Search Documents

By Ivan Jackson Madura

The new Paradisus Coco Beach Resort in Rio Grande (PR) is located on an old swamp area, which has been filled with relatively clean to silty sands. The swampy deposits consists of organic silts, peat and loose fine to medium sand and silty sand. The project requires the placement of 1.0 to 1.5 meters of additional fill together with the construction of light structures. The need for the fill will trigger the development of settlements in the underlaying weak and compressible stratum. Furthermore, the susceptibility of the loose sand to liquefaction during an earthquake was considered. This paper describes the soil improvement by means of vibro-replacement, the purpose of which was threefold: reduction in total and differential settlement, acceleration of settlements during the surcharge period and densification of the loose sand to reduce its liquefaction potential. The predesign is presented together with relevant construction details of the preliminary trial areas from which the final column diameter and grid spacing were derived. Instrumentation together with settlement observations during the surcharge period are presented as well and compared with the initial predictions.

Jan 1, 2002

By T. Tamagawa, I. Iwasaki, N. X. Fu, M. Kobayashi

A three-stage fluidizing-bed process consisting of chlorination, selective oxidation and sulfur chloride conversion was tested for processing chalcopyrite concentrate. It was found that the use of excess oxygen was essential for the stable operation of the oxidation reactor. The excess-oxygen gas inevitably causes the oxidation of the sulfide concentrate in the chlorination and sulfur chloride conversion reactors. A new flowsheet is proposed to separate the chlorination and selective oxidation steps with separate flow paths of the fluidizing gases, thereby, preventing the passage of excess-oxygen gas in the chlorination and sulfur chloride conversion reactors. The feasibility of the proposed flowsheet was demonstrated in a laboratoryscale fiuidizing bed setup.

Jan 1, 2002

By Alicia E. Ares

316 L Stainless Steel samples were solidified directionally under conditions which produced the columnar to equiaxed transition. The position of the transition was located in each sample and the distance from the bottom of the ingot was measured. During solidification the distribution of temperatures were measured by means of thermocouples located strategically. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solidus fronts. Comparing the location of the transition and the values of these parameters it was found that the temperature gradient reaches negative values of as low as -13.44 "C/cm, and velocities of the fronts of around 0.1 cm/s. Also, a supercooling of 5.81°C were measured which was associated with the supercooling for the nucleation and growth of the equiaxed grains ahead of the columnar front. In addition the primary and secondary dendritic spacing was measured in both regions. The spacing was compared with the predictions from available models. The results are presented and discussed in the frame of the results obtained for other alloys

Jan 1, 2002

By George Hope, Brigitte Lacouture

"The Red Dog Mine has increased mill throughput for most years since startup. Although flotation equipment has been added over the last 10 years, the Red Dog metallurgical performance has been restricted by a lack of adequate flotation capacity. Two reduced tonnage trials conducted in 1997 as well as numerous SAG relines have consistently indicated the potential to significantly increase both zinc concentrate recovery and grade with additional flotation capacity. Late in 1999, a new circuit was designed with increased flotation capacity while simplifylng the current circuit, providing for three stages of dilution cleaning, and creating a retreat section. The purpose of the retreat section is to target the more complex particles and allow the chemical environment to be fine tuned for improved iron depression. In total, twentyone (21) Outokumpu OK50 mechanical flotation cells and four (4) 3.66m dia. column cells will be added to the current flotation circuit. The VIP (Value Improvement Program) Mill Optimization project is also addressing thickening, water treatment and power issues and has a total budget of $US105 M. Startup of equipment will be phased in to minimize the impact on current operations and is expected to be complete by the end of Q3-2001.INTRODUCTIONRed Dog Operations started production in November 1989. The mine is located above the arctic circle in northwest Alaska. It is linked by an 80 km road to a port-site facility where the concentrate is stored. Concentrate is shipped to markets throughout the world during the one hundred (100) days of open seas. Typical of sedimentary exhalative deposits, the metallurgy proved to be challenging and coupled with many mechanical shortcomings, the initial few years were very difficult. The start-up issues were slowly resolved and in 1998, a major grinding expansion, the PRI (Production Rate Increase) project, was completed. The project was designed to allow a 40% increase over the 1995 throughput. In 2000 mill throughput was 3,050,000 tonnes to produce a total of 960,000 and 140,000 dry tonnes of zinc and lead concentrates respectively, making Red Dog the largest zinc concentrate producer in the world. To address a shortage of flotation capacity remaining from the PRI grinding expansion, a project designated as the VIP (Value Improvement Program) Mill Optimization project was initiated. The mill optimization project is targeted to produce 1,100,000 tonnes of zinc concentrate at 56% zinc grade and 87% zinc recovery. The project will add twenty-one (21) Outokumpu OK50 (50m3) flotation cells, four (4) 3.66mO column cells and address water treatment, thickening and power generation capacities."

