Search Documents

By Q. Chen, J. H. Zhang, M. Zhang, F. M. Zheng, Y. J. Zhang

The characteristics of air bubbles and gas dispersion in KYF flotation cell are studied using the method of the point conductivity probe and CFD simulation. With increasing of speed, the velocities of air bubbles increase slowly and the distribution of diameters exhibits little change. With increasing of aeration rate, the gas holdup is increased. However, the velocities and diameters of bubbles have no great change. The CFD predictions on gas holdup have good agreement with the experiment results. The gas holdup distribution in the center section is revealed. The gas dispersion in the middle and upper part of flotation cell is uniform. It would be helpful for bubbles and solid particles collision. The gas holdup of the lower part of flotation cell is scarce, and it agrees with the observation in experiment. The gas would accumulate at the suction side of impeller blades, and it would decrease the power consumption. The rotating speed and aeration rate have great effect on gas dispersion. With increasing of aeration rate, the gas holdup of flotation cell will increase. The increasing of speed would improve gas dispersion. The results are expected to help to optimize the performances of KYF flotation cell.

Jan 1, 2015

By D. I. Bleiwas

The Bureau of Mines determined the costs associated with lithium production (in various products) from demonstrated resources in seven market economy countries (MEC's). This analysis evaluated the relative economic and resource position of 16 mines or deposits, including 6 producers and 1 (Bernic Lake) operating at pilot scale. The demonstrated resource of recoverable lithium within the deposits studied is approximately 2.2 million metric tons (mt). Virtually all known MEC resources and production were covered, including resources in Chile (59 pct of the total), the United States (13 pct), Australia (11 pct), Canada (10 pct), and Bolivia, Zaire, and Zimbabwe (combined 7 pct). In addition, the large potential of lithium-enriched brines is assessed, especially those in the Atacama Basin, Chile, where production began in 1984. The lithium resource consists of lithium in spodumene, brines, and to a small extent lepidolite and petalite. Most MEC lithium trade originates from the United States, though development of brine deposits in Chile, and potential development in Bolivia, could threaten the U.S. position. Economic analysis indicated that all lithium being recovered from producing properties could be produced at less than the published market price, and that MEC resources from these properties are adequate to supply any foreseeable demand.

Jan 1, 1986

This NIOSH Toolbox Training program contains 52 different modules designed to stimulate safety discussions among your employees. Each module is intended to be completed in roughly 10 or 15 minutes, so a Toolbox Training session can be conducted once a week for the entire year. Each session counts toward your employee’s 8-hour annual MSHA refresher training, thus saving an entire day of work.. The modules are used to refresh employees on the procedures, policies, and practices of working safely at a specific mine site and can easily be tailored to fit conditions and situations found on your property. Every module follows the same format, so that as the weeks pass, miners will start to approach every safety situation in the same way. A typical Toolbox Training session contains five basic steps that cover all the information in the module. 1. Identification of the hazard and discussions about the types of injuries typically associated with the hazard. 2. Discussions of some of the causes of the hazard. The MSHA example included with each module should be referenced. 3. After the hazard and accident has been explained and understood, discussions about best practices and tips for avoiding a similar accident. 4. Review of similar conditions or near misses from your mine site using the leading questions on the form to start a discussion. Specific examples of equipment or structures on the site that could lead to the same accident should be discussed. The blank space on the module is used to add your own remarks and questions to supplement the given information. 5. Miners fill out the training record on the back of the form with name, initials, and date of training session. The modules are designed to be kept in a standard three-ring binder and easily photocopied. This way, the same set of modules can be used for years to come. A blank form is included that can be used to create more Toolbox Training modules. The key component of Toolbox Training is to start a discussion among employees that will allow them to see the hazards around them every day and respond to these hazards in a safe and consistent manner. To start a discussion, ask questions that need more than a one-word response. Get the miners to talk about similar situations from their own experiences and give suggestions about how to fix the hazards around them. Toolbox Training is a quick and effective way to cover specific mining hazards, but it only works if miners are involved in the discussion.

