Search Documents

By K. Hori

In this study, the determination of optimal conditions for jig separation has been investigated with a TACUB jig separator. The TACUB jig, from which a Batac jig originated, is a useful gravity separator that is effective to separate crushed solid wastes as well as coarse ores. A mixture of crushed polyethylene (specific gravity 1.3) and polyvinyl chloride (specific gravity 1.5) was separated by a batch TACUB jig by varying the frequency (wavelength) and the amplitude (pulse stroke length). It was found that the sample particle layer in the separation chamber was fluidized without turbulence by the rising water pulse resulting in the separation. However, a too strong water pulse reduced the efficiency of the separation of the particles. The results indicate that the specific velocity of the rising water is necessary to fluidize the particle layer without turbulence to separate the particles. The expansion ratios of the thickness of the particle layer in rising flows were measured in a cylindrical column. The pressure losses by the particle layer were calculated from the expansion ratios and the velocity of the rising flows by Ergun?s equation. The curve of the pressure loss vs. the velocity of rising flow showed a maximum point corresponded to the point of fluidization. The velocity of a rising flow on the point of fluidization provided the optimal separation condition.

Jan 1, 2014

By A. Norori-McCormac

"Air recovery, the fraction of air entering a flotation cell that overflows the cell lip, is linked to flotation performance, and it has been shown through industrial testwork that operating flotation cells at air rates that yield the Peak Air Recovery (PAR) results in high mineral recovery. For operating parameters over which flotation plants have little control, such as particle size, investigating the effect on the position of PAR, and the subsequent effect on flotation performance, proves more challenging. To this end, we have developed a bench scale flotation system that runs continuously and exhibits froth behavior similar to that found industrially, allowing the study of such parameters as particle size in addition to air rate. The bench scale system comprises a 4 l baffled cylindrical flotation cell, stirred by a Rushton impeller. The concentrate is recycled back into the pulp, allowing for continuous operation. Glass beads are used as solid particles, allowing a wide range of particle sizes to be tested, with TTAB as collector and MIBC as frother. The system allows operation at air rates typical of industrial flotation systems (1 -2 cms-1 superficial gas velocity), in addition to yielding a froth that coalesces and bursts and exhibits a peak in air recovery as cell air rate in increased. Solids and water recovery is also measured. The results show that air recovery is sensitive to changes in particle size. The intermediate size distribution showed a peak in air recovery (PAR) that corresponded with the maximum solids flowrate, as found industrially. It is shown that finer particles do result in more stable froths and higher recoveries, particularly at low air rates. The effect of particle size on the position of PAR is not yet unequivocally determined from these results."

Jan 1, 2014

By Y. G. Sun

This paper mainly reported separation manganese silver oxidized ores process by amylum de-gradation reduction and its influencing factors. When dosage is given according to nMn : nH2SO4 : n(C6H10O5)n : nH2O=1:k21.8: k116.66:30, the amount of up to 95.93% Mn leach rate and less than 2% silver loss can be obtained. Cyanidation process was used to extracted silver from leaching Mn residues. Silver leach rate could reach 94.15% at consumed amount of 1kg/t NaCN for 1h. Silver leach recovery rate was more than 92.27% by leaching Mn and cyanidation two-step processes so manganese and silver were separated effectively.

