Search Documents

By Lam. E. K., J. W. Jarvi, B. P. Bharadwaj

"The Rabbit Lake Operation is located in Northern Saskatchewan on the western shore of Wollaston Lake approximately 800 km north of Saskatoon, Saskatchewan.The Operation is owned by a joint venture of Cameco Corporation and Uranerz Exploration and Mining Limited. Cameco is the operator.The Mill started production in June 1975 under the ownership of Gulf Minerals Canada Limited and over the past twenty years has increased the rated production capacity to over twice the original design.The Mill was originally designed to process 485,000 tonnes per year of ore with an annual production of 2.0 million kg of U308 (yellowcake). During the past ten years changes in ore sources and process modifications have led to increased milling capacity and production targets. The Mill has treated a total of 8.6 million tonnes of ore and produced over 40 million kg of U308 in the twenty year period, despite the shutdown and cutbacks in operating time since 1989.The 1995 tonnage throughput was 206,000 tonnes per year. Annual production though has risen to 3.6 million kg of yellowcake despite the departure from full-time to half-time operation in 1991 (7 up-7 down). The forecast for the coming years will see tonnage rising from 300,000 to 570,000 tonnes, production of 4.5 to 5.4 million kg of yellowcake and an anticipated return in the year 1998 to full time operation.This paper will give a brief history of the Mill and focus on the present flowsheet and recent improvements to the process."

Jan 1, 1996

Current scrubber capacities vary from 1.89 to 4.72 m3/s (4,000 to 10,000 cfm), and there is interest in using scrubbers with capacities up to 6.61 m3/s (14,000 cfm). This paper describes research to compare the effectiveness of blowing and exhausting face ventilation systems using high-capacity scrubbers with flows up to 6.61 m3/s. Tests were conducted in a surface ventilation gallery with exhaust and blowing systems operating under similar conditions. The mining machine was equipped with a machine-mounted scrubber. Methane gas was released at constant flow at the mining face and measured at several face locations. Effectiveness of exhausting and blowing systems was compared by determining average face methane concentrations. For each operating condition tested, blowing ventilation was more effective than exhausting for controlling face methane levels. Raising scrubber flow to 6.61 m3/s reduced methane levels for both blowing and exhausting systems.

Jan 1, 1996

By Richard E. Gray

Subsidence due to coal mining is poorly understood by non-specialists. This has led to numerous misconceptions and myths based on limited observations and lack of knowledge. The three most common are: 1. Mine maps are inaccurate. 2. Deep mines are not a problem. 3. If no subsidence has occurred for many years after mining, there is no risk of future subsidence. Maps are important during mining and most are carefully prepared. Future use to evaluate conditions at mine level often includes drilling to confirm what the map shows. Usually, little or no effort is made to tie the surface survey of the property to the mine survey, to conduct a well designed drilling program to confirm the mine map, or to drill test borings vertically. When a mine entry is encountered rather than a coal pillar, or vice versa, and conditions at mine level appear different than anticipated, the first reaction is the mine map is inaccurate. The idea of a safe depth from subsidence is often based on the false premise that mining results in sufficient breakup of the overlying rock strata that bulking compensates for the coal extracted. The safe depth idea first appeared in the literature about 1880 and remained prevalent well into this century. Sadly, it is still encountered. The modern understanding of fragmentation of the immediate mine roof with the overlying beds sagging down on the broken roof rock was first described in 1900. With full extraction mining, either longwall or retreat room and pillar, surface subsidence occurs regardless of the depth of the mine. Subsidence over longwall mines at depths of 2000 feet can be 90 percent of the mined seam thickness. Numerous studies of undermined sites conclude that mining occurred many years ago and since no subsidence has occurred, there is no risk of future movement. This is true if sufficient coal pillars have been left to support the overlying strata. However, every year subsidence occurs over mines that have been closed for 100 years or more. In a study of subsidence incidents over the Pittsburgh Coal, the senior authors found that 50 percent of the incidents occurred above mines that had been closed for at least 50 years and 10 percent over mines closed for at least 80 years.

