Search Documents

By C. P. Mangelsdorf

When the finely bedded shale frequently encountered over coal seams experiences a separation, the material below the separation must behave like a beam or plate in that it must resist both bending and shear. Be-cause of the weakness in interlaminar shear inherent in such strata, shear deflections that are usually ignored in isotropic beam theory may account for a significant part of the total roof sag. Similarly, when a roof truss is installed in such a roof the upward displacement reducing the sag will have components due to shear as well as bending. Questions asked by mine operators about the installation of roof trusses frequently deal with optimum position, slope, and initial tension of the inclined chords. This Bureau of Mines report examines the effects of those chord parameters on the strain energy of both shear and bending and offers optimum values that will minimize the total strain energy of the immediate roof. Design charts are provided, several design examples are included, and the results are compared with current practice. The effects of in situ stresses are investigated and are shown to be equivalent to an additional load on the beam.

Jan 1, 1988

We had a cold, gray winter here in Kansas City and I spent a lot of time watching out my den window at the squirrels and birds trying to get by in the lousy weather. I remember too well working in the cold, loading shots. I was frostbitten several times since I couldn’t tie in MS connectors with gloves on. Those old connectors had a piece of detonating cord on either end of a metal tube that held the delay and you tied them to the trunk lines with square knots. Doing this on a “warm” day in Alaska or Montana shooting ditch for a pipeline could be a frosty experience. Also remember how hard it was to connect up electric caps (detonators to you new guys) in the cold. Now I don’t want you to feel sorry for me ‘cause I suspect most of you younger fellows have also paid your dues in the cold and for that matter in the heat too. Wowee, the heat at the bottom of a Chicago dolomite quarry in August was enough to fry the brains of all that were there. Maybe that’s why the third deck of my brains doesn’t exist.

Jan 1, 2004

By M L. van Kampen

The recent (2005) amendments to the Resource Management Act 1991 have made it clear that there is no obligation on an applicant to consult. However the importance and value in consulting with the community, particularly before commencing a major project, cannot be understated.   This paper looks at the provisions of the Resource Management Act as they relate to consultation and public participation in the process, and will discuss the benefits of consultation both before an application is filed and following the filing of the application. Engaging with the local community can help shape a project to better fit the community, engender support and address opposition. In short, taking the extra step to what is legally required, can help smooth what is potentially a bumpy road. Examples in practice of the value of consultation are given.

Jan 1, 2006

Termination of membership In accordance with By-Law 7.6.1. of the Constitution of the Institute, the names of the undermentioned members have been removed from the membership register. Colloquium and General Meeting A General Meeting and Colloquium on 'Heavy-medium separation and ore sorting' was held on 18th September, 1974, at 09h15, in Kelvin House, Johannesburg.

