Search Documents

By Dennis A. Clark, Brent Larsson

Tunnelling today is a lot more than drilling and blasting. The developments in drilling and blasting technique have made it pos¬sible to save costs both by increasing the advance per round and optimizing the demands on the final contour. Increasing the hole depth by using longer feeds and bigger dril¬ling rigs make the drilling time shorter compared to the set up time. It is important that the deeper holes are followed up by using a suitable cut. The most common cut in Sweden today is a parallel hole cut with one or more large holes; with a diameter corresponding to the hole depth and wanted advance per round. It is often specified that smooth blasting is to be carried out with a specific drill hole spacing. It is extremely rare, however, for specifications to be issued concerning the alignment of the raw of holes closest to the contour holes. It is very easy to ruin the effect of smooth blasting altogether by firing the rest of the round carelessly with an excessively high charge distribution. The drilling and blasting of the contour holes and the line of holes closest to the contour holes is therefore an extremely important part of any underground work. Accuracy and care in connection with the drilling of contour holes is also extremely important since it is possible to reduce the amount of overbreak, the result being more rapid mucking out, smoother and more durable surfaces and also less consumption of concrete for lining purposes.

Jan 1, 1983

By Little T. N

The Western Australian School of Mines is continuing to investigate the blasting techniques and mining strategies that are used for ore/waste separation (or high grade/low grade ore separation) or to prevent ore and waste mixing. The aim of all the mining strategies is to produce an optimum product. The optimum product is one which contains no diluent and undergoes no mixing of the various identified ore and waste blocks and is fully recovered at the minimum overall operating cost. The current study includes the use of computerised Knowledge Based Systems (KBS) technology to assist the user with the blast technique selection and blast design process. These aspects are highly dependent on the geology. (geometry, rock mass properties, grade distribution), explosive performance and the expectations of the mining company in terms of production rates and equipment utilisation. Most of these factors are not well defined and nor are they easy to quantify. However, a large amount of knowledge does exist and is available in the following forms: rules of thumb, empirical formulae, engineering judgement and past experience. KBS techniques are well adapted to handle such"forms of knowledge. The primary objective of this paper is to illustrate an approach for the use of Knowledge Based Systems during the analysis and interpretation stages of the blast design process. In particular, the components and methodology of the developed system are described for selective open pit gold mining. The Knowledge Based System developed was written using the declarative programming language PROLOG.

Jan 1, 1990

By Ivor da Cunha

Ontario Mining Association (OMA) represents 57 members that are engaged in exploring, producing & processing mineral resources in an environmentally responsible manner. Conservation Bureau at the Ontario Power Authority (OPA) develops, coordinates and stimulates commitment to electricity conservation and demand management programs ? OMA selected compressed air optimization for high impact cost savings and energy efficiency potential ? Ontario Power Authority (OPA) provided $218k funding for $532k project ? Commenced summer 2006, Final Report June 2007 ? Three representative sites participating: ? Williams, CVRD Inco & FNX McCreedy ? Different levels of energy management ? Small, medium and large mining operations ? Different corporate practices and culture

May 1, 2007

By Neil B. Prenn

Mine Development Associates, Inc. was formed in March of 1987 to provide mine engineering assistance to the mineral industry. To be competitive with other firms, Mine Development must be able to provide quick and accurate ore reserves and mine plans for clients. Commercially available mining software was necessary for Mine Development to assist the client. This paper describes how Mine Development chose mining software, the time involved in getting up to speed, and several case histories of how the software is used. The case histories discussed include: * 3,000,000 ton gold deposit in Nevada. * 5,000,000 ton gold deposit in South Dakota. * 1,000,000 ton gold deposit in Australia. * +100,000,000 ton gold deposit in Nevada. * 25,000,000 ton carbonate deposit in California.

