Search Documents

The following is a Maintainability Design Checklist for coal mining equipment. The purpose of the checklist is to provide a summary of design review points for the maintainability assessment of new or existing underground equipment. It specifically focuses on the identification of equipment design features, tasks, or procedures that impact equipment downtime, repair costs, labor hours and maintainer skill level requirements. Some checklist points are general in nature. The checklist was designed to be used across all categories of underground equipment. The intent is to draw attention to design features and maintenance procedures that will increase maintainability requirements. You are encouraged to adapt this checklist to site specific or machine specific requirements by: Inserting specific performance criteria for various categories of maintenance tasks. For example; all hydraulic lines on a shuttle car should be replaceable in 15 minutes or 25 minutes, etc. Adding or deleting checklist items for different categories of equipment. You would include environmental control equipment, for example, on face equipment and not on shuttle cars or man trips. Adding additional checklist items based on site or equipment specific maintenance histories or experience, company maintenance standards, or other factors.

Jan 1, 2000

By S. P. Vanka, B. G. Thomas, S. Sivaramakrishnan

"During the continuous casting of steel, transient 'flow events can be very important to the generation of quality problems, such as shear entrainment, surface level fluctuations and bubble entrainment. These phenomena can be better predicted using Large Eddy Simulation (LES) models than the K-E models, which have been extensively studied. In this work the turbulent transient flow in a water model of a continuous caster has been both simulated using LES models and measured using Particle Image Velocimetry (PIV). The results of PIV and LES have been compared to validate the LES model and also to enhance the understanding of the prominent transient features of the flow field. The flow near the top surface in PIV was found to contain periods of 5-1 Os when the velocities were three to four times their mean values, which is of importance to the shear entrainment of the liquid flux. In both simulation and PIV the upper roll structure is found to change chaotically from a single large recirculation structure to a set of distinct vortices. The inlet swirl in PIV is seen to persist more than halfway across the mold, causing a characteristic staircase velocity vector pattern when viewed in a plane parallel to the wide faces. The lower rolls in PIV are significantly asymmetric for very long periods of time (- I-hour) and go through a repeating sequence of features. One of these features involving a short circuit between the upward and downward flow in the lower roll is also seen in the simulation and is of significance to bubble entrapment.IntroductionThe turbulent flow through the nozzle and in the mold of the continuous caster has been studied extensively using computational Reynolds Averaged Navier Stokes (RANS) models of turbulent flow [1,2]. Defects, such as internal inclusion of liquid fl4x through surface shear, pencil pipe defects due to bubble entrapment, surface defects due to level fluctuations are caused by transient flow phenomena oc'curring in the mold. These phenomena can be better predicted using transient Large Eddy Simulation [3] or ""LES"" models."

Jan 1, 2000

By H. Dong, J. J. Valencia, L. Nastac

"A comprehensive computer model was developed to understand and optimize the centrifugal casting process for manufacturing TiC/Al-bronze friction drums. Performance of these components requires proper distribution of TiC particles, which is shown by dimensional analysis to be dominated by centrifugal buoyancy effects and solidification kinetics.The model addresses the following: (1) a rheology-viscosity model of the interference between moving particles, (2) engulfment (entrapment) or pushing of particles in the mushy region by the advancing solid/liquid interface, (3) nucleation and growth of equiaxed and eutectic phases, (4) effects of particle size, particle concentration, and cooling rate on the final grain size, and (5) the impingement effect of particles on the nucleation and growth kinetics of solidifying microstructure.Parametric studies were conducted using the computer model to investigate the effects of various process and material parameters on the distribution of TiC particles. The effects of the volume fraction, size, and morphology of the particles (including clusters and agglomerates) on the particle distribution were evaluated in detail. The complex interaction between the solidifying structure and insoluble ceramic particles in centrifugally-cast metal-matrix-composites was also investigated.The model predictions of particle distribution and microstructure were validated with experimental data for centrifugally-cast A356/SiC and TiC/Al-bronze alloys.This work was conducted by the National Center for Excellence in Metalworking Technology, operated by Concurrent Technologies Corporation under contract No. N00140-92- C-BC49 to the U.S. Navy as part of the U.S. Navy Manufacturing Technology Program."

