Search Documents

By R. V. Ramani, W. Miola, R. Srikanth, S. C. Soboleski

"Dust control in high-production longwalls requires attention to operating practices and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in US longwalls. Yet, under certain conditions, 31% of the shearer operator's dust exposure can be due to support movement.Several methods have been developed for the control of shield-generated dust. But the need for better methods is apparent. In this paper, the amount of airborne, respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. Ten experiments were conducted on five longwall faces in four mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne, respirable dust concentration immediately downwind of the shield move varied between 0.12 and 1.75 mg/m3 in the five longwall faces. The mass of airborne, respirable dust gener-ated by shield movement was found to vary between 39 and 386 mg per shield move. The results from this study reveal that control of dust from longwall shields requires a combi-nation of approaches involving alternative operating prac-tices, reducing shield dust generation rate, increasing face air flow and decreasing personnel exposure.IntroductionIn 1992, longwall mining accounted for about 36% of US underground coal production, a 240% increase from a decade ago. The absolute longwall tonnages were 46 and 133 Mt (51 and 146 million st), respectively. Compared with room-and¬pillar mining systems, the longwall mining system is charac¬terized by higher recovery, enhanced safety and higher pro¬ductivity.However, personnel dust exposure on a longwall face is higher than in other types of mining. According to Mine Safety and Health Administration (MSHA) data, fewer longwalls were in continuous compliance with the applicable dust standard in 1992 than in 1989.Controlling shearer-generated dust and reduction of per-sonnel exposure to airborne dust have commanded attention in the design of longwall faces, operational practices and ventilation schemes. Studies in the United States and abroad have revealed that support-generated dust can be a major obstacle to compliance under certain conditions (Becker et al., 1989; Bradley et al., 1983; Jankowski and Organiscak, 1983; Jankowski et al., 1990; Organiscak et al., 1985)."

Dec 1, 1996

By P. A. Rossouw, G. A. Fourie

Several attempts have been made over the latter half of the twentieth century to devise a system for the classification of underground mining methods. None of these are found to be totally successful. A revised classification is suggested with three main categories being identified by reference to fill requirements, steep stopes and stratified geological environments. Methods always needing lasting mass or structure fill include methods with timber-structured stopes and those with mass-filled (or cut-and-fill) stopes. Methods associated with steep stopes are subdivided into steep-stope-specific caving and steep-stope-specific non-caving (or self-supporting) methods. Methods not in the first two categories, often used in stratified geological situations, are not necessarily restricted to stratified environments and include caving as well as non-caving varieties. This category is further divided into room-and-pillar mining, longwall and shortwall coal mining and the type of open stoping found in gold or platinum reefs comprising overhand, underhand and breast-stoping variations

Dec 1, 1996

By T. Serradj

A study has been carried out to: develop a method for routine characterisation of rock strength and drillability through the particle-size distribution of crushed or drilled rock products, defined by the Protodyakonov index; establish correlations between the Protodyakonov index, uniformity coefficient and the constant grading equations; and propose an alternative rock characterisation index to classify rock strength and drillability for the northeast region of Algeria

Dec 1, 1996

By Y. H. Cheng, D. M. Lewis, V. Castranova, M. W. Barger, J. K. H. Ma, J. Y. C. Ma, W. F. Xin

