Search Documents

By Y. Guglielmi, C. Gout, P. Henry, P. Dick

The key questions about fault reactivation in shales concern the potential enhanced fluid displacement through a previously low-permeability aseismic shale formation. Here we selected a critically-stressed fault cross-cutting the underground research facility of Tournemire (France) which is located in Toarcian shales. Several inclined boreholes were drilled across the 8.5 m thick fault zone characterized by a fractured damage zone (FDZ) and a central 2.4 m thick complex core (FC) made of multiple shear bands with gouge intercalated with highly fractured lenses. The fault was pressurized using a straddle packer system defining a 2.4m long injection chamber normal to the fault surface. Three fault zone intervals were tested, two in the fault damage zone and one in the fault core. A three-dimensional displacement sensor set in the chamber allowed continuous synchronous coupled monitoring of fault movements, injection pressure and flow rate. An anticlockwise 0.22-to-0.05 mm fault slip was captured associated with a 10-to-100 hydraulic aperture increase of the fault. Preliminary analyses of the experiments show that leakage in the fault zone is controlled by strength and stress magnitude contrasts between the fault core and the fault damage zone. Fault damage zone discontinuities display a much higher peak static friction angle than the fault core shear zones, respectively of 34 and 22° that could be related to complex interactions between healing and sealing processes. Fault core leakage is much more dependent on strain than on effective stress variations. Discontinuous, pulse-like leakage, develops following complex failure processes that may simultaneously take place in the gouge zones and along the large pre-existing discontinuities. Such results may be of importance in evaluating fault seal integrity in oil and gas exploration, production or CO2 storage or underground excavations monitoring.

Jan 1, 2015

By A. G. Darnley

"IntroductionTHE PURPOSE of this paper is twofold. Firstly, to drawn attention to recommendations which have been accepted by the International Atomic Energy Agency concerning radiometric reporting methods and calibration in uranium exploration, and secondly to emphasize the benefits that- will stem from adopting them. These recommendations are contained in an IAEA Technical Report, No. 174, which has been prepared with the intention of serving as a general guide to the subject. The existence of this specialized report is likely to be unknown to most of those who can benefit unless it is given some publicity by an organization such as the CIM. The recommendations were prepared by a small international committee consisting of Dr, P. H. Dodd , U.S .A. , Dr. R. L. Grasty. Canada, Dr. L. Levborg, Denmark, Dr. M. Matolin, Czechoslovakia , Dr. S. D. Simov, Bulgaria, and the writer.The fact that there are standard scientific units of mass, distance and time is taken for granted, It is also accepted that the type of instrumentation used to measure one of these parameters is irrelevant to the way the measurement is reported. Geophysical parameters such as magnetic field strength and gravity have generally accepted units, the gamma and milligal, which are defined in SI terms. These units are employed irrespective of the operating principle, or manufacturer or organization involved in the measurement."

Jan 1, 1977

By C. J. Roos

Ground-engaging tools are used to prevent damage to the main components of earth-moving equipment. These tools consist of everything from shovel teeth to replaceable drill bits to dozer wear plates. The costs of these "consumable" items are increasing with the costs of raw materials. This project developed a tool to be used by Newmont Mining Corp. to predict the consumption of excavator teeth at a particular mine site. This paper presents the results of the Montana Tech research project in which an equation was developed to predict excavator teeth consumption based on production rates and rock properties.

