Search Documents

By Erik Westman

Few studies have been conducted regarding the location, movement, and relative magnitude of the rear abutment of a longwall coal mine. The rear abutment, or the abutment pressure arch in the gob area, is controlled primarily by the quality of pack of the gob; the more compacted the gob is, the larger the stress would be theoretically. While there is no definitive location for the rear abutment, early studies showed that it could be located as far back in the gob as 300 m (1,000 ft). Like the location of the rear abutment, there has been little research conducted and very few answers as to the exact magnitude of the rear abutment load. Due to the fact that the rear abutment has been studied considerably less than the front or side abutment, the need for further studies is evident. From a ground control standpoint, the location and magnitude of a rear abutment could reveal information on the caving process associated with longwall mining, such as when the initial cave could be expected to occur in future panels. Besides the possible importance of the rear abutment from a ground control perspective, evidence related to the longwall rear abutment could be vital from a ventilation standpoint. The peak rear abutment location could serve as an area for harmful gases, such as methane, to accumulate because forcing air through repacked rock is more difficult than through loose rock. The objective of this study is to determine whether passive seismic tomography could image the location, movement, and relative magnitude of the rear abutment as the longwall face retreated, in addition to the forward abutment and gob. The results of a passive seismic imaging study at a western US longwall show evidence for the location, movement, and relative magnitude of a rear abutment. A clear zone of highlystressed strata is shown where the forward abutment is expected and a low-velocity, damaged zone is shown behind the face where the gob is located. These two zones retreat with the face over a three-week period. In addition, the images show a return to stress levels behind the gob that are slightly higher than overburden stress levels, which is presumably the rear abutment. This occurs at a distance behind the face that is approximately the same as the face width for this mine. We can conclude that passive seismic imaging can be used to identify the location, movement, and relative magnitude of the rear abutment of a longwall mine. This conclusion is dependent on the use of appropriate data collection and processing methods. The information provided can benefit the both ground control and ventilation engineers as they strive to improve the safety and efficiency of longwall mines. The knowledge associated with the rear abutment of a longwall could not only help increase production through proper initial planning and reduce down time, but it could also make positive strides in improving the overall safety surrounding a longwall mining operation.

Jan 1, 2012

By Q. G. Reynolds, R. T. Jones

"Residence time distributions are well defined for batch and continuously stirred reactors. However, there exist many smelting furnaces that do not fit either of these classifications. A mathematical description is presented for the case of a furnace that is fed continuously, but where the liquid slag and metallic products are tapped intermittently. The effects of slag and metal tapping intervals and the fraction of liquid retained in the furnace, are shown to have a significant effect on the residence time distribution.INTRODUCTIONThere are some processes in which the time spent by the feed material in a smelting furnace plays a significant role in determining the extent of the reactions between metal and slag and influences the degree of settling of metal droplets from a molten slag.Residence time distributions are well defined for batch and continuously stirred reactors. However, there exist many smelting furnaces that do not fit either of these classifications. Here we will focus on producing a mathematical description for the case of a furnace that is fed continuously, but where the liquid slag and metallic products are tapped intermittently. The effects of slag and metal tapping intervals and the fraction of liquid retained in the furnace, are studied.Previous work (Jones, la Grange and Assis, 1997) has studied the effect of retention time on the degree of cobalt recovery achieved in a slag reduction process. In that work, a method was proposed for the calculation of the mean residence time of the contents of a pilot-plant furnace. That approach is to be extended here for the purposes of providing a more general design or scale-up tool.The maximum allowable depth of molten material in a given furnace is affected by such factors as the desired batch size (or the size of the ladles) and the pressure of the molten material that the tap-hole and surrounding system can withstand. Within these constraints, there might be some scope for choice of taphole position. The effects of this choice need to be understood mathematically."

