Search Documents

By J. Trojacek

A large-scale development in exploration and production of uranium ores in the Czech Republic was done in the 2nd half of the 20th century. Many uranium deposits were discovered in the territory of the Czech Republic. Over a period of 50 years approximately, 110 000 tons of uranium in concentrate were produced. Different mining methods were developed and used. One of the most considerable deposits in the Czech Republic is the site Hamr na Jezere ? Straz pod Ralskem where both mining methods ? the underground mining and the acidic in-situ leaching ? were used. The extensive production of uranium led to widespread environmental impacts and contamination of groundwaters. Over the period of ?chemical? leaching of uranium (ca. 32 years), a total of more than 4 million tons of sulphuric acid and other chemicals have been injected into the ground. Most of the products (approximately 99.5 %) of the acids reactions with the rocks are located in the Cenomanian aquifer. The contamination of Cenomanian aquifer covers an area larger than 27 km2. The influenced volume of groundwater is more than 380 million m3. The total amount of dissolved SO4 2- is about 3.6 million tons. Approximately 0.5 % of the contamination is located in the Turonian aquifer. After 1990, a large-scale environmental program was established and the Czech government decided to liquidate the ISL Mine and start the remediation in 1996. The remediation consists of contaminated groundwater pumping, removing of the contaminants and discharging or reinjection of treated water. The objectives of the remedial activities are the followings : to restore the aquifer to a condition guaranteeing continuing usability of Turonian water of Northern Bohemia Cretaceous, to decommission boreholes and surface installations and to incorporate the surface of leaching fields into the ecosystems taking into account regional systems of ecological stability and urban plans. Nowadays four main remedial technological installations for reaching of these aims are used - the ?Station for Acid Solutions Liquidation No. One?, the ?Mother liquor reprocessing? station, the ?Neutralization and Decontamination Station NDS 6? and the ?Neutralization and Decontamination Station NDS 10?. Total capacity of this complex is sufficient to reach the target values of remedial parameters in 2037. The remediation action consists of: pumping of residual solution to the surface, separating uranium from the solution and reprocessing contaminants into commercially usable or ecologically storable products. It is expected that the amount of withdrawn contaminants will vary from 80 000 to 120 000 tons per year. Total costs of all remediation activities are expected to be in excess of 1.5 billion EUR.

Aug 1, 2013

By Zachary Mayer

Agenda ? Kidd Mine ? Background ? Problem & Opportunity ? Challenges associated to depth - Production Rates - Productive Work Time - Operational Delays - Transfer Levels - Mucking Time - Impact on Hoist ? LHD Automation ? Sandvik AutoMine Lite ? Expected Benefits Kidd Mine - Background ? Located in Northern Ontario, Canada ? Underground base metal mine operating since 1966 ? Total 148 Mt mined (2.31% Cu, 6.08% Zn, 75 gpt Ag) ? 2.35 Mt/Y from stopes as deep as 9500 ft (2.9km) below surface ? Mining method: blasthole open stoping ? Mine/Mill: 1263 employees and contractors ? 2012 National John T. Ryan Safety Award

Aug 1, 2013

By K. Ebrahimi-Nasrabadi

The dependence between the extent of conversion of cryptocrystalline magnesite to caustic magnesia was studied experimentally in the temperature range of 400?1200 °C and for calcination times up to 8 h. A TGA?DTA analysis showed that decomposition begins at temperatures as low as 340 °C and is completed at 600 °C. Measurements of specific surface area (SSA), iodine adsorption number (IN), crystallite size, and loss on ignition were carried out to characterize the product quality. It was found that while all the parameters are dependent on the extent of calcination, densification of the product caused by grain coarsening affects their final values. As a consequence, SSA and IN went through a maximum with time. The study showed that high quality caustic calcined magnesia can be produced in a narrow range of temperature (600?650 °C) and time (1?4 h). Medium quality caustic calcined magnesia can be made within a wider range of parameters.

