Search Documents

By G. Pan

Although geostatistical techniques have been widely accepted as the standard methods for reserve calculations in the mining industry, the production data of many mines frequently differ from geostatistical estimations based on exploration and development drilling. The discrepancies in recovered metal amounts, commonly in the range between 10% and 30%, are related to different factors. Major causes vary from mine to mine. A common cause, however, is the ignorance of important geological constraints in reserve modeling. Three major factors appear to be related to such an unfortunate fact: 1) modelers are over-confident on geostatistical techniques, 2) it is difficult to establish geological models, and 3) mine schedules are too tight to allow detailed geological modeling work. Defining mineralization envelopes has been a major effort in geological modeling. Past experiences have showed that geological modeling is much mo~ demanding than the choice of sophisticated kriging estimators. Since building envelopes for complex ore bodies can be extremely tedious and time-consuming, computerized approaches are badly needed for mine modelers. A comprehensive procedure reported here is referred to as probability-assigned constrained kriging (PACK), which includes a built-in method for defining 3-d mineralization envelopes. The modeling technique is fast and accurate for complex precious metal deposits. The technique is demonstrated on a gold deposit. The estimation results are compared with blast-hole based production panels, showing that the estimated tonnage is 2.2% larger than the actual production and the average grade is 2.6% lower.

Jan 1, 1994

By K. S. E. Forssberg, J. A. Jirestig

Laboratory investigations on the possibility of using magnetic separation for the recovery of sulfide minerals have been reported. A survey of several sulfide ores and flotation concentrates indicated that, in most cases, magnetic separation is not a suitable primary beneficiation method. However, encouraging results have been obtained in concentrate purification. At the Boliden complex sulfide ore concentrator in Garpenberg, Sweden, an Allis-SALA Mark III carousel High Gradient Magnetic Separator (HGMS) is used with a small flotation circuit to recover sphalerite lost to the galena concentrate during lead flotation. After four years of refining the HGMS process, there has been an increase in zinc recovery and an enhancement in the quality of the lead concentrate.

Jan 1, 1994

By R. Flores V.

The Refugio Project is located in the Andes mountains of northern Chile, in the Maricunga Hineral Belt. The Verde, Pancho and Guanaco Au ore bodies have been recognized and are Early Miocene in age. Mineralization consists of fine-grained disseminated gold hosted by dacitic to dioritic subvolcanic porphyries. Alteration comprises massive to veinlet-controlled silicification overprinted on earlier potassic and propylitic alteration and surrounded by later argillic alteration. Geologic relationships suggest that the Refugio ore bodies occur within an Early Tertiary volcano overlying Paleozoic and Mesozoic basement rocks. Geologic reserves at Refugio are approximately 300 million grams (9.7 million ounces) of gold. The Verde deposit contains 185 million tonnes of mineable and leachable ore with an average grade of 0.90 glt Au and is currently in the pre-construction stage after a positive feasibility study. Proven and probable mining reserves at Verde deposit are 101 million tonnes at an average grade of 1.02 glt gold. Additional potential exists at to other deposits within the Refugio property (Pancho and Guanaco) but no reserves have yet been defined due to the limited drilling to date.

Jan 1, 1994

By G. Bonifazi

The study of minero-petrographical characteristics and the subsequent textural and structural characterization of an ore mineral represents the first step of each industrial processing whose aim is the beneficiation of each valuable mineral phase present inside the ore. Analytical, mineralogical and petrographical, chemical and multispectral image analyses based investigations, applied to eclogitic ore samples deriving form "in situ" sampling campaigns, were applied. These procedures enabled to point out some textural and structural aspects characteristics of ore litotypes belonging to eclogitic-amphibolitic dikes. Such dikes are characterized by a paragenesis constituted mainly by siliceous gangue and accessory "useful titanium minerals" as rutile [TiO2], "pseudolilmenite", ilmenite [FeTiO3] and sphene [CaTiSiO5]. In the beneficiation process applied to ore s is of preliminary importance to establish a strategy in order to obtain a recovery of high quality "mono-minerals concentrates" as rutile, "pseudolimenite", ilmenite and phene. To reach this goal is thus necessary to develop a preliminary study of the textural, structural, petrochemical and minerochemical characteristics of the samples. Different ore samples (eclogitic rocks), resulting from sampling campaigns carried out in the Piampaludo area (Sassello district: Savona, Northern Italy), are examined.

