Search Documents

By S. K. Kawatra

It is common in coal-cleaning operations to produce a fine waste stream which contains a considerable amount of coal, but which is not economical to recover both because it is mixed with large amounts of difficult-to-remove clay slimes, and because the fines are often heavily oxidized. Conventional froth flotation machines cannot produce an acceptable product from such material in a single stage of flotation, and even flotation columns often have difficulty cleaning this type of feed. A new type of flotation column was designed specifically to deal with these problems, and was installed and tested in a coal-cleaning plant in Ohio. The feed coal contained 39.8% ash as fine clay, and 2.83% total sulfur, and was 80% passing 176 micrometers. The coal was a thickener product which had oxidized for some time, and was very difficult to float. However, using the new column it was possible to recover up to 85% of the calorific value in a product containing less than 11% ash, and up to 60% of the calorific value in a product of less that 8% ash. The bulk of the pyritic sulfur was rejected from the coal as well. Multistage flotation tests showed that the flotation column was able, in a single stage, to produce the best froth flotation product that it was possible to recover from this coal.

Jan 1, 1994

By Preben Ingerslev

Control of the reheating of ingots is based either on surface temperature measurements using optical pyrometers or on furnace set points and reheat time determined empirically. This paper presents a real-time mathematical heat flow model, named BESTT, which calculates the temperature distribution in an ingot cross section when reheated or cooled. The model runs on a 486 PC in less than one minute for a variety of ingot cross sectional shapes such as circular, square and with some considerations octagonal and heavy-cornered square. Initial temperatures can either be uniform or nonuniform while accounting for temperature dependent thermophysical properties. The model was developed and verified using 718 alloy ingots in box type furnaces. When integrated with on-line pyrometric measurements, BESTT can provide for improved feed back in the reheating control loop. The use of BESlT will assist in reducing energy costs, and improving product quality and consistency. EPD Congress 1994 Edited by C. Warren The Minerals, Metals k Materials Sodety, 1993

Jan 1, 1994

Structural geological information is widely used at the Mt Whaleback Mine, Newman, WA. Recent improvements in the structural understanding of Mt Whaleback are providing a very cost-effective way of reducing geological risk, improving the economics of mining, optimising pit design and addressing safety problems. The structure of the Mt Whaleback orebody is highly complex and has a significant influence not only on iron ore genesis but also on pit wall stability. A team approach between the Structural Geology and Geomechanics Groups has been providing excellent results to reduce geological risk at Mt Whaleback.

Jan 1, 1994

By Pat McLaughlin

Blast design in the construction industry has often been based on past practice or powder factors. This is to some extent understandable, since construction projects do not have the longevity of mining or quarrying operations and therefore have less opportunity to pursue potential improvements. The main concern of the operator is whether or not the technique will work, and at what cost to the downstream processes. Time, not long term savings, is of the essence.

Jan 1, 1994

By B. G. Thomas

"Mathematical process models can be applied in several different ways to serve industry by inducing beneficial changes to process operation. This paper attempts to summarize the different uses, types, and attributes of these models, and to offer some ideas to consider when developing, using, and reporting on them. Process models range from empirical to mechanistic in nature and vary in complexity from simple analytical solutions to coupled, 3-D transient numerical simulations. They are classified here according to the way in which they are implemented in practice, viz. fully-online models, semi-online models, off-line models, and literature models. The purpose of the model should dictate how choices are made during its development. Ways to validate and compare the model with experiments are suggested. Examples are taken in the context of the author's experience in modeling the continuous casting of steel.IntroductionThe objective of this paper is to provide a partial introduction for this symposium by discussing some basic aspects of the application of mathematical process models in industry. Essentially, the aim is to explore how process models are used to benefit industry, and to offer some general comments and suggestions, based on the experience of the author, on how models can best meet this goal.This work is concerned with process models, which consist of systems of mathematical equations and constants that are solved on a computer to make quantitative predictions about some aspect(s) of the process. The specific variables required as input data and generated as output data are important features of the model. The equations often derive from a numerical solution to one or more differential equations and their boundary conditions. The model also includes the constants, which represent material properties, empirical relationships, and other knowledge about the process, and usually require considerable effort to obtain. Thus, general purpose commercial software packages, (ie. finite-element or finite-difference based codes), are not models in this context. They are useful tools, however, serving as frameworks for the development of process models."