Jan 1, 2000

By Kimio Itagaki, Makoto Ohtsuka, Kouki Chiba, Minoru Matsumoto

"The properties of Ni-Mn-Ga films such as chemical composition, crystal structure, microstructure and transformation temperature were investigated with respect to sputtering conditions in the present study. The Ni-Mn-Ga films were deposited on a polyvinyl alcohol substrate with a radio-frequency magnetron sputtering apparatus using the NisoMn2sGa2s and Nis2Mn:«1Ga24 targets. After separating from the substrates, the films were annealed at the temperature between 873 and 1273 K for 3.6 ks. The chemical composition of the films depended on the radiofrequency generating power, however, there was no dependence on the heat treatment temperature. Each deposited film had a columnar grain structure. After heat treatment, the width of columnar grains widened and then became indistinct with increasing heat treatment temperature. The Heusler type cubic crystal structure of the fi4n with heat treatment at 1073 K changed to the tetragonal one through the martensitic structural transformation during cooling. The martensitic structural transformation temperature increased with increasing nickel content of films, while the Curie temperature decreased. The film obtained at 200 W using the Nis2Mn24Ga24 target after heat treatment at 1073 K showed one-way shape memory effect through the reverse martensitic structural transformation during heating.IntroductionThe ternary intermetallic compound NiiMnGa has a Heusler-type crystal structure and is an intelligent material, which has a shape memory effect and a ferromagnetic property. The martensitic structural transformation occurs within the ferromagnetic temperature region. The cubic crystal structure of L21 at high temperature changes to a tetragonal one through the martehsitic structural transformation during cooling. The films of this compound can be applied for an actuator of micro-machines."

Jan 1, 2000

By Jun Lu

Compared with land mineral resources investigation, as well known, it is more important for marine geologists to get image data (e.g. photographs, video tapes and various charts) because they are often hard to reach deep seabed directly. In the past years a plenty of image data which are in various forms have been accumulated. In contrast with both digital and character data managing the image data by using database is just unfolding and it will be a trend for marine mineral resources investigation. GIS (Geography Information System) offers another useful means of processing image data, especially geological data. GIS is characterized by processing vector data (e.g. point, line and polygon), but newer versions of GIS software package are also able to process raster data (e.g. photographs etc.). The present author made a presentation on marine mineral image database during 25th UMI, but that system runs under DOS environment and dealt with only mineralogy. Recently a new system which integrates Oracle image database with GIS (ArcView version 3.1) has been developed. This system runs under Windows NT environment. In the network environment Server/Client mode is adopted, and over 200 basic subdatabases (tables)are located on Server; operating interfaces are located on several clients so that several persons can operate the system simultaneously. The whole system involves five types of marine mineral resources: manganese nodules, cobalt-rich crusts, polymetallic sulfides, phosphorites and gas hydrates. The data of every type of marine mineral resources described above are distributed among five units and several blocks. The units and blocks are described below:

Jan 1, 2000

By M. Board, R. Pakalnis, S. Seldon, R. Brummer

The Kidd operation mines roughly 10 000 tpd of copper and zinc ore from underground and employs about 700 personnel. In the late summer and fall of 1997, major movements in the proximity of the east wall of the Kidd open pit had been observed. The Kidd pit had been mined from 1965 to 1977 to depths of 260 m (850 ft), followed by subsequent mining by underground methods to current depths in excess of 1830 m (6800 ft). The No. 1 Mine (2600 Level to pit bottom) is approximately 90% extracted, with most of the remaining reserve between 2000 and 2500 levels. Although initial concerns centred on the stability of the pit walls, the potential ramifications of the movements to the underground were recognized and measures were implemented to ensure the safety of personnel as well as to minimize the potential damage to existing operations. In late October, damage to underground operations was observed as deep as the 2000 Level. In the final assessment, the global mobilized mass was a “wedge”-shaped hangingwall block extending from surface to about 610 m (2000 ft) below surface. The “wedge” boundaries are defined by a fault and shear zone which have continuous lengths in excess of 1070 m (3500 ft); its base by shearing through the host rock mass; and its eastern face by deep tension cracks (Fig. 1). Mined and filled excavations at the western face of the “wedge” allowed mobilization of a mass in excess of 30 M tonnes. Movements in excess of 75 cm (30 in.) per day were recorded on the surface stations that preceded the complete shutdown of operations on October 29, 1997. The evaluations in the days following the shut-down were centred on mitigation of immediate and future possible negative impacts on infrastructure and mining of the remaining No. 1 Mine reserves while ensuring the safety of the operators. This effort required the rapid assessment of the potential damage of the block movement on underground infrastructure, stope access, drainage and ventilation, as well as airblast potential due to the falling of a large block into the pit near the ventilation intake at the base of the pit. These assessments were presented in a previous paper (Seldon et al., 1999). In total, the lateral movement of the block on the ground surface was over 4.3 m (14 ft). This paper describes the detailed studies performed to understand the failure mechanism and to assess the impacts on future mining in No. 1 Mine.

