Search Documents

By John Hanna

Over the years the coal industry in Alabama has generated about 150 million tons of fine waste coal, increasing at a rate of 2 million tons/year, during mining and cleaning operations. Reclamation of the fine-size wastes containing 20-60% by weight clean coal provides, free of charge, mined and crushed feedstocks for coal recovery and eliminates a major source of acid water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the plus 100 mesh material produced commercial grade coal averaging 8.2% ash, 0.8% sulfur and 13,350 Btu/lb. However, the coal recovery was relatively low at 50-65%. Froth flotation using mechanical and froth column methods gave similar coal products at much higher coal recovery of 87-93%. The coal produced analyzed 10% ash and 1.1% sulfur.

Jan 1, 1991

By H. Schultz

Urban refuse that was mechanically separated at the U S Bureau of Mines pilot plant in College Park, Md., was successfully evaluated for its fuel values using standard coal analysis methods. Analyses performed on refuse samples taken from five sample points included moisture, ash, sulfur, chlorine, and heating value. It was recommended that characterization of the combustible portion of urban refuse by standard coal analysis procedures should be widely adopted.

Jan 1, 1975

By Charles B. Kenahan

Application of ultrasonics in the electrolytic deposition of metallic manganese and manganese dioxide from sulfate electrolytes had several effects. Ultrasonics produced finer-grained deposits of electrolytic manganese at all current densities than obtained in normal cell operation, but at high current densities it resulted in less adherent deposits. Ultrasonic radiation did not affect cell voltage or cathode current efficiency. In the electrodeposition of manganese dioxide at 70° C., ultrasonic-; increased the current efficiency and decreased the cell voltage at a current density of 9 amperes per square foot, but it had little effect at current densities above this. The decrease in cell voltage was caused by the depolarizing action of ultrasonics at both anode and cathode. Ultrasonic radiation produced a smooth, glossy, adherent, and pit-free deposit at all current densities and at each temperature. Radiation had no effect on current efficiency or cell voltage at 90° C. Ultrasonics was more effective than conventional agitation in producing all of these effects.

Jan 1, 1962

By Arnulf P. Hagen

This project was designed to explore the suitability of using fluorinated inorganic materials as solvents for the in situ mining of thin seamed, heavily overburdened coal; to build a data base for the selection of an inorganic solvent for use for coal cleaning; to determine if fluorinated solvents will reduce the organic and inorganic sulfur contents of the coal, as well as to lower the ash content. The coal samples have been combined with pure solvent, as well as with aqueous solutions at atmospheric pressure and at increased pressure. The increased pressure experiments are important since they duplicate the conditions anticipated for an in situ cleaning and mining operation. Trifluoroacetic, difluorphosphoric (phosphorodifluoroidic), and trifluoromethanesulfonic acids have been found to be effective for the cleaning of high sulfur, high ash coal at 300°C and at atmospheric pressure. At pressures up to 20,000 psi the effectiveness of these reagents is not decreased.

Jan 1, 1983

By Walter E. Lewis

The Fort Randall Reservoir project, on the Missouri River at Pickstown, S. Dak., was designed by the Corps of Engineers and is part of the Missouri River Basin Development Program. The location of the project with respect to adjacent features is shown' in figure 1. When the project is finished, it will include a large earthwork dam and 12 circular tunnels, 8 of which will be equipped for power and 4 for flood control. Various phases of the construction have been contracted to independent companies, and at present four companies are working on different phases of the project under a rigid time schedule. Western Contracting Corp. is the contractor on stage II, earthwork; Johnson-Winston Construction Co. is the contractor for construction of the intake towers at the upstream side of the dam; McCarthy Improvement Co. has the contract for the power house and the outlet works on the downstream side; and Silas Mason Co. has the contract for driving the power and flood-control tunnels. The latter two companies use the same roads for ingress and egress to their respective work areas and the same general waste dump area. Under such circumstances, it is necessary that each company stay on a time schedule in regular sequence to avoid interference with the other.

Jan 1, 1951

CONTENTS RUSSIA-R. C.-BECKSTROM 3 VENEZUELA-F. H. KAY 9 TRINIDAD-W. J. MlLLARD 20 RUMANIA-1. I. GARDESCU 26

Jan 1, 1932

No paper available.