Jan 1, 1994

By E G. Prado

We have confirmed on bench scale the removal of chlorides and alkalies (+95%) and over 2/3 of the zinc, lead and cadmium from EAF dusts. This has been achieved with arrononium acetate solutions alone, or with combinations of water wash, amonia-ammonium carbonate and ammonium acetate solutions. Also confirmed are the process routes for the recovery of the aforementioned elements into marketable products. The technology involves the complete recycling of the reagents. The FAF residue is returned to the electric furnace without risk of impurities buildup. Commercial scale testing with the recycled dust was satisfactory, including quality of the slag and its behavior during the melting stage. A cursory feasibility evaluation is presented.

Jan 1, 1994

Optimal gold recoveries largely depend on efficient liberation of the gold or gold-bearing minerals as well as on maximum access for the lixiviant. Thus, crushing and grinding may become the most costly part of gold ore processing. It may, in fact, represent 50% to 70% of a plant's operating costs (Michaelis, 1989). The increasing significance of refractory gold will require even more cost-efficient comminution of ultrafine sulfides and/or native gold. Transitional ore zones with semi refractory gold may respond to direct leaching if better particle fracturing is being achieved (Baum, 1991, 1993a). Many oxide ores have been left in the ground because they were unsuitable for heap leaching since conventional comminution could not facilitate economic gold extraction. Also, the costs of conventional bal1 mill operations did not permit the recovery of gold from many ultrafine, low-grade refractory ores. As shown by Marsden et al. (1993), the trend to treat ores with progressively lower grades will involve power-and leach-efficient grinding applications. Our current laboratory work shows that high-pressure grinding roll (HPGR) Polycom grinding may enable many mining companies to add large amounts of these "non-leachable" ores to their current heap or mill leach feeds. This finding may dramatically change the economics of many oxide gold ore operations and may add significant reserves to ores amenable to direct cyanidation.

Jan 1, 1994

By Murray Hughes, Neil Brown, John Carran

"A control system architecture has been developed using the Ward-Mellor structured analysis techniques for real-time applications. This approach has produced several advantages over traditional control system implementation methods including:•,partitioning of the control system into discrete control functions.•,easy identification of the interaction between individual control functions and the rest of the system including the impact of changes at the control system boundary (i.e. additional inputs or outputs).•,simplified control software testing.•,a closed loop design, implementation and documentation process.This paper describes a generic control application in which the process specification and control system design are logically linked. Both components are used by process engineers for on-going development.IntroductionAluminium is reduced from alumina in multiple electrochemical semi-batch reactors. Raw material additions and molten metal withdrawal are made at discrete intervals ranging from seconds to days. The electrolytic reduction process is continuous, despite the semi-batch nature of the material inputs and outputs. The chemical and physical processes that occur within each reactor are complex and interdependent, therefore simple methods used for the control of many chemical processes are impractical. The process control system is required to optimise operating efficiencies within the safe operating zone.The process control of aluminium reduction cells is heavily biased towards calculation of process variables with relatively few measured sensors. Each cell is controlled independently of the other cells, although changes to process conditions and raw material . quality will affect all cells. The process responds relatively slowly and with significant time lags. Measurements and process variable calculations occur each second, however the accuracy and precision of actuator response and sensor sampling are measured 111 milliseconds. Time-based scheduling is a significant component of reduction cell control."

Jan 1, 1994

By King D, Dickinson S. B, Matheson R. S

Commencing in 1956, Rio TInto Australian Exploration Pty Limited in association with Electrolytic Zinc Co of Australasia, Limited, has been carrying out a mineral prospecting program in North-West Tasmania over an area of about 4000 square miles.The program has comprised extensive airborne geophysical surveys, detailed geological mapping, ground geophysical and geochemical investigations. Out of the wealth of new data, and the examination of previous records, has emerged a new structural concept of regional ore control and distribution in North-West Tasmania. This roncept stems from the discovery of an ancient 'fossil' rift valley (graben), named the Owen Rift Valley, along which are located the major mines of the area and numerous well-known prospects. The known mines and prospects from north to south include Mt Bischoff (tin); the Pinnacles (zinc, lead, ropper); the Chester (pyrites); Rosebery-Hercules (lead, zinc, ropper, silver, gold); Mt Tyndall (lead, ropper, zinc); Comstock and Tasman (copper, lead, zinc); Mt Lyell (copper, pyrites, gold); Mt Jukes and Mt Darwin (ropper). The identification of the West Coast (Owen Conglomerate) Range as a fossil rift valley is due to Or B Campana, who carried out extensive geological mapping and interpretation work, and who, with S B Dickinson, are the senior authors of this paper.S B Dickinson, who introduced B Campana to the geological problems of West Tasmania, had previously investigated the Mt Lyell and Rosebery mining fIeld, to which reference is made in this work.D King assisted in the regional mapping and in providing numerous data on the mineral distribution of the area.R S Matheson rontributed to the fmdings on ore emplacement and rontrol in the discussions held on this subject. They are accordingly included as joint authors of this paper.Credit is also due to E McCarthy, who interpreted the geophysical results, and to J H Rattigan, who compiled the preliminary geological maps from published documents and by photo-geological methods.G Hall and V H Cottle, of the Electrolytic Zinc Co in Rosebery, provided invaluable geological data and suggestions in the course of the survey, and made a constructive criticism of the manuscript of this work. The airborne geophysical survey carried out by the Adastra-Hunting Geophysics Ltd company, furnished useful data which substantiated many of the fIndings on the stratigraphic and structural relationship. The Mines Department of Tasmania and S W Carey, Professor of Geology at the University of Tasmania, were instrumental in initiating the regional survey and provided the published and unpublished geological literature on the area.The authors also wish to acknowledge the invaluable assistance received from the Mt Lyell Mining and Railway Co in Queenstown, which made available the more recent geological and mining documents rompiled by M L Wade and M Solomon.