Jan 1, 2010

By D Head

IonicRE acknowledges within our mining industry, there is a common belief that workplace health and safety, often referred to as safety, is just a matter of ‘common sense’ – something obvious and easy. However, at IonicRE, we hold a different perspective. We understand that safety is far from easy. We recognise the need to emphasise the importance of understanding and conveying the inherent difficulties of working safely. We are committed to implementing processes that support individuals in achieving our safety objective of eliminating fatalities and permanently disabling injuries. To build resilience and sustainability into safety performance, we draw parallels with the principles underpinning sustainable and exceptional production performance. Achieving sustainable safety performance demands effective leadership, meticulous planning, adept management, genuine care and unwavering commitment. We’ve leveraged various tools and techniques, such as DISC theory, Maslow’s hierarchy, process control, Kaizen, Six Sigma and Kirkpatrick’s 4 levels, among others, to facilitate this improvement. There methods play a pivotal role in developing a Safety Blueprint for enhanced safety performance. This paper provides an overview of IonicRE’s Safety Blueprint, a strategic framework for developing our safety capability. Our capability is underpinned by three key pillars. Firstly, a comprehensive risk management approach is imperative, encompassing the understanding of hazards, the identification of threats to our people and the associated risks. Secondly, it entails providing and enforcing accountability to sustain our safety capability. Lastly, it involves constructing an effective defence system against threats and harm. Implementing these pillars requires a meticulously devised change process. Anticipating resistance and potential setbacks, we underscore the importance of having the right people and a wellcommunicated vision for safety at IonicRE. A Safety Blueprint serves as a detailed plan outlining the path toward a future goal. At IonicRE, we contend that safety in the mining industry has generally lacked a coherent and effective Safety Blueprint – a comprehensive plan to navigate the journey toward a destination. Drawing parallels with NASA’s detailed plan for landing a man on the moon safely, we question why, as an industry, we cannot similarly eliminate fatalities. While progress has been made in the last century, we must not wait another 50 years to eradicate fatalities from our industry. Examining Safe Work Australia data from 2008 reveals that 47 per cent of mining fatalities result from vehicle activity and 40 per cent stem from individuals being struck by an object. As of December 7, 2023, seven lives have been lost in the mining industry in Australia this year, indicating a stubborn trend mirroring 2022, with limited improvement over the past 25 years. These incidents are not isolated or unexpected. We understand the hazards and controls, yet fatalities persist. IonicRE considers that the mining industry stands at a critical juncture – do we accept a plateau in mining safety performance, or do we rethink our approach? At IonicRE, we are thoroughly reassessing the hazards that threaten our people, systematically redefining effective risk control measures and establishing a robust framework to hold individuals accountable for the effective implementation of the control measure.

Apr 16, 2024

By Loyslene Rabelo Fernandes, Tom Depover, Dagoberto Brandão Santos, Davi Silva Alves, Kim Verbeken, Lisa Claeys

Os aços inoxidáveis duplex (AID) possuem boas propriedades mecânicas da ferrita com a resistência a corrosão da austenita. São bastante empregados na indústria petroquímica, de papéis e nuclear. Porém, são suscetíveis à fragilização por hidrogênio (H2). Amostras de AID 2205 foram recebidas na condição de recozimento de homogeneização (1100ºC por 300 s e resfriamento em água). Em seguida, foram laminadas a frio e recozidas a 1100ºC por 2 h e a 850ºC por 24 h. Foram então carregadas com H2. Análises de extração por fusão foram aplicadas para quantificar o hidrogênio no aço. Testes de tração in situ com carregamento de H2 simultâneo foram usados para avaliar a fragilização provocado por esse elemento. Completando as análises de H2, foram construídos espectros de dessorção térmica. A microestrutura foi caracterizada por microscopia eletrônica de varredura, difração de elétrons retroespalhados (EBSD), difração de raios-x e microscopia eletrônica de transmissão. Na condição envelhecida o foram identificadas as fases sigma, chi e carboneto. O AID apresentou uma redução de ductilidade considerável, alcançando 5% de alongamento já no estado envelhecido. O carregamento de hidrogênio não alterou essa condição. A extração por fusão revelou um teor de hidrogênio na microestrutura de até 50 wppm para a condição recozida, enquanto para a amostra envelhecida foi de 10 wppm. Apesar da alta fração volumétrica de fases intermetálicas e carregamento com H2, as superfícies de fratura foram caracterizadas como microcavidades e intergranulares.