Jan 1, 2004

By Sam McNary

The U.S. Bureau of Mines used the East Fork Pine Creek watershed to conduct a pilot study for an inactive and abandoned mine lands inventory, during which techniques and methodologies would be developed for subsequent inventories. A total of 177 waste dump samples, 191 mill tailings samples, and 36 stream sediment samples were collected. Water samples were collected from 18 sample sites during five sampling events. Waste dump, tailings, and stream sediment samples were analyzed for antimony, arsenic, cadmium, copper, iron, lead, mercury, and zinc. Results indicate a multidisciplinary approach is necessary: disciplines should include geology, geostatistis, geochemistry, geophysics, biology, hydrology, and remote sensing; small prospects do not generally contribute to watershed contamination, major mine and mill sites may contribute metal enriched sediment of metal enriched water; speciation studies and bioavailability studies are important.

Jan 1, 1995

By Runsheng Xu, Haiyang Wang, Pengcheng Zhang, Tengfei Song

Semi coke, a byproduct in the chemical industry, is a new fuel for blast furnace injection in China. In this study, semi coke and bitumite were milled into different size, ranged from 0.147mm to under 0.074mm. The content of volatile matter and ash, which affect the combustibility of semi coke, were measured using muffle furnace. The mixture, in which the proportion of coal in different sizes changed, was blend by semi coke and bitumite with different size. Activation energy calculation and the comprehensive combustion characteristic index of all kinds of blends was also discussed. The result obtained by Thermogravimetry –Derivative Thermogravimetry curves indicates that the smaller the size of mixture is, the lower for the characteristic temperature, and the better for its combustibility, Semi coke can be a substitute for anthracite in blast furnace injection.

Jan 1, 2015

By Sam S. Taylor

"INTRODUCTION This report deals with a comparatively simple application of some of the engineering principles involved in the evaluation, installation, and operation of air- or gas-injection projects and well-clean-out and repair methods to increase the producing rates of oil wells in partly depleted pools during the war. The methods suggested for developing gas-injection projects take into consideration that in general no new wells will be drilled because of wartime restrictions of equipment and manpower and that only existing wells and second-hand machinery will be used. Because air will be employed as the injection medium in secondary-recovery operations where natural gas is scarce and expensive, the disadvantages and hazards accompanying, its use are discussed. Engineering techniques recognized as best modern practice are discussed in relation to the effect of simple air-injection development of properties on postwar operations and Probable ultimate recovery of oil. The report is an introduction to where, when, why, and how an air-injection project should be installed and operated; it is not intended to be an engineering manual for technical guidance in the selection, development, and operation of simulative methods of oil recovery.The report is intended mainly for these thousands of operators in the Appalachian region owning a few wells prodding small quantities or oil daily. Many such operators are anxious to increase their production rates by simulative means and to rehabilitate their wells so that they will produce more oil to help win the war but, in general, are unfamiliar with secondary-recovery operations and cannot afford to hire technical assistance."

Sep 1, 1944

By Charles F. Jackson

Gold mining is a subject that not only appeals to the popular imagination but has vital importance to the world's economic structure. However, a discussion of the use of gold as a medium of exchange, and a basis for credit between nations and for monetary systems is not within the scope of this paper. The importance of gold in carrying on the commerce of the world, the present supply and rate of production, the probable trend of future production, the probable future requirements, and related subjects have recently received much attention from bankers and economists, and many articles on these subjects have been published. During slack periods of base-metal production due to falling prices, accompanied by scaling down of base-metal mining operations and often by the closing down of at least some mines, there usually result revival of interest in gold mining, search for previously undiscovered deposits, and reopening of some old gold mines.