Jan 1, 2014

By Hongbo Zhu, Kun Yang, Jingyan Jia, Jinhui Peng, Libo Zhang, Yi Xia

"Titanium dioxide is broadly considered as the most potential useful photocatalytic material. In this work, titanium dioxide was synthetized by microwave solid-state method and characterized by thermogravimetry-differential scanning calorimetry (TG-DSC), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The result demonstrates that through microwave solid-state synthesis, we can obtain uniform size and anatase TiO2 photocatalyst, with the precursor being Ti(C2O4)2·2H2O. And its degradation kinetic parameter of MO can reach to 0.21232.IntroductionSince Fujishima and Honda found the photovoltaic property of titanium dioxide TiO2 [l], it has been widely used in the field of pollutant degradation, virus killer and environment protection [2-5]. Compared to other semiconductors, TiO2 has the advantage of low toxicity/cost, chemical stability, excellent photocatalytic activity, and long lifetime of electron/hole pairs, thus it is considered to be a most potential useful photocatalyst material [ 6]. Solid-state synthesis of oxide nanoparticle is a new method developed in recent years, which not only overcomes the shortcomings of easily aggregation existing in traditional hydrometallurgical process, but also fully demonstrates the unique technologic advantages of without solvents, high yield, easy control, less environmental pollution in solid-state reaction [7-11]. Researches show that the new method of microwave synthesis shows a lot of advantages such as fast reaction rate, efficient, high purity of product, uniform morphology, energy-efficient, and nonpolluting [12-15].In this work, we associated microwave heating and solid-state synthesis to prepare TiO2 photocatalyst material. Its photocatalytic activity was studied in the degradation of MO queous solution. Meanwhile, the formation process as well as the crystal structure and morphology of the synthesized powders were characterized by means of chermogravimetrydifferential scanning calorimetry (TG-DSC), X-ray diffractometry (XRD) and scanning electron microscopy (SEM) techniques."

Jan 1, 2014

By J. Daraisme

Société le Nickel (SLN) exploits the Dôme lateritic nickel orebody at its Tiébaghi operations in New Caledonia. The site geology has an obvious bearing on recovery and metallurgical performance, and the controls are extremely complex at all scales: lithology, oxidation-reduction conditions, mineralogy, and multivariate geochemistry. In that context, establishing an adapted recoverable resource estimation method that is efficient and transparent proves an interesting challenge. The method must address the key notions of: ? Support effect: the exploration data-set can only warrant the estimation of large panels 20×20×3 m3, which are much larger than the selective mining units (SMUs) of 5×5×3 m3 ? Information effect: the selection at production stage uses estimates based on information much denser than that available for mine planning. The problem is rendered more complex in this type of deposit by the fact that the additive variables used for any estimation process (metal accumulation and ore tonnage) are not the ones used to establish the selection at mining stage (i.e. the nickel grade of SMUs, which is the ratio of accumulation on tonnage). Eventually, the selection criteria involve not only Ni grades but also other constituents such as Al2O3, Fe2O3, MgO, and SiO2. The solution presented in this paper is the construction of a platform of SMU multivariate simulations in the saprolitic horizon, together with efficient post-processing aimed at producing the multivariate recoverable resource estimates. The efficiency constraints imposed by the number of blocks to be simulated (1.5 million) lead to resorting to direct block simulations. The underlying multivariate discrete Gaussian model (DGM), the validity of which is tested beforehand, is put to good use to mimic the selection process at the mining stage, by offering the ability to simulate in each block a composite value located at random within the block. Finally, the paper presents the application of a scenario reduction algorithm to pick a representative subset of a few simulations to help appraise the risk attached to the downstream phases (reserve optimization, mine sequencing) of the project. The implementation presented here is for the first generation of the Scenario Reduction plugin built in Isatis software, where measuring the distance between the initial set of scenarios and the reduced set is based on Ni quantities only. Research is under way to adapt the measure to the true multivariate nature of the problem.