Aug 1, 2013

By Greg Ford

Each year, companies spend millions of dollars on safety training and on safe equipment, money that is generally well spent. Despite that, we still make mistakes. What happens if the mistakes are made not because of inadequate training, but because we are hard-wired to act in a certain way? If you read any of the ?Because of Human Error? text boxes in this document, situations like these may look familiar in your own workplace. ?The issues of risk, health, safety and the environment are getting more attention now than ever before, at all levels of the organization,? said Calvin Price, vice president of Global Health and Safety at LNC-Lavalin Inc., a company with 21,000 workers worldwide. Most would agree with Price that attention to safety is increasing because responsible companies care about their workers and the workers? colleagues, families and communities. However, cynics might say that the safety spotlight is powered by the corporate bottom line. Direct costs created by workplace injuries total $51.8 billion annually and include workers? compensation payments, medical expenses, civil liability damages and litigation expenses. This sum represents a staggering one quarter of each dollar of pretax corporate profits. Indirect costs may run as much as 20 times the direct costs of on-the-job accidents and illnesses. Examples of indirect costs include training replacement employees, investigating the accident and implementing corrective measures, lost productivity, repairing damaged equipment and property, and costs associated with lower employee morale and absenteeism. What?s interesting is that up to 90 percent of incidents are due to human error, not faulty equipment or other factors.

Aug 1, 2013

By T. M. Ruff

A GPS-based traffic awareness and collision avoidance system has been implemented at mines with long, narrow access roads to help avoid accidents involving two approaching vehicles or vehicles following too close. A simple display in the cab of each outfitted vehicle gives an indication of oncoming traffic and a voice announcement indicates the type of vehicle that is coming as far out as 300 meters. Advanced warning of approaching vehicles is increasing driver awareness, especially around blind corners and in adverse weather such as heavy fog, snow, or rain. Speeding alarms have also been implemented and are especially critical as a vehicle approaches reduced speed areas near single-lane bridges or tight curves. A description of the system, safety improvements seen since its introduction, and implementation challenges will be discussed.

Aug 1, 2013

By H. Bouzahzah

Sulfidic tailings, subjected to atmospheric water and oxygen action, can generate acid mine drainage (AMD); which is the most important environmental problem facing the mining industry. AMD generating potential can be assessed by the static tests which consist of a screening method where the neutralization potential (NP) and the acid-generating potential (AP) of a given rock sample are determined. The AP and NP are determined separately in the different static test existing procedures which can be divided into two distinct classes: chemical and the mineralogical methods. For some chemical method, the AP is calculated on the basis of total sulfide sulfur content in the sample which may overestimate its AP if significant quantities of non-sulfide sulfur species are present (e.g. organic S in coals, some sulfate as gypsum, barite, etc.). However, the mineralogical method evaluates the AP by the sum of the individual sulfides participation on acid generation based on their concentration within the sample and can be more accurate than the chemical method. For AP calculation, the Paktunc (1999a) mineralogical static test takes into consideration all sulfide minerals occurring in the sample. However, it does not take into account the rates of acidity production of these sulfides submitted to weathering conditions. So, the present study focusses on the modification of Paktunc AP calculation by considering the acidity production rates of these minerals. To reach this objective, five base-metal sulfides (pyrite as reference, chalcopyrite, sphalerite, arsenopyrite, galena), diluted within quartz (25?75 wt.%) simulating mill tailings were subjected to a kinetic test to evaluate their AP. The results show that all the studied sulfides minerals generate acidity at different rates, so the Paktunc?s equation for AP calculation has been adapted accordingly.