Jan 1, 1932

By F. S. Crawford

The wide variation in the medical facilities, type of accident reports and provision for the welfare of employees, in addition to the compensation provided by the various State laws,- was -studi-eci, by the.. wri-ter in the Lake .. Superior_ r.egion . .. - -Several cDmpanies f~rnished. the information which follows. Names have been omitted , ~ut the information should be of .intere·st to companies desirous of improving t_his branch of thej..r accident-prevention work. : . . --Because a summary of the metho.ds used would merel:y: result in _ a.n a.ttempt to set _up an ideal, it was concluded that in preparing this paper a statem.ent .of_ tbe individual methods of -each company wou-l d .b-e .Qf .. the most inte-res.t, . and the.y h~ve . been .. li.steq with .no regard to the size of the company . . ··· -In the - appendix are -a -number of report. forms used by .various _operators for reporting accidents to t he company and .to the State. These are self- explanatory. and many a re mentioned in -the body of circu-1-ar-.

Mar 1, 1932

By D Kent

"There has been a revolution occurring in underground mining over the last several years, where big headline items such as the Internet of Things (IoT), optimisation, managing data, data mining etc – the list of current catchphrases, goes on. In the end these are nothing new; but the ‘things’ (sensors) are becoming smaller, cheaper and easier to deploy, and the analysis much more powerful as computer processing speeds increase. However, to take advantage of the myriad of devices out there and gain the processing power to analyse and use the data, a reliable ‘conduit’ is needed for that information to be delivered where it can actually be used. That is, a high quality data network.Modern mining is like any other industry in the information age: the access to reliable data is the first, critical step in improving productivity (Stevens, 2015). The convergence of communications onto an IP (Internet Protocol) backbone has been the driving force in enabling the productivity gains in general industry over the last two decades.This paper overviews how this technology has developed as an enabler in accessing productivity and safety benefits, and how it has used access to large amounts of data to manage mining processes underground. Reams of data are useless, but with the reliable receipt, analysis, processing and feedback system in place to use that data, benefits can be realised.Automated mining systems are increasingly being seen as a key requirement for a productive mining operation, and the importance of an integrated communication network infrastructure to support such systems is growing. Another emerging driver is the much talked about IoT and data analytics, both dependant on reliable, accurate, high volume data.The author will outline how communication infrastructure is fundamental to the operation of such systems, and explain why the resultant communication networks require much more than just increased bandwidth (data capacity) to properly support the automation and other data hungry systems within the overall mine operation.Mining operations embarking down this road are discovering that the required network must be based on a true enterprise level architecture to, not only enable the mine’s current plans for remote or automated mining, but also to provide a scalable and integrated platform for future developments. The emerging issues for the communication network to truly support automation systems include: increased complexities of operating and maintaining multiple networks integration issues with disparate systems problems with reporting, particularly as demands for corporate reporting and compatibility with enterprise systems become the norm ongoing management challenges, which will only increase with the proliferation of new technologies.How certain mining operations lay the necessary foundations to meet their current requirements, while supporting their visions for a more automated and proactively managed mine, will be explored.CITATION:Kent, D, 2017. Modern mining – why bandwidth matters, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 123–128 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By Gavin A. Hunt