Jan 1, 2002

By T. R. Ellis

"The valuation of mineral properties in the U.S. is only partially regulated. The regulations which have jurisdiction or impact appear to have such mainly as a consequence of unintended fallout, since the regulations were designed for other purposes. Court case history can also be important. The combined results are a mixture of bad and good, with important lessons to be learned.Since 1981, the Securities and ExchangeCommission has prohibited U.S. listed companies from reporting quantitative estimates of mineralization and the value of mineralization, other than proven and probable reserves. This results in the minerals appraiser (valuator) working with a shortage of data in his everyday work, both on the subject property and in sales analysis.Between 1989 and 1995, all 50 states and essentially all federal agencies adopted the Uniform Standards of Professional Appraisal Practice (USPAP) for real property appraisals (valuations). The major national appraisal societies also require their members to abide by USPAP. A significant portion of minerals appraisals must now follow these standards. This paper will discuss the content of USPAP. It provides a very good framework for the valuation of a minerals property or a mine, both as real property and as a business. However, the credentialing standards for real property appraisers are now prohibitive for minerals appraisers."

Jan 1, 2002

By Aly M. Mohammad

The Delaware River Tramway will link civic and retail developments in Philadelphia, Pennsylvania and Camden, New Jersey. Twin 300-foot towers will anchor the cables at either side of the river. Four high capacity drilled shafts designed by the Geotechnical Department of DMJM+HARRIS support each of the towers. At the Philadelphia tower, each 6-foot diameter shaft extends 130 feet deep and terminates with a 30-foot rock socket. The shafts are situated within the footprint of an existing relieving platform, which complicates the typical construction sequence. Also, the subsurface conditions at the site provide a unique challenge in both the design and construction of the drilled shafts. During the construction of the four-drilled shafts for the Philadelphia tower, a 6000-ton Osterberg load test was performed on the first shaft to verify design assumption and confirm the shaft capacity. The results of the test were utilized to establish load transfer characteristics and develop foundation design parameters suitable for the site conditions. By doing so the Design Engineer was able to reduce the length of the rock sockets on the remaining production shafts by approximately 5 feet per shaft. As a result, the test provided a significant cost saving to the Owner by eliminating 15 feet of rock drilling from the construction costs. This paper presents a description of the unique design and construction methods adopted for the foundations, also on the Osterberg load test including equipment used, number and locations of strain gages, and interpretation of results. The results and findings presented in this paper could benefit both the design and construction industries because it provides a comparison between geotechnical design assumption and actual field measurements; which has always been a challenge particularly for rock formation.

Jan 1, 2002

By Inn-Joon Park

Major problems associated predicting soil-structure interaction behavior are based on the fact that soil is neither homogeneous nor elastic and soil properties are spatially variable. There also exist significant coupling problems between the behavior of the structure and geologic media. When designing foundation or other geotechnical structures, the load transfer between the soil and structure takes place at the contact surface. This surface is called the interface. The behaviors of interface play an important role in the load-deformation response of soil-structure interaction systems. The purpose of this study is to develop improved model for simulation of saturated sand-steel pile interface behavior based on a general concept, called the disturbed state concept (DSC), which can characterize the behavior of saturated soils under dynamic loads. In this study, the Disturbed State Concept (DSC) constitutive model is calibrated and modified for steel pile-saturated sand interface and interaction by using the continuous hardening model for relative intact (Rl) state and the critical state model for the fully adjusted (FA) part in the saturated sand material. The general formulation for implementation has been developed. Then, the DSC model with modification for interface and saturated sand is implemented in finite element program based on the generalized Biot's theory. The interface tests under one-way monotonic and two-way cyclic loading and cyclic triaxial tests are executed for defining the parameters for interface and surrounding soils. Based on these parameters, steel pile-saturated sand interface and interaction are numerically simulated using the finite element program modified in this study. The DSC predictions show improved agreement with the observed results from laboratory test.