Jan 1, 1996

By W. S. Morris

PETROLEUM'S importance in World War II can perhaps be better realized by the recitation of a few facts and figures: Gasoline needs in this war are already eighty times greater than in the last war. It takes nearly three pounds of gasoline to deliver one pound of bombs, filled with petroleum explosives, on an enemy objective. Every American soldier overseas requires an average of more than fifty gallons of petroleum products per week, with the oil used by Navy and supply ships and America's Allies boosting the consumption of oil per soldier to an even higher figure. Every oil well in the United States now must produce each day an average of four barrels of oil for war and combat jobs. More than fifty million gallons of gasoline, fuel oils, lubricants, and other petroleum products are now going directly to the fighting forces every day.

Jan 1, 1945

By Pedro Jorge Walburga Keglevich de Buzin

A produção siderúrgica em usinas semi-integradas gera vários tipos de resíduos dentre os quais as carepas. No presente trabalho estuda-se o comportamento físicoquímico em altas temperaturas de briquetes autorredutores elaborados com carepa e finos de carvão vegetal produzidos no Rio Grande do Sul, objetivando sua introdução no processo produtivo de aciaria elétrica. Ensaios realizados em laboratório com briquetes industriais confeccionados com estes resíduos demonstraram a potencialidade de utilização destes briquetes autorredutores em processos siderúrgicos via forno elétrico a arco (FEA).

Aug 16, 2017

By Donald O. Rausch, William E. Hawkes, Odin Jr. Strandberg

INTRODUCTION Kennecott Copper Corp.'s Tintic Div. Burgin mine is a 725 t/d (800 stpd) lead-zinc producer, located in the east Tintic mining district, 5.6 km (3.5 miles) east of Eureka, and 130 km (80 miles) south of Salt Lake City, UT. The Burgin mining complex includes three shafts, shop, dry, and office facilities, and a 454 t/d (500 stpd) flotation concentrator. Production and ser¬vice entry to the mine is through a 4.26-m (14-ft) diam concrete-lined production shaft, and a three-compart¬ment rectangular shaft. A connection with the Apex No. 2 shaft and the Burgin mine provides a second exhaust airway. Bear Creek Mining Co., Kennecott's exploration sub¬sidiary, began exploration of the Burgin mine area in 1957 with the sinking of the 335 m (1100 ft) deep No. 1 shaft. A station was cut at the 320-m (1050-ft) level of the shaft and extensive drifting, diamond drilling, and some winzing and raising confirmed the presence of a major lead-zinc ore body, the main portion of which oc¬curred below a hot saline water table. Surface facilities and the 4.26-m (14-ft) diam concrete-lined production shaft were completed in 1966. Ore production has been steadily increased to 725 t/ d (800 stpd) since 1966. The collar elevation of the No. 2 production shaft is 1731 m (5678 ft) above sea level. The mine's three levels, the 1050, 1200, and 1300 are at elevations of 1414.6, 1356.4, and 1338.1 m (4587, 4450, and 4390 ft), respectively. The approximate elevation of the hot saline water table is 1382.6 m (4536 ft). The earliest production on the east Tintic mining district was from the Eureka Lilly mine in 1909. Later, in 1916, the Tintic Standard mine was discovered, and pro¬duced ores with a gross value of $80,000,000 through 1956. The Eureka Standard mine located 1.6 km (1 mile) southwest of the Burgin mine produced ore worth $12,000,000 from fissures in the Tintic quartzite along the Eureka Standard fault. Ores produced from the east Tintic mining district through 1971 are valued at $151.3 million. The production from the entire Tintic district is approximately $500 million. GEOLOGY The Burgin ore deposit occurs as replacement bodies in limestone, dolomite, and shale. Numerous fault struc¬tures and rock formations make the mine geology com¬plex. The mineralization is strongly associated with sev¬eral major geological features, which include the Ophir formation, consisting of limestone, dolomite, and shale as the favorable host rock, and the structural influence of the east Tintic thrust, the Eureka Standard and sev¬eral other significant faults. Fig. 1 depicts the Burgin 1300 level workings, a generalized configuration of the ore body, and the main geological features. Covering the quartzite, limestone, dolomite, and shale facies enclosing the Burgin ore deposit are 183 to 274 m (600 to 900 ft) of andesite. The Burgin ore consists of massive sulfide and oxide lead-zinc ores with significant silver and cadmium val¬ues. The main ore minerals are galena, cerrusite, and spalerite. Extensive manganese oxide deposits are associated with the lead-zinc ore occurrence. A limited

Jan 1, 1982

By Simón D. Strauss

El presente estudio revisa la evolución de la producción de los principales minerales (plomo, cobre y plata) en Estados Unidos desde la década del 70, asi como su repercusión en Chile, Perú y algunos países latinoamericanos. En esta perspectiva, se pronostican algunos datos sobre los cambios políticos, sociales y económicos que ocurrirán dentro de los próximos 28 años y que afectarán la demanda de productos minerales y la capacidad para producirlos.