Jan 1, 2000

By R. J. Kendall

As we enter the new millennium, the South African mining industry has to ensure that it becomes more competitive if it is to survive in the ever more demanding global environment. Traditionally, mechanization in narrow stopes has been limited to the use of scraper winches, and numerous mechanization attempts have been restricted to pilot projects operated on an extremely limited scale (with varying degrees of success). The benefits of hydropower are well documented, and Northam Platinum has shown these benefits to be achievable on a mine-wide basis. However, the equipment originally developed for hydropower systems has followed the traditional labour-intensive approach commonly used in deep level narrow stoping operations. The problems experienced with the hydropower system are discussed and the rationale for developing alternate technologies is explored. The hydropower system has shown to be a versatile powering medium which can be harnessed for a diversity of uses. It (hydropower) enables the mining engineer to change traditional paradigms and to design an entirely new approach for optimizing the mining operation based on explosive techniques. The system developed for Northam consists of the following: ?Purpose-built stope drill rig operated off the hydropower system with special features to ensure accurate drilling patterns throughout the length of the blast hole ?Purpose-built high rate cleaning system for rapid transfer of fractured ore to the stope orepass ?Redesigned stope layout to facilitate in-stope water control and to recover fines from the run-off water ?Purpose-built drill rig for rapid establishment of reef raises and advanced strike gullies ?Purpose-built drill rig for flat end development. On both types of development end rig, emphasis is placed on ensuring accurate drilling patterns throughout the length of the hole to maximize linear advance per blast. The paper discusses the implementation of the Northam system on a large scale as well as current initiatives to further improve on the efficiencies of mining operations. It concludes by emphasizing that mechanized hydropowered stope technologies are in their infancy and thus offer unlimited scope in progressing beyond today?s paradigms to present as yet unthought of solutions for optimizing deep level ore extraction.

Jan 1, 2000

By T. C. Goel, A. Venna, R. G. Mendiratta

"Processing of ferrites has gained tremendous importance in recent times to meet the high performance demands on ferrites in keeping with the fast emerging· technologies. The quality of ferrite powders has strong influence on ·the performance of final device. Fabrication· of high performing ferrite components requires starting ferrite powders of precise stoichiometry, purity and microstructure. It is difficult to obtain these attributes by the conventional ceramic method. The key to obtaining quality powders lies in the· solution techniques. With this in view soft ferrites have been prepared by a wet chemical process, known as the citrate precursor method, which involves the formation of citrate complexes of the constituent cations. The advantages of this process are the ease of preparation and close control of composition, homogeneity, purity and particle size. Electrical and magnetic measurements on lithium ferrites have shown resistivity higher by more than two orders of magnitude compared to that observed for samples prepared by the conventional ceramic method, and low magnetic losses, making the ferrites specially suitable for high frequency applications.IntroductionProperties of ferrites are known to be sensitive to .their processing technique. A small deviation in the compositional stoichiometry of the ferrite affects its properties greatly. Soft ferrites such as Ni-Zn, Mn-Zn and Mg-Mn. are well known ferrites covering wide-ranging applications [1,2]. Lithiiim ferrites have also assumed technological importance for microwave applications and are potential substitutes for the expensive garnets [3]. Lithium ferrites are often doped with zinc to tailor the saturation magnetization required at high frequencies. Lithium and lithium-zinc ferrites, however, present difficulty to processing due to the volatile nature of both the cation components, namely Li and Zn. These ions are volatile at temperatures > 1000°C which makes their processing difficult. One of the main considerations of high frequency performance of ferrites is the high eddy current losses which prevent the interaction of the magnetic field with the ferrite component and hence impair device performance. These losses can be reduced by having a material of high resistivity. Electrical conductivity in lithium ferrite has been attributed to electron hopping [4] between the two vaience states of iron, Fe2+ <=> Fe3+, on octahedral sites. Maintaining the + 3 valence state of otahedral- Fe ions is thus a prerequisite for achieving high resistivity. The resistivity of ferrites is normally found to be low when processed by the conventional solid-state or the ceramic method [5]. This is attributed to (a) extensive ball-milling employed in the method to mix the component oxides results in non-stoichiometric compositions due to introduction of additional Fe ions on abrasion of steel balls during milling, (b) high processing temperatures involved which result in significant volatilization of Li and Zn ions creating thereby oxygen non-stoichiometry which results in reduction of Fe3 + to Fe2 +, (c) large and non-uniform grain sizes. In the present work, preparation of Li and Li-Zn ferrites by a non-conventional method known as a citrate precursor method [6, 7] which requires lower processing temperatures and duration is reported. The method gives stoichiometric compositions on account of homogeneous atomic-scale mixing of the constituent cations via the formation of metal-citrate complexes mixed in solution state. The method is also capable of giving small grain size which aids the oxidation ofFe2+ ions."