Jan 1, 2012

By R. Rumpold

The platinum group metals (PGMs) palladium, platinum, and rhodium represent the key materials for automotive exhaust gas treatment. Since there are currently no adequate alternatives, the importance of these metals for the automotive industry is steadily rising. The high value of PGMs in spent catalysts justifies their recycling. The state-of the-art technology is to melt the ceramic carrier and collect the precious fraction in a liquid metal bath. As the feed material has quite high melting points, huge amounts of energy are required for this process. Hydrometallurgical treatments of the spent catalysts offer the possibility to recycle the PGMs with less energy and time demands. Moreover, automotive catalysts contain further valuable materials to improve the exhaust gas treatment. These compounds, like cerium oxide, cannot be recovered in pyrometallurgical processes. This paper deals with a special process that uses hydrometallurgical principles to recycle the valuable metal fraction from spent automotive catalytic converters. Hydrochloric acid in combination with hydrogen peroxide is used as leaching agent. This combination selectively dissolves the PGMs and the cerium, which can be recovered in separate steps. As the leaching solution is regenerated and reused, wastewater generation is minimized. Furthermore, the process residues constitute potential byproducts.

Jan 1, 2012

By Guolin Zheng, Tiejun Chun, Jian Pan, Deqing Zhu, Xianlin Zhou, Dong Chen

"The high temperature oxidizing-chloridizing roasting is one of useful methods to separate nonferrous metals from pyrite cinder and metallurgy slag. However, as one kind of main nonferrous metals in pyrite cinder and metallurgy slag, copper’s chlorination behavior is not demonstrated. In the present study, chlorination behaviors of CuO, Cu2O and CuS at the temperature range of 1025-1175 ? in air by simulating the chloridizing roasting process of pyrite cinder and metallurgy slag have been investigated. It is shown that Cu2O and CuS is much easier to remove, CuO is refractory to remove. In addition, the presence of SiO2 and CaO increases the Cu removal rate from CuO while the presence of SiO2, Al2O3, CaO and MgO decreases the Cu removal rate from Cu2O. Fe3O4 influences the Cu removal rate from CuO and Cu2O positively.IntroductionAs two kinds of significant secondary resources, pyrite cinder and metallurgy slag contain not only abundant iron but also considerable copper, lead, zinc etc. Millions of tons of pyrite cinder and metallurgy slag were discharged from nonferrous metal and chemical industries annually [1, 2] in China. The pyrite cinder and metallurgy slag are formed by roasting of minerals at a high temperature, so the properties of them are distinctly different from the natural iron ores, and the iron in them is closely associated with copper, lead, zinc and other nonferrous metals. High-quality pyrite cinder and metallurgy slag containing high iron and low impurities can hardly be obtained, leading to their low utilization degree [3]. Chlorination is characterized by the high reactivity of chloridion, the high volatility and low melting point of metal chlorides, and the big differences in the formation of metal chloride. Therefore, chlorination is widely applied in extraction metallurgy."

Jan 1, 2012

By Tiejun Chun, Jian Pan, Deqing Zhu, Zhiyong Ruan

"In this paper, the desulfuration of pyrite cinder pellets was carried out. Phase analysis shows that most sulfur of pyrite cinder exists in the form of elementary sulfur. Most sulfur was removed in preheating stage. 81.25% sulfur was removed and the average SO2 concentration of exhaust gas was 1365ppm when the pellets were preheated at 950oC for 9 min. The final product, assaying 62.42wt%Fe and 0.02wt%S content at 96.88% desulfuration was achieved under the conditions of preheating at 950? for 9 min and roasting at 1200? for 15 min, which can be used as the burden for blast furnace.IntroductionPyrite cinder, as a subsidiary product of sulfuric acid production by roasting of pyrite ores, was solid waste in sulfuric acid enterprises. According to the statistics, the annual production of pyrite cinder is about 15 million tons in China. Besides, there is lots of pyrite cinder deposited for many years [1-3]. The pyrite cinder consumed in the cement and other industries as auxiliary additives only accounts for less 30% of its total discharge and the left is stored in waste pond, occupying much land and polluting environment in China [4-5]. Moreover, pyrite cinder contains iron between 30-63% which can be utilized as a cheap raw material for ironmaking by sintering or pelletizing processes, which can not only prevent pollution but also provide cheap raw materials for ironmaking [6-7]. However, compared to traditional iron ore concentrate, pyrite cinder possesses higher sulfur content."