Jan 1, 1994

By J. A. Porter

This paper uses project examples, primarily associated with large iron ore mines in Brazil, to demonstrate opportunities for the mining industry to go beyond traditional compliance and impact mitigation to proactively operate within the ethics of environmental and economic sustainability.

Jan 1, 1994

By B. R. McEwen, A. N. Samis, J. H. Gray

"The Quebrada Blanca Copper Mine is an open pit copper project located at 4200 m elevation in the Chilean Andes. The deposit is a world-class supergene enriched porphyry with a mining reserve of 89 Mt of 1.3% copper. The supergene zone will produce 6.3 Mt of ore per year for more than 15 years to produce 75 000 t of cathode copper per year.This paper will review the project geology the computer model ling of the deposit, the mine planning process and the property production scheduling. With copper production .fixed by the onsite electrowinning capacity, the planning and scheduling aspects to optimize the project NPV will be discussed. Some of the logistics, equipment. personnel and process difficulties of operating a mine at 42()() m elevation will also be described. IntroductionProject DescriptionThe Quebrada Blanca Copper Mine is an open pit copper project located in the northern part of the Chilean Andes. The project is based on the supergene enriched portion of a porphyry deposit which has a mining reserve of 89 million tonnes at 1.3070 copper. Below the enrichment blanket, the protore represents a further resource.All ore will be leached, the higher grade material will be crushed and stacked for thin layer heap leaching, and the lower grade and oxide material will be dump leached as run-of-mine material. Solvent extraction and electrowinning will be used to produce 75 000 tonnes of cathode copper per year. Power will be supplied by a 40 MW on-site diesel generating plant with the waste heat being used for process heating. The leaching operation will operate in excess of 15 years and may be followed by open pit mining and conventional ore concentration of the underlying primary sulphide mineralization.Because of the dry location water will be piped 37 km from a ground water source at the Salar de Michincha. Water requirements will be approximately 1.5 million m3/year. The operation will eventually employ approximately 550 people on a 7-day-on, 7-day-off rotation with two twelve-hour shifts per day with an on-site camp. Busing will be provided to the port city of Iquique."

Jan 1, 1994

By Philip Bonanno

The first major project in Boston's new access to Logan Airport was an Immersed Tube Tunnel which extended 3,600 ft. from South Boston to East Boston across Boston Harbor. Twelve tube sections, 300 ft. long x 80 ft. wide x 40 ft. high, were lowered into an excavated trench which was then backfilled. The depth of the trench at mid-channel was approximately 100 ft. below mean high tide. At the East Boston end the tube terminated close to the present shoreline. At the South Boston end the tube terminated approximately 600 ft. inland from the shore line where a ventilation building was required. The depth to subgrade from existing ground at the ventilation structure was approximately 85 ft. The soil profile at this location consisted of 50 ft. of miscellaneous rubble fill, 25 ft. of Boston blue clay, and 10 ft. of glacial till. A small amount of weathered argellite existed at the north end of the structure. Part of the Morrison Knudsen, Interbeton, J.F. White, Joint Venture contract to construct the Immersed Tube Tunnel (ITT) was the construction of a cofferdam at the tube/ventilation building interface. The ventilation building was to be built as part of another contract. The construction of the cofferdam and the excavation to the building subgrade was the responsibility of J.F. White Contracting Company.

Jan 1, 1994

By A. L. Garassino

Dans cet article on parle sortout de l'approche de calcule pour les pieux charges horizontalement avec particuliere reference aux curbes p-y et è une solution semi-empirique qui prende en consideration les variations typiques du module du sol avec la deformation obtenue par les données expérimentales. 1. INTRODUCTION The analysis of the piles under lateral loads depends very strictly from the pile stiffness and geometry, from the soil type and from the strain field. Different approaches were adopted in solving the problem. Some Authors developed methods for estimating the ultimate lateral resistance of piles and pile groups by conventional static approaches, as the Brom's widely known (1964) or by the plane strain solution developed by Davis (1961) or by empirical engineering con­siderations l

Jan 1, 1994

By W. F. Van Impe

The design of piles and of pile groups has remarkably progressed over the past two decades. The in­creasing complexity of the building concept implements a more rational approach of the deep foundation capacity and its interaction with the structure. Moreover, the understanding of the soil characteristics relevant to deep foundation behaviour, is continuously in progress because soil parameters are always more accurately determined; which also contributed a lot to the recent developments in pile capacity design. At last, due to the increasing sensitivity of buildings to deformations, continuous attention must be also paid to pile group settlements. The aim of this report is to discuss some of the mentioned more important pile design developments.