Aug 1, 2013

By A. P. E. Dirige

The stability design of cemented backfills is normally conducted using conventional approaches. Analytical or numerical models, backed by trial-and-error methods, are the primary means used to describe or predict the support performance of backfills during mining. The stability of paste backfill free-standing faces is a major concern due to potential consequences to production, ore dilution and safety. Available analytical or mathematical models are developed based on assumptions of the failure modes that may occur when vertical fill faces are exposed during adjacent mining. Numerical modeling serves to provide an understanding of backfill strength and deformation behaviour. Such approaches offer inherent limitations and generally result in conservative designs. In this paper, centrifuge physical modeling was conducted not only for performance evaluation studies, including stability analysis, but to develop an understanding of the strength and deformation behaviour of paste backfill exposed faces when the adjacent ore zone is removed. The failure mode and mechanics of failure observed in the centrifuge model of a given prototype situation are discussed in detail. Centrifuge model results were compared to numerical modeling and it was concluded that a sliding block failure mechanism that resembles a circular slip appears to be the predominant failure mode.

Aug 1, 2013

By Linlin Zhang

Rare earth elements (REEs) are a group of lanthanides elements which have been widely used in the electronic, petrochemistry, metallurgy, and defense industries. Their demand has increased sharply in the past decade with the boom in electronic device production. Some countries now consider them strategic metals for the future and it has been forecasted that REEs may become a dominant contributor to global economy. In the wake of REE exploration, mining and processing, concern has grown over occupational and community health issues and risks. A portion of available literature on this topic however is written in the Chinese language, and thus research information related to health and REE mining is not readily accessible to mineral development planners in countries such as Canada, where REE mining is now evolving. As REEs also represent an important commodity, primarily stemming from Chinese production, it is important to begin to understand the potential health costs related to this mining sector. There are two main objectives of this paper. The first is to present an overview of REE mining with a focus on geological characteristics, global production and uses with particular attention to the main producer: China. The second is to present the results of a literature review (using both Chinese and English sources) on REE mining and health and identifies key occupational and community health issues that require consideration. This paper concludes by identifying some critical issues this sector needs to address to ensure the sustainable development of this mining activity.

Aug 1, 2013

Pressure for Better Safety Practices ? Increase Government Regulation ? Safety practices evolve from: ? Increased efficiency and performance ? More knowledgeable workforce ? Focus on decreasing risk to shareholder value In Order to achieve this ? Focus Points: ? Skill Development ? Best practices ? Situation-based decision making ? Enablers: ? Adoption of new technologies ? Transformed miner education ? Delivering on-demand information to the point of work Results: Miners empowered to improve mine safety

Aug 1, 2013

By Transfert Environment and Society

Transfert?s added value ? Building bridges between project promoters and communities ? Unique expertise in working toward Social License to Operate through meaningful community engagement ? 25 years of recognized innovation and a systematic approach ? Key mining clients: ? Royal Nickel Corporation ? IAMGOLD - Niobec ? Richmont Mines - Wasamac ? Mine Arnaud ? Managem

Aug 1, 2013

By A. Boeing

Rock-breaker automation and remote operation improves the safety and efficiency of mining operations. This article presents an overview of the Rocklogic rock-breaker automation system architecture that provides collision avoidance, automated parking, and remote operation functionality. The system consists of a distributed computer control system that interfaces with sensors attached to the rock-breaker, the rock-breaker hydraulics, and the site infrastructure. We present results of an automated Transmin rockbreaker installed in a production environment at an underground Australian mine site. The system has been in production use for over 900 days during which there have been no reported collisions, and 100% adoption of the remote operation technology. As a result, Rocklogic has significantly improved the safety of rock-breaking operations and reduced the rock-breaking cycle time, thereby improving the sites overall throughput.