Jan 1, 2014

By M. Kinnunen

Handling of municipal solid waste (MSW) and control of its potential resources is becoming increasingly important in modern society. The OECD (Organization for Economic Co-operation and Development) average on municipal waste produced in 2003 was that of around 570 kg per inhabitant. In European Union countries around half amount is of MSW landfilled. In Finland still 88% of MSW was landfilled in 2004. Since incineration reduces MSW volume significantly while producing heat energy, it has become one of the most common waste handling techniques. The shortcoming of incineration is however, that incinerated MSW is often not pre-sorted and it produces slags and ashes as side streams from which recovery of metals is difficult. This paper looks into possibilities of scrap metal recovery for recycling from municipal solid waste incineration (MSWI) bottom ash. In order to do that, a flow sheet of physical separation methods was developed and tested with Finnish rotary furnace MSWI bottom ash. In addition, an empirical model for estimation of the recoveries of scrap metals with physical separation methods for treatment of MSWI bottom ash was developed. According to the results of this study, for 1 Mt of incinerated MSW with 30% mass reduction, a minimum resource potential of 100 kt for magnetic metal scrap of roughly 24 % grade and about 19 kt of non-magnetic metal scrap of roughly 65 % grade. In other words, 57 kg magnetic scrap and 12 kg non-magnetic scrap per inhabitant at the mentioned grades, respectively. Although wide variations of parameters affect the MSWI bottom ash quality, it can be said that a considerable amount of metals is drained into MSWI bottom ash. Results of this study show that from MSWI bottom ash significant material streams metal scrap can be reintroduced into the resource cycle which would otherwise be lost.

Jan 1, 2014

By S. Jayasekera, A. M. T. S. Bandara, J. Kyle, E. Koenigsberger, L. Koenigsberger

The extraction of rare earth oxides from fluoroapatite rich phosphate concentrates often involves a weak acid leach of fluoroapatite and a sulphuric acid bake of the leach residue followed by water leach and precipitation to obtain an intermediate product. The main aim of this study was to determine and rationalize the solubility of rare earth metal ions in synthetic solutions representing various process liquors at the temperatures 40, 60 and 80oC. The liquors contained different acid and metal ion concentrations with respect to sulphuric acid, phosphoric acid and sulphate salts of sodium, magnesium, aluminium, potassium, calcium and iron(III). A solid of mixed rare earth carbonates was used as the source of rare earth metal ions. The solubility tests and characterization of solids using XRD were conducted at Murdoch University laboratories as part of the process development for the Arafura Resources Nolans rare earth project. The composition of initial carbonate solids and the solids and solutions formed after saturation were analysed for rare earth and other elements at TSW Analytical Laboratories in Perth using ICP-MS and ICP-OES. The precipitated solid in sodium-rich acidic sulphate solutions is the double salt NaRE(SO4)2 based on the solid assays. However, in acidic solutions free of sodium or of low concentrations of sodium the precipitated solid appears to be RE2(SO4)3.

Jan 1, 2014

By L. M. Lowe, D. G. Feasby, J. R. Goode

"Rare earth resources usually contain minor amounts of radioactive elements. The most widely recognised sources of radioactivity are associated with thorium and uranium. However, also present in the resources are isotopes of rare earth elements (REE) that are themselves radioactive, including lanthanum (La-138), lutetium (Lu-176) and samarium (Sm-147). These radioisotopes, as well as remnants of the natural thorium (Th-232) and uranium (U-238, U-235) decay series, can contribute to significant levels of radioactivity in mixed REE concentrates and in separated products. Levels such as these can present challenges for transport, transboundary movement, product storage, workers’ health and safety, as well as waste management issues at the facilities that separate out the individual REE’s. These are discussed in this paper. A particularly challenging radioactive isotope is Ac-227 (a decay product in the U-235 decay series). Actinium behaves chemically similar to lanthanides and hence normally concentrates with REE multi-element composites. Reliable analysis of Ac-227 is not widely available and the methodology required to deal with this challenge is briefly described. A principle reason for minimization of radioactive content throughout REE processing is restrictive specifications by concentrate purchasers in order to reduce waste management challenges. Approaches to the minimization of radioisotope content in REE concentrates and separated products are outlined in this paper."