Nov 20, 1972

By Jack F. Harang, P. B. Leavenworth

Development during the year 1941 on the Texas Gulf Coast resulted in the dis covery of 27 new fields as compared to 26 fields for the year 1940. Drilling.—During the year, 1405 wells were drilled. Of this number, 1031 were completed as oil wells with 375,000 bbl. daily of new production; 50 were com pleted as gas wells and 324 were failures. The most active area was Jackson County, where 375 wells were drilled and 336 of them accounting for 190,000 bbl. daily of new production. Types of Fields.—Of the 2 7 new fields, 14 are considered to be oil fields, 8 are listed as gas-distillate fields and 5 as gas fields. This may be compared to 26 fields found in 1940, of which 14 were oil fields and 12 gas-distillate fields. Producing Sections.—Frio discoveries retained their predominant position by having 10 Frio fields discovered in comparison to 6 fields in the Wilcox, 4 in the Yegua, 5 in the Miocene and 2 in the Jackson. In the previous year 15 Frio fields were found, 4 in the Wilcox, 2 each in the Yegua, Cook Mountain and Miocene, and I in the Jackson. Production.—Production increased over 1940 approximately 10 per cent, being 113,726,893 bbl. for the year 1941 and 104,127,247 bbl. for 1940. The statistics in Tables I and 2 include distillate and condensate as oil production because no separate reports have been compiled. It is hoped that this separation may be possible some day, but as a great many fields produce both oil and distillate and these arc commingled in pipe lines, separation of statistics will be more difficult than for other areas. New Fields Big Hill, Jefferson County.—Stanolind Oil and Gas Company's No. I George D. Anderson was completed as a gas well from a Frio sand at 8705 to 8720 ft., on Dec. 24, 1941, after having been drilled to a depth of 9500 ft. Additional development is being carried on but it is not possible to evaluate this discovery at this time. Brushy Creek Field, Lavaca County.— Shell Oil Corporation's No. I D. G. McManus was completed as the discovery well in the Brushy Creek field on Oct. 29, 1941, from a Wilcox sand through perforations at 7225 to 7230 ft., making gas and 180 bbl. of 59° gravity distillate. This well was bottomed at 10,998 ft. in the Wilcox. No statement can be made at this time as to the importance of this discovery. Chenango Field, Brazoria County.—J. N. Rayzor et al. completed their No. I Sarah J. Christian through perforations at 8564 to 8572 ft. in a Frio sand, for 453 bbl. of 37.7° gravity oil, on Feb. 6, 1941, after having drilled to 9564 ft. Several wells were drilled in this area during the year but failed to establish important production. This is considered a minor discovery. Clodine Field, Fort Bend County.—Providence Oil Company's No. I Hatfield was the discovery well of the Clodine field, being completed through perforations at 7499 to 7502 ft. for 108 bbl. of 51.2° gravity distillate, on June 19, 1941. The well was bottomed at 8090 ft. Several wells