Jan 1, 2000

By Dale Preece, Steven Sobolik, Richard Jensen

Recent events demonstrate that civil and government facilities and structures face an ever-increasing need to be designed for protection against malevolent explosions. Modification of existing public structures and especially design of new ones increasingly includes provisions for explosive protection. ISEE members endorse and promote responsible application of explosives to benefit mankind and deplore any other use. However, our knowledge of explosive behavior and our ability to predict the results of explosive events puts us in a unique position to give guidance to designers of civil and public structures. Recent advances in computational methods have resulted in new computer codes with ALE (arbitrary lagrangian eulerian) simulation capabilities. Historically, lagrangian computational methods have been used for modeling solids because the mesh or discretization moves with the material. Rock breakage resulting from explosively induced shock-waves has been successfully modeled with lagrangian codes. Explosive detonation has traditionally been modeled with eulerian techniques. Eulerian methods have been used to model gases and fluids, tracking the material as it moves through the computational grid. ALE computational technology couples the two methods together in a manner never before possible. An ALE simulation can accurately treat the explosive detonation, interaction of explosive gases with air, and the impact of explosive event on nearby solid structures. ALEGRA (Budge et al. 1997 a & b) is an ALE code developed at Sandia National Laboratories. ALEGRA simulations accurately predict the explosively induced impulse on the structure to be protected. It has been applied to the analysis and design of blastwalls to protect structures and people from explosive events. The impulse calculated can be used by structural engineers to design a blastwall. ALEGRA has also been applied to predict the effect of a blastwall on explosion overpressure some distance behind the blastwall to assess the effect on people present during the event.

Jan 1, 2000

By D Guibal, J Vann, M Harley

Many sample value distributions are highly skewed and present variograms with high relative nugget effects and/or short-range structures. In consequence, significant deskewing of the histogram and variance reduction occurs when transforming between sample and block support, where blocks are of significantly larger volume than samples. When making estimates in the mining industry we usually wish to estimate on the basis of block support rather than sample support. The selective mining unit (SMU) refers to the minimum support upon which ore/waste allocation decisions can realistically and practically be made. The SMU is usually significantly smaller than the sampling grid dimensions, in particular at exploration/feasibility stages. In a non-linear estimate, for each large block (by convention called a æpanelÆ) we estimate the proportion of SMU-sized parcels above a cut-off grade threshold. A series of proportions above cut-off defines the SMU distribution. Use of such non-linear estimates reduces distortion of grade-tonnage curves and provides a better basis for mine planning and economic decision-making. At present, Multiple Indicator Kriging (MIK) is the most widely used technique for performing estimation of recoverable resources. MIK is not the only approach available and it has some potentially serious limitations. The MIK technique is described and a number of theoretical and practical implementation issues are examined. In particular: MIKÆs assumptions about spatial distribution of grade; the behaviour of indicator variograms; application of change of support models; order relationship problems; and modelling the tail of the distribution. Some simple tests are described which allow us to determine the suitability of different estimators for a given deposit and criteria to identify a preferred estimator are also examined. Uniform Conditioning (UC), an alternative estimator which may be used instead of MIK, is described.