Jan 1, 2014

By Patrick Polk

For many years, sulfuric acid producers all over the world have been forced to meet ever more strict environmental regulations to reduce SO2 emissions. The sulfuric acid industry has implemented new solutions in order to comply with the new lower SO2 emissions target. Haldor Topsoe (Topsoe) has responded to this challenge by continuously improving the range of VK sulfuric acid catalysts and providing tailor-made catalyst solutions to meet the demands of the sulfuric acid producers for lower SO2 emissions. Reducing emissions through catalysis: requires less capital than installing a scrubber, requires no additional process chemicals, generates no waste or by-product to dispose of. In 1996 Topsoe introduced VK69, a cesium-promoted vanadium catalyst, designed for operation in the pass(es) after the intermediate absorption tower in double absorption plants. The high activity of VK69 allows for a more than 50% reduction in SO2 emissions from existing double-absorption plants. Topsoe currently has more than 110 installations of VK69. To comply with the still more stringent regulations being placed on the sulfuric acid industry to lower SO2 emissions, Topsoe has developed a new sulfuric acid catalyst designated VK-701 LEAP5™. This catalyst was introduced to the market in 2010. VK-701 LEAP5™ is based on a novel technology which circumvents the internal transport deficiencies of existing commercial sulfuric acid catalysts and thereby offers exceptionally high activity in strong, SO3 rich gases. Sulfuric acid plants have used this catalyst to meet emissions requirements lower than previously believed possible with a catalyst only solution. This paper will present examples on how to reduce emissions by implementing a tailor-made catalyst solution using VK69 and VK-701 LEAP5™.

Jan 1, 2014

By M. K. G. Vermaak

Kimberlite weathering has been a topic of ongoing research within De Beers for many years. Using kimberlite weathering as an alternative to crushing has many advantages e.g. power and reducing diamond breakage. Weathering could also possibly be used in conjunction with crushing just to weaken the material and reduce power consumption. These forces have driven current research to investigate whether kimberlite weathering could be utilised for these reasons. Weathering in this context does not refer to weathering over long period of time but rather to disintegration of the material in aqeous media in relative short time periods. Previous published work discussed that the presence of smectite renders kimberlite weatherable and that the amount of smectite determines the rate of weathering (Morkel and Vermaak, 2006). The current work investigates whether cation ex-change or the adsorption of organic species in the smectite interlayer could influence the observed weathering behaviour. The results show that cation exchange does take place in the presence of cation species and that the weathering behaviour can be drastically improved with especially Cu2+ cations. Concentration and time effects of the weathering was also investigated. Weathering tests with organic species such as ethanol, methanol, edta, pentanol, butanol, acetic acid and oxalic acid was performed. The results show that organic species does improve weathering but under these testing conditions was not as effective as cations.

Jan 1, 2014

By Denise Crocce Romano Espinosa, Andrea Moura Bemardes, Jorge Alberto Soares Tenorio, Daniella Cardoso Buzzi, Tatiana Scarazzato

"In copper plating processes, a fraction of raw materials are incorporated to the final products, while other portions are discarded as effluents. In this study, the application of electrodialysis (a membrane treatment process) was studied for treatment of wastewaters from cyanide-free strike baths, in order to reuse the components of this bath: copper and HEDP. The synthetic solutions studied consider 1 % of ion concentration of the bath used in this process, simulating the rinsing waters to be discarded. The electrodialysis allowed a percentage extraction up to 73% of copper ions and 72% of HEDP from the effluent. Complexes formation between the acid and copper indicates the possibility of recovery of components in the same compartment, obtaining a concentrated solution of these substances that can be reinserted in the process, for compensating drag-out losses. A diluted solution is also obtained, that can be reused as water in rinsing tanks.IntroductionIn metal finishing industries, contaminants in wastewater and the type of treatment required are determined according to the type of operation [l]. Generally, electroplating industries employ conventional wastewater treatments, e.g. oxidation of cyanide and chemical precipitation. This stage promotes reactions with soluble compounds to produce an insoluble precipitate, removed by physical separation. The sludge is dried by press-type filters [2].In this manufacturing sector, part of the raw materials are discarded as hazardous waste. The cost of discarded compounds and the treatment and disposal of waste may compromise profit margins. In addition, water consumption per unit of production stimulates the development of methods able to recover and reuse the largest possible amount of water [3].In some plating processes, cyanide-based substances are used as complexing agents and as raw materials in form of metal salts [4]. However, the toxicity associated with cyanide has been promoting research for the development of new raw materials in plating processes.A study conducted in Brazil [4] evaluated the modification of a commercial cyanide-free bath for processes of copper coating on Zamak. In the performed study, a new alkaline copper bath was formulated using l,hydroxyethane-1,1-diphosphonic acid (HEDP), an organic compound known for forming stable complexes with metal ions.As results of the study, the operational conditions and the formulation of a bath to obtain adherent, uniform and bright layers were established (Table I) [4]."