In order for mines to operate profitably throughout their life it is important to monitor and maximise ore recovery. A common problem facing many mines is the underestimation of clay type and its distribution in ore at the mine face, blast hole or in the ore stockpile. Too much clay entering the heap leach ore stream for example causes a dramatic reduction in heap leach efficacy and or increased leaching times. The end result is poor leaching performance and much reduced metal production. Poor clay identification and quantification is attributable to many factors, including costly and slow off-site mineral analysis techniques, such as XRD, XRF and petrology, the visual and subjective limitations of the core logging geologist and a lack of suitable low cost, high throughput mineral logging instruments. To get round these problems a new, non-contact, imaging spectrometer - the SpecCam - was developed by Spectra-Map Ltd, to allow high throughput identification and quantification of minerals from mineable material. Its novel imaging design can collect millions of data points (pixels) per day; each pixel contains spectral information that allows a wide variety of mineral types, including the smectite and illite clays, and phyllosilicates such as talc and kaolin, to be identified. Because all the ore can be imaged a much more reliable mineral log can be made. Hence, mapping changes in mineral composition - related to variations in phenocrysts, macrocrysts, veining or wall rock - is possible. Examples of SpecCam data from Goldfields Cerro Corona Porphyry stockpile and from Rio Tinto?s Argyle Diamond mine illustrate the mineral identification and quantification capabilities of the SpecCam. More importantly, for the first time very accurate % abundances for the different minerals can be obtained using an image-based modal count technique. The modular design of the camera, plus its extremely flexible high speed filter, mean that the SpecCam can be easily installed on different equipment, each one suited to different ore recovery problems. For example the SpecCam can be used on an automated portable logging frame to measure drill core, RC chips, hand samples or powder, or alternatively installed on a Geotek multi-sensor core logger for high-throughput, automated logging of drill or blast hole core using co-registered multi-sensor data. An exciting recent development has been the installation of the SpecCam on CommoDas ore sorting equipment, used around the world for 24 hour mill-feed monitoring and automatic ore sorting. Real-time ore sorting decisions can be made as material is monitored on a conveyor belt running at 3m s-1, from which the ore can be automatically sorted into high-grade, low-grade or waste streams for example. The three installation options for the SpecCam mean that most mineral analysis and automated core logging or ore monitoring needs can be met at the mine. For the first time rapid and automatic mineral identification and accurate quantification can be made. All of which allow the mine geologist or metallurgist to make important decisions about maximising the metal recovery process.

May 1, 2007

By Fernando O. Boechat

Com a redução da oferta de minério granulado de boa qualidade no mercado mundial e as restrições ambientais à sinterização, as pelotas de minério de ferro passaram a ocupar um papel importante como matéria prima para produção de ferro primário. Entretanto, embora apresentem maior resistência à degradação, as pelotas ainda sofrem com este problema, embora em menor magnitude, quando comparadas com granulados. Pode-se identificar a degradação das pelotas de minério de ferro em duas etapas, durante o manuseio e sob redução. Uma vez que vários estudos já analisaram a degradação durante o manuseio, a degradação durante a redução torna-se um assunto relevante e pouco explorado. Assim, o presente trabalho avaliou as energias envolvidas no movimento da carga ao longo de um forno de redução direta do tipo Midrex, usando o método dos elementos discretos. Para isso, foi utilizado o software EDEM® para obtenção das energias dissipadas durante as colisões das partículas. Aplicando estas energias ao modelo mecanicista proposto por Tavares e Carvalho [4] para fragmentação das partículas foi possível estimar a taxa de geração de finos no interior do forno. Estes resultados foram utilizados na previsão da degradação mecânica de pelotas no interior do forno, que previu a geração de 1,2 a 2,6% de finos gerados em um forno Minimod®, dependendo das premissas usadas.

Aug 1, 2018

By E. Siami-Irdemoosa, S. R. Dindarloo

Ease of excavation or rippability, also called diggability or excavatibility, is a critical decision-making parameter in the selection of both the overburden removal method and the required equipment in surface mining and geotechnical engineering projects. The most widely used method of estimating rippability is rock mass classification. Although there are different classification schemes in the literature, all of them have the two major limitations of sharp transitions at class boundaries and subjective uncertainties in decision making. In this study, the decision trees method was employed as a classification tool for estimating ground rippability, using the four rock mass parameters of weathering degree, uniaxial compressive strength, joint spacing and bedding spacing. The results were compared with those of the widely used method of diggability index rating (DIR) and a fuzzy-based DIR. The problem of subjective uncertainty was resolved in the proposed decision trees method, as the tree rules were derived automatically from the training data sets. Compared with fuzzy-DIR, a decision tree classifier is simpler, needs less computational time and is more appreciable by industry practitioners. Nevertheless, the proposed method is not flawless and, similar to both the conventional and fuzzy DIR methods, yielded poor estimations in particular instances. The limitations of the three methods are discussed.