Jan 1, 1994

By Betty L. Gibbs

What does the information age mean to mining companies? The perception of greatly increased access to information is based on modern communications through ‘smart’ fax machines and computer networks. Computer media allow us to `talk' to the President or to a sister in Australia. If we need data to help put together a mining permit, we can find that data somewhere on computer media. The vast amount of easily accessible information quickly overwhelms us. To avoid `information burnout,' we must learn to target searches and be able to discriminate between dross and information that is useful to our goals. If you watch commercial TV, you have learned to screen out most product commercials. A similar screening process must be applied to computerized information sources. You may need to sort through a lot of irrelevant information before finding the pearls you are looking for. ‘Smart’ fax machines can send information with no direct human intervention. MINES FaxBac, for example, from the US Bureau of Mines instructs you to enter four-digit numbers to have particular reports sent directly to your fax machine. Software vendors use a similar system to supply information about their products. You select an item by number, and the related brochure is faxed to your machine. To compete, the industry must maintain access to as many information sources as possible. The availability of computers and software for almost every conceivable application allows us to accomplish work faster than we ever thought possible, even as recently as 10 years ago. Most mining companies have become aware that doing geology, reserves, mine planning and other technical tasks completely by hand is much too slow. The world moves faster, drilling happens faster, mining happens faster, all related activities happen faster. We no longer have the manpower or time to keep all maps. calculations and records up to date.

Jan 1, 1994

By Niels Krebs Ovesen

Close economic cooperation was established among the countries in western Europe during the seventies. As a consequence, among others, a need for harmonized technical specifications for civil engineering works arose. Technical specifications for design and execution of building and civil engineering structures exist in most of the European countries. In some countries such technical specifications are part of the building regulations and in other they are independent codes of practice and standards. The works on the Eurocodes was initiated by the Commission of the European Communities about 1976. The Eurocodes are intended as common unified design codes for different load bearing structures constructed from different materials. They are also intended to cover design of geotechnical structures. They are established with a view to promote the free movement of goods and services within the member states of the European Community - the so called Internal Market - and within the member countries of the European Free Trade Association, EFTA by removing obstacles arising from different rules for calculation and design.

Jan 1, 1994

By D. K. Panda

The behavior of single drops with gas evolution at the interface is of interest because this is one of the important reactions that occur in oxygen steelmaking vessels, where a large amount of iron-carbon drops are dispersed in an oxidizing slag. The carbon dissolved in these drops, reacts with the slag to form CO, which is evolved as a gaseous phase. A room- temperature model was used to study the nature of this type of reaction including the effect of various factors such as viscosity and the presence of surface active impurities. Experiments were done for reacting drops over a wide size range to observe various regimes of behavior. Large single drops were levitated in a counter current flow to produce a sufficiently long residence time to allow the study of the various stages in the reaction. The emphasis of this work was to obtain photographic evidence of a high quality to describe all possible modes of behavior, and so a lot of effort was given to developing and perfecting experimental techniques.

Jan 1, 1994

By W. C. Lacy

It is the responsibility of educators to look ahead and prepare young engineers and scientists to cope with industrial and social problems of the future. We are faced with a review of history as well as prophesy of the future. The mining industry exists in a "bubble" with little interaction or communication with the outside. This isolation must be broken down if the industry is to survive in the U.S. and Canada. The ability to communicate with the general public and public officials is essential. Many changes are occurring that will require readjustments in technology and staffing. Aging population will result in raising retirement and increasing available workforce. This may force shorter working weeks to supply additional jobs. Environmental concerns will likely direct more attention not only to these concerns during mining, but to planning for post-mining land usage. Retraining and up-dating educational programs are required to cope with these changes.

Jan 1, 1994

By Michael D. McGill, Jeff Freadrich

There are many factors which affect the productivity of a front end loader. One of the most obvious is the characteristics of the material being mined. Characteristics such as size distribution, swell factor or heave, and material hardness / abrasiveness will all effect the efficiency of the mucking cycle. The focus of this paper is to look specifically at the size distribution of blasted material, and quantify the effects on loader productivity.

Jan 1, 1994

By Mukesh K. Agarwala

Alloy composite parts were made from powders by Selective Laser Sintering (SLS). SLS is a rapid prototyping process that uses data from CADICAMICAE systems to guide a laser beam and rapidly form 3-D prototype parts from powders without any part specific tooling. In this study, Bronze-Nickel parts made by SLS were studied for their mechanical properties. To make the parts structurally sound, SLS parts were further processed by conventional isothermal sintering, without loss of shape. The resultant densification and mechanical properties were studied and related to microstructures and P/M densification models. These results were then correlated to the SLS processing parameters.