Bis-basic ethers off fluorene and fluoren-9-substituted derivatives such as tilorone have been reported to inhibit silica-induced fibrosis in rats. The potential antifibrotic potency of 2,7-bis (diethylamino) ethixy fluorine fluorenone (F-9-H.H), fluorenoxime (F-9-one), and fluorenol (F-9-ol) was F-9-axime > F-9-one ~ F-9-H,H > F-9-ol. Since the release of reactive oxygen species and growth factors from alveolar macrophages (AM) in response to silica exposure has been linked to the development of pulmonary fibrosis, the present study was carried out to determine the inhibitory effects of these compounds on rat AM activity in vitro. The following parameters were monitored: (1) cellular viability; (2) zymosan-induced respiratory burst activity (superoxide and hydrogen peroxide release, chemiluminescence, and oxygen consumption) of AM; (3) drug binding to AM; and (4) lipopolysaccharide (LPS)-stimulated interleukin- I (IL-1) release from AM. The bis-basic ethers, at 40 did not affect cell viability when incubated with AM for 30 min, but significantly inhibited zymosan-induced macrophage respiratory burst activity. The inhibitory effect of these agents was F-9-oxime > F-9-one ~F-9-H,H > F-9-ol. Binding of these drugs to AM was time and dose dependent, and exhibited the following binding affinity: F-9-oxime > F-9-one > F-9-H,H > F-9-ol. F-9- oxime was shown to inhibit LPS-stimulated IL-I release by AM in a dose-dependent manner. This inhibition of IL-1 release by AM cannot be explained as a decrease in viability. In addition, these drugs were also shown to impair human fibroblast proliferation in response to serum stimuli without impairing cell viability. These results indicate a positive correlation between drug binding to AM or other cell types and their inhibitory effects on cellular activities including oxygen consumption, superoxide release, hydrogen peroxide secretion, chemiluminescence, IL-I release, and proliferation. The ability of-these bis-basic ethers to modify AM and fibroblast functions in vitro suggests that further investigation of their reported antifibrotic potency in vivo is warranted.

Dec 1, 1996

By A. Berckmans

The key variables in the financial analysis of a mining project include the metal price and the quantities of ore and metal. In general, if the metal price drops, the cutoff grade is increased so as to increase the average grade. This causes recovered tonnages of ore and metal to drop. Discussion is presented of the development of a new method to evaluate the relationship between the cutoff grade, z, the ore tonnage above cutoff, T, and the metal quantity above cutoff, Q. Detailed information is provided on the QTz curves for lognormal and inverse gaussian (Sichel's) distributions. Both these distributions are used as models for the grades in different types of ore bodies, and they are both T-symmetric. The geometry of the QTz curves is simplified, making it easier to work out the impact of minor variation in the parameter values for each distribution

Dec 1, 1996

By R. V. Ramani, S. Shankar

"Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant (Shankar and Ramani, 1991 ). Therefore, as part of the Respirable Dust Center's ongoing research, the following three-part study was undertaken:• a study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities;• a study of the same in the Lake Lynn Laboratory Mine of the USBM with both air flow and walking by personnel causing re-entrainment; and• the mathematical modeling and computer simulation of the re-entrainment phenomenon.In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory mine are presented. Comparing the results from the two studies,it was observed that increasing the air velocity increased the rate of re-entrainment ( Shankar and Ramani, I 994a) and the rate of re-entrainment decreased with the time of exposure of the source dust to the flowing air. In addition, when the source dust was composed of particles of different sizes, the airborne dust concentrations due to re-entrainment were higher than when the source dust was composed of particles of the same size. The contribution of airborne dust concentration due to air flow was negligible compared to the contribution due to walking. IntroductionIn underground coal mines, dust is produced primarily during the process of mining and during such activities as pillar spall, loading, belt transfer and roof fall. The generated dust is entrained and then collects on surfaces through dispersion, diffusion and eventual deposition. Removal forces, such as flowing ventilation air or turbulence caused by walking and moving vehicles, can re-entrain the deposited dust (Hall, 1955). A portion of the re-entrained dust remains airborne and increases the concentration of airborne dust in mine airways.The presence of airborne coal dust in mine airways in large concentrations can be hazardous. Health effects include coal workers' pneumoconiosis (CWP) and silicosis, and it can be a nuisance affecting visibility. In addition, as is common during methane explosions, if the concentration of airborne coal dust becomes significant, there could be a coal-dust explosion (Singer, Cook and Grumer, 1972; Singer, Harris and Grumer, 1974; Edwards and Ford, 1988). Through concerned research efforts over the last decade, significantprogress has been made in reducing the airborne dust concentration in mine atmospheres. However, secondary sources, such as re-entrainment, have not been studied in-depth. It is important to understand the phenomenon of re-entrainment and its potential contribution to the airborne dust concentration in mine airways for further decreasing airborne dust hazards in mines."