Jan 1, 1989

By J. A. Russell

IT IS the purpose of this paper to show how the design of the larger slope hoists in use in the mines of the Dominion Steel and Coal Corporation has tended to evolve ta suit the particular conditions of operation. These hoists are all used for hauling coal in trains or trips of pit tubs up the mine slopes, which usually follow the dip of the seam . As the mine is developed to the dip and the slope grows in length, the length of the rope and the size of the hoist required to handle it rends to become extremely cumbersome. It has been found that the best economic conditions of hoisting are obtained when the length of the slope is limited to about seven or eight thousand feet. Beyond this length it is necessary to offset to one side of the line of slope and start a second or auxiliary slope, which will be served by its own hoist installed underground. With this hoisting distance as a basis, we find that we can economically hoist the outputs required, usually about 1,500 tans per eight hours per slope, by hoisting the coal in trips of about twenty boxes. This, on the grades obtaining, will require a rope of about l 1/4in. diameter, running at a speed of 1,200 ta 1,800 feet per minute, and requiring from 1,200 to 1,800 h.p. at the hoist shaft. The tendency is for the rope speeds of the surface hoists to be a little higher than the underground hoists which relay to them, so that the surface hoist has a small margin of time in hand. The oldest surface hoists were steam-driven, but, with few exceptions, these have given place to electric hoists. With the exception of one hoist, which was altered in design, the steam hoists have not had the opportunity of evolving in the same way as the electric hoists, and will not be mentioned any further.

Jan 1, 1944

By The Hollinger Mill Staff

ALTHOUGH cylindrical grinding mills have long been used, there is wide divergence of opinion as to what constitute best operating conditions. Questions such as mill diameter, diameter-length ratio, revolutions per minute, type and size of grinding media, volume of charge, circulating load, pulp level, pulp consistency, liner design, and size of feed, have all been given serious consideration by competent scientific investigators as well as by operators. While many laboratory and plant tests have been made that would seem to justify certain definite conclusions, there is a dearth of definite data giving actual results obtained when a grinding mill working between fixed limits is operated at its maximum capacity under varying conditions as to ball load, circulating load, speed, etc. In tests conducted recently at the Hollinger, extending over a period of thirteen months, to determine the best operating conditions for a ball-mill 6 ft. 6 in. diameter inside the liners, some very interesting facts have been ascertained. This paper is presented in the desire to make public the results of these tests and not with the idea that the last word has been spoken in regard to grinding. We feel, however, that these facts justify certain definite conclusions and hope that, by the fullest and frankest criticism and discussion, the essentials necessary for the correct design and operation of grinding mills will become better known.

Jan 1, 1937

By H. M. Howe

It has seemed to the writer that one important, and indeed sufficient reason, for our slow progress in learning the relation between the chemical composition and the physical properties of cast-iron, has been that the problem has not been attacked properly. It would be well to select the most probable working hypothesis which we can find, and proceed to test that hypothesis by comparison with observed facts, and by making new observations specially designed for such a test. Our first step, then, is to select the most probable working hypothesis ; and to attempt this selection, to state the hypothesis and its immediate corollaries, and to take some first steps toward testing it, is the object of the present paper. Its chief purpose is to bring the hypothesis to the attention of those who are more familiar with the evidence than the writer can pretend to be, and in a better position both to present new evidence and to discuss it. The hypothesis here selected is, that composition governs properties in the case of cast-iron, in the same general way and for the same reasons as in the case of steel, mutatis mutandis. This hypothesis, which of course makes no claim to originality, certainly seems reasonable and probable; its exposition and discussion are made easy by our existing knowledge of the constitution of normal or " carbon " steel; it therefore seems worthy of consideration.

Jan 1, 1902

By Will H. Coghill, I. L. Feld, G. D. Coe

The object of this paper . is to make known the superior classification accomplished in a hydraulic classifier designed to make use of principles determined by recent research ... The details of the design , the results of preliminary research , and the final testing are given . The classifier of the new design shown in figure 1 and another one like it are in operation as concentration classifiers in a Birmingham iron- ore mill recovering 4 tons per hour of concentrates from table middling that ` otherwise would require regrinding and retabling . The four factors that contribute to the successful operation of these classifiers are ( 1 ) a teeter column of small diameter , ( 2 ) use of an open - bottom tooter column classifier with a periodic pincer instead of the usual type , which terminates in a vortex, ( 3 ) a sorting chamber under separate hydraulic control , and ( 4 ) a teeter column of more than the usual depth . · At the outset it must be stated positively what the authors mean by hydraulic classification : They mean the reconstruction of a multimineral ground product into fractions graded with respect to size , so that cach fraction has the heavy mineral segregated in the fine sizes and the light mineral segregated in the coarse sizes . This definition presupposes that in multiplespigot classification the low specific gravity minerals are carried beyond the first cells to the later ones . The reader must take into account that , from the standpoint of classification , " ores " may be divided into two types , represented - by the following : ( 1 ) Joplin flint - blende ores , which , because of the hardness of the flint and the softness of the blonde , yield upon comminution a product that already has the essence of classification ; and ( 2 ) Birmingham Big Seam iron oros , which contain " easily shelled - out " sca sand and , upon reduction to about 10 mesh , yield a heterogeneous mixture in which the size analyses of the respective " floats " and " sinks " arc almost identical .