Aug 1, 2013

By Wang Xianzheng

For a long period of time, the Chinese Government has been attaching great importance to and supporting the rapid development of the coal industry. Particularly since more than 30 years ago, when China introduced the Reform and Opening-up policy, the reform and development of the Chinese coal industry has witnessed world-recognized achievements. National coal production increased from 618 million tonnes in 1978 to 3.52 billion tonnes in 2011. While China?s coal production accounts for 49.5% of the world?s total, its annual production growth contributes to over 80% of global production growth. China is a country utilizing coal as its main source of energy. As the Chinese Government gives support to the rapid development of new and renewable energy sources, as well as to increased coal utilization efficiency, the ratio of coal in the primary energy consumption mix will gradually decline. However, for a long period of time to come, the total volume of coal demand will keep rising modestly. The Chinese Government has been highly committed to and actively promoting the overall, coordinated and sustainable development model, which puts people first. It has put forward a strategic task to build an ecological civilization, and highlighted its resolve to uphold the basic national policy of resource conservation and environmental protection, with a view to the pursuit of sustainable development. China will incorporate its response to climate change into the national economic and social development program, and take effective measures to lower CO2 emissions 40?45% per unit of GDP in 2020 compared to 2005. At the same time, China will increase the ratio of non-fossil fuels to 15% in the primary energy consumption mix. All of the above factors have raised requirements for the Chinese coal industry, with implications for clear directions, plans and goals for the development of the coal industry.

Aug 1, 2013

By A. Kowalski

Telvis Limited, manufacturer of an emergency communication dispatcher's broadcasting system, now introduces the possibility of a remote software upgrade to its devices. The paper presents methods, features and ways to accomplish this task. It describes the mechanisms used and the opportunities that arise from the use of this type of functionality. The mechanism software update presented applies to devices on the surface and in underground areas of mines. The electronics used currently allow the use of remote software updates, but the mining equipment makes little use of these methods. This paper aims to start the discussion on this topic and tries to lay the path of development by showing one of the first examples of the application.

Aug 1, 2013

By Franz Xaver Spachtholz

K+S Potash Canada GP (KSPC) is part of the K+S Group, one of the world's leading suppliers of standard and speciality fertilizers and the world?s leading salt producer. Globally, the K+S Group employs more than 14,000 people. The K+S share ? the only commodities stock on the German DAX index ? is listed on all German stock exchanges. Legacy, K+S Group?s most recent project, is a greenfield solution potash mine and production plant in the south of the Canadian province of Saskatchewan. Therefore K+S will invest 4.1 billion CAD. With the expected commissioning in summer 2016 the company projects to reach the two-million-tonnesmark of production capacity at the new location at the end of 2017. The gradual extension of the annual capacity to 2.86 million tonnes of potash products will occur afterwards. The Legacy Project will be Saskatchewan?s first new potash mine in nearly 40 years. It is one of the world?s most economically attractive potash projects. The project will contribute to Saskatchewan?s growth through employment, tax revenues, utilities, and local partnerships. Located in the southern part of Saskatchewan?s potash belt, the deposit is too deep to be mined conventionally due to rock mechanics and high temperatures. Legacy will therefore be a solution mine. Proximity to the urban centers of Regina and Moose Jaw is imperative, with their workforces and economy, as well as access to highways, railway carriers and, most importantly in the prairies, water. With this unique project setting and mining technique, we are convinced that Legacy will be one of the most efficient, economic, sustainable and safe potash facilities in the world.