Dec 1, 1996

Errors in ore reserve estimation can occur during drilling and sampling, sample preparation and analysis, geological logging and modelling, database construction, statistical or geostatistical evaluation, selection of economic parameters, selection of ore reserve method and assessment of mining constraints. Core sample recovery can be a major source of error, and it is proposed that the modelling of grade, metal accumulation and thickness should be accompanied by the modelling of core recovery (or core loss) so that for each ore block a weighted block recovery factor is obtained. This gives a good indicator of the reliability of a reserve estimate. It is suggested that a resource reliability rating (RRR) system be established to quantify what is meant by geological assurance and to combine this with an estimate of the precision of estimation as gained by geostatistical analysis. Proven and probable minable reserves would be those with an RRR better than 50% and a precision of estimation better than 20%

Dec 1, 1996

By R. L. Grayson, L. L. Probert

"A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive X-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for particles at 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of mineral particles. This paper focuses on the results for respirable quartz particles sampled from five underground coal mines across the US. Through statistical analysis of results the relationship between the fraction of surface available quartz in respirable dust samples and coal rank is established for three Pennsylvania coal seams. IntroductionThis is the last in a series of papers detailing the results of SEM/EDX-based analyses of respirable coal mine dust particles collected from field sampling. Previous papers have detailed preliminary results and the statistical validity of the methodology (Grayson, Andre, and Simonyi, 1990; Grayson, 1991). This paper presents the final results of the analysis of respirable dusts from five coal seams with a range of coal rank:• Lykens Valley seam (anthracite), eastern Pennsylvania• Brookville (A) seam (mid-vol bituminous), central Pennsylvania• Pittsburgh seam (high-vol B bituminous), western Pennsylvania• No. 6 seam (high-vol C bituminous), Illinois• Wadge seam (sub-bituminous A), ColoradoSEM/EDX-based techniques were applied to try to clarify the role of quartz as an etiologic agent in coal workers' pneumoconiosis (CWP). It was hypothesized that previous studies were hampered by the restrictions of bulk analysis techniques and that particle-level analyses were needed to answer a number of questions concerning the role of quartz in CWP and its progression.Since 1985, a large number of the respirable dust samples submitted to MSHA are analyzed for free silica (Tomb, Parobeck, and Gero, 1986). Our reasearch shows that conventional bulk analysis techniques may not give a true indication of the biologically available, or active, quartz in mine dusts. Analytical evidence indicates that respirable dust samples may contain many quartz particles that are occluded, or coated, resulting in a bulk analysis for ""free silica"" that may not be indicative of the biologically available quartz surface."

Dec 1, 1996

By M. L. Wang, S. R. Short, E. M. Daniloff, E. L. Petsonk, D. M. Mannino, G .. R. Wagner

"Background—It has been suggested that health related job selection is a major cause of the healthy worker effect, and may result in inaccurate estimates of health risks of exposures in the working environment. Improved understanding of self selection, including the role of airway hyperresponsiveness, should improve accuracy in estimating occupational risks.Methods—We evaluated symptoms of the respiratory tract, lung function, occupa¬tional and smoking histories, and airway responsiveness from a cross sectional sur¬vey of 478 underground bituminous coal miners and non-mining controls. Workers with abnormal spirometry were excluded from methacholine testing.Results—Methacholine responsiveness (= 15% decline in forced expiratory volume in one second) was associated in both miners and controls with reduced ventilatory lung function and an increased risk of respiratory symptoms. Miners with the longest duration of work at the coal face had a low prevalence of methacholine responsiveness, compared with miners who had never worked at the coal face (12% v 39%, P < 0.01). Throughout their mining careers, miners who responded to methacholine were consistently less likely to have worked in dusty jobs than miners who did not respond to methacholine.Conclusions—These results provide evidence that workers who are employed in dusty jobs are less likely than their unexposed coworkers to show increased non-specific airway responsiveness, pre-sumably as a result of health related job selection. Surveys of workers in which responsiveness data are unavailable may underestimate the effects of dust exposure on respiratory health."