Jan 1, 2014

By Nikolaus Schneider

"Abstract: The combination of failure in joints of diaphragm walls and their exposure to water pressure may have far reaching effects ranging from water leakage to the risk of catastrophic loss of stability for the retaining wall and civil structures behind it. Investigations of imperfect joints in diaphragm walls have led to the development and testing of a quality tool to monitor the joint integrity of diaphragm walls during construction. By applying independent mechanical sensors (“joint inspector”) to the steel frame of hydraulic or mechanical grabs, it is now possible to record the surface conditions of exposed primary joints during the construction of secondary panels. This allows for the implementation of corrective action during the construction process should joint quality not indicate a watertight connection to the adjacent panel. The joint inspector, used for different types of stop ends, was tested on a full scale test field at several construction sites. The implementation of this new quality tool drives a new quality standard for deep excavations in inner city areas.General introduction to diaphragm wallsDiaphragm walls are reinforced concrete elements constructed using bentonite slurry to temporarily support an open trench in the ground. They are used in two main fields of application in civil construction, as foundation elements for vertical and horizontal loads (barrettes) and as retaining walls for excavation pits.Particularly for deep excavation pits in inner city areas, diaphragm walls are used as temporary or permanent walls of retaining walls. Alternative retaining wall systems would be secant pile walls, sheet piles or soldier piles, but these have disadvantages in structural strength when compared to diaphragm walls. If the vertical load of existing buildings next to the excavation pit has to be accommodated, the most practical solution can be found using diaphragm walls supported by prestressed anchors, steel struts or slabs."

Jan 1, 2014

By Cang Daqiang, Li Yu, Liu Xiaoming, Zong Yanbin

"Utilization of high-quality heat in melting slag is a great challenge for iron and steel industry. In the paper, a new method is put forward to concurrently utilize heat and slag by converting the melting slag directly into high valued materials, slag glass-ceramic. A glassceramic with a higher basicity of 0.7 than traditional basicity of 0.45 was prepared from steelmaking slag in order to utilize more hot melting slag. Effects of Alz03 on its crystallization processes were researched by XRF, DTA, XRD and SEM. Results show that Alz03 in glassceramic would have great effected on its property. When the Alz03 content ranges within 12%-15%, glass-ceramics with basicity of0.7 could reach the best performances. The change of dominant phase in glass ceramics from akermanite and wollastonite to akermanite and gehlenite would significantly degrade its mechanical property. An increase of Al2O3 content leads to a rise of the viscosity and crystallization activation energy of the glass, while results in increasing sintering temperature and crystallization temperature of glass, which contributed to its fully crystallization and densification process.IntroductionSteel slag is a by-product under a process of converting iron to steel at above 1600°C, and 0.1-0.15 ton molten steel slag would be discharged for producing per ton of steel in the process. The discharged steel slag at 1600°C has heat of 68 kgce/t. In 2012, China's steel output reached 716 million tons, and produces about 100 million tons of steel slag and 68,000 tee of heat in it [1,2]. But at present, utilization of both slag and its heat at 1600°C is a great challenge for iron and steel industry.Dry granulation of melting steel slag by air and then recovering the heat of the hot air are a traditional technology which have not yet been put into practice for very low heat conductivity of the slag and low efficient of heat exchange among the different processes [3,4]. Therefore, a new method for high efficient utilization of both steel slag and its high temperature sensible heat is put forward [5,6], which is on-line reducing and extracting iron from molten steel slag and then directly preparing glass-ceramic by use of the residual molten slag."