Jan 1, 2000

By Cleusa Cristina Bueno Martha de Souza

Nowadays in Brazil the final disposal for spent batteries include sanitary and industrial landfill for hazardous waste from domestic waste and industrial waste respectively. The problems of environmental impact caused by spent batteries had been discussed of several years, considering the fact of metals contents, like Cd, Hg, Pb and Zn. Some techniques are been proposed for recycling this type of waste in order to protect the environment while bringing also economic advantages of recovering metals. The reclamation of metals from secondary raw materials had been employed and further applications of this flexible technology are planned to the future. The processing of metals solutions involving hydrometallurgical techniques is an efficient method for recovering metals, since it provides completely recovery of metals with low energy requirements. This paper discusses the spent alkalline batteries characterization and leaching stage experiments results with sulphuric acid as leachant. After batteries dismantling by mineral processing techniques, the black powder sample produced was submitted to diffraction X-ray characterization and atomic absorption spectrophotometry in order to verify all the substances presented. Some experiments were carried on to develop a hydrometallurgical process for initial metal recovery aiming to get Zn into a soluble form on aqueous solution in order to propose the next stages of purification and recovering Zn, as electroplated deposition. The sulphuric acid was chosen not only for being cheaper than other leachants but also for improving the extraction of soluble Zn as ZnS04 form at diluted acid concentration. Batch laboratory experiments leaching procedure were conducted to determine appropriate leaching conditions from the viewpoint of maximize zinc extraction. In these tests an amount of dry powder batteries was added to different acid concentrations and solid/liquid ratio and after leaching and filtration the aqueous solutions were submitted to atomic absorption spectrophotometry analysis to verify the Zn content.

Jan 1, 2000

By D. R. Parker

"This paper canvasses emerging trends in public policy and law, which may influence the zinc industry's interest in recycling. There are forces at work beyond direct economic benefits that will drive recycling of zinc, including:• corporate determination to pursue sustainable practices and product stewardship.• public perceptions and pressure,• customer and investor demand,• workforce recruitment, and• protection and expansion of marketsIn this paper, these ""indirect"" forces are examined with particular focus on the zinc industry: It is concluded that, in today's world with an emerging precautionary approach to policy and law making, public perception concerning the environmental implications of metal products, and the need to conserve resources for future generation, a strong industry response is required."

Jan 1, 2000

By D. W. Dew

Billiton Process Research has carried out extensive research over the past four years to develop new process technology using bioleaching for extraction of copper and nickel from their sulphide concentrates. Continuous pilot scale and laboratory batch testwork has been carried out with adapted mesophile bacterial cultures at40°C?45°C, moderate thermophile cultures at 50°C?55°C and thermophile cultures at 65°C?85°C. Pilot scale work has demonstrated the commercial viability of mesophile cultures for bioleaching of secondary copper sulphide and nickel sulphide concentrates. Moderate thermophiles offer benefits in terms of reduced cooling requirements for commercial reactors and, in the case of bioleaching of nickel concentrates, some selectivity over bioleaching of pyrite. Continuous pilot scale testwork has shown that thermophiles achieve efficient bioleaching of primary copper sulphide and nickel sulphide concentrates, giving much higher recoveries than achieved by bioleaching with a mesophile or moderate thermophile culture.

Jan 1, 2000

Block caving is the lowest cost underground mining method but it has relatively high risks and a high up-front capital and development cost. It has application to large, often lower-grade orebodies where high production rates can provide good returns on the investment. However, it has a range of technical risks that are peculiar to block caving and the usual financial, political and environmental risks that may be exacerbated by the long lead-in times associated with the development of a block cave operation. With initial development costs that may be $100 M to $1000 M when the building of a treatment plant is also required, it is obviously important to minimise and manage the risks. In a greenfield project, commitment to a substantial proportion of the capital expenditure may be required to gain access to the deposit, and the decision to proceed at this stage would be based very largely on interpretations of drill hole data. In established mines the data may be supplemented by geological mapping and past experience, etc. The quality of this data is critical and yet it is frequently degraded through poor techniques and avoidable omissions. The final decision to proceed would be assessed on projected commodity prices, mining capital and operating costs, dilution and run of mine ore grades. The latter will vary over the life of the project and these can be estimated with drawdown or draw control modelling techniques. In this modelling, there are further risks in the assumed modelling parameters or that the modelling technique may not be applicable or appropriate. The paper addresses the most critical technical and operational risk areas and provides some practical precautions that can be taken to reduce these and improve the reliability of the geological and geotechnical models.