Oct 16, 2019

By W. D. France, H. l. Burghoff

FABRICATORS of copper and copper alloys have contended with the problems of reconversion during the past year in endeavoring to return to the full-scale production that is demanded of them. The problems have not been easy, for the industry, like so many others, has had to deal with strikes of long duration, and material shortages, particularly in the raw materials, copper, zinc, lead, and tin. Despite all these obstacles, it was possible to gear production to new peacetime records during the latter part of the year. This was made possible not only by the use of multiple shifts of personnel, but also by the improved production equipment, the development of which had been stimulated by wartime necessity. The work of installing new and better equipment is still continuing, and virtually every company is engaged in improving or planning to improve its processes.

Jan 1, 1947

By T. C. Wesson

The need for elemental-analysis information on coal mine dust for use in health and safety research prompted this study by the Bureau of Mines. Neutron-activation and X-ray fluorescent techniques were used to obtain five-element analysis (silicon, aluminum, iron, calcium, and magnesium) on 444 samples from 68 coal mines in 10 States. From these analyses, the average composition of the dust in coal mines was determined. The contribution of the primary dusting material (limestone dust) to the makeup of coal mines was shown. Regional differences in mine-dust composition were indicated.

Jan 1, 1974

By J. G. Kirby

The number of petroleum refineries in the United States continued to decline during 1954, and according to the Bureau of Mines annual survey there were 326 refineries with a total daily throughput capacity of 8,420,630 barrels, as of January 1, 1955. The increase in capacity for the year was 413,733 barrels daily, while the number of refineries declined 11. The capacity of the average refinery to process crude oil increased during 1954 from 23,759 barrels daily to 25,830. Breaking down the crude-oil capacity increase, by refining districts; 32 percent was installed at refin¬eries located in the Texas Gulf Coast district, 25 percent in the East Coast district, and 13 percent in both the Louisiana Gulf Coast and the California districts. The Appalachian No. 1, Texas Inland, and New Mexico refining districts reported declines in capacity during the year. Additional crude-oil capacity under construction, January 1, 1955, totaled 146,800 barrels daily. Included in this total are 4 new refineries, 1 each in California, Minnesota, New Mexico, and Washington. In addition to the' new facilities, equipment producing 1.49,550 barrels daily is being replaced.

Jan 1, 1955

By Z. H. Liu

We experimented with slurry which from one of coal preparation plant in Guizhou province and made researches on double hump gradation, one of critical factor of gradation technology, which can influence pulping character in the process of making coal water mixture (CWM). The purpose for it is to find the best particle gradation which can meet the requirements in concentration, viscosity, and stability for CWM. The final result is that the concentration, viscosity, stability of CWM can meet the requirement for industrial use while the rate of fine particle in the slurry is 70%~75% and the maximum concentration of 62%.

Jan 1, 2014

By S. R. Zimmerley

[In the course of a flotation investi£ation, a siliceous gold ore was ground in a'ball mill to ':1inns 300-meeh. It wa. found that the small amotIDt of _Ius 300-mesh material had a gole.. assay approximately twice that of the oriGinal ore, &~d that this overs.ize nroduct also contained much abrac..ed iron. .,Joreove I the gold assay of the abraded iron t which was !1epnrated ma§metically', ~iVFl.£ eight ti;nes that of the are. These facts suggested that some r31aticnship ex?...,ted between the abnorma11y high gold content an the prese:1ce of brA-cit)" iron. It was decided, therefore, to investigate furt~er th~ Fl.Gsociation of the bold ~ith the iron abraded from the balls during sri~Qing ]

Jan 1, 1937

By M Dietrich

The paper describes an efficient method for analysing the different attachment kinematics of excavators and other linkages by taking into account digging forces, the workspace and the stability of the machines. The different attachment kinematic systems of hydraulic excavators and a æclassical analysing methodÆ will be presented. The method was integrated as a plug-in for the multibody simulation (MBS) software MSC.ADAMS to create an easy to use solution for design engineers. A comparison of the new MBS-solution with the classical static analysis is a part of this paper and shows the advantages of the new method. This takes into account the manifold and new dynamic analysing opportunities, as well as more detailed models leading to more accurate results.