Dec 1, 1996

By F. Chen, L. J. Gaydos, L. M. Demers, D. C. Kuhn, S. C. Sun

"In this report, we demonstrate that NF-KB, a ubiquitous transcription factor, plays an essential role in silica-induced inflammatory mediator production in the mouse macrophage cell line RAW 264.7. Compared to the effect of lipopolysaccharide (LPS), silica mediated a stronger activation of NF-KB p50/p50 homodimer at early phase of poststimulation. Furthermore, activation of NF-xB by silica and LPS appears to be mediated by different signal transduction pathways. Both silica and LPS increased mRNA expression in these cells for cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-a and interleukin- I a. This expression was attenuated along with the inhibition of NF-KB activation. It is well documented that exposure of alveolar macrophages to silica can initiate excessive production of inflammatory mediators and cytokines from several early response genes (1-3). At the DNA level, a common structural characteristic of these genes is the presence of one to five NF-lCB binding sequences (KB) in the 5'-flanking region (4-6). In resting cells, NF-KB is retained in the cytoplasm in an inactive form by binding to inhibitory protein known as hcBcx, hcB~. p 105 (precursor of p50) and p 100 (precursor of p52) (7-9). Upon cellular stimulation, these inhibitory proteins are proteolytically degraded or processed by certain proteases, which allows the liberated NF-KB to translocate into the nucleus as an activated form to initiate or regulate early response gene transcription by binding to its consensus element (GGGRNNYYCC)(7).In this report, we demonstrate that silica can efficiently induce NF-lCB activation in RAW 264.7 cells, and that silica displays different characteristic from LPS in the activation of NF-KB, both with respect to NF-KB subtype composition and the signal transduction pathway that leads to the activation of NF-KB. In addition, abrogation of NF-KB activation by inhibiting the protease can dramatically reduce the mRNA expression of cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-ex (TNF-o.) and interleukin-lex (IL-lex). These findings strongly suggest that NF-KB plays an essential role in silica-induced inflammatory mediator production in the monocyte/ macrophage cells."

Dec 1, 1996

By X. Chi, J. W. Griffith, C. L. Schengrund, J. Sabol

"Experiments were carried out to determine the long-term effect of instillation of 500 mg of generic bituminous, anthracite, quartz, or titanium dioxide (Ti02) dust on the composition of pulmonary surfactant. Dust was instilled in the caudal lobe of the right lungs of female pigtailed macaque monkeys (Macaca nemestrina). The composition of surfactant isolated from cell-free bronchoalveolar lavage (CF-BAL) samples obtained from right lungs (dust exposed) at various times over the following year was compared with that of surfactant isolated from CF-BAL from left lungs (dust free) . Little change was seen in the amount of surfactant-associated lipid phosphorus as a result of exposure to dust. Exposure to quartz, anthracite, or Ti02 dust induced a significant increase in the total amount of protein in the surfactant-enriched fraction. The relative amount of specific proteins was also altered: surfactant-associated protein A decreased, and the amount of the heavy and light chains of immunoglobulin molecules (identified by NHiterminal amino acid sequence analysis) increased. These changes were visible more than a year after instillation of quartz and at least 3 months after instillation of anthracite dust. Despite variation in the responses of the individual animals, the changes observed might serve as an indicator of the severity of the effect of exposure of the lung to mineral dust and/or to pathogens. IntroductionSurfactant is essential for normal pulmonary function and gas exchange. It functions to reduce surface tension and may help to prevent pulmonary edema [19] and to protect against infection [13]. The importance of surfactant to normal Jung function is illustrated by the fact that neonates lacking appropriate surfactant undergo respiratory distress and do not survive without clinical support."