Aug 1, 2013

By D. L. Cluff

Ventilation Air Methane (VAM) is a high volume low concentration methane source. The capture or use of methane from VAM is challenging, which results in the routine discharge of methane into the atmosphere. Mitigating VAM has the benefits of providing an energy source and reducing the atmospheric Greenhouse Gas (GHG) burden. The GHG radiative forcing effect of methane is 17?23 times as potent as carbon dioxide on a 100-year time horizon. Thus, any reduction in atmospheric methane would be beneficial. The calorific value of methane is 55.5 MJ/Kg; therefore, a 100 m3/s flow with VAM concentrations from 0.1?1% can provide 3.8?38 MW of exploitable power. Strategies to mitigate VAM such as: Thermal Flow Reverse Reactors (TFRR), Catalytic Flow Reverse Reactors (CFRR), Lean Burn and Catalytic Gas Turbines, Biothermica Vamox®, Megtec VOCSIDIZER©, and Vamcat? are briefly reviewed. The review of VAM mitigation technologies reveals disadvantages such as the need to maintain a minimum internal heat capable of oxidizing the methane. This requirement uses all of the available methane up to the point of reaction sustainability and up to half at the highest methane concentration in VAM. Some systems may introduce a pressure drop to the ventilation system, which would impinge on the existing ventilation system design. These impediments necessitate the development of a more amenable technology. In the proposed system, gas turbines (GT), coupled to a combustion chamber with an external fuel supply, assist the combustion of the VAM. The combustion-chamber coupled system provides electricity, while the heat contained in the GT exhaust gases increases the temperature of the VAM, encouraging the development of a flame inside a combustion chamber. The flow from the combustion chamber streams through a primary air/fluid heat exchanger capable of producing steam of a high enough quality to generate electricity using conventional steam turbines. The residual heat after primary extraction, directed through other equipment, provides additional heat based products such as industrial scale dry air, chilling by an absorption chiller or hot water. The overall design of the system is scalable for low to high VAM flows or variations in concentrations and is capable of providing the company or community with heating, chilling, hot water, electricity or motive force as needed by the particular site or community. The Multi-generation system uses heat from three sources to provide clean efficient energy while mitigating the atmospheric emissions of methane. These sources are heat from the GT, often considered waste heat, heat from fuel injected into the igniters and heat from the VAM. The opportunity to collect carbon credits may improve the economics. In order to design a system with this capacity, a detailed analysis of the combustion characteristics of three separate flows is required. VAM is the main airflow, having the highest volumetric effect, while the GT exhaust and the additional fuel added to the hot exhaust flow of the gas turbine are lower flows, but have a higher velocity and temperature. The aim of the modeling undertaken in this work is to establish the combustion dynamics, degree of pre-heating required and the geometry essential to the design of combustion based VAM mitigation multi-generation systems.

Aug 1, 2013

By G Metzner, R Rodriguez, C Savage

OK Tedi Mining Ltd. (OTML) is in the process of optimising the concentrator performance. One aspect that has been recently implemented is an upgrade of the existing expert control philosophy on the grinding circuit and this will be the topic of this paper. Ore grinding in SAG mills is a multi-input multi-output (MIMO) process subject to several disturbances, most typical being quick acting disturbances such as changes in ore characteristics like hardness and particle size and slow acting disturbances such as ball charge variations and liner wear. The OTML SAG mills treat ore from diverse ore bodies and receive fresh feed subject to large changes in particle size. These circumstances make these mills particularly challenging to control. In this paper, a comparative analysis is presented between the performance of the OTML SAG mill #2 before and after the commissioning of a hybrid control strategy. The strategy uses Expert Knowledge combined with advanced disturbance rejection to reduce the variability of the main process variables, especially pressure and power. It further optimises the overall operation by driving the SAG mill #2 against process constraints (e.g. high power, high motor temperature and high scats recycle rate) and maintaining the operation at or near this point. This strategy is implemented by a combination of the manipulated variables (i.e. fresh feed tonnage and % solids) at any given time.The paper will present trends and a statistical analysis of the comparative results of the mill operation over a period of months, showing a 30% reduction in mill power / pressure variability and a 12% improvement in average power drawn. An increase in throughput was also observed, but cannot be conclusively attributed to the change in mill control due to other changes that were made to the SAG mill #2 during the period of comparison. An additional benefit includes better acceptance from the operators with improved consistency of the SAG mill #2 operation across shifts.The paper will also discuss further improvements envisaged in the continued optimisation of the grinding control circuit.CITATION:Savage, C, Rodriguez, R and Metzner, G, 2013. Hybrid process control strategy for the Ok Tedi Mining Ltd semi-autogenous grinding mill #2 - A comparative analysis, in Proceedings MetPlant 2013 , pp 202-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By C Thompson, D Connelly