Jan 1, 2015

The realization that there is a limit to our supply of domestic mineral and fuel resources, which have been taken for granted until recently, has stimulated the need for conservation and optimum utilization of the Nation's minerals, metals, and fuels-resources critical to our national economy. The mission of the Bureau of Mines is to develop new technology, improve existing technology, and disseminate information related to mineral resources and industries. Fulfilling the mission is necessary to insure a continuing, adequate supply of minerals and alternative supplies of energy from reliable sources at the lowest possible cost to society and the environment. Established in 1910, the Bureau of Mines under the Department of the Interior is the Federal Government's primary research arm in the mineral field. Since the transfer of the fossil fuels portion of the energy research program to the newly organized Energy Research and Development Administration (ERDA) in fiscal year 1975, Bureau research has been concentrated on increasing mineral production, decreasing energy usage through more efficient processing, and decreasing material losses caused by corrosion. Concurrently, research is being addressed to improved coal-preparation techniques, especially to expanding utilization of low-grade coals and coals difficult to beneficiate, which are essential for reducing the need for petroleum and natural gas supplies and for redirecting our energy consumption. Fluctuations in the availability of foreign sources of minerals, metals, and fuels due to political and economic variability among nations have necessitated intensified investigation into coal mining, uranium-ore processing, and geothermal energy sources-three alternatives that can help to alleviate the dependence of the United States on foreign sources of energy.

Jan 1, 1975

The Bureau of Mines has reviewed those portions of the "Tariff Schedules of the United States Annotated 1963" that are of interest to the minerals industry. This study shows to what extent rates of duty were altered (increased of decreased), and provides a bridge where possible from the old Schedule A classification system to the new TSUS system of statistical reporting of import data. In general the new tariff has corrected previous classification defects and inconsistencies, but the rates of duties have not been materially changed.

Jan 1, 1965

Jan 1, 1970

By Peter J. Nicholson

The methods of reinforcement to be discussed in this paper are all insitu methods, ones that can be used on the soil structure as it exists in the ground, and do not rely on excavation and replacement of the soil. Current practice in the United States, as well as new ideas and methods, will be discussed as they relate to slope stability, retaining walls, and to other uses such as control of mine or cavity related subsidence and to liquefaction control under existing structures. The method is based on the concept of "nailing" or reinforcing the soil in place, and thereby causing a mass of soil to act as a coherent unit. When performed properly, a true gravity structure can be constructed, one that will remain intact under both horizontal and vertical loadings and that will also resist vibrational and seismic loadings.

Jan 1, 1991

By Harsh Deep Chopra, Jason N. Armstrong, Susan Z. Hua

"Existence of anisotropic Curie temperature materials [E. R. Callen, Phys. Rev. 124, 1373 (1961); J. Appl. Phys. 32 S221 (1961)] is a longstanding prediction - materials that become paramagnetic at a lower temperature along certain crystal directions while remaining magnetically ordered in other directions up to a higher temperature. Validating Callen's theory, we show that all directions within the basal plane of monoclinic F e1Ss (pyrrhotite) single crystal remain ordered up to 603 K while the c-axis becomes paramagnetic at 225 K. Results prompt a re-evaluation of existing magnetic materials with a focus on magnetic characteristics along different crystal orientations above instead of below the ordering temperatures. Theoretical guidelines for identifying new materials with large anisotropy of Curie temperature are also given, and analysis protocol to characterize them in a self-consistent manner is discussed. Materials with such a large directional dependence of Curie temperature open the possibility for uniquely new devices and phenomena, including energy storage and spintronics devices.IntroductionThis paper is an overview of our recently published work on anisotropic Curie temperature materials [l]. As a background, ferromagnetic and ferrimagnetic materials are characterized by a critical temperature below which magnetic interactions prevail over thermal agitation, leading to the appearance of a spontaneous magnetization. Above this critical point, called the Curie temperature, thermal energy eventually overcomes magnetic interactions and the material becomes paramagnetic.It is less well known that the Curie temperature varies with the orientation of the crystal. In ordinary ferromagnets this orientation dependence of Curie temperature is negligible because of the vanishingly small ratio of anisotropy to exchange energy, i.e., the spherical or isotropic exchange term dominates. Thus Curie temperature in ordinary ferromagnets appears to be an isotropic property, and assigning it a single characteristic ordering temperature suffices. However, a 'small' difference is not equivalent to being the 'same', and under appropriate set of conditions the anisotropy of Curie temperature is predicted to become appreciable, as discussed in the following.In formulating the theory of 'anisotropic magnetization' [2, 3] E. R. Callen and H. B. Callen first discussed the ""interesting possibility"" of anisotropic Curie temperature [2] or ACT; Callen and Callen noted that it was W. J. Carr, Jr. who initially raised this question, and they discussed it in detail at the Conference on Magnetism and Magnetic Materials (NY, November 1960), see footnote on page 320 of Ref. [2]. Soon thereafter, E. R. Callen developed the theory underlying the anisotropy of Curie temperature and conditions conducive to its observation [4, 5]."