Jan 1, 2012

By George W. MacDonald

ALFRED NOBEL was born at Stockholm on October 21st. 1833, and died on December 10th, 1896. Although Sobrero’s discovery of nitroglycerin dated back to 1847, this explosive was manufactured on a commercial scale for the first time in 1862, by Nobel at a factory which he erected at Heleneborg, near Stockholm. These works were entirely wrecked by an explosion in 1864. In 1865, he erected works, which are still in existence, at Winterviken, near Stockholm. In 1864 Nobel introduced modifications in the manufacture of nitroglycerin which were the subject of a patent (see footnote No. 1), and at the same time, claimed a process for the detonation of nitroglycerin. Nobel states that, up to that time, the method used for the manufacture of nitroglycerin consisted in pouring glycerin, drop by drop, into a mixture of sulphuric acid and nitric acid contained in a refrigerating mixture. In order that the nitroglycerin should not be decomposed, the temperature was not allowed to rise above 0° C.

Jan 1, 2012

By Keith Henderson

An open pit quarry operation in West Central Illinois provided a challenging proposition regarding the removal of a rock wall that once separated two pits, but was now in the middle of the north wall of the combined pit. Their mining plan included the development of a new ramp into the quarry pit in order to lessen the slope and to shorten haul truck cycle time. The task would be to remove a section of rock left behind from mining operations more than 20 years ago that was at or near the bottom of the designed ramp.

Jan 1, 2012

By E. Peek, L. Becze, K. Reading

"Gallium oxide is an important semiconductor material used in optoelectronic devices (flat panel and solar cell) catalysts and sensors. One of the methods to produce ?-Ga2O3 is the so-called hydrothermal route. It is practiced by Neo Gallium Compounds and comprises of two steps: (1) the production of mainly gallium-oxy-hydroxide in a pressure vessel by reacting metallic gallium with water at 200-220 ºC and (2) the calcination of gallium-oxy-hydroxide at 700-750 ºC to convert it into ?-Ga2O3. This paper describes this pressure hydrometallurgy process supported with relevant thermodynamic data and presents the characteristics of the ?-Ga2O3 powder produced for commercial purposes. INTRODUCTIONGallium is a relatively new metal, having been predicted by D. Mendeleev in 1871, discovered by P.E. Lecoq de Boisbaudran in 1875, and first commercially produced in the USA in 1943. Gallium is not rare, being more abundant in the earth crust than antimony, bismuth, molybdenum, silver and tungsten. However, few gallium minerals exist in nature, and the dispersion of gallium within other minerals add to the complexity of its recovery. In practice, gallium is found in dispersed state primarily in bauxites and in some sphalerites, and, to a much smaller extent, in some coals. At present, a very large proportion of the primary gallium in the world is recovered as a by-product of aluminum plants, mostly Bayer plants, where gallium is extracted from a bleed of the Bayer liquor (Roskill, 2011). In 2011, world production of primary gallium was estimated at 200 metric tonnes. In addition, there is a significant contribution of recycling to the overall yearly availability of the metal.Gallium exhibits fairly remarkable properties: it is liquid above 29.76 ºC, can be supercooled, and with its high boiling point (2204 ºC), is the metal with the widest liquid range. Gallium is magnetic, and is an excellent conductor of both heat and electricity. Gallium also displays a marked anisotropic electrical conductivity (Roskill, 2011). All these properties render gallium almost irreplaceable in the semiconductors (GaAs, GaN, GaSb, GaP wafers) and the optoelectronics industry (flat panel, solar cell)."

Jan 1, 2012

By H. Kinilakodi

The authors previously had developed a methodology that combines injury and citation measures into an overall mine safety performance evaluation tool, called the Safe Performance Index (SPI). It can be easily adopted by mine operators to monitor trends in their injury and citation experiences as a risk assessment method. In this paper, six normalized safety measures and the SPI are used to evaluate the risk that existed at mines in the two years preceding the occurrence of a fatality. The percentage of mines is given for which the risk was high or where trends of some of the safety measures indicated moderate risk. In 50% of the mines, this mine safety performance tracking method could have been helpful to the companies, state agency, or MSHA in recognizing and addressing emerging problems with actions that may have been able to prevent high-risk conditions, the fatality, and/or other serious injuries. The approach would have given scrutiny to the risk for mines that encompassed 74% of the fatalities during 2007-2010.