Jan 1, 1942

By P. B. Leavenworth, Jack F. Harang

Development during the year 1941 on the Texas Gulf Coast resulted in the dis covery of 27 new fields as compared to 26 fields for the year 1940. Drilling.—During the year, 1405 wells were drilled. Of this number, 1031 were completed as oil wells with 375,000 bbl. daily of new production; 50 were com pleted as gas wells and 324 were failures. The most active area was Jackson County, where 375 wells were drilled and 336 of them accounting for 190,000 bbl. daily of new production. Types of Fields.—Of the 2 7 new fields, 14 are considered to be oil fields, 8 are listed as gas-distillate fields and 5 as gas fields. This may be compared to 26 fields found in 1940, of which 14 were oil fields and 12 gas-distillate fields. Producing Sections.—Frio discoveries retained their predominant position by having 10 Frio fields discovered in comparison to 6 fields in the Wilcox, 4 in the Yegua, 5 in the Miocene and 2 in the Jackson. In the previous year 15 Frio fields were found, 4 in the Wilcox, 2 each in the Yegua, Cook Mountain and Miocene, and I in the Jackson. Production.—Production increased over 1940 approximately 10 per cent, being 113,726,893 bbl. for the year 1941 and 104,127,247 bbl. for 1940. The statistics in Tables I and 2 include distillate and condensate as oil production because no separate reports have been compiled. It is hoped that this separation may be possible some day, but as a great many fields produce both oil and distillate and these arc commingled in pipe lines, separation of statistics will be more difficult than for other areas. New Fields Big Hill, Jefferson County.—Stanolind Oil and Gas Company's No. I George D. Anderson was completed as a gas well from a Frio sand at 8705 to 8720 ft., on Dec. 24, 1941, after having been drilled to a depth of 9500 ft. Additional development is being carried on but it is not possible to evaluate this discovery at this time. Brushy Creek Field, Lavaca County.— Shell Oil Corporation's No. I D. G. McManus was completed as the discovery well in the Brushy Creek field on Oct. 29, 1941, from a Wilcox sand through perforations at 7225 to 7230 ft., making gas and 180 bbl. of 59° gravity distillate. This well was bottomed at 10,998 ft. in the Wilcox. No statement can be made at this time as to the importance of this discovery. Chenango Field, Brazoria County.—J. N. Rayzor et al. completed their No. I Sarah J. Christian through perforations at 8564 to 8572 ft. in a Frio sand, for 453 bbl. of 37.7° gravity oil, on Feb. 6, 1941, after having drilled to 9564 ft. Several wells were drilled in this area during the year but failed to establish important production. This is considered a minor discovery. Clodine Field, Fort Bend County.—Providence Oil Company's No. I Hatfield was the discovery well of the Clodine field, being completed through perforations at 7499 to 7502 ft. for 108 bbl. of 51.2° gravity distillate, on June 19, 1941. The well was bottomed at 8090 ft. Several wells

Jan 1, 1942

By A Guillen, J-P ChilFs

Most 3D geological modelling tools were designed for the needs of the oil industry or detailed mine planning and are not suited to the variety of situations encountered in other application domains. Moreover, the usual modelling tools are not able to quantify the uncertainty of the geometric models generated. The potential field method was designed to build 3D geological models from data available in geology and mineral exploration, namely the geological map and a digital terrain model (DTM), structural data, borehole data and interpretations of the geologist. This method considers a geological interface as a particular isosurface of a scalar field defined in the 3D space, called a potential field. The interpolation of that field, based on cokriging, provides surfaces that honour all the data. The 3D model and its parts are always consistent with the observations. New developments allow the covariance of the potential field to be identified from the structural data. This makes it possible to associate sensible cokriging standard deviations to the potential field estimates and to express the uncertainty of the geometric model. It also, for the first time, gives a statistically optimal, geologically sound way of interpolating geology, other than directly joining the dots as you do with CAD. Practical implementation issues for producing 3D geological models are presented: how to handle faults, how to honour borehole ends, how to take relationships between several interfaces into account, how to model thin beds over many kilometres, how to optimise lithological properties and how to integrate gravimetric and magnetic data. We describe all geology surfaces and volumes using implicit functions. These are then rendered onto the required sections, plans, etc. The estimation of orebody grades and tonnes, using an unbiased and optimal geostatistical technique, makes use of the stratigraphically bound 3D geology model. An application to the geological modelling of the Hamersley iron ore district, Australia, is briefly presented.

Jan 1, 2009

By J. A. Cox, R. S. Mattson

"One of the main problems encountered in employing sublevel caving is the inherent high dilution factor. The operating results at Granduc illustrate that this dilution can be closely controlled and satisfactory recoveries achieved, in base metal ores grading less than 2.0% copper equivalent, by using an assay grade control system based on the fundamental draw characteristics. The history of draw control procedures employed since the start of operations provides an effective comparison between this system and one based mainly on tonnage. The transverse and longitudinal sublevel caving mining methods are described and it is shown how improvements in design layout, operating practice and draw control in narrow complex ore zones (12-foot minimum width) have raised the operating performance of the longitudinal system to a satisfactory level."

Jan 1, 1973

By AIME AIME

HE State of Utah has an area of 84,990 sq. mi., and like other inland states in the West its population, although steadily increasing, is relatively small. The fact that it is a state possessing vast mineral resources is attested by a careful study of statistics which have been compiled by Federal and State investigators. Some idea of the extent of these resources and the degree of development of a particular state or region may be gained by such a study, but in the case of Utah statistics and other available information fail to portray completely the true extent and value of its existing metallic and non-metallic resources. The State is probably more widely known for its production of metallic ores which has placed it in an eminent position among the metal mining states of the Nation.