Jan 12, 1975

By Joachim J. Hauser

Experiments on latent hardening were peyformed by compressing single crystals along a direction perpendicular to the tension axis. The slope and length of easy glide in the tension test were found to depend only on prior deformation in the same slip plane. Prior deformation on a different slip plane changes the stress level of the resulting stress-strain curve. The yield points appearing upon reloading after prior extension and unloading were related to the end of easy glide. SEVERAL researchers have studied the latent hardening due to deformation of a crystal by slip on a slip System after prior deformation. These experiments can be divided into those in which the prior deformation was on the same plane as the subsequent and those in which the two deformation processes were in different planes. In the former category are the experiments of Buckley and Entwistle,1 Parker and washburn,2 and Haasen and Kelly.3 The latter case has not been studied systematically; it was the main purpose of this investigation to produce this type of latent hardening and explain the results in terms of the existing theories of work hardening. In general, tension producing slip on a certain slip system can be preceded by tension, transverse compression or longitudinal compression, each with predictable dislocation movement and intersection. The intersection of dislocations can lead to glissile or sessile jogs, Cottrell-Lomer locks and other sessile dislocations. The effect on the stress-strain curve could depend on which combination of the former mechanisms is operating. Haasen and Kelly3 have studied the yield points which occur in aluminum and nickel single crystals upon reloading after prior unloading in a tension experiment. They attributed this effect to the anchoring of dislocations occurring during unloading. As Cottrell and stokes4 have shown that dislocations cutting through the "forest" could only lead to reversible changes, they attributed the anchoring to the formation of sessile dislocations during unloading. However, different kinds of sessile dislocations could be formed during unloading, and it was the purpose of this experiment to determine whether Cottrell-Lomer locks are responsible for the yield effect and for the end of easy glide. The case where a longitudinal compression is followed by tension along the same axis is commonly referred to as a Bauschinger test. This type of effect was studied by Buckley and Entwistle1 on aluminum single crystals and by Parker and washburn2 on zinc single crystals. In such a test, the tension and the compression activate the same slip plane with opposite slip directions. The use of sideways compression in the present experiments permits the activation of different types of slip systems and the study of their effect on the easy glide region and on the transition between the elastic and easy glide region. The theory of seeger5 for the flow stress in fee materials is applied to explain the latent hardening. EXPERTMENTAL PROCEDURE All the single crystals used in this investigation had an axial orientation close to <210>, called the "0.5" orientation. This is the orientation for which the tensile axis is 45 deg from both the slip plane and the slip direction. The single crystals were grown from the melt under a helium atmosphere using milled graphite boats,=at a rate of 8.6 mm per min. The silver used in the experiment was 99.98 pct pure. The single crystals had a square cross section about 0.9 by 0.9 cm and a length of 14 cm. The orientation of the specimen was determined within ±2 deg by the Laue back-reflection method. The specimens were annealed at 940&apos; ± 2°C in a helium atmosphere for 24 hr and then furnace cooled over a period of 7 hr. The specimens were electropolished in a solution of 9 pct KCN in water. The specimens were tested in a soft-type tensile machine (the load is prescribed) up to 3 pct strain. The stress was increased continuously at approximately 30 g per mm2 per min. The strain was measured over a 5 cm gage length with a mechanical extensometer employing an optical lever. The strain and stress were measured with accuracies of i 2 X 10-5 and ± 2 g per mm2, respectively. The remainder of the stress-strain curve up to 20 pct strain was obtained in a hard-type tensile machine (the strain rate is prescribed). The strain and the stress were measured in that machine with an accuracy of ±2 pct. The compression tests were performed in the hard-type machine using accurately machined steel blocks without lubrication. The blocks were used so as to apply a uniform compression over a length of 13 cm. The strains were measured on the hard-type machine and with a micrometer.

Jan 1, 1962

By Tao Long

Recently, the great amount of funds has been invested in the reconstruction of damaged infrastructure and house of subsidence area of coal mine and mine reclamation. This is a benevolent and popular work, which is highly praised. However, because of complicated collapse area problems in China, especially the less integrated control research in the collapse area of metal mine, and the technological weakness, how to effectively control the subsidence area, restore landscape and ecological environment, and utilize the abandoned mine land, are major issue related to the mining area of sustainable development. The research situation about the formation of metal mine collapse area at home and abroad is reviewed, and then the effect of the collapse area on the mine safety and ecological environment, the existing technical problems and development direction are analyzed. Lastly, the technical measures of the collapse area control and cooperative underground mining is put forward.

Oct 1, 2010

Electronic Detonators have made significant strides over the last few years, both in quality of product and performance in different blast applications. The precision and flexibility of the SMARTDET units provides the mines with a powerful means of controlling blast results, giving both cost and productivity improvements. The SMARTDET Electronic Detonator System, robust and easy to use, has been successfully deployed over the last 18 months in improving mine productivity and creating safer working conditions in both quarrying and long-hole stoping. The key to the improvements has been the precision and flexibility of the electronic timing, and the ability of the mine personnel to grasp the concept quickly and use it effectively.