Jan 1, 2013

By J. Y. Hwang

The relationship between coal characterization and physical cleaning has not been well understood due to the complex nature of coal. Therefore, it is difficult to apply the results of coal characterization to predict and evaluate the performance of a physical separation (e.g. flotation). Eight U.S. bituminous coals were analyzed and studied petrographically in conjunction with washability and flotation tests. The results show that grindability correlates to ash and fixed carbon contents; liberation determined directly by petrographic techniques is close to liberation determined indirectly by washability; and an ideal separation efficiency can be determined by measuring the inertinite content and the washability separation efficiency using a heavy liquid with a density of 1.4. The ideal separation efficiency was attained for most coals by packed column flotation. The ideal separation efficiency can be used for comparing process technologies and process parameters.

Jan 1, 1988

The following is a Maintainability Design Checklist for coal mining equipment. The purpose of the checklist is to provide a summary of design review points for the maintainability assessment of new or existing underground equipment. It specifically focuses on the identification of equipment design features, tasks, or procedures that impact equipment downtime, repair costs, labor hours and maintainer skill level requirements. Some checklist points are general in nature. The checklist was designed to be used across all categories of underground equipment. The intent is to draw attention to design features and maintenance procedures that will increase maintainability requirements. You are encouraged to adapt this checklist to site specific or machine specific requirements by: ? Inserting specific performance criteria for various categories of maintenance tasks. For example; all hydraulic lines on a shuttle car should be replaceable in 15 minutes or 25 minutes, etc. ? Adding or deleting checklist items for different categories of equipment. You would include environmental control equipment, for example, on face equipment and not on shuttle cars or man trips. ? Adding additional checklist items based on site or equipment specific maintenance histories or experience, company maintenance standards, or other factors.

Jan 1, 2000

"Mechanical alloying (MA) synthesizing technology and thennohydrogen processing (THP) were utilized to produce nanocrystalline Ti-MMC's reinforced by TiB intermetallic compound by using TiH2-B powder mixtures. Powders MA'ed up to 8 hours were examined by X-ray diffraction and SEM study. All MA'ed powders afterwards were HIP'ed at 700, 800 and 950EC for 1 hour. Detailed XRD, SEM and TEM study of the samples were carried out to determine the structure and micrography of the Ti-TiB MMC material processed by MA+THP approach followed by HIP'ing at high temperatures.IntroductionThe fiber reinforced titanium base composites [1,2] which possess a great resistance to high temperature have been investigated. In these studies fibers of C and SiC were used as reinforcing materials. However, these fibers react with Ti-matrix at elevated temperature resulting in product formation at the interface between the matrix and the fiber. Because of the chemical reactions, strength of the product MMC material diminishes.In conventional techniques of whisker reinforced composite material production, the mixtures of matrix metal powders and dispersed fibers are consolidated by hot pressing, HIP and/or hot extrusion. These techniques, however, have some shortcomings. Hard and brittle fibers could be broken during mixing cycle of the processing. Consolidation techniques could also be the cause for fiber breakdown. Attaining of the uniform dispersion of fibers into the metal matrix is not an easy process. The chemical reactions at elevated temperature exposures in the interface between the matrix material and fiber reinforcement cause product formations leading to poor mechanical properties."

Jan 1, 1998