Jan 1, 2014

By T. Gong

Often plans to increase plant throughput provide an opportunity for optimising plant equipment and operating methods. This was the case in 2005 at TISCO Jianshan Iron Mine, when an increase in production was planned. The thickening circuit had presented a limitation to the plant throughput and operation with poor overflow clarity and underflow density. Following a course of test work by Outotec, a 53m diameter Supaflo® High Rate Thickener (HRT) was selected for the duty. From early stages of operation of the new thickener, the benefits have been dramatic, including: ? Improved tailings underflow density by 9% ? Improved Overflow clarity to less than 150ppm ? Considerably decreased the water and energy consumption as well as operation cost ? Stable and reliable operation This paper looks at this installation as a case study and compares the previous thickener installa-tion performance with the performance of the single 53m HRT.

Jan 1, 2014

By Marco Le Roux, Quentin Campbell

"Most coal supply contracts include strict limitations on the moisture content of the products. This limitation exists because of calorific, transport cost, and handling reasons. Managing the retention time on product stockpiles to facilitate drainage commonly controls the moisture content in coarser coal products. A large-scale pilot rig has been commissioned to facilitate research in this regard. A stockpile of about 15 tonnes of a typical washed power station feed coal from the South African Witbank coalfield was loaded onto a 6 x 6 m platform on load cells. The platform was shielded from the elements, like rain and wind, and an artificial rain sprinkler system was installed. A variety of rainfall intensities and durations were simulated and the water accumulation and run-off was measured. The material was also sampled for moisture and particle size before and after the series of tests. At the same time, the drainage characteristics of the same coal were determined in smaller scale drainage columns for comparison. Data is presented in this paper on the drainage rates, maximum accumulated moisture, final moisture, and the effect of evaporation. The results showed that for all rainfall patterns tested, drainage ceased after 2 - 3 days, but evaporation continued for at least the time period under investigation, albeit at a low rate. Evaporation contributed to dewatering at rates that depended on wind, temperature and humidity conditions. This caused a slow reduction in moisture content even after the run-off had ceased. The value of the final moisture depended on the coal PSD. It was also found that the intensity and duration of the more intense rainfall events did not significantly affect the maximum water accumulation, with drainage rates equaling the corresponding water addition rates which suggested that water ran off over the surface of the stockpile with limited penetration. During more intense rainfall scenarios, some penetration was apparent."

Jan 1, 2014

By Lev Filippov, Lorène Dessalas, Inna Filippova, Yves Foucquet

"Seafloor massive sulphide (SMS) deposits, similar in composition and genesis to terrestrial volcanogenic massive sulphide deposits, are generally found in volcanic seafloor environments along major rifts and mid-ocean ridges. Theyare associated to extensional tectonic settings such as nascent-arc, rifted-arc and back-arc environments. They may represent important source of base metals and be an alternative to on-land resources. Seafloor massive sulphide deposits have particular mineralogical compositions and textural features differentiating them from terrestrial one. When extracted from salty water and exposed to the ambient air, massive sulphide samples strongly oxidize and soon become covered by thin layers of iron, copper and zinc rich sulphates and oxides, as well as elemental sulphur. The textural properties vary according to the degree of maturity and the sample position within the hydrothermal deposit. The total porosity of that type of samples is also relatively high, especially for immature samples such as black smoker chimneys, which can reach 15% of total porosity. Because the secondary mineralization and porosity level are different, seafloor massive sulphides ores respond differently from terrestrial ore to processing methods. Froth flotation, commonly applied to separate all type of sulphides from the gangue, is one possible technique for processing seafloor ore. Sulphide recovery rate is, in most cases, excellent (>90%) however separation of the various mineral phases is difficult to obtain even when applying known methods used for terrestrial ore. Moreover, the flotation behaviour decreases drastically with the time of conservation at the surface, even when the samples were stored in a confined environment. High pH values, which is a good way to depress pyrite and therefore to favour the flotation of copper and zinc sulphides, do not have the same effect on seafloor ore. Consequently, careful flotation procedure must be elaborated to obtain efficient mineral separation technique for this specific marine ores."