Jan 1, 2000

The ninth annual Mine Rescue Evaluation was held in conjunction with the RMCMI 2000 convention at the Sheraton Tamarron Resort, Durango, Colorado June 25 thru 27. The purpose of the mine rescue evaluation program is to provide an opportunity for mine rescue teams to learn new skills and improve their existing ones in a non-competitive environment. Several staged "disaster" scenarios were [ ] held where the teams are called upon to exhibit their life saving abilities. The evaluators meanwhile are offering suggestions, both verbal and written, to help the teams better understand the situations presented them. This non-competitive environment allows the teams to work together and share their knowledge with fellow mine rescue teams providing everyone with a positive learning experience. Mine Rescue Chairman Bill Balaz was in charge of coordinating the events. Seven teams consisting of seven to ten members each (totaling 63 members) participated in the two-day event. Each team was required to respond to three different real-life scenarios plus a written general knowledge test daily. This year&apos;s four professional evaluators included Art Saenz (Hazardous Materials) of Western Envi¬ronmental Associates; Guy Horton (Ropes), Guy Horton Rope Rescue; Mary Bailey (Medical), MBA Training and Ron Lauer (Confined Space) also lassos Western Environmental Associates. They cash prov- [ ] ided three different challenging mock situations per day per team. The teams had no prior knowledge of what the scenarios would be as details were provided only as they arrived. Ten volunteer victims added much drama and excitement to the event. Their realistic enactments, complete with false blood makeup and severed limbs, made for some very tense scenarios. The Mine Rescue Teams participating this year were BHP LaPlata, BHP Navajo, BHP San Juan, all from Farmington, New Mexico; Bridger Coal Co., Rock Springs, Wyoming; Sabine Mining, Longview, Texas; Solvay Minerals, Green River, Wyoming and Western Energy Co., Colstrip, Montana. Many new [ ] friendships were made and much knowledge shared. A swap meet was held Saturday afternoon for the teams to exchange miscellaneous equipment, hats, shirts, etc. The teams were asked to evaluate the program and the evaluators. Then responded with many positive suggestions that will help improve the upcoming events in the years to come. Culmination of the Mine Rescue program was a Tuesday morning awards breakfast where the teams were presented with plaques. The participating victims and evaluators were also commended for their outstanding efforts. Sponsors for the Mine Rescue program were Big Sky Coal Company, CMC Rescue, Magnum Metals, Inc., and Rocky Mountain Electric. Many hours of volunteer time and effort from various family members of participants helped make the 2000 event a huge success.

Jan 1, 2000

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30&apos;s of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity.

Jan 1, 2000

By P. J. Bartlett

Premier Diamond Mine exploits a kimberlite orebody using cave mining methods. A drilling level is established at the base of a block of ore to effect undercutting that leads to caving of the overlying ore. A second level is developed some 15 metres below the undercutting level to allow extraction of the ore once it has caved. As much as 45 per cent of the rock is removed on the extraction level creating a series of pillars. Undercutting creates abutment stresses, as high as 3 times the virgin stress, which affect the rock mass to a distance of 20 metres from the undercut face on the undercut level and on the extraction level 15 metres below. If the extraction level is completely developed prior to undercutting, where stress levels exceed 20 percent of the rock mass strength, extensive rock mass and support damage occurs as the undercut passes overhead. Rock mass damage takes the form of movement along existing joints and minor shear failure through intact rock. Support damage takes the form of cracking in rigid concrete linings. Where induced stresses exceed 50 per cent of the rock mass strength it is often impractical to keep excavations on the extraction level open. Rock mass damage takes the form of extensive failure of the rock in shear which evidences itself as propagation of the fracture zone around tunnels and footwall heave. Support damage results in destruction of shotcrete linings and concrete footwalls. As the interbolt support fails, badly fractured rock ravels around the steel tendons. Observation and monitoring at Premier Mine and on other cave mines has shown that induced stress levels and consequent damage are a function of :?the extraction ratio on the undercut and extraction level prior to undercutting ?the shape of the undercut face ?the rate of undercut advance ?the distance of leads and lags between adjacent tunnels on the undercut level. To ensure the stability of excavations, all of the above parameters must be carefully planned and the planned mining sequence rigidly enforced. The minimum of development is completed on the extraction level prior to the undercut passing overhead. Required development is then rapidly completed once the area has been de-stressed. Support is installed in three phases: ?Rockbolts are installed as soon as excavations are developed ?Wire mesh, steel tendon straps and a layer of shotcrete sufficient to protect the mesh and straps from damage by blasting and LHD loading is installed as soon as practical thereafter. Inevitably the shotcrete lining has to be replaced once the undercut has passed overhead.. ?Rigid shotcrete linings and concreted footwalls are completed only after the undercut has passed overhead and the area has been de-stressed.