Dec 1, 1996

By W. Miola, R. V. Ramaoi

"The MSHA prescribed method for the determination of quartz in airborne respirable-dust samples from underground coal mines is the P-7 method, a combination of /ow-temperature, radio-frequency ashing (LTA) and infra7 red analysis (IR). There is no prescribed procedure for quartz analysis in bulk samples of coal and host rock. Dispersive infrared (IR), Fourier-transform infrared (FTIR) and X-ray diffraction (XRD) methods are most commonly used for the analysis of quartz in powders. Several aspects of the experimental procedures, such as the preparation of the analysis sample from bulk samples, ashing techniques, scanning procedures, peak measurement location, calibration techniques, sample amounts, size consist and data interpretation, affect the results from each of the methods differently. Significant differences in analytical results obtained from X-ray diffraction (XRD) and infrared spectroscopy (IR) on the same samples are reported. All studies point to the need for reliable quartz analysis methods.In a recent research program, a procedure for preparing bulk-coal and host-rock samples for quantitative quartz analysis was developed. Further, the results from X-ray diffractometry and infrared spectroscopy for quartz content on identical samples were compared. Calibrations with pure and mixed standards were used to assess the influence of particle-size distribution, matrix and calibration on the analytical results. In this paper, several issues concerning the measurement of quartz in the samples of coal, host-rock and airborne respirable dust from mines are outlined and quantified. IntroductionThe literature on coal-mine airborne-dust control has identified a need for a better understanding of the sources, mechanisms and amounts of quartz in mine airborne respirable dust (Althouse, 1984; Jankowski, Nesbit and Kissel, 1985; Ramani 1988; Qin, 1988; Bhaskar and Xu, 1990; Bhaskar and Li, 1992; Ramani, Qin and Miola, 1991 ). To understand the quartz content in the source materials, bulk samples of coal and host rock must be analyzed. Establishing an analysis procedure for determining the quartz content in bulk-coal and host-rock samples is necessary for identifying the sources of quartz in mines; for establishing the relationships between the quartz contained in the source and in the airborne dust; and for controlling the content of quartz in the mined product and in the airborne respirable dust."

Dec 1, 1996

By F. Chen, L. J. Gaydos, D. C. Kuhn, Demersm L. M., S. C. Sun

"Summary: In this report the differential regulation of NF-KB and nitric oxide (NO) was investigated in the mouse macrophage cell line RAW 264.7 following exposure to a mineral dust (silica) and /or an endotoxin (Lipopolysaccharide, LPS). The results indicated that silica and LPS can significantly induce the activation of NF-KB as well as elicit enhanced production of NO in RAW 264.7 cells as part of an early inflammatory response mechanism. A 24-hour time-course study showed that NO release from these cells continued to increase following the initial stimulus by LPS or silica. In contrast, activation of NF-KB was maximal at 6 hours and then showed a steady decline to 24 hours. The production of NO was suppressed by protease inhibitor and antioxidant, both of which block the activation of NF-KB. Surprisingly, the use of an NO synthase inhibitor resulted in an enhancement of NF-JCB activation. These findings suggest that NO produced in macrophage cells in response to an inflammatory stimulus like silica or LPS my be linked to a negative feedback role on the activation of NF-KB. It is now accepted that nitric oxide (NO) plays a pivotal role in the inflammation response process when macrophage cells are activated by a pro-inflammatory stimulus (l). Production of NO is dependent on the activity of the enzyme nitric oxide synthase (NOS). Up until now, at least three distinct genes have been described which encode different isoforms of NOS. NOS has been cloned from a variety of different mammalian cells, including constitutive neuron NOS, constitutive endothelium NOS and inducible NOS (2). Macrophages appear to be the principal cellular source for the inducible form of NOS (iNOS) activated in response to an inflammatory producing event. The mechanisms subserving the regulation of the iNOS gene and NO production have been under intense investigation in recent years (3-5). Several binding sites for transcriptional factors have been identified in the promoter region of iNOS gene, including NF-lCB, AP-1, NF-IL6, Oct-I to cite a few (5). NF-KB appears to play a"