Jan 1, 2002

By M. Mirnezami, D. Lascelles, J. A. Finch, E. El-Ammouri

"In a previous publication, the depressant action of Mg above pH 10 on Cu-activated sphalerite was described (Lascelles et al., 2001). In the present communication, a second role, aggregation is introduced.Aggregation (i.e., the tendency of particles to cluster) is measured using settling rate and turbidity converted to an aggregation index (AI) where 0 corresponds to dispersed and 1 to aggregated. Surveys of Cu and Zn flotation stages at four concentrators showed the A1 increased significantly above pH 9. The metal ions identified in the process waters, principally Ca and Mg, were tested to determine which might be responsible. The presence of Mg was found to be the most important, 50 ppm Mg having a greater impact than 500 ppm Ca fkom pH 9 to 1 1. In one plant, poor repeatability in A1 was suspected to be related to varying Mg levels; doping with Mg significantly increased AI.In both aggregation and depression, therefore, the common feature is the impact of Mg at pH > 9. Over this pH range Mg forms a range of hydroxy species, including Mg(OH)2 precipitates. Suggested aggregation and depression mechanisms associated with these precipitates are introduced. Possible problems and opportunities arising from the findings are discussed.INTRODUCTIONProcess waters in flotation circuits contain a variety of metal ions that may introduce unwanted activation or depression. Two common metal ions are calcium and magnesium. Typical concentrations are in the range 50 ppm Mg and 500 ppm Ca (Marticorena et al., 1994, Basilio et al., 1996, Negeri et al., 1997, Nesset et al., 1998)."

Jan 1, 2002

By Q. J. Browne, M. A. Miller

Silver Bell produces about 22,000T of fine copper annually from low-grade chalcocite and oxidized copper ore that is recovered by sulfuric acid leaching and SX-EW processing. The current mineable reserves are 146 million short tons averaging 0.39% Cu, at a 0.15% cutoff. Silver Bell utilizes two types of mining methods to develop the low-grade reserves: (1) a conventional blast, load and haul method for run-of-mine leach ore, and (2) rubblization of material on the margins of existing pits. Rubble leach ore is blasted, terraced with a bulldozer, and leached in place. Mining and/or rubble leaching is currently active in four separate pits. Laramide-age intrusive rocks host porphyry copper mineralization at Silver Bell. Quartz monzonite porphyry dikes and stocks, mafic-poor equigranular granite (alaskite), and sub-volcanic dacite porphyry are the predominant host rocks. Most of the ore currently mined comes from near-horizontal enrichment zones containing veinlets and disseminated grains of pyrite and chalcopyrite rimmed by chalcocite. Conversion from a milling operation to a leach only operation allowed for a much lower cutoff grade than was historically used at Silver Bell. Mine geologists were able to increase copper resources by drilling exploration targets that were previously interpreted to provide lower-grade mineralization below cutoff-grade for milling. Geologic parameters that effect the distribution of rubble and mineable leach ore include: ore grade and thickness, variable alteration styles in intrusive host rocks that affect fragmentation during blasting, acid consuming carbonate wallrocks (reactive skarn) which influence leach solution pH, solution flow paths and drainage, presence of leachable oxide mineralization in non-reactive skarn, and depth to hypogene mineralization which is currently uneconomic. Geologic parameters are used to predict rubble bench limits, vary blast hole spacing for consistent fragmentation, and correct errors in mineral zone classification based solely on blast hole assays. An expansion-drilling program has identified approximately 150 million tons of new leachable copper resources with an average grade of 0.35% Cu.