Jan 1, 1994

By Thomas M. Barczak

The engineering of a support system is driven largely by economics. The goal is to provide effective support at minimal cost. For this reason, wood has been extensively used as a support material for centuries. The cost of timber for mining applications has risen by more than 50% in the past 5 years and is likely to continue to increase as the supply diminishes and further environmental restrictions are placed on timber harvesting. The increased cost and lack of high strength wood in the Western United States has provided incentives to improve the utilization of wood and to develop alternative support materials. This U.S. Bureau of Mines' (USBM) report discusses the basic engineering requirements for the application of various materials for supplemental roof support construction and provides an overview of support systems that use materials other than wood. A comparison of support performance and cost for various material constructions is made to assist the mine operator in support selection. The scope of materials discussed in the report include: (1) conventional mine timber loaded perpendicular to the grain, (2) parallel to the grain timber loading, (3) steel fiber reinforced and air entrained concrete, (4) steel, (5) granular fill materials, and (6) combinations of these as composite support structures. The range of support systems analyzed include wood and concrete cribs, concrete columns and props, steel beams, friction props, and several novel support concepts.

Jan 1, 1994

By T. P. Meloy

Like our wives, the comminution of brittle solids is easy to recognize but difficult to describe. However, describing it we must. Describing the fracture mechanism of brittle solids permits the eventual mathematical quantification of the results, process optimization and control strategies. This paper presents a physical model of brittle solid comminution that explains why the slope of the log-log size distribution curves have a slope of one or less in the smaller particle sizes. To develop the hypothesis, modifications of the Gaudin Meloy physical model are made. In brittle solids, comminution takes place by cracks propagating through the material. These cracks may bifurcate as they move. Cracks may terminate either on the original surface of the material, or on a secondary crack within the material formed earlier in the comminution process.

Jan 1, 1994

The initiation of a panel cave is an extremely important and infrequent event in the life of a large underground caving operation. A new cave was initiated at the Henderson Mine in 1991, 15 years after its first cave had been developed in 1976. The original cave was started after a half billion dollars had been invested in the development of the mine, mill and 23 km haulage system. Many things had changed since 1976, the most significant of these being much lower realizations for molybdenum. In 1976 the high demand for molybdenum and uncertainty of caving characteristics, formed the basis for a very conservative cave initiation sequence with miles of boundary weakening and inspection drifting. In 1991 the highly competitive molybdenum market in conjunction with 15 years of caving experience made for a very different mining climate.