Jan 1, 2000

By M K. Singh

Mining is nothing but an art - besides being a science - of extracting valuable minerals from the womb of the mother earth. In this gigantic task, a large number of machinery and equipment are employed judiciously. Wire ropes play a vital role in lifting or hoisting men and materials under hostile/adverse working conditions and constitute a major item of investment on machinery/equipment. The economy of using a wire rope is a concern for engineers, users and the planners. The economic use of wire ropes for mining purposes largely depends on the following factors;Mechanical design considerations - which include tensile strength of wires, elasticity, resistance to abrasion and crushing, fatigue values, static and dynamic loads on wire ropes, factor of safety, fleet angle, etc. Metallurgical consideration - Composition and heat treatment of wire materials, defects like inclusions and voids, surface quality factor, lubrications, micro structural parameters. Operational consideration - Seizing and cutting of rope, storage, care and maintenance, cutting back, etc. Environmental consideration - Temperature and humidity, pit condition, dust, corrosive atmosphere, etc. In the present paper, an attempt will be made to suggest steps for achieving optimum economy while using the wire ropes for extraction of precious minerals and coal keeping in view the points noted earlier. Once technical viability is established, economy is the ultimate consideration for an industry for safe hoisting of men and material.

Jan 1, 2000

By Dave Price

"Canada is scheduled to become the 4th highest diamond revenue producing country in the world by year 2004 with the already operating Ekati Mine and the anticipated operation of the Jericho Mine in 2002 and the Diavik Mine in 2003.This paper provides an overview of worldwide diamond production statistics and a brief introduction to a diamond processing plant. The dense medium separation (DMS) extraction process is presented and this process is discussed in more detail with respect to the extraction of diamonds in terms of feed preparation, dense medium, dense medium cyclones, ferrosilicon recovery and dense medium cyclone operating efficiencies.INTRODUCTIONThe Ekati Diamond Mine in the Northwest Territories started commercial production of diamonds in the 4* quarter of 1998. At full production, the mine is anticipated to produce annually some 3 million carats of diamonds. The Jericho Mine in Nunavut Territory and the Diavik Mine in the Northwest Territories are anticipated to come into production in the 1'' quarter of 2002 and 1st half of 2003 respectively. The combined annual diamond production of these three mines will total approximately 10.34 million carats by 2004, making Canada the 4~ highest diamond revenue producing country in the world.A diamond processing plant initially utilizes crushing, scrubbing and screening in the beneficiation process to liberate diamonds from kimberlite ore and size the product for further treatment through DMS. Alluvial diamond operations do not require initial crushing and scrubbing but incorporate a feed preparation and sometimes a recrush facility with the DMS plant. The heavy sink product from the DMS, which contains diamonds, is further upgraded through x-ray separation and high intensity magnetic separation prior to producing the final diamond product.DMS is a relatively simple separating principle. A mixture of particles of different density is immersed in a dense fluid, so that particles having a density lower than that of the fluid will float while those of heavier density will sink. The translation of the float-sink principle from a laboratory method to continuous industrial practice offers the prospect of very precise mineral separations based on density differences alone."

Jan 1, 2000

By David M. Spatz

The way people interact, collaborate, learn and improve can have a profound impact on a company’s efficiency, performance, productivity and return on investment. This is the motive behind corporate efforts today to replace the traditional hierarchical structure with team-oriented organization. The increased importance of communication and collaboration during the past 20 years has been propelled by rapid advances in technology and increased availability of information. Companies must take advantage of the information that is required for competitive performance and for the continued production of quality products. So it is essential that outstanding communication, cooperation and collaboration take place among multidisciplinary specialists assigned to work together to solve common problems and achieve common goals. Companies are searching for ways to increase knowledge transfer and learning, particularly among people who work on related topics. This will improve efficiency and quality and reduce redundancy and costs.

Jan 1, 2000