Sep 26, 2011

By Jerry Dolph

In September 1855, 55-year-old Noah Spencer Kellogg and his $3 jackass named Bill discovered what was known at the time as a “blow out” of high-grade lead and silver ore. The deposit was located on the side of a North Idaho mountain high above the South Fork of the Coeur d’Alene River. The ore was later assayed at 41,141 g/t (1,200 oz/st) silver. Kellogg named his discovery the Bunker Hill Lode, after the June 17, 1775 Revolutionary War battle of Bunker Hill. A thriving pioneer settlement sprang into existence around the resulting mine’s workings and was eventually— and appropriately — named Kellogg. The peak rising hundreds of feet above the mine’s adit was named “Jack-ass Peak” after Noah Kellogg’s hairy companion.

Jan 1, 1996

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Cu and Zn-0.12 pct Ti-Cu alloys with various copper additions to 1.25 pct. The alloys were rolled cold and at various hot-rolling temperatures to reductions as high as 92 pct after breakdown rolling. The properties are extremely sensitive to various combinations of composition, rolling temperature, and rolling reduction, Zn-Cu alloys can develop good creep resistance, but they are inferior in that respect to Zn-Ti-Cu alloys. For alloys either with or without the titanium addition, cold-rolling results in recrystallization of the matrix and rejection of copper from solution, causing poor hardness, tensile, and creep properties, but high ductility. Peak tensile strengths develop when the alloys are rolled in the range 320° to 400° F, Best creep resistance for Zn-Cu alloys requires higher rolling temperatures when copper content is increased. Creep resistance is best for Zn-Ti-Cu alloys with about 0.75 to 1.0 pct CU rolled near 480° F. Some copper is soluble in the TiZn15 phase, which forms into "stringers" during rolling. The possible contributions to creep behavior of factors such as distribution of second-phase particles, grain size, and preferred orientation are discussed.

Jan 1, 1970

By William W. Adams

A larger measure of safety attended the operation of the stone quarries and related plants in the United States during the calendar year 1935 than in any other year for which annual records are available for the industry. The accident rate, covering fatalities and nonfatal injuries that disabled an employee beyond the remainder of the day on which the accident occurred, was 38.19 per million man-hours of work performed. The nearest approach to this favorable record was in 1932 when the rate was 38.48. The rate for 1934 was 41.82; hence the record for 1935 was 9 percent better than that for 1934. Reports from operating companies showed that 51 men were killed by accidents in 1935 and 4,152 men were injured. (See table 37.) The industry employed 73,005 men and performed 110,033,341 man-hours of labor, an average of 1,507 hours of work per man. Measured in man-days, the total volume of labor was 14,623,303, or an average of 200 days of 7.52 hours per day for each man employed. These figures are not strictly comparable with similar figures for the preceding year, as the, coverage of the industry was more complete for 1935 than for 1934 because special facilities were available to the Bureau of Mines for conducting the 1935 canvass that were not available for the 1934 canvass. Reports covering identical plants that were active both in 1934 and 1935 indicate a reduction of about 7 percent in the number of men employed in 1935. This fact suggests that the apparent increase in the number of workers in 1935 is attributable chiefly, if not entirely, to the more complete coverage of operating plants in 1935. The plants from which this inference is drawn employed 21,799 men in 1934 compared with 20,248 in 1935.

Jan 1, 1937

By Zay Jeffries

IT HAS been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat and cooling either rapidly or slowly with nearly pure iron and slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point, which is near 700° C. The present paper will not consider these old and well-known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, in 1886, reports that both working steel and heat treatment of steel in the blue-heat range are highly injurious. Recently, however, some metallurgists believe that the straightening of warped steel forgings at a blue heat produces a beneficial effect on the metal.2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes -in Iron and Steel Below the Thermal Critical Range, which has the following personnel: R. R. Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F.C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood: This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 2, 1920

By A. J. Forney

The hot-gas-recycle process, for the hydrogenation of carbon monoxide, was investigated in a 12-inch-diameter reactor. Initially because the distribution of gas was poor, hotspots developed in the catalyst bed. After the velocity profile of the gas flowing through the bed was studied, the method of packing the catalyst was altered. Because this change improved the distribution of gas, temperature control was excellent. The l2-inch-diameter reactor was operated successfully in the synthesis of gaseous and liquid fuels. When high-Btu gas was synthesized in two stages, parallel-plate assemblies of Raney nickel were almost as active as granular Raney nickel in the second reactor. The pressure drop through the second reactor, however, was reduced 90 percent by the use of these assemblies.