Dec 1, 1996

By V. Krupa, E. Lazarova

A method is proposed for the continuous calulation of a rock mass in real time while tunnelling with a TBM. Rock properties are investigated through models of the fracture stress under the disc cutters, the quasi-shear stress between the disc cutters and the specific energy of cutting under the disc cutters. Comparison of theoretical and monitored data of cutting specific energy can be used to determine theoretically the prevailing shape and size of the bulk debris. The shape and size of the chips from a given rock vary with the boring parameters. Introducing shape and volume corrections into the models of the evaluated stresses suppresses the influence of the boring regime and allows the rock properties to become dominant

Dec 1, 1996

By R. V. Ramani, J. Qin

"In this paper, the results of a research study on airborne dust transport in a full scale simulated longwall face are presented. The simulated longwall face was set up in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines to conduct experiments under controlled conditions. The controlled parameters in the experiments were the dust dispersion rate, dust size distribution, density of the dust, air velocity, and the rate of travel of the dust generating source. The analyses of the experimental results on mass concentrations, particle size distributions, and real-time respirable dust concentrations are discussed. There are definite spatio-temporal trends between the location of the shearer, the concentration at any location in the face, and the dust generation rates. The size-consist and density characteristics of the source dust, the air velocity in the face, and the air leakage into the gobs all affect the concentration. INTRODUCTIONA detailed experimental study on the characteristics of longwall dust cloud in operating longwall faces has been reported by Ramani, Qin, and Jankowski (1991). The study indicated that there are several important factors whose effects on dust transport in longwall faces need to be further investigated. In an operating longwall face, the effect of these parameters could not be easily isolated as control over the affecting parameters is not readily possible. In a simulated longwall face, however, these parameters can be controlled. Therefore, as a follow-up to the field study, a series of controlled experiments were conducted in a full scale simulated longwall face in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines [Qin, 1992]. Specific aspects which were addressed during the experimental design phase included determining the types of samples to be collected, selecting proper instruments to collect these samples, and developing detailed sampling and time-study plans to correlate the dust concentrations with face activities. Two types of dust--anthracite and bituminous--were used. Dust dispersion rate into the air as well as the source dust particle size distribution were documented. Control was exercised over both air velocity at the face and air leakage along the longwall face. During experiments, the dust source was moved to simulate the shearer movement at operating longwall faces. Detailed descriptions of the design of experiments, experimental results, and data analyses follow in the subsequent sections."

Dec 1, 1996

By R. V. Ramani, S. Shankar

"The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies.A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec.Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg!m3 (standard deviation= 0.03 mg/m3)from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0.10 mg/m3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. Jr was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed.Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining."

Dec 1, 1996

By R. V. Ramani, S. Shankar

"A convective dispersion model has been utilized to calculate the real-time airborne dust concentration in mine airways using re-entrainment as the only source term for airborne dust. It incorporates two important sources of re-entrainment in mines -- air velocity and movement of objects. The model has a sink term accounting for the deposition of particles along the airway. The model is solved using a finite difference scheme which is coded for computer. The computer model outputs airborne respirable and total dust concentrations along the airway as a function of time. The real-time and average gravimetric concentrations from several in-mine experiments were compared with the results from the simulation of the experimental conditions. This model can be used for estimating airborne dust entrainment due to air velocity, equipment movement, and persons walking. INTRODUCTIONEdwards and Ford (1988) developed a model for coal dust explosion suppression and utilized a predetermined value of threshold velocity for flowing air to pick up dust from floor. Depending on the strength of the removal forces, re-entrainment can increase the airborne dust concentration in mine airways. The most prevalent forces causing re-entrainment in mine airways are the drag and lift forces due to flowing air, and removal forces due to the movement of persons and vehicles. Shankar and Ramani (1991) have investigated the unique characteristics of the re-entrainment phenomenon in mine airways. Experiments on re-entrainment of coal dust particles were conducted in mine airways, and in a wind tunnel (Shankar and Ramani, 1994a, and 1994b). The results from the two experimental studies were found to compare well (Shankar and Ramani, 1995). There is no reported model to determine the airborne dust concentrations due to airflow or persons walking under conditions existing in mines. The present study is a part of a continuing research project in the Generic Mineral Technology Center for Respirable Dust on the spatial and temporal behavior of airborne dust in mine airways (Ramani, 1983)."