Jan 1, 1994

By Gregory R. Wessel

Sulfur is a nonmetallic element widely distributed in nature and of great physical and economic importance. It is the 14th most abundant element in the Earth's crust (0.06%) and an important constituent of animal and plant life. Sulfur has been known and used since ancient times for a number of medicinal and industrial uses. At present, most sulfur is used to generate sulfuric acid that is used in a wide variety of industrial processes, particularly the production of fertilizer. Because of this, sulfuric acid (and hence sulfur) consumption is often regarded as a good index of a nation's industrial development. In the past, sulfur was mined from surface occurrences in several geologic environments, and was used in relatively small amounts. With time, the uses of sulfur and sulfuric acid expanded, as has the need for larger quantities of these commodities. Sulfur is now mined from both surface and underground deposits, and is recovered as a byproduct from a number of industrial processes. Despite valiant efforts and years of work by sulfur explorationists and others, many aspects of sulfur mineralization remain controversial. Almost as controversial is the spelling of the word sulfur. The English spelling sulphur commonly is used outside America and in the American sulfur mining industry, but sulfur is the correct American spelling as approved by the American Chemical Society, the American Geological Institute, and many others. Those new to the American sulfur industry often find it puzzling to be reprimanded for using the correct American spelling. Sulfur resources are abundant and widespread, but the extent to which they can be classified as reserves is constrained by pre- vailing prices and extraction technologies. At present, sulfur can be economically mined from very few deposits. The sulfur industry is roughly divisible into two sectors: voluntary (or discretionary) and involuntary (or nondiscretionary). In voluntary production, the mining of sulfur or pyrites is the sole objective, and the recovery of the resource is as complete as economic conditions will allow. During involuntary production, sulfur or sulfuric acid (termed recovered sulfur) are produced as byproducts, and the quantity of the output is dictated by the demand for the primary product. Voluntary sulfur now accounts for only about 35% of the elemental sulfur produced worldwide, and most inves- tigators believe that voluntary sulfur will be less important in the future. Sulfur sources and products are described as follows (after Barker, 1983): Sulfur Sources: Combined sulfur-sulfur that occurs in nature combined with other elements, commonly referring to sulfides and sulfates. Cupriferous pyrites-pyrite containing minor amounts of cop- per sulfides. Hydrogen sulfide-a toxic gas that occurs in petroleum and natural gas. Involuntary sulfur-sulfur produced as a byproduct in response to legislative or process mandates. Native sulfur-naturally occurring elemental sulfur. Nonferrous metal sulfides-opper, lead, zinc, nickel, and molybdenum sulfides that are processed for their metal content. Organic sulfur complex organic sulfur compounds that occur in petroleum, coal, oil shale, and tar sands. Pyrites-iron sulfide minerals that include pyrite, marcasite, and pyrrhotite. Sulfate sulfur-sulfur contained in anhydrite and gypsum. Voluntary sulfur-sulfur produced in response to market demand. Basic Sulfur Products: Acid sludge-contaminated sulfuric acid usually returned to acid plants for reconstitution. Brimstone-synonymous with crude sulfur. Bright sulfur-crude sulfur free of discoloring impurities and bright yellow in color. Broken sulfur-solid crude sulfur crushed to -8 in. Byproduct sulfuric acid-sulfuric acid produced as a byproduct of a metallurgical or industrial process, generally relating to combined sulfur sources. Crude sulfur-commercial nomenclature for elemental sulfur. Dark sulfur-crude sulfur discolored by minor quantities of hydrocarbons, ranging up to 0.3% carbon content. Elemental sulfur-processed sulfur in the elemental form produced from native sulfur or combined sulfur sources, generally with a minimum sulfur content of 99.5%. Formed sulfur-elemental sulfur cast or pressed into particular shapes to enhance handling and to suppress dust generation and moisture retention. Frasch sulfur-elemental sulfur produced from native sulfur sources by the Frasch mining process. Liquid sulfur-synonymous with molten sulfur. Liquid sulfur dioxide-purified sulfur dioxide compressed to the liquid phase. Molten sulfur-crude sulfur in the molten state. Prilled sulfur-solid crude sulfur in the form of pellets produced by cooling molten sulfur in air or water. Recovered sulfur-elemental sulfur produced from combined sulfur sources (including byproduct hydrogen sulfide, but sometimes referring only to sulfur from fossil fuels) by any method. Slated sulfur-solid crude sulfur in the form of slate-like lumps, produced by allowing molten sulfur to solidify on a moving belt. Specialty sulfur-prepared or refined grades of elemental sulfur that include amorphous, colloidal, flowers, precipitated, wettable, flour, and paste sulfur. Sulfur ore-unprocessed ore containing native sulfur.

Jan 1, 1994

By Michael K. Watkeys, Charlesworth. E. GUY, Jacobus E. Potgieter, Anhaeusser. Carl R., Roger L. Gibson, Alexander F. M. Kisters

Abstract - Intrusive features of cupriferous noritoids from the deeply eroded Proterozoic granite-gneiss terrane of the Okiep Copper District in South Africa illustrate the emplacement of basic magmas into a mid- to lower-crustal environment. The small, easterly trending intermediate to basic intrusions of the so-called Koperberg Suite display a wide variety of geometries, occurrence and emplacement modes, including dike-, sill- and plug-like bodies. Coeval granulite-facies metamorphism, partial melting and ductile deformation of country rock gneisses during intrusion of the basic magmas led to emplacement and dilation processes of the intrusions which differ significantly from those described for dikes and sills at shallow crustal levels. Regional tectonic stresses are largely negligible due to very low differential stress (?1 - ?3) during deformation and intrusion, which permits emplacement at high angles to the principal compressive stress and which follows favorably inclined structural anisotropies. Dilation of the basic intrusions is largely determined by compositional differences of host rocks and occurs by thermal erosion, i.e., assimilation of wall rock gneisses. Low length-to-width ratios of basic to ultrabasic dikes and predominantly diaper -like outlines of mesocratic bodies are indicative of low viscosity contrasts between the mafic magmas and high-grade metamorphic host-rock gneisses. Buoyancy-controlled ascent of the basic to intermediate intrusions is expressed by a broad compositional zoning of basic bodies with respect to the granite-gneiss stratigraphy. Various intrusion modes within the stratigraphic column of the granite-gneiss sequence reflect a lithological and structural stratification of the seemingly homogeneous granite-gneiss terrane.

Jan 1, 1994