Jan 1, 2014

By Florian Bauer

The Fording River mine in British Columbia produces hard coking coal in an open pit operation. Coal seams are exposed by blasting overburden and digging blasted muck with rope shovels. The drilling and blasting process presents a considerable cost factor to the operation. Reducing the amount of explosives needed therefore contributes considerably to costs saving initiatives. However, reducing the powder factor only makes sense if the subsequent loading processes by the shovels are not compromised in terms of productivity.

Jan 1, 2014

By Y. Z. Ma

This paper presents a matrix formulation of factorial kriging, and its relationships with simple and ordinary kriging. Similar to other kriging methods, factorial kriging can be applied to both stationary and intrinsic stochastic processes, and is often used as a local operator. Therefore, the concepts of intrinsic random function and local stationarity are first briefly reviewed. Kriging is presented in a block matrix form in which the kriging solution is useful not only for understanding the relationships between simple and ordinary kriging methods, but also the relationships between interpolative kriging and factorial kriging. When used as a signal/noise-filtering method, factorial kriging is especially useful for multiscale modelling. Examples for general signal analysis and geophysical data signal filtering are given to illustrate the method..

Jan 1, 2014

By Thenepalli Thriveni, Seong-Young Nam, Nam-Il Um, Joobeom Seo

In the present work, we report a novel microstructure of synthesized scalenohedral PCC (precipitated calcium carbonate) without any additives by a simple and ecofriendly carbonation process carried out in a liquid-gas system on the crystal growth of the scalenohedral calcite phase. Especially, the process parameters of Ca(OH)2 concentration and CO2 flow rates were investigated to enhance the sensitivity of the process. The highest average length of the scalenohedral calcite was obtained at pH 6.0, temperature 450C, Ca(OH)2 concentration 0.2M, CO2 flow rate 80mL/min, and total volume 1L. The utilization of flue gas-derived CO2 from coal fired power plants could be a form of carbon capture and storage using carbonation reaction with scalenohedral PCC. Finally, the synthesized scalenohedral PCC was used as a filer for ONP recycling. We demonstrated all these experiemnts at semi pilot plant scale.

Jan 1, 2014

By J. Rabe

Tasked with developing a flow sheet for a new resource, one typically turns the experts for help. The advice of an expert can be invaluable in reducing the time and costs associated with characterizing an ore (not to mention extracting maximum information from limited samples). While guiding and optimizing a metallurgical concept study requires a certain skill set, selling a project is something different. The metallurgical specialist is usually not responsible for sharing the results of investigations with potential investors. However, the person responsible for selling the project can ensure that a metallurgical concept study is conducted thoroughly and responsibly without having the ability to do the work, while being sufficiently familiar with the metallurgical aspects to authoritatively sell the project. The process of identifying suitable process routes through to constructing a concept flow sheet and mass balance is discussed as a basic example. From basic mineralogical information and a thorough literature survey, the most likely beneficiation routes can be identified and targeted testing conducted. The final top size will depend on the required product properties (mainly grade), the selected beneficiation technology, and the ore?s liberation properties. Once the required top size has been identified, comminution options can be evaluated. Once again, literature surveys can be used to supplement concept-level comminution property information, and select possible equipment and circuit configurations. Marketing, material handling, and logistics-related information can be used to determine required dewatering technologies. At this stage, enough information is available to develop a concept mass balance and conduct basic equipment sizing..

Jan 1, 2014