Jan 1, 1996

By William Van Impe

A most renewing and promissing soil displacement screw pile is called the O-pile. The O-screw pile is a soil displacement auger pile based on a screwing in - screwing out procedure. The displacement auger head consists of a discontinuously diameter - increasing steel tip, on top of which the continuous screw flange with variable pitch is mounted. The soil displacement is kinematically ensured by downwardly oriented slots mounted on the auger head at different well chosen locations on the flanges. This leads to a very efficient lower energy screwing-in sequence of the pile and consequently to a high penetration rate. A test loading program of instrumented O-piles has been carried out in order to evaluate the load settlement behaviour, the shaft and tip capacity of the O-pile, including its specific installation parameters.

Jan 1, 1996

By Donald D

A number of standard tests are conventionally carried out to characterise strength properties of rock. The values of the parameters obtained are often affected by planes of weakness or defects in rock structure. For the purpose of mine design, the range in values or the class of the strength (obtained from a number of tests) is generally more important than a precise value (obtained from a single or limited number of tests). Research has been conducted to establish a relationship between an indentation index and the strength of the intact rock material from the Eastern Goldfields of Western Australia. The Tamrock Raise Boring Index (RB-i) test, which is quick and easy to perform, was selected as the indentation test. The results show that, for heterogeneous, strong to very strong rock, there is a good correlation between the indentation index and the uniaxial compressive strength and tensile strength.

Jan 1, 1996

By Ralph Harris, Xia Qi, Frank Komsic

"Gold cyanidation kinetics which are often limited in commercial operations by the rate of oxygen dissolution from gas bubbles into the slurry, are discussed. Emerging technologies for improving the rate of oxygen dissolution are compared and the gas efficiency, energy use and operating performance of inverted cones and a device based on a jet diffuser are examined. The effect of solids loading is also reviewed and a relationship between operating parameters and the kilograms oxygen dissolved per kilowatt-hour is presented.Inverted cones are shown to create slurry settling problems at high gas flow rates and surface tension lowering agents are shown not to greatly improve the overall rates of oxygen dissolution.The novel jet diffuser technology operates at a range of gas to liquid ratios that improves its energy use over conventional technology and the performance of a number of designs are discussed.Gas efficiencies as high as 35% were observed with the novel diffusers at 40 cm diffuser immersion and are expected to increase at greater immersions. Energy use of 1.8 kg 02 I kWh were estimated for prototype full size diffusers operating at 100 cm immersion. Energy use of 3.S kg 02 /kWh is conservatively expected at 600 cm immersion.IntroductionGold ExtractionGold that can not be recovered by gravity separation can be recovered by either the Merrill-Crow process or the newer carbon in pulp (CIP) or carbon in leach (CIL) processes 1. Reductions in operating costs and improvements in gold recovery are central mill operating strategies. The present paper examines the potential for improvement that can be achieved in the gold cyanidation step of gold recovery. This paper introduces a number of emerging technologies and provides a basis for comparison of the performance. It shows that the basis for comparison of a particular technology depends on the type of gold extraction circuit employed and the type of reactants employed."

Jan 1, 1996

By D. Jean Hutchinson, Mark Diederichs

"Cable bolts are an important support component in modern underground mines. If an optimized cable bolt system is to be achieved, it is insufficient to focus on cable bolt layout design or on cable bolt installation in isolation. Cable bolt support, like all engineered systems, requires a holistic approach, encompassing integrated elements of design, implementation and verification. The “Cable bolting Cycle” described in this paper incorporates these components along with related tools and procedures which should be used together to ensure effective and efficient cable bolt support.Design involves the consideration of demand, capacity and constraints as outlined in this paper. The demands imposed on the sup-port system by the rock mass response to excavation under the combined action of stress and gravity must be matched to the capacity of the cable bolt array. The cable bolt system capacity is a function of the component strengths of the steel strand and the bond (load transfer) and by the deformation response and retention characteristics of the system. The design is bounded by operational and economic constraints.Implementation of the cable bolt array can then proceed and must include appropriate protocols of communication, training and quality control, in addition to both general and site specific installation procedures. Implementation will be discussed as the sum of these components.Implementation of the cable bolt array can then proceed and must include appropriate protocols of communication, training and quality control, in addition to both general and site specific installation procedures. Implementation will be discussed as the sum of these components.The information presented in this paper represents a very abbreviated version of much broader concepts, procedures and design charts, presented in a practical cable bolting handbook by Hutchinson and Diederichs (1996)."