Jan 1, 1999

By B. B. Agrawal

Iron ore fines is an area of concern in India. A possible avenue is to use these fines for sponge ironmaking. Work has been carried out to pelletize these fines with coal and a suitable binder, and cure them in ambient atmosphere to retain in-situ reductant. Pellets were characterized for physical strength and metallisation. Critical factors were granulometry was percentage of coal & binder. In laboratory tests, pellets got metallized faster compared to lump ore. Large-scale trials were conducted in a 12-meter long rotary kiln plant. For 90% metallization, required residence time was only 60 minutes against 240 minutes for lump ore. Coal requirement also decreased. Investigations established the fast reduction nature of pellets. This is due to reduction-reactions occurring simultaneously at many sited within the composite pellets, in addition to the diffusion of reducing gases from the surface of the pellets to its core. The developed process is a value addition in the conventional pelletmaking and is environment-friendly also.

Jan 1, 2006

By Alfred L. Ransome

GOLD output in Alaska in 1950, following a 2-year decline, increased to the highest point since 1942. Tills unexpected gain in production of the Territory&apos;s greatest value commodity was largely responsible for the increase in the over-all value of mineral output in the Territory to $17,852,000 from $15,549,000 in 1949. Although coal continued to rank second to gold in value of output, production was slightly less than the record production of 1949. The mining of platinum continued to be an important factor in the mineral industry, with production of crude platinum metals exceeding that of 1949. The output of lead was three times the 1949 production, and silver gained 46 percent over the previous year&apos;s total. Copper and zinc production-entirely as byproducts from other ores-showed an increase, but remained minor. Production of tin was relatively small, but substantially above the total for 1949.

Jan 1, 1953

By Robert S. Penczak

Red Lake Gold Deposits ? Descriptive Classification (modified from Pirie, 1982) VHR Au -- Volcanic-hosted (vein & wall-rock) replacement Au deposits ~93% of camp production Q-(T) Au -- Quartz-(tourmaline) vein Au deposits ~7% of camp production Quartz-sulphide Au deposits Porphyry-hosted sulphide Au deposits Current & Significant Past Producers Camp Production 21.6 M oz / 672 tonnes Au Other Deposits / Occurrences (Intermittent Exploration

Apr 1, 2005

By C. R. Carpenter

A dynamic gas-mixing system assembled by the Bureau of Mines for the generation of precise gas mixtures from sources of concentrated or pure gases and diluent gases is described. A set of electronic mass flow controllers with maximum flows ranging from 10 to 5,000 ml/min, a so-called Pure Air Generator, and gases in cylinders are used to generate differing gas concentrations. The repeatability of the delivery rate of a flow controller, measured on different days, has a precision of 0.3 pct of the setting. This dynamic gas-mixing system reduces the cylinder inventory and the demurrage charges for special gas mixtures. Gas mixtures that cannot be shipped commercially, such as flammable mixtures of methane in air, can be conveniently prepared by this system. The maximum dilution ratio is 2.5 x 104. Thus, gas mixtures can be made over a wide range of concentrations, from the percent region (by dilution of a pure single-component gas) to fractional parts per million (by dilution of a premixed standard, e.g., a 1,000-ppm mixture). This system is especially useful in determining the response of gas detection devices over the entire range of their measurement. Because the controllers are voltage controlled they lend themselves easily to automated control using computer-based systems.

Jan 1, 1983

By L. K. Weaver

Bureau of Mines investigated the progressive impact that petroleum (crude oil and condensate) operations in the Gulf of Mexico have had on onshore operations and the expected effect of increasing activities in this area on future petroleum supplies from domestic sources. The data analyzed include capital expenditures, number of wells drilled, success ratio for exploratory wells, daily production per completion, annual producing rates, and oil reserves. The report compares offshore and onshore data and ascertains trends in petroleum industry operations. Observed data and trends indicate that in the near future Gulf of Mexico development and production will continue to increase relative to total U.S. petroleum activity. By 1975 annual oil and condensate production from the Gulf of Mexico is expected to be in the range of 750 million bbl to 1,150 million bbl, and account for approximately 20 to 30 pct of the estimated total domestic production.