Jan 1, 2002

By Anthony D. Barley

Over 60,000 multiple anchors have been used internationally since their introduction in the early 1990s, including 1000 in the United States. The multiple anchor system comprises a "multiple" of "unit" anchors installed within a single borehole - each unit anchor being staggered within the borehole length to mobilize its own capacity independently of the other unit anchors. These systems offer higher capacity than conventional anchors with identical bond lengths due to superior load transfer efficiency. The use of higher capacity anchors may allow reduction in the number of anchors required on a project, which results in time and cost benefits to the anchor installer, contractor, and the owner. Fully removable temporary multiple anchors are available, and have been used with consistent success. Three case histories are discussed highlighting the use of these systems

Jan 1, 2002

By F. S. Kendorski

Several startup or longtime underground stone mines have experienced unanticipated roof control difficulties due to the variable geologic character of the roof strata. Careful mapping of roof conditions, and identification of controlling geologic and mine geometric factors, lead to an understanding of the mechanisms causing roof problems. Factors such as unexpected rolls of the roof strata resulting in a gradual change from strong to weak roof; encountering open water-filled master joints; roof strata delamination due to internal water pressures; local karst features with mud, sand, and water hazards; and sudden loss of limestone roof due to paleo-channel erosion are some recent problems described. Strategies for overcoming these problems are discussed and detailed.

Jan 1, 2002

By G. Shore

"The development of a DC resistivity instrumentation system for data acquisition in extreme topography yielded an unexpected bonus in the quality and information content of the type of raw data gathered. Not only were traditionally too-rough areas being investigated systematically for the first time, the unique high-density, multi-directional raw data were providing the opportunity to greatly expand the range of conductive and resistive signatures that could be accurately recognized. Using a true 3-D inversion algorithm, 3-D earth resistivity imagery began to show distinctive anomaly patterns for hydrothermal mineralization at the seldom-visited resistive end of the spectrum, successfully imaging epithermal gold systems in conditions that had defied conventional ground and airborne geophysics for years.The traditional mode of designing a resistivity survey to test a specific target concept was shown to be an unnecessary limitation on exploration thinking when a single sweep acquisition of dense, multi-directional 3-D raw data could effectively provide the all-targets “shotgun” coverage that would take 10 or 12 conventional surveys to duplicate. Exploration planning has the opportunity to move from single steps of trial and error geophysical testing to a mode of mapping everything at the outset, and then sorting out what might be of exploration interest in the results. Survey parameterization becomes the non-technical process of marking an outline on a map and declaring “survey here.” Operational and interpretational reasons for not testing where the exploration interest lies have all but disappeared. With any-terrain capabilities and unprecedented raw data density and overlap to support interpretation of complex conditions, that outline can be drawn through extreme rough terrain, including lakes, cliffs, industrial facilities, and grounded installations to test for generally unknown sub-surface features of potential interest.As more is learned about the larger-scale signatures of ore settings and the district-scale geo-electric imprint of hydrothermal processes on lithology, it appears that the only thing certain about ore signatures is their uncertainty. This is not bad news. New opportunities abound as the advanced 3-D technology allows a first effective look at the previously unexplorable rough terrain or complicated settings, and a second look at areas where older results may now be known to be non-definitive."