Dec 1, 1945

By E. Knell

COM Energy, Inc., a subsidiary of Occidental Petroleum Corporation, has constructed a 1.6 million hectoliter-per-year COM plant in Jacksonville, Florida. COM will be distributed to customers in the region as a substitute for fuel oil presently burned in boilers and kilns. As the market for COM grows, COM Energy, Inc. expects to build additional units both in this country and overseas. This paper addresses the overall status and technical aspects of the project, focusing on the facilities for COM production and utilization.

Jan 1, 1982

By Fred Hodges

This paper describing the concentrator practice of the Hurley Plant of the Nevada Consolidated Copper Co. at Hurley, N. Mex., is one of a series of papers on milling methods and costs being prepared by the United States Bureau of Mines. The Hurley concentrator has a normal daily capacity of 13,500 tons of ore, and for the first four months of 1930 the heads of the concentrator averaged 1.32 per cent of copper and 3.14 per cent of iron. The recovery for this period was 83.98 per cent and the concentrates produced averaged 27.54 per cent of copper.

Jan 1, 1931

By W. L. Crentz

Knott County is one of the smaller coal-producing areas in the Eastern Kentucky coal field. It contains numerous coal beds, many too thin to support mining over a wide area, Coal produced in the county is from a few rail-shipping operations and many small truck mines. Many smaller mines are working beds whose exact location in the coal-bearing strata is uncertain. Samples were collected from 11 different coal beds, of which the Fire Clay, Hindman, Upper Elkhorn No. 3, and Flag are the most import ant from a product ion standpoint. Known reserves in the Hindman bed. are very limited, and almost the entire production from this bed is gathered from two comparatively, large rail-shipping mines in addition to the four principal beds, samples were taken in the Francis, Haddix, Fire Clay Rider, Whitesburg, Amburgy, Upper horn No. 2, and Upper Elkhorn No. I .beds. Figure 1 is a typical section of the strata, showing the more important coal beds and. readily identifying their location with respect to each other. The bed names as shown are particularly important because of the local tendency to assign several names to the same bed. To avoid confusion, the names by which each coal bed is known also are given in the following listing. The coal. beds., in descending order, follow: [ ]

Jan 1, 1953

By Panlop Huttagosol

The use of computer models to design ultimate pit limit of an open pit mine during its feasibility study has become an emphasized procedure in mining. It is a normal practice in open pit mine design to generate the most profitable final pit limit. The limitations of designing this optimal pit limit have been the requirement of significant computing efforts as well as the use of complicated operations research techniques. In an attempt to describe a computer method that has an easy conceptualization and is able to provide a precise and desirable solution, a new technique is developed. The ultimate pit limit problem is formulated as a large scale transportation problem. The formulation is based on the use of a three dimensional block model to represent an ore body and surrounding materials. The solution technique is developed through solving the dual system of the formulated problem by using the adapted simplex algorithm of linear programming. The implementation on given case studies demonstrates that the new method is capable of providing an optimum pit value. The computing effort required by the algorithm is still the main constraint in solving a large scale problem. The technique provides open pit mine planners with an alternative tool in using a commercial linear programming software which is capable of solving a general transportation problem. The selected software must be able to handle a large scale problem, and it needs an additional effort td formulate the problem and transform a result into the ultimate pit limit solution.

Jan 1, 1992

By A. K. Schellinger

1. In the United States, the industrial application of centrifugal force for separating phase constituents has been confined almost entirely to aqueous systems at room temperature. This paper presents results for experimental tests on the use of centrifugal force for separating the liquid and solid phases in molten nonferrous alloys. 2. The development and use of a small centrifuge for treating molten metals is described. The centrifugal apparatus was, in essence, a 3-inch diameter spinner pot, which revolved, within -a gas -fired furnace, at speeds up to 3,000 r.p.m.