Jan 1, 1969

By A. S. Watts

The Bureau of Mines has been conducting an investigation of the feldspar resources of the New England and North Appalachian States with a view to greater efficiency and economy in their utilization. Such an investigation was deemed necessary, not only because of the continued and increasing consumption of these minerals, but especially because of the demand for better technical control of the raw materials that are used by the white-ware industries of the United States. Most manufacturers of white pottery wares have only a limited knowledge of the origin, mode of occurrence, and methods of mining and preparation of the materials that they use. Heretofore, owing to a belief that the supply of raw material was unlimited, the manufacturer had concerned himself chiefly with the solution of the problems of manufacture. Within the past few years, however, it has been found that difficulties arise in manufacture which can be traced beyond the manufacturing process and are believed to be due to a need of better control of the materials used. Furthermore, as competition becomes more severe, more attention must be paid to selection of materials in order to minimize consumption and also to avoid unnecessary expense for transportation of material. Doubtless the lack of interest as regards these details has arisen from the fact that in the past a considerable proportion of the whiteware ingredients has been imported and the manufacturer has been forced to rely on the samples submitted and the general uniformity of the source of supply to insure against variation of the material. An extra precaution arising from this lack of definite knowledge still prevails in the common practice of never depending on one source of supply for anyone ingredient. Often the products of three or more producers are blended so that if anyone shall vary without warning the variation arising from its use will not be sufficient to ruin the ware.

Jan 1, 1916

By John Sasadi

The mining industry depends upon inexpensive water transportation. Today, large quantities of mined products are transported by ships over oceans, from continents to continents, over lakes and waterways to the ultimate users. Sometimes, the routes these Bulk Carriers travel cover only a few hundred miles, sometimes thousands of miles halfway around the world. Most of the products of the mining industries are relatively inexpensive. A significant portion of their cost to the ultimate users are in the cost of transportation and not in loading and unloading these commodities at the ports of origination or destination. So far, the industry has produced very efficient loading and un- loading installations, but has very little influence over marine transportation or the design of the vessels themselves. Very little was ever published dealing with integrated transportation systems properly correlating all phases of the operation; namely, loading, marine transportation and unloading bulk materials.

Jan 1, 1967

By W. W. Edgerton

Construction projects may be delivered under one contract package or multiple packages divided by discipline, geographic location, or other characteristics. Dividing the construction into contract bid packages is called contract packaging, and is a vital and strategic aspect of effectively delivering tunneling projects. The process of contract packaging considers many factors, including the type of project, location, and owner?s priorities. This paper describes the key facets of the contract packaging process used recently on several tunnel projects, reports, where possible, on the success of the process, and concludes with recommendations for applying this process to achieve the right contract package.

Jan 1, 2008

By Fred D. Wright, Stefan H. Boshkov

12.1-BASIC AND PARAMETRIC CRITERIA IN THE SELECTION, DESIGN AND DEVELOPMENT OF UNDERGROUND MINING SYSTEMS STEFAN H. BOSHKOV AND FRED D. WRIGHT The criteria governing the selection of an underground mining system relate to several factors the importance of which varies with geographic location, the state of development of the industrial technology, the economic climate in the Nation and, perhaps, in the world-all these as functions of time. Thus, the best choice of a mining method depends upon sets of definable and undefinable values for numerous factors that may be considered fixed at the precise point in time. Subsequent changes in economic and/or technological developments may necessitate modification or complete revision of the existing mining system. A classification of criteria for selecting a mining system must be based on the broadest definitions. Specific cases may present simple solutions or pose very intricate questions, the answers to which are frequently based on judgment rather than explicit logically reasoned and derived results. Specific criteria may be of negligible consequence in some instances and of overriding importance in other cases. It would be foolhardy to attempt to point out, in the limited space available, all possible variations and interplay of factors, as well as to define the setting in which this interplay can take place. The reader is, therefore, referred to the case histories described in the subsequent parts of this section where actual practice will point out the variability of the problems encountered in the selection of a mining method. A popular thesis suggests that the proper approach to selecting the method of mining should be rooted in the inverse solution, whereby the limitations of the various methods in use serve as criteria to eliminate most of these methods from consideration in the specific case. This narrows the ultimate selection to one or perhaps two most appropriate methods. At this stage, a critical comparison analysis will lead to the ultimate choice. Although such a negative approach un¬questionably is valid in discarding obviously inapplicable mining systems from consideration, it falls short in defining the best system, which in practice quite often turns out to be a variation of a textbook standard, or a combination of two or more such standards. Because the deployment of capital and manpower over a long-term commitment closely follows the selection of the mining system, the decision-maker can well afford to spend a great deal of time and effort in evolving the optimum solution for the peculiarities of his specific case. Within the basic engineering tenets of economy and safety to which the design of a mining system must adhere lie numerous factors of constraint which may be grouped, somewhat arbitrarily but for ease of discussion, into several categories. The criteria that enter into the choice of a mining method derive from the following groups of factors: 1. The shape, size and spatial position of the ore deposit.