Jan 1, 1996

By Gole MJ

The Goodyear nickel prospect is located 45 km southeast of Kalgoorlie (31.04¦S, 121.80¦E) near the eastern boundary of Hampton Area - East Location 45 (Figure 1). Nickel mineralisation was discovered on the Goodyear prospect in March 1996 when a reverse circulation drillhole (GYC5), initially drilled in December 1995, was deepened to meet a minimum footwall penetration requirement of 20 in that had been set for the drill program. Approximately 3 in of sulphides averaging 4.9 per cent nickel was intersected from 296 metres down-hole, this being within 2 in of the first end-of-hole. Hole GYC5 was part of an eight hole drilling program undertaken by Titan Resources in late-1995. This program was designed to test whether nickel mineralisation in the Dunlop prospect, discovered by the Western Mining Corporation - BHP Camylia Joint Venture immediately east of the East Location 45 boundary, continued across the tenement boundary. The area targeted by the initial drill program had been explored by Western Mining Corporation in the mid-1980s using extensive surface sampling and a drilling program that included 17 RAB and percussion drillholes. None of these holes intersected nickel Mineralisation.\

Jan 1, 1996

A model was developed to facilitate secondary tailgate support selection based on analysis of over 100 case studies, compiled from two different surveys of operating longwall coal mines in the United States. The ALPS (Analysis of Longwall Pillar Stability) program was used to determine adequacy of pillar design for the successful longwall case histories. A relationship was developed between the secondary support density necessary to maintain a stable tailgate entry during mining and the CMRR (Coal Mine Roof Rating). This relationship defines the lower bound of secondary support density currently used in longwall mines. The model used only successful tailgate case history data, with adequate ALPS SF according to the CMRR for each case. This model facilitates mine design by predicting secondary support density required for a tailgate entry depending on the ALPS SF and CMRR, which can result in significant economic benefits.

Jan 1, 1996

By Shoukun Wei, Cong Wang, Lin Cheng, Zhiyu Qiao, Jingkui Liang, Weidong Zhuang

"The subsolidus phase relations in the Sm2O3-CeO2-CuO ternary system sintered at 1000°C in air have been investigated by X-ray powder diffraction. The system can be divided into two ternary phase regions and three binary phase regions. Solid solution Sm2-xCexCuO4-y is the only ternary phase in the system. The maximum solid solubility was confirmed to be x = 0.2. The crystal structure, oxygen content and superconductivity of the solid solution Sm2-xCexCuO4-y have been investigated.I. INTRODUCTIONAfter the first discovery of the superconducting ceramic system La-Ba -Cu-O[l] with Tc = 30 to 40K, other families of cuprate-based ceramics have been synthesized with higher critical temperature. These oxides include the R-Ba-Cu-O (R: rare earth) systems (Tc=90K or so)[2,3], the Pb-Sr-(R,Ca)-Cu-O systems (T c = 50 to 100K), the Bi-Sr-Ca-Cu-O systems (Tc=80 to 105K)[4], the T1-Ba-Ca-Cu-O systems (Tc=85 to 125K)[5], the Hg-Ba-Ca-Cu-O systems (Tc=90 to 150K)[6,7], and some others. The improvement of Tc is very rapid. The measurement of the Hall and Seebeck coefficients shows that they all are p-type superconductors. In 1989, Tokura et al.[8] discovered the superconductors R2_XCexCU04_y(R = Nd, Pr, Sm) with Tc=20 to 24K (onset) and found that the charge carrier is electron in contrast to their hole doped counterparts. This discovery increases the fundamental understanding of the cuprate-based superconductors by comparing their characteristics and mechanisms to those of the p-type superconductors.One of the outstanding features of these n-type superconductors is the difficulty in obtaining samples in good charactors, such as the difficulty in obtaining zero resistivity state in single crystal or bulk samples; the semi-conductivity of bulk samples in ordinary state (opposite to the superconducting state) and a reducing reaction involved before the superconductivity has been found[9]. Therefore, it is necessary to optimize the sample preparation of the n-type superconductors. All the n-type superconductors have been found· considerable solid solubility. The compositional variations play a governing role in the carrier doping of the superconducting phases. Also, it is vital to the ceramic processing of superconductors to identify the compatible phases in the phase diagram. Finally, there is always the possibility of finding additional compounds, both superconducting and non-superconducting, in an unexplored system."