Jan 1, 1994

By Harlan L. Kebel

Gypsum, the dihydrate form of calcium sulfate, has a history of usefulness to man dating back several thousand years, and a worldwide industry has been built on the mining and processing of this versatile industrial mineral. However, anhydrite, the other prin¬cipal calcium sulfate mineral, has very limited use, so much so that separate statistics for it are not always kept, but are usually included with those for gypsum. Although often found in close association, the two minerals have important chemical differences in that anhydrite is the anhy¬drous form of calcium sulfate (CaSO4) whereas gypsum is the dihydrate (CaSo4.2H20). These two molecules of combined water result in significant differences in hardness, density, and solubility of the two minerals. Of most importance, however, is the difference in thermal properties wherein gypsum, upon the application of a modest amount of heat, can be converted to the hemihydrate of calcium sulfate (CaSO4 '21H20) or plaster of paris, an intermediate product upon which is based over 90% of the value of all calcium sulfate end products. Anhydrite, on the other hand, is inert at these temperatures and its uses have been limited to only those few cases where calcium sulfate in the anhydrous form may have an advan¬tage. The earliest known use of gypsum plaster dates back some 5000 years to the time of the Pharaohs of Egypt who had discovered that gypsum rock, when exposed to fire, broke down into a powder which, when mixed with water, would form a putty that could be plastered on a rough mud brick or stone wall to make a smooth finish. It was used down through the centuries in a limited way for ornamental purposes, but did not achieve wide acceptance because of the quick (25 to 30 min) setting or hardening time which made it difficult to use. The first real understanding of gypsum chemistry was developed in France about 1755, and the gradual growth of its present utilization dates from that time. In the United States, the first utilization of gypsum was to grind it to a fine material for use as a soil conditioner at about the time of the Revolutionary War, and the term land plaster for ground gypsum was coined and has remained in use. Another cementitious material-lime or calcium oxide-had become the usual plastering material, but by about 1870 a method for retarding the set of gypsum plaster was discovered; today it has almost completely replaced lime as a plastering material. In recent years, gypsum products sold in the United States have reached a total valuation of approximately $2 Gpy as illustrated in [Table 1].

Jan 1, 1994

By R. A. Plumbridge

The Honourable Mr Molefe, Premier of the North- West Province; Or Scot-Russel, Chairman of the CMMI's XV Congress; Mr Loton, Chairman of the CMMI; distinguished guests, ladies and gentlemen. At the outset may I express my sincere appreciation to the organisers of this Congress for their kind invitation to me to participate in the plenary session. May I also thank the CMMI for inviting me to be their fifth distinguished lecturer. This is a signal honour and one which is sincerely appreciated by my Group and myself. The subject of gold is a very emotive one. It conjures up different images in the minds of a wide variety of people. For many of us it is very simply the ultimate metal. In ancient times gold was sought after and treasured; it was the chosen metal for adornment and many of the best preserved artefacts of that time were hand-fashioned from gold which had been won by primitive mining techniques. Gold's rarity and its value was recognised by those who fashioned the earliest gold coins thus underlining gold's special place as a store of value.

