and intangible. Of the two lie felt that the latter were more important. A man's progress in his profession depends in large measure upon a broad acquaintance and friendship with others. The Institute is incomparably the best medium for meeting fellow engineers. The primary, function of the new enlarged Membership Committee is to obtain a comprehensive list of engineers eligible to be members, always hearing in mind that the standards of membership must not be lowered in any degree. These men are to be invited by individual letter to apply for membership. Whether they become members or not is of less importance; but it is vital that no qualified man should be outside the fold for the reason that membership had never been suggested to him. Dr. Buehler emphasized repeatedly his feeling that the younger man that had never had Institute membership brought specifically to his attention had been cheated:

Jan 1, 1935