Jan 1, 1996

By A. Verghese Chummar

The paper presents a field study where the effect of negative drag caused the failure of a pile foundation system. Utilising the field observations the probable negative drag that acted on the piles is worked which gives an insight into the effect of negative drag on deep foundations.

Jan 1, 1996

By C. Pereira

Spent nuclear fuel (SNF) can be treated in a molten salt electro refiner for conversion into metal and mineral waste fonns for geologic disposal. The fuel is dissolved in molten chloride salt. Non-transuranic fission products in the molten salt are ion-exchanged into zeolite A, which is subsequently mixed with glass and consolidated. Zeolite was found to be effective in removing fission product cations from the molten salt. Breakthrough of cesium and the alkaline earths occurred more rapidly than was observed for the rare earths. The effluent composition as a function of time is presented, as well as results for the distribution of fission products along the length of the column. Effects of temperature and salt flow rate are also discussed.

Jan 1, 1996

By S. S. Peng

High horizontal stress has been well recognized as a significant factor in roof control. It can adversely affect roof stability if the panel is designed improperly. Mining experience has shown that it can cause a cutter roof. The effects of high horizontal stress on roof stability depend on many factors such as magnitude and direction of the maximum principal horizontal stress, ratio of the maximum to minimum principal horizontal stress, structure and mechanical properties of the immediate roof and mining sequence. However, little is known about the intrinsic mechanism of high horizontal stress effect on roof stability except some conceptual explanations. In order to design a stable entry, the redistribution and concentration of high horizontal stress around the openings must be fully understood. Using the 3-D finite element analysis technique, this paper presents the redistribution and concentration of high horizontal stress field for a three-entry system with different orientations of horizontal stress. Based on the horizontal stress redistribution, possible roof failure for different orientations of horizontal stress is analyzed.

Jan 1, 1996

By Catharine E. G. Farrow, David H. Watkinson

The Ni-rich Epidote Zone of the Fraser Mine at Sudbury is characterized by alteration assemblages rich in epidote, actinolite and magnetite which are roughly concentrically zoned and up to hundreds of meters in length. These zones form discrete areas within the igneous Footwall Breccia below the Sudbury Igneous Complex. The assemblages grade from epidotized Footwall Breccia matrix,through actinolite-bearing rocks with few vestiges of original Footwall Breccia textures, into the most intensely altered rock, a magnetite-rich facies. Pentlandite, pyrrhotite and pyrite are the dominant sulfdeminerals; chalcopyrite is minor. The strongest geochemical differences compared to original Footwall Breccia occur where epidote and actinolite dominate the alteration assemblage (EPDZact facies). The most intense alteration facies are typifed by low Cu/(Cu+Ni) values of <0.1. Strong positive correlations exist between Ni and Co, Cu and Au, and among Ir, Os, Ru and Rh. Chondrite-normalized Ni - PGE -Au - Cu plots display an overall increase in all elements from the least to the most intensely altered facies except for Au and Cu. As the proportion of actinolite increases in the EPDZact facies, the chondrite-normalized profles fatten considerably due to low Au and Cu contents. Abundances of Ni, Ir, Ru and Rhalmost ubiquitously increase with degree of alteration. In contrast, Cu, Zn, Ag and Au contents are low in almost all facies. It is suggested that saline hydrothermal fluids moved through the Epidote Zone formation and became more oxidized as they reacted with the Footwall Breccia and with footwall units, including ultramafic rocks. As this trend continued, magnetite-rich zones eventually developed. The occurrence of calcite locally in these magnetite-rich zones suggests that the pH of the fluid increased, causing Cu solubility to drop as activity in the hydrothermal system waned. Sudden changes in fluid composition such as this may have been due to an influx of fluid from bounding ultramafic rocks. Hydrothermal activity was focused along the margins of footwall ultramafic units. Individual hydrother-mal cells may have formed in the Footwall Breccia along pre-existing structures or sulfde concentrations. Metals may have been scavenged from sulfide-bearing Footwall Breccia and possibly Sublayer rocks. Nickel and some PGE were deposited in the Epidote Zone, whereas Cu, Au and Ag continued out-ward into the footwall where they were deposited as Cu-rich footwall veins. Copyright © 1996 Canadian Institute of Mining, Metallurgy and Petroleum.