Jan 1, 1973

By Yi Luo

The efforts to mitigate longwall subsidence influences on various residential and farming structures by many coal mining companies have been successful in the recent years (Luo, et al, 2003). The successes were largely dependent on the accurate subsidence predictions, correct assessments of potential influences, appropriate design and implementation of the mitigation measures. However, such efforts for protecting large industrial structures are still very rare. In this paper, the successful assessment and mitigation of the subsidence influences associated with a very intensive dynamic longwall subsidence process on a large workshop are presented.

Jan 1, 2005

By R. S. Dean

The original flotation reagents were certain oils selected for a combination of properties that occurred fortuitously. It was recognized quite early in the study of flotation mechanism that, in order to function, an oil must have an active group-one that differs from the remainder of the molecule in its affinity for water or the mineral particle. Wark4 gives credit for recognition of this elementary chemical principle to the senior author of this report.5 However, it was soon found that simple hydrocarbons could not be used as flotation reagents and that two of the functions, which were combined in the early flotation oils such as pine and eucalyptus, could be obtained in separate compounds and their relative intensity controlled to advantage. These two functions were called collecting and frothing.

Jan 1, 1944

By Bruce F. Grant

"INTRODUCTION The future of oil production in the part of the Appalachian region included in southwestern Pennsylvania; West Virginia, and southeastern Ohio is directly dependent on the maintenance of existing wells. This report presents an analytical study of the methods used in oil-well reconditioning in this area. The study is part of a research program designed to evaluate those means of stimulating oil production that can effectively and economically maintain present oil-production rates and make it possible to keep existing wells in operation. Well-reconditioning work was curtailed during the war; therefore, an abnormally large number of wells in the Appalachian Region is now in need of repair. Because the lubricant content of Appalachian crude: oils is high and the refined lubricating oils an; particularly suited to use in high speed, high-temperature engines, the demand for these crude oils during the war exceeds, the maximum rate of production obtainable under wartime operating conditions. Increases in operating, expenses, inability to meet war-time reconditioning costs, and inflexible price structures caused the abandonment of an alarming number of wells during the past 4 or 5 years.As a means of increasing regional oil-production rates, new drilling in the older fields for primary production generally is uneconomical because reservoir pressures in most of the fields have virtually been depleted and the production rates of newly drilled wells are small."

Feb 1, 1948

By David D. DiPonio, John DiPonio, Roger Van Omen

The greatest opportunity to attain the most favorable prices for underground construction projects occurs during the competitive bidding period. The Owner, Engineer, and Contractor need to have a thorough understanding of the project’s design concept, how it is going to be built, and what it is going to cost. This paper presents the opinions of three engineering professionals who are well established in their sectors of heavy civil underground public works construction. This paper will outline and summarize the considerations that the three principal contracting parties of Owner, Engineer, and Contractor need to make to obtain good price quotes at the time of bids.

Jan 1, 2005