Jan 1, 1953

By Eileen Ashworth

Computer-assisted instruct ion is now being used in areas as diversified as training handicapped children to preflight simulation for airline pilots. This paper reports on two courses that have been developed at SDSM&T on the PLATO system for miner safety training. Advantages of computer-assisted instruct ion for this type of training is discussed. (Figures show examples of actual use.) A discussion will be given on other applications such as maintenance troubleshooting, training of engineers and managers at remote sites and training of local people for working in the mine.

Jan 1, 1983

By S. S. Cole, C. E. Wood, T. L. Joseph

"INTRODUCTION Iron ore containing titanium was first used in blast furnaces over a century ago. It is well known that TiO2 is a slag-forming material that will increase the amount of slag produced by the usual gangue materials, silica and alumina. Increase in the volume of slag due to the presence of TiO2 and a lack of information concerning its effect on the properties of the slag have prevented the general use of titaniferous ore. Also rather com¬mon belief among furnace operators that the bottom of the furnace builds up when ores containing TiO2 are smelted has militated against the use of titaniferous ore. This building up of the hearth has been attributed to the formation of copper-colored crystals of titanium cyanonitride, which have been observed in the salamanders of blast furnaces. Until recently the availability of nontitaniferous iron ore has left little incentive to use ore containing titanium.The presence of vanadium in certain deposits of titaniferous magnetite in New York State has created new interest in problems connected with the use of titanium-bearing ore. It appears that most of the vanadium in this ore can be recovered in pig iron, which can be blown in a converter to produce a slag containing vanadium in amounts suitable for the production of ferrovanadium.The Titanium Division of the National Lead Co. recently erected a largo mill to treat ore from Sanford Hill, in Essex County, New York, about 50 miles west of Port Henry. The ore deposit was acquired from the MacIntyre Iron Co. and is often referred to as Sanford ore. It is one of the largest deposits of Iron-bearing material to be found east of the Lake Superior region and is being mined by open-pit methods."

Jan 1, 1943

By H. C. Miller

"Introduction**The progress of the ""Safety First"" movement in the oil fields of California during the past few years has been remarkably rapid. It has been generally concede by those who have learned to value the life and limbs of their employees, that safety is essential to efficiency and no company that has a high accident rate can be considered an efficient organization. Accidents have a destructive effect on the morale of any body of workers and cause disorganization and delays.The increasing danger to life and limb involved in the drilling for and the production of oil and gas, has become so great that it is clearly evident that everything possible must be done to keep it within the narrowest possible limits.There is a tendency toward carelessness, especially by men who are employed in hazardous occupations. This is brought about by the familiarity of the risk under which they are working and in no industry is this more forcibly exemplified than in the oil fields. Men have performed the same or similar duties for many years and have worked around similar hazards and unprotected machinery until many have can entire disregard for the dangers surrounding then. Very often familiarity with a hazard occasions a contempt for that hazard which only too often results disastrously."

Dec 1, 1923

By J. M. Benson

Metal powder compaction offers unique advantages in the manufacture of net-shape components using techniques such as laser sintering, conventional press and sintering, metal injection moulding, direct rolling, direct forging, and hot isostatic pressing. If the output from the primary metal production process is in powder form, then considerable cost and energy savings can be realized by direct conversion to semi-finished or final shapes. This possibility exists for titanium and possibly also for Ta, Zr, Hf, and Nb metals. However, these attractive benefits are associated with some significant risks. The high surface-to-volume ratio of powder particles coupled with the reactive nature of these metals means that special care must be taken when handling them. Powder explosions are unfortunately still a regular occurrence internationally and these often result in serious injury and loss of life. Even seemingly 'safe' compounds such as sugar, flour, and grain can be extremely hazardous when handled or milled and dust clouds are produced. In addition, exposure to airborne particles can have adverse effects on the human body, especially when particles are inhaled on a regular basis. Furthermore, the medical consequences of these are not fully understood, especially in the case of nanoparticles. The impact is often not observed immediately and debilitating illnesses may emerge only years or decades later. As far as is known, there are no South African guidelines for handling of metal powders. This paper attempts to provide an awareness of the risks associated with metal powders (including those produced indirectly by other metalworking/finishing operations) as well as some guidelines for their safe handling, based on international best practices.