Jan 1, 1996

By M. K. Larson

The U.S. Bureau of Mines and Cyprus Shoshone Coal Corp. conducted a study of deformation mechanisms in strata around a longwall gate road system at two sites in an underground coal mine near Ham, WY. Of particular interest was timedependent (on the order of several months) roof deformation. Strata above and below the coal seam are very weak, carbonaceous mudstones that have cohesionless planes of weakness oriented along bedding, which dips approximately 8° to 16° at N 49° E. An extensive array of instrumented roof bolts, roof extensometers, and biaxial stressmeters were installed during development mining at these two sites under variable depth of cover [I83 to 335 m (600 to 1,100 ft)], seam dip (10° to 16°), and top coal thickness [estimated to be 0.30 to 0.61 m (1 to 2 ft) on the downdip side of the entry]. Bolt load and roof deformation histories during the entry development periods were compared. Bolt loads at site 2 were less than those at site 1, which is consistent with the amount of overburden. Deformation magnitudes at site 2 were similar to those at site 1, but deformation rates were approximately 44% greater and nearly constant over time, whereas the deformation rates at site 1 decreased exponentially over time. Also, most deformation occurred above the bolt horizon at site two, but extensometer measurements at site 1 showed that a significant amount of deformation occurred within the bolt horizon. The most significant factor that influenced bolt tension and timedependent strata deformation was strength and Young&apos;s modulus of the strata. Finite-difference models support this conclusion.

Jan 1, 1996

By : D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By C. Cho

One problem with the application of neural networks to the multivariable control of mineral and extractive processing is deciding whether and how best to use them. The objective was to compare neural network control to more conventional strategies and find any advantages in terms of set point tracking, rise time, settling time, disturbance rejection, and other criteria. The procedure was to develop neural network controllers using both historic plant data and simulation models. We tried various neural network control patterns including both inverse and direct neural network plant models. These were compared to state space controllers that were, by nature, linear. For grinding and leaching circuits, a nonlinear neural network-based model predictive control strategy was superior to a state space-based linear quadratic Gaussian controller. We also learned the importance of incorporating state space into neural networks by making them recurrent--feeding certain output state variables into input nodes in the neural network. We concluded that neural network controllers can have better disturbance rejection, set point tracking, rise time, settling time, lower set point overshoot, and can be more foolproof and easy to implement in complex, multivariable plants.

Jan 1, 1996

By J. Matos e Silva

The paper refers two examples of structures located in seismic areas (Cases 1 and 2). The first one (Case 1) is the Torroal Bridge, located about 100 Km South of Lisbon, in the road Troia-Grandola. The horizontal loads due to the seismic actions were mainly carried by an anchor curtain connected, to the abutments, by reinforced concrete struts-ties. For the some purpose diaphragm walls were also placed under the pile caps of the column foundations. The second one (Case 2) refers to a building located about 50 Km South of Lisbon, at Sesimbra, near a cliff. To reduce the horizontal displacements of the structure due to seismic actions, in order to prevent the endangering of the cliff stability, an anchor curtain was adopted and connected, to the structure, by prestressed anchors.

Jan 1, 1996

By Ree Llewellyn

"It has been estimated conservatively that the costs of wear damage and friction in the Canadian mining and mineral processing industry amount to over one billion dollars per year. These are mainly incurred through the repair or replacement of worn parts and production losses from related equipment downtime. The selection and application of the most appropriate wear protection components and systems, can thus have a very significant influence on productivity, profitability and global competitiveness.Details are presented of the wide diversity of materials used to counteract the varied and often complex wear attack mechanisms that occur in surface mining. The majority are various forms of steels and irons with generally very high hardness. However, they also include relatively soft elastomers and polymeric products.The main characteristics and applications of the different classes are reviewed. Case studies record significant performance improvements achieved through more judicious selections. Finally, some new developments which reduce maintenance charges by substantially increasing wear component life, are described."

Jan 1, 1996

By Y. Z. Zhang

Cyanide has generated environmental concerns because of its toxicity, and it may not respond to the treatment of complex and refractory gold ores. Gold leaching by thiourea is one of the most promising substitutes of cyanide. However, the high reagent consumption has hindered thiourea from its commercial application in gold extraction. The process chemistry and mechanism of thiourea degradation has been discussed on the basis of chemical bonding theory, thermodynamics and electrochemistry in this paper. Progresses on the decreasing of thiourea consumption have been summarised. The potential application of thiourea in gold extraction has been evaluated.

Jan 1, 1996