Jan 1, 1994

By Mukesh Jain

The liquor from potroom wet scrubbers is treated with lime to precipitate the soluble fluorides. The solids after filtration, referred to as scrubber mud, contain in addition to calcium fluoride, alumina, carbon, tars including polyaromatic hydrocarbons (PAH), cryolite and pachnolite and are considered hazardous. This communication deals with the pilot plant scale calcination of scrubber mud with a rotary kiln to obtain non-hazardous fluoride raw materials. Air classification was performed to separate the mudinto aluminarich andcalcium fluoride rich fractions which were then calcined. With proper control of calcination parameters and addition of lime, the carbon and tars were destroyed and hydrogen fluoride emissions were controlled. The calcined products could be used in the steel indusny as a fluxing agent or as a substitute for fluorspar in the production of aluminum fluoride.

Jan 1, 1994

By J. M. Goris

Cable bolt supports are becoming an important ground control technique in underground mines in the United States and Canada. They show great versatility and are adaptable for use with many mining techniques, they have high load-carrying capacities, they can be installed in small areas with low roots, and they are cost effective. Investigators in a number of research institutes in North America have conducted studies to assess the material and support properties of cable bolts, evaluate their support capabilities under various mining conditions, and provide design criteria for using cable bolt supports as roof control systems under varying mining conditions. While conducting these studies, personnel have collected important information on the history, application, performance, and economics of these supports. This U.S. Bureau of Mines report documents this information so that ground control personnel unfamiliar with cable bolt supports can gain an understanding and appreciation of their use. A comprehensive bibliography of technical information on cable bolt supports was selected by the authors and is also presented.

Jan 1, 1994

By Corbett GJ, Leach TM

The Nena Cu-Au high sulphidation deposit has formed within the Frieda River Intrusive Complex in association with a major dilatant structure. Multiple intermediate intrusives of Miocene age are localised by a splay (Frieda Fault) of the Fiak-Leonard-Schultz Thrust, a several hundred kilometre long structure, formed parallel to the accretionary prism of northern Papua New Guinea.The high sulphidation systems including Nena, crop out as narrow silica-alunite ridges extending for up to 5-6km in length within a dilational structural environment. Alteration at Mena exhibits two phases of hydro-thermal activity: an initial stage, inferred to be volatile-rich, which has produced zoned alteration; and a later phase, postulated to have been a liquid-dominated fluid, which has brecciated earlier alteration zones and deposited gangue phases as well as Cu/Au-bearinq sulphides in open spaces.

Jan 1, 1994

By Denni Hoffmann

"Banded iron formation rocks associated with massive sulfide lenses in the Broken Hill Pb-Zn-Cu-Ag deposit in the Namaqualand Metamorphic Complex, South Africa, were investigated with respect to the geochemistry of manganiferous silicate-rich bands. Two common varieties of these are: amphibole- and garnet-rich iron formation bands. The results reveal that the former are enriched in Fe, Mg, Cu, Co and S. The garnet-rich bands are enriched in Mn, Ca, P, Pb and Ba with significant detrital contamination of Ti, AI, Zr, Cr, Y, V, Ni and Nd.The silicate-rich bands have compositions, in terms of, Si/AI, SilFe, FelMn, LalCe and Co/Zn, comparable to submarine chemical sediments which precipitated from hydrothermal fluids. The garnetand amphibole-rich bands are interpreted as ""evolved"" and ""immature"" hydrothermal sediments, respectively. The latter resulted from rapid precipitation after exhalation, whereas the former had a longer residence within sea water. The silicate-rich bands both exhibit increasing Mn/(Mn+Fe) fractions, which are consistent with a variation expected from proximal to distal depositional settings. The prevalence of garnet-rich bands over amphibole-rich bands is interpreted as the result of injection of hydrothermal fluids from a single vent situated along the northwest margin of the Broken Hill deposit."

Jan 1, 1994

By Mark D. Hannington

Seafloor polymetallic sulfides have been found in diverse volcanic and tectonic settings on the ocean floor at water depths ranging from 3700 meters to <1500 meters. More than 100 occurrences of hydrothermal mineralization have been documented (including Fe-oxide deposits, Mn-crusts, metalliferous sediments, and massive sulfides), but high-temperature hydrothermal activity and large accumulations of polymetallic sulfides are known at fewer than 20 different sites. Chemical analyses of samples from these deposits indicate that they contain important concentrations of Cu, Zn, Ag, and Au, comparable to those of massive sulfide deposits on land. However, the lack of sufficient data concerning the distribution, size, and bulk composition of seafloor deposits precludes a meaningful assessment of their resource potential.