Jan 1, 2012

By Brandt Porter, Lawrence K. Nordell, Alexander Potapor

"Improving comminution efficiencies with better machine geometries and motions, improved nip angles, rock movement control, and voids regulation among rocks are some of the next steps to better machine performance. Recent gains (~30%) using high pressure grinding rolls (HPGRS) and vertical roller mills, in theory and practice, are based on Prof. Klaus Schönert’s academic studies (1979–1996) on rock breakage physics. More recently, University of British Columbia Prof. Bern Klein’s studies (2006–present) via the Ph.D. thesis of Z. Davaanyam (2015) further validate theory with practice from laboratory measurements used in this paper.They demonstrated ideal rock compression breakage, within HPGR and vertical roller mill machines using a piston-die apparatus. Similar rock size range is used. The piston-die confine rock breakage behavior. However, these studies do not extend to larger rocks (> 75 mm), and do not demonstrate the influence of rock voids among bifurcation of rocks during comminution. Further, machines fed with larger rock sizes, such as gyratory, jaw, and cone crushers, are not designed or evaluated for geometry nip angle efficiency.Herein we illustrate a performance gain of a new comminution machine, the conjugate anvil-hammer mill (CAHM), first presented at SAG 2011 (Nordell, 2012). The CAHM machine digests rock sizes 400% larger than HPGR, improves rock grip/nip geometry, better improves rock voids, improves surface wear life > 500%, and improves rock containment and slippage during compression. In all, the CAHM machine shows 22 potential improvements over the HPGR. Most importantly, CAHM shows a 50% kWh/ton improvement compared to the HPGR. Our studies use an advanced Discrete Element Method (DEM) computer program called ROCKY. ROCKY simulates moving boundaries, surface wear mechanics, and incorporates rock breakage physics based on the fundamentals of JKMRC T10 protocol [×] with tuned A × b breakage parameters.We calibrate rock breakage in our DEM code to mimicking both UBC laboratory piston-die and HPGR comminution measurements. We then model CAHM with these known ore and machine properties. Differences are illustrated using DEM techniques on each machine, including key points of when each: use geometry; initiate bifurcation breakage; provide a map of particle size distribution by location; illustrate the importance of controlling voids to minimize agglomeration after breakage; machine performance limits; and kWh/ton benefit."

Jan 1, 2016

By Albert Sauveur

THE senior author of this paper has expressed the belief that when gamma iron transforms into alpha iron on reaching the A3 point, each gamma grain does not change bodily into one or more alpha grains but that the alpha phase forms first at the boundaries and along the crystallographic planes of the austenite grains.1 To quote: On cooling through the point A, at about 900° C., iron passes from the gamma condition to a. new allotropic form generally designated as alpha. This transforma¬tion, however, is not instantaneous. There are good reasons for believing that it begins at the grain boundaries and along the octahedral planes of the crystals and that it progresses until each grain of gamma iron is changed into a grain of alpha iron, the resulting structure being similar to that of gamma iron. Were it possible to retain at room temperature pure iron but partially transformed, it seems probable that a Widmanstättian structure, or rather, as later explained, a martensitic structure would be observed (Fig. 1), consisting of alpha iron at the boundaries and at the octahedral planes, and of a groundmass of gamma iron. In order to confirm, if possible, the accuracy of that view, a number of experiments were conducted. Polished samples of electrolytic iron were heated in a vacuum, maintained in the gamma range for several hours and quenched in different media. It was hoped by such means to produce and retain on the polished surfaces a pattern which would reveal the mechanism of the allotropic transformation. The samples were placed in evacuated quartz tubes, heated to 1000° C. and held 2 hr. at that temperature. The tubes were then immersed in the quenching bath. Iced brine and liquid air were used first. The polyhedral austenitic structure existing at the time of immersion was very clearly revealed (Fig. 2). This is generally ascribed to iron volatilizing at the grain boundaries.

Jan 1, 1929

By Read T. A

THE Broken Hill South Ltd. is one of ten companies operating on the Broken Hill lode (See Fig. 1). It has two leases-Blocks 7 and 8-of a total length of 2250 ft. on strike of lode.From the surface to 425-ft. level the ore was found principally in the form of carbonates and high-grade friable sulphides. Below the 425-ft. level the ore is found in the form of compact sulphides. The ore-bodies found in the South mine may be broadly divided into two classes...

Jan 1, 1921