Dec 1, 1996

By M. J. Friedel, D. F. Scott, T. J. Williams

In an effort aimed at monitoring mining-induced stress changes that may influence ground failure, the US Bureau of Mines conducted a series of active 3-D seismic tomographic surveys at the Homestake (Lead, South Dakota) and Lucky Friday (Mullan, Idaho) mines. Existing rock bolts were used to mount geophones and as strike points for introducing seismic energy using a 3.6 kg sledge hammer. Travel time measurements were recorded spanning up to 160 m between drifts at several levels. The tomographic uncertainty was minimized by computing iso-velocity surfaces of constant probability based on statistics from multiple reconstructions and a threshold criteria. Periodic imaging using tomographic velocity surfaces demonstrated that temporal and spatial changes in the local stress field occurred in response to ground failure and stope advancement at a gold and silver mine, respectively. Keywords: Temporal imaging; Mine-induced stress; Seismic tomography; Geophysics

Sep 9, 1996

By M. A. Bussell, G. S. Camm

The study included lode zones at Wheal Pendarves, South Crofty and Rosevale tin mines. Fluid inclusion-containing microfractures are a common feature of the granites and typically show a preferred orientation over quite a large area. The close proximity of a dominant vein or fault controls their density and orientation. They are important pathways for fluids and provide a marker for palaeo-fluid flow. Overprinting provides a reliable representation of the evolution of the hydrothermal fluids in a vein system from early magmatic fluids to late-stage meteoric and basinal brine input. Measurement of microfracture orientation allows estimation of the regional stress regime during a specific hydrothermal event. Since micro- and macro-structures can generally be reliably correlated, these studies assist in modelling the detailed development of complex vein systems. Microfracture density is a good measure of palaeo-permeability, with implications for control of wallrock alteration. The determination of the location and density of microfractures can assist the mine geologist in identifying the location of potentially economic vein structures where macroscopic markers are absent

Aug 1, 1996

By A. H. G. Mitchell

Most, if not all, of the six recognised post-Cretaceous, predominantly andesitic mineralised belts in the region are now thought to be subduction-related magmatic arcs. The Inner Carpathian arc and the Eastern Bosnia or Drina-Rhodope arc host numerous vein and replacement deposits with epithermal features and Zn-Pb+/-Ag as the predominant economic minerals. In contrast, the south Apuseni Mountains have produced over 1 600 t Au from epithermal veins but very little Zn-Pb. Recent age determinations and geophysical data from the Baia Mare district of the Inner Carpathians suggest that mineralisation succeeded volcanism by 1-2 m.y. and accompanied crustal extension and the cooling of a large, mushroom-shaped pluton whose boundaries define the mineral district. In the south Apuseni district, mineralisation can be explained by mixing of meteoric with low-salinity metamorphic water expelled during intrusion of mafic rocks into the middle or lower crust. The more continental or cratonic crust in the Drina-Rhodope and Inner Carpathian arcs precluded the input of low-salinity, Au-bearing metamorphic water; the Zn-Pb deposits formed where convecting meteoric water mixed with saline water, possibly introduced through carbonate rocks in the basement

Aug 1, 1996