Jan 1, 2012

By S. Dixon

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level. It is situated in a wide east-west valley. Minera Peñasquito, S.A. de C.V., wholly owned subsidiary of Goldcorp Inc. has operated twin SABC-flotation lines since June 2010. Each line is capable of processing 50,000 tonne per day using a SABC grinding circuit followed by flotation to produce lead and zinc concentrates. The addition of a Polysius Polycom HPGR 2417 with dual 3,000 kW drives to reduce the crushed pebbles produced by the SAG mills was planned to increase production to 65,000 tonne per day per line. The production has been limited to 100,000 tpd due to operating issues in the grinding circuit. The operating issue has been the amount of pebbles generated by the SAG mills is significantly less than originally planned. This paper describes the planned installation of a crushed augmented feed to maximize utilization of the HPGR capacity. This coupled with full utilization of the SAG and Ball Mill available energies there is the potential to achieve a 50% total capacity increase from the grinding circuit.

Jan 1, 2012

By J. Engels

CODELCO is considering the implementation of high-density tailings management at the Chuquicamata mine in northern Chile for its long term disposal plan. To achieve this, CODELCO commissioned the design, construction, and operation of a 70 t/d pilot plant, fed by existing tailings. The testing programme was completed in May 2011, and consisted of laboratory rheological and characterization assessments, pipe loop testing, beaching trials, and analyses of deposition behaviour for solid contents ranging from 57?68% (w/w). This paper describes the characteristics of the pilot plant, the testing programme, the beach trial analyses, and the resulting beach profile predictions based on the stream power theory. CODELCO also used other predictive beach slope methods, such as the equilibrium slope concept, which are not discussed in this paper. The final beach profile for design will be selected after an expert analysis of all methods has been completed.

Jan 1, 2012

By Allan Breitenbach

Leaching has been used since the 1600s on unlined ore dumps and since the late 1970s on lined leach pads for the recovery of metals from mined ore, the latter typically called ?heap? leaching and the former ?dump? leaching. Modern day run-of-mine (ROM) or crushed ore heaps are stacked in controlled lifts on lined leach pads and irrigated with a solvent solution (dilute alkaline cyanide for precious meals, dilute sulfuric acid for base metals and uranium). Conventional lined leach pads store process solutions and any storm water, snow melt and cumulative wet season surplus water by gravity flow to external ponds. Impounding valley leach pads (also known as valley fill heaps) differ from conventional leach pads by storing various combinations of process liquid solution and surplus water within internal ponds by using the interstitial pore volume of the ore. While impounding liquids within the heap is simple in concept, impounding leach pads are more complicated for construction and containment compared to conventional leach pads with external ponds.

Jan 1, 2012

By K. M. Murphy, M. B. Wittrup

ABSTRACT The Saskatchewan Ministry of Environment recognizes the importance of environmental protection as an important contributor to Saskatchewan’s economy, with the environmental performance of industry closely monitored. Unfortunately, environmental regulation is often accompanied by significant process that does not always add value to environmental protection activities. The Saskatchewan Ministry of Environment has embarked on a visionary restructuring of its regulatory framework from conventional command and control regulation to a results-based regulatory framework. This new regulatory framework will provide for establishing clear environmental protection and resource management objectives; streamlining the environmental acts and regulations; developing an environmental code of practice; relying on qualified persons; enhancing compliance and enforcement tools; eliminating of many permits; and developing greater certainty in environmental assessment decisions. Results-based regulation promises to deliver enhanced environmental protection with less process. The uranium industry in Saskatchewan will be used as an example of the potential effects of results-based regulation.