Jan 1, 1994

By G. G. Barbante

Copper anode slimes are a valuable source of the precious metals, and selenium and tellurium. They are mineralogically complex and this has led to a great variety of process flowsheets for treating them. The traditional pyrometallurgical method utilises oxidation in a reverberatory furnace, but has numerous shortcomings. Recently deep-bath intensive smelting methods have been developed for use in the larger refineries. Despite these process advances, the thermodynamics of the reactions involved remains poorly understood. An initial description of the thermodynamics of slimes smelting is presented, but is severely limited by a lack of basic data. It is shown that slimes smelting is superficially similar to copper converting, but has many unique features. More basic thermodynamic data on selenium-based systems are needed before the process model presented can be further refined, and work in this direction has already commenced.

Jan 1, 1994

By J. R. Bhamidipati, Nagy EI-Kaddah

"Over the years, mathematical modeling has been established as a viable tool for design and analysis of melting and solidification processes. Modeling of electromagnetic casting and melting systems involves three coupled problems -- determination of the containment field, the shape of the meniscus, and the temperature field -- which have to be solved simultaneously. One of the difficulties in numerical simulation of these systems is in defining and gridding the solution domain as the meniscus shape of the liquid region is not known a priori. This paper describes a methodology for solving these coupled problems in a two-dimensional electromagnetic containment field. This method is based on the solution of the electromagnetic, free surface dynamic, and heat transfer equations in a fixed domain in computational space by mapping the physical space into an invariant computational space during the search for the equilibrium shape using a variable non-orthogonal coordinate transformation. This approach, also, eliminates the need for regridding the liquid and solid regions during phase change. This methodology is demonstrated for two electromagnetic confinement systems -- the Magnetic Suspension Melting process and the electromagnetic casting of aluminum. The model predictions are in good agreement with available data for these systems. It is suggested that the methodology presented here is likely to provide a useful tool in the design, analysis, and optimization of electromagnetic confinement systems. IntroductionDuring the past decade, mathematical modeling has emerged as a viable tool for the design, analysis, and optimization of casting and melting processes /1-2/. It is generally recognized that the usefulness of modeling to study the interplay between the various process parameters without resorting to extensive experimentation relies heavily on accurate representation of the physical phenomena in these systems. In modeling electromagnetic confinement casting and melting systems, it is important that the model address all aspects of electromagnetic field interaction with the metal, if accurate predictions are to be obtained /3/. The electromagnetic field affects the heat transfer phenomena primarily through joule heating. In addition, the electromagnetic forces play a key role in heat redistribution in the molten pool via melt stirring, and, in confinement systems, support the molten metal pool."

Jan 1, 1994

Geophysical methods are useful non-invasive means of collecting subsurface information on the environmental impacts of resource developments. Techniques such as seismic refraction, ground probing radar and magnetics are well established tools for environmental studies of waste disposal sites. Repeat resistivity surveys, gravity surveys, and infrared or multispectral remote sensing hold great promise for monitoring environmental changes. Examples from New Zealand include geothermal field monitoring, which may involve the use of geophysics for .detecting changes of surface thermal activity, hydrothermal eruptions, induced earthquakes, contamination or depletion of shallow groundwater, and subsurface fluid recharge. Other examples include resistivity monitoring of contained effluent disposal ponds, tailings dams and landfills. Experience has shown that care is necessary to identify the natural variability of the parameter measured before drawing conclusions regarding an observed change.

Jan 1, 1994

By Timothy J. Rohrbacher

This report presents results from an ongoing U.S. Bureau of Mines study defining domestic coal reserves. Examinations of five 7 ½ -minute central Appalachian quadrangles have been completed to date. Only 26.4%, 5.0%, 6.5%, 8.2%, and 4.2% at the coal resources remaining in the Matewan, Boltsfork, and Hoskinston, KY; Vansant, VA; and Beckley, WV quadrangles, respectively, constitute economically recoverable reserves. An evaluation of the coal mining industry&apos;s impact on the economy of Pike County, KY, wherein the Matewan quadrangle is located, was also completed in order to provide a basic understanding of the influence of coal mining on the local economy. Results show that coal mining is the only major income producing industry in Pike County, accounting for about 46% of the county&apos;s income, and 21% of the total available employment, in the base year 1990. If similar results are found in subsequent investigations, a strong argument can be made that traditional coal producing regions may soon be experiencing resource depletion problems far greater and much sooner than previously thought. This will affect not only the coal industry but, given the obvious dependence of Pike County&apos;s economy on its coal mining industry, the entire social and economic infrastructure of large areas.

Jan 1, 1994