Jan 1, 1925

By B. R. Conard

Copper refining at Vale Canada (previously known as Inco) has been associated with Ni production. Because Cu and Ni carry risks for adverse health endpoints through inhalation exposure, it is critical that their aerosol levels, and the metallurgical processes through which they enter the air, are understood. Because certain Ni substances have been linked to respiratory cancers, it is also important to characterize the amounts and types of Ni compounds in occupational settings. This paper describes electrorefining and electrowinning operations near Sudbury, Ontario (1930–present), and gives aerosol measurements (1978–present).

Jan 1, 2014

By H. E. Searle, Robert J. McKay, O. B. J. Fraser

The practical study of corrosion requires consideration of its economic aspects. It must be based on sound scientific principles, but it should be borne in mind that probably the most important object of a corrosion test is to determine what metal in corrosion-resisting construction will produce the greatest operating profit. Thus the corrosion test must be directly connected with money values or it is not a practical corrosion test. This, perhaps unusual, connection between corrosion and economics is partially due to the fact that corrosion deals only with the time factor or duration of equipment, and it is almost the only test which deals with this feature. In these statements a departure is made from the academic definition of the word corrosion and it is done deliberately. The use of the term corrosion is unusual. It is as though we spoke of a tensile test as a "breaking" test. We are not interested primarily in the break but in the strength of the metal. There is no English word which expresses our main interest in corrosion-testing, but let us have clearly in mind that we make corrosion tests to prevent corrosion. Our real interest is in this corrosion-prevention, not in the corrosion. Previous to 1922, it was common comment that "it is impossible to determine the course of corrosion by laboratory testing.'' This statement was true at that time in that the technique of laboratory testing for corrosion resistance was so vague that tests in the laboratory gave untrue results almost as often as true ones. This was so, even in the simple case of determining which one of two metals better resists a given solution. While this is no longer true the number of misleading "corrosion tests" still being ground out by laboratories is too large in the light of our present knowledge. There are two important features of corrosion testing whose neglect is a large contributing factor to misleading results: (1) The economic relations of the corrosion tests to other tests; (2) testing technique. Regarding economic relations J. F. Thompson l has said: "The use of any particular metal is rarely based upon the sole property of resistance to corrosion. In fact, I should like to venture the assertion

Jan 1, 1929

By Robert J. McKay, O. B. J. Fraser, H. E. Searle

The practical study of corrosion requires consideration of its economic aspects. It must be based on sound scientific principles, but it should be borne in mind that probably the most important object of a corrosion test is to determine what metal in corrosion-resisting construction will produce the greatest operating profit. Thus the corrosion test must be directly connected with money values or it is not a practical corrosion test. This, perhaps unusual, connection between corrosion and economics is partially due to the fact that corrosion deals only with the time factor or duration of equipment, and it is almost the only test which deals with this feature. In these statements a departure is made from the academic definition of the word corrosion and it is done deliberately. The use of the term corrosion is unusual. It is as though we spoke of a tensile test as a "breaking" test. We are not interested primarily in the break but in the strength of the metal. There is no English word which expresses our main interest in corrosion-testing, but let us have clearly in mind that we make corrosion tests to prevent corrosion. Our real interest is in this corrosion-prevention, not in the corrosion. Previous to 1922, it was common comment that "it is impossible to determine the course of corrosion by laboratory testing.'' This statement was true at that time in that the technique of laboratory testing for corrosion resistance was so vague that tests in the laboratory gave untrue results almost as often as true ones. This was so, even in the simple case of determining which one of two metals better resists a given solution. While this is no longer true the number of misleading "corrosion tests" still being ground out by laboratories is too large in the light of our present knowledge. There are two important features of corrosion testing whose neglect is a large contributing factor to misleading results: (1) The economic relations of the corrosion tests to other tests; (2) testing technique. Regarding economic relations J. F. Thompson l has said: "The use of any particular metal is rarely based upon the sole property of resistance to corrosion. In fact, I should like to venture the assertion

Jan 1, 1929

By Oliver Bowles

This report covers the character, properties, origin, occurrence, and uses of the traprocks and describes briefly the methods and equipment employed in quarrying and preparing them for market. Production of traprock occupies an important place in industry. In 1960 the output in the form of crushed stone reached nearly 58 million tons valued at $87 million. Traprocks are also shaped into blocks of dimension stone for monuments, building construction and decoration, and specialized products such as surface plates.

Jan 1, 1963