Jan 1, 1962

By J. Zegarra

"Si bien el anhidrido sulfuroso es considerado como un contaminante atmosférico, puede ser utilizado en la concentración de minerales por flotación a través del reemplazo del NaCN/CaO. En ese sentido, el presente texto señala la aplicación de este reactivo en el proceso de flotación, así también como se presenta los trabajos realizados a escala de laboratorio con el objeto de determinar su aplicación a la flotación selectiva directa de mineralessulfurados y en el mejoramiento del grado de concentrados de zinc. "

Jul 1, 1976

By Alfred Bellows

The objective of this contract is to design, build and demonstrate a support system to improve roof control in the entries of longwall mines. The objective of this phase has been the detailed design of such a system and the selection of a test site in which to perform the pilot demonstration. The result is a complete set of detail drawings or specifications which define the three major components of the system. The Gate Support is a variation of a face chock which has an extended canopy and additional hydraulic legs to protect the region of the face-entry intersection. The Entry Support is a steel beam and hydraulic prop set which is reusable and serves to support the first 100 or more feet of entry inby the longwall face. The Transporter is a bolter-like vehicle with a crane used for installing and retreating the beam sets. The test site selected is CF&I's Allen Mine in Colorado. They presently use simi¬lar steel beams and expect the FMA support system to be more effective as well as recoverable. It is recommended that the completed drawings be used to build a prototype system and test it first in a remote section of the mine and then in the active longwall tail entry.

Jan 1, 1978

By Open-Hearth Steel

We have a very high-powered organization up here this morning, headed by Kenneth C. McCutcheon, general superintendent of the Ashland Division of the American Rolling Mill Company, and L. A. Lambing, superintendent of the open-hearth and Bessemer departments of Jones & Laughlin Steel .corporation of Aliquippa, Pa., representing the open-hearth men. Also, we have P. F. Dolan, assistant general manager of the Maryland plant of Bethlehem Steel Company, of Sparrows Point, and Harry E. McDonnell, superintendent of blast furnaces of Weirton Steel Company of Weirton, W. Va., representing the blast-furnace section.

Jan 1, 1940

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. While the recovery of most copper sulfide minerals is principally liberation controlled, the recovery of molybdenite is much more complex, with fully liberated particles commonly lost to tailings.A geometallurgical investigation was undertaken of molybdenite from the Bingham Canyon deposit with the aim of determining what effects, if any, mineralogy and the mineralogical attributes of morphology, angularity, liberation and size have on molybdenite recovery in the processing circuit. A set of samples was collected from the ores and products of Rio Tinto Kennecott’s Copperton Concentrator. The samples were analyzed by normal polarized reflected light microscopy, X-ray diffractometry, and scanning electron microscopy using a Mineral Liberation Analyzer, revealing the presence of two distinct types of molybdenite, which are the two polytypes: hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins located in the core of the deposit, while the 3R polytype occurs as disseminated, ball-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Each polytype exhibited metallurgical properties consistent with those reported in the literature. The 2H polytype is easily ground, kinetically “faster” floating and displays surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high-quality molybdenum concentrate under normal operating conditions at most copper concentration operations. The 3R polytype is difficult to grind, kinetically “slower” floating and displays surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to operating parameters may be necessary to improve the recovery of molybdenite.A preliminary investigation into the metal budget of porphyry copper and molybdenum deposits indicated a possible positive correlation between total economic metal budget and polytype content. Higher concentrations of the 3R polytype appear to be more prevalent in gold-enriched porphyries than in molybdenum-enriched porphyries. This may help explain why it is easier to obtain higher rates of recovery in molybdenum ± tungsten-rich deposits, which contain little to none of the 3R polytype. There is a potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present as well as its impact on the economics, in terms of exploration, and the processing circuit, in terms of plant design."

Jan 1, 2016