The history of mill liners has evolved over time and this paper tracks the changes and development of liner technology. It provides an overview of the primary types of liners, the design and the materials of construction. The design of a mill liner is driven by application, materials of construction, casting technology and handling issues. The choice of solid steel, grid liners, rubber or composites and magnetic liners is based on many factors.The methods used for monitoring wear and predicting eventual change out time are many and varied. The contribution of discrete element modeling (DEM) analysis in predicting wear profile is discussed.Mill trajectory and DEM software programs are used with great effect to predict the effect of lifter height, face angle, high low lifters or mill speed. In the field, trial and operational experience is used or improvements/design concepts at one operation are applied to another. Broken mill lifters, accentuated wear and other problems can be better understood using hardness testing, chemical analysis and photo micrograph analysis of pearlitic or martensitic structure along with fracture face observations. This forms a part of the typical root cause analysis. However given correct and sound liner and lifter, feed and discharge design media selection, and materials of construction, the majority of premature liner or bolting failure is normally attributed to incorrect operational methods such as excessive high ball to feed ratio, incorrect mill speed relating to lifter ball throw, incorrect media selection, "tramp" material entering the mill charge from upstream or recirculating process and understanding the specific mill operation in question.It is hoped that this paper will benefit mill operators who are faced with challenges of improving wear life and at the same time optimizing mill throughput and performance.CITATION:Connelly, D and Thompson, C, 2013. The selection design and application of mill liners for large wet grinding mills, in Proceedings MetPlant 2013 , pp 133-140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By J S. Dunlop

At its most basic level, minerals project management may be broken down into a series of logical chronological phases, described in this paper as: exploration, discovery; scoping and pre-feasibility; feasibility and approval; project financing and commissioning; operation; expansion and closure. Each phase has its own peculiarities and challenges, any one of which can potentially upset the forward progress of a minerals project.Reference is made to each of these project phases based on the authorÆs many years of first-hand experience, in an attempt to identify issues within the project management spectrum where additional caution may be warranted. Left un-addressed, these issues can cause undue delays in the project timeline, ultimately delaying approval at significant project cost.Finally, reference is made to the Mine ManagerÆs Handbook recently published by the AusIMM which is an excellent project management resource, considered to be very relevant for minerals treatment plant managers, whether the context be constructing, operating, expanding or shutting down.CITATION:Dunlop, J S, 2013. Mineral project management - A perspective from four decades in the industry, in Proceedings MetPlant 2013 , pp 13-27 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By S Vianna, K Caldwell, R Silva, T Olson, D Bell

Studies to enhance the FLSmidth forced air machine through changes in the design, showed important improvements through changes in the number of Rotor blades, stator designs, rotor air distribution and other designs features. The main outcomes from this study highlighted that increasing the number of rotor blades increased the selectivity while decreasing power requirements while stators with slots have better results in terms of recovery, flotation efficiency and selectivity than without slots.Also the rotor air distribution makes a difference in the design when comparing different distribution criteria whilst keeping all features of shape and number of blades etc constant. At the most efficient rotor air distribution design, copper recovery reached one of the highest values while keeping good selectivity. The possible explanation for that is the increase in the pump capacity indicated by the increase in the specific power.It was seen as significant that reduction in specific power for some designs tested compared with the then current standard design had an average of 30% less power consumption.As a result, FLSmidth was able to identify new designs that decreased power and improved recovery, as well as, identifying some designs that specifically improved fine and/or coarse particle recovery.CITATION:Silva, R, Caldwell, K, Bell, D, Olson, T and Vianna, S, 2013. FLSmidth flotation developments - Dorr Oliver machines, in Proceedings MetPlant 2013 , pp 413-430 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By A Bax, G Wardell-Johnson, A Giblett, W Staunton

This paper presents a number of key considerations for process development testwork as a reliable basis for the inclusion of gravity separation in gold recovery flowsheets. Operating data, experiences and numerous case studies are also discussed in support of identifying best practice principles for gravity circuit design.CITATION:Giblett, A, Bax, A, Wardell-Johnson, G and Staunton, W, 2013. A review of best practice in gravity circuit design and operation, in Proceedings MetPlant 2013 , pp 272-284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013