Jan 1, 2012

By J. Mothomogolo

Mining projects are capital-intensive and are also characterized by high technical and economic risks. These factors pose challenges to mining entrepreneurs when they seek to raise seed capital for mining start-ups. There are limited sources of mining investment funds in South Africa and each has shortcomings due to one reason or another. Another impediment is South Africa?s status as a developing economy, in which the standards of living ? which in turn influences the savings culture ? the limited GDPs and budget, the socio-political environment, and banking, mining, treasury and other regulations, determine the size of investments, particularly in mining ventures. The proposed funding mechanism was developed with the aim of filling the gaps identified in existing funding mechanisms that were developed by the government with the introduction of the Minerals and Petroleum Resources Development Act (MPRDA), 2002. The shortcomings identified were presented to the study participants as questions to obtain views that were used to define innovative ways of raising mining start-up capital. Most participants in the study supported the derived hypotheses and proposals, and these were used to refine the proposed mechanism for mining investment in South Africa. The proposed funding framework is aimed at encouraging interaction between mining entrepreneurs, government, and the investors to align goals and expectations when undertaking a mining investment.

Jan 1, 2012

By S. J. Lötter

Analysis of the major and minor components of raw zircon as well as plasma-dissociated zircon was undertaken using inductively coupled plasma optical emission spectroscopy (ICP-OES). Microwave-assisted acid extraction as well as flux fusion using lithium tetraborate were investigated as digestion methods. Microwave-assisted acid extraction samples were analysed with matrix-matched standards. The most successful microwave-assisted acid extractions yielded 44.3(1), 49.75(7), 78.3(3) and 90.0(7) per cent recovery for Zr, Hf, Al, and Fe respectively using sulphuric acid. In no instance was acid extraction capable of complete digestion of the sample matrix. A standard addition method was applied to the flux-fusion samples due to the high complexity of the sample matrix. Method validation for the flux fusion procedure was performed using the SARM 62 certified reference material (CRM) with acceptable recovery ranges being based on the 95 per cent confidence intervals of the CRM. Successful analyses were achieved for Zr, Hf, and Ti with apparent content of 66(6), 1.7(1) and 0.15(1) per cent respectively.

Jan 1, 2012

By Enrique Munaretti, Vitor Rosenhaim, Jair Carlos Koppe, Joao Francisco Feijo

The B3 mine is a multiple coal seam strip mining in operation in Rio Grande do Sul, the southernmost state in Brazil. A traditional truck & excavator operation is used to remove the overburden and selectively mine coal seams, ranging in thickness from 30 cm (1 ft) to 2.5 m (8.2 ft). Blasting is required in order to excavate part of the sedimentary rock overburden where the rock is too hard for mechanical excavation, and to mine the coal seams, selectively.

Jan 1, 2012

By T. G. Joseph, A. Chamanara

ABSTRACT: The chicken and egg scenario — where adverse truck motions cause ground deterioration and poor ground profiles cause adverse truck motions — is a downward deterioration spiral dominating our industry. If we remove one action, the reaction stops. A simple truck to excavator load data analysis and wireless communication system is outlined, which will provide visual assistance to the excavator operator in achieving improved load placement and balance in a truck body. This will reduce subsequent hauler duty cycle adverse motions and g levels that contribute to structural fatigue, higher tkph, reduced tire life, and ongoing maintenance of haul roads.

Jan 1, 2012

By J. E. Nesset

"I had been requested earlier this year by MetSoc, our sister society of CIM, to contribute a chapter on technical developments in Canadian mineral processing over the past 50 years to their 50th Anniversary volume. Accepting the challenge of assembling such a chapter seemed at first a reasonably straightforward task, until one realises that the list of contributions by Canadians to mineral processing over this period has been more than just significant. It turns out to have been an extraordinarily fertile time for innovation and impact for Canadian-based technology. The list is necessarily a subjective one, however I had no trouble identifying twenty technology developments that are clearly outstanding, and there are undoubtedly others. As much as possible, I approached the individuals themselves who played key roles in each technology and asked that they tell the “story”. Without exception, all who were invited accepted eagerly and delivered more than I had hoped for. The technologies have been grouped into those that are truly Canadian innovations, such as the Knelson gravity concentrator and the McGill gas dispersion sensors in flotation, and technologies where Canadians and Canada played a very significant role in their success and implementation, such as AG/SAG grinding and ion-beam surface analysis. Also included are what may be termed technology transfer initiatives and institutions that have risen to a world class level, such as SGS Lakefield and the Canadian Mineral Processors Society of CIM. The challenge is now for the coming generation to continue this record of innovation and contribution to the industry, and that includes the (mostly) Canadian mining and metallurgical companies who have taken the longer term view and supported many of these initiatives, through their critical early years, with both financing and project sites for these ideas. Let us hope that the current trend of mining company globalization will not dampen their enthusiasm to participate. This plenary presentation will highlight many of these technologies, the individuals behind them, and their significance to the mineral processing industry."

Jan 1, 2012

By J. Talja

"Non-ferrous metal concentrates contain typically 7 – 12% water when received at the smelter. Removal of this water prior to smelting is always economically feasible because unnecessary heating of vapour (from 100 °C to 1200 °C) in the smelting furnace can thus be eliminated. This results in major reduction in CO2 emission and direct annual savings of several millions of dollars due to improved energy efficiency. Next step to further improve the energy efficiency, to gain substantial savings and simultaneously cut emissions is to select modern technology for the drying process. Consequently, all CO2 emission will be completely eliminated (from 40,000 tpy down to 0 tpy), NOx emission will be negligible, and the SO2 emission will be reduced by over 99 %. Switching of conventional direct heated drying technology to modern indirect steam drying brings, in addition to dramatic emission reduction, additional savings due to further improved energy efficiency. Direct energy savings count for 900 – 1300 MJ/t H2O, which depending on the concentrate feed rate and its moisture load can be worth several millions of dollars every year. Additional savings in operational expenses related to drying and gas cleaning may be worth a few million dollars more. Sustainability is a key issue today, and major savings together with significant emission reduction are readily available by proper technology selection for concentrate drying. INTRODUCTIONSustainability is a decisive principle in any process industry accompanied with emissions and high amount of energy. This is of significant importance in metal processing, including concentrate drying, where minimum impact on the environment, people and community are targeted, and all this with minimum cost, effort and resources. Therefore, special attention is paid to high energy efficiency, low energy consumption with preferable utilization of waste energy, safety issues, availability, level of maintenance, cost of maintenance, and emissions among other things.Non-ferrous metal concentrates can be dried using various techniques. Conventional drying based on direct heating, and use of fossil fuels for drying energy has almost entirely been replaced by steam drying. It is based on indirect heating and it has become the most dominant drying technology for copper concentrates during the last decade with over 90% of the market share of all new dryer installations. Among the steam dryers the Kumera Steam Dryer is the most pre-dominant technology with some 70% of all new dryer installations world-wide."

Jan 1, 2012

"Ore deposits containing rare earth elements normally contain small amounts of the radioactive elements thorium (Th) and/or uranium (U). These are the naturally-occurring isotopes U238, U235, and Th232 (and associated decay-series daughter products) that are ubiquitous in nature, and that contribute a small percentage of the natural background radiation exposure encountered by humans. The presence of these radioactive materials in the ore deposit creates potential hazards to human health and the environment that must be dealt with properly in the mining, processing, and refining of the ores, as well as management of waste streams and residues. This paper presents an overview of the environmental and safety issues associated with U and Th, with particular emphasis on rare earth mining, processing, and refining projects; the regulatory approaches followed to ensure that rare earth deposits are developed, operated, closed, and decommissioned safely; and the development of information during the project predevelopment work and permitting processes that feed into the design, operation, and closure of tailings impoundments and milling/separation/refining facilities. Case studies will be presented subject to the availability of relevant public information. INTRODUCTIONNearly all ore deposits containing economically-recoverable rare earth minerals also contain small amounts of the radioactive isotopes for the elements thorium (Th) and/or uranium (U) and their associated radioactive decay products. Therefore, the handling and management of these materials in mining and mineral processing operations must be performed so that workers and the environment are protected from harm from Th and/or U (and their radioactive decay products), just as they must be protected from any other potentially harmful constituents present in the ore or introduced in processing. Examples of these might include ores with high sulfide content, which may pose a risk of acid rock drainage, or chemicals used in ore processing and metals production.The purpose of this paper is to present information on how rare earth mining and processing projects with ores containing Th and/or U can be developed, operated, and decommissioned safely according to applicable regulations intended to protect worker health & safety and the environment.It should be noted that some countries are considering developing Th as a feedstock for producing nuclear energy, which could have some effect on future development of rare earth ore deposits. To avoid confusion, that issue is not discussed in this paper."

Jan 1, 2012