Jan 1, 2002

By D Craw

Middle and Late Cenozoic fluvial conglomerates and gravel in northeastern Southland record the transport of alluvial gold from Central Otago into Southland, and subsequent reworking and concentration of this gold into economic placer deposits. A corridor of geochemically distinctive, Hg-free gold derived ultimately from veins in Torlesse Terrane schist in Otago extends through the Caples Terrane and into Southland. The initial repository in Southland was fluvial sediment of the East Southland Group, specifically weakly auriferous, quartzose delta plain strata of the Gore Lignite Measures (GLM), a downstream equivalent of Dunstan Formation in Central Otago. Miocene uplift along the northwest trending Old Man Range beheaded the parent river system, isolating GLM from its Central Otago source area and establishing the proto-Waikaia River system. Rising topography between Otago and Southland increased fluvial gradients, and initiated erosion of cover strata and a sequence of tectonically induced gold recycling events. Auriferous GLM were recycled from the hinterland into broad braided fluvial channel and floodplain deposits of the Waikaia Group (new), specifically the highly auriferous Waikaka Quartz Gravels and equivalent Waimumu Quartz Gravels downstream (WQG), superimposing more proximal depositional environments over parts of the former GLM delta plain. WQG were deformed, and locally cannibalised during the later stages of their deposition by reverse movement on north-northeast trending faults of the Dunsdale System (NW side up). Increased tempo of uplift in the hinterland (Old Man, Garvie, Umbrella, and Blue Mountain Ranges) in the Pliocene and early Quaternary resulted in further reworking of GLM and WkQG from the hinterland as well as basement erosion. Progressively more basement-rich detritus was deposited as a locally auriferous piedmont (Gore Piedmont Gravels - GPG) over earlier channel and delta plain (GLM, WQG) strata, extending from the Blue Mountains to Waikaia, and southward through the Gore Gap to beyond Mataura. Southward propagation of the north-northeast trending ranges, local warping, and uplift of the Murihiku Terrane in Pliocene and Quaternary progressively deflected GPG fluvial systems and ultimately constrained them to the present valleys. Pre-existing auriferous strata (GLM, WQG, GPG) were reworked and deposited with or without basement detritus as these fluvial systems migrated toward their present positions. Auriferous remnants of these transitional deposits are preserved in local structural depressions on the uplifted blocks that deflected the systems (eg King Solomon Mine), and on locally abandoned floodplain segments on the lowlands (Pebbly Hills-Gore Gap). The present drainage has continued to incise and cannibalise its own and earlier deposits during late Pleistocene-Recent uplift to form confined channel placers within the present valleys.

Jan 1, 2002

Threshold blasting involves the use of small amounts of high explosive to break and fragment hard rock without having to evacuate mining personnel. The method is easily assimilated and effective in rockbreaking, but requires rigid control on drilling, charging and timing. Current underground trials are aimed at fine-tuning the amount of explosive energy and blast hole geometry to allow the firing of multiple sets of shot holes in a continuous manner. Through correct procedures, the after-blast fumes, dust and fly rock can be contained so as to provide a safe working environment. Threshold blasting hugely reduces the volumes of explosives used in mining and brings to maturity the potential of the process begun by Alfred Nobel when he introduced nitroglycerine, and later dynamite, to mining. Its key contribution is its enabling of continuous mining operations with well understood and relatively low cost technologies. The use of batch blasting, employing large burdens holds the greatest potential for delivering high flow rates of ore at minimal cost. There is good potential for rapid evolution of the concept.

Jan 1, 2002

Gold mineralisation at the Macraes Gold Project is hosted in the Hyde-Macraes shear zone and can be traced for ~30km along strike, although economic resources are confined to a 7 km section in the vicinity of the Macraes township. The shear zone, which typically dips at a low angle (~20 o ) to the NE, is bounded by an upper hanging wall shear and a lower footwall fault. Mineralisation occurs along the hangingwall of the shear zone as well as in low angle concordant shears and stockworks. Ore types include graphitic cataclasites with variable amounts of quartz veining, ælode schistsÆ and quartz-vein stockworks. Rehabilitation at the mine has focused on creating an environmentally benign site dominated by pasture to allow continuation of the traditional pre-mine farming economy. Changing regional economics, continued urbanisation and a reduction in traditional employment opportunities has seen a rethink in the long-term rehabilitation outcomes. The community has recognised that the rehabilitated site will provide the basis of a viable tourism venture and the creation of a Heritage and Art Park (working title æGolden Point ParkÆ) is the culmination of that process.

Jan 1, 2002

By R. Heersink, C. H. Wells

Innovations in communications and real-time information systems are providing industry opportunities to improve profitability. Real-time operating data is collected from equipment across a site or even several sites into a central server for secure PC and PDA-based Internet access. This paper includes discussion of how operating staff can use wireless devices to see equipment and processing data from anywhere throughout the mines and concentrators, and how management can view results from multiple mines, all in real time. Additional opportunities enabled through the remote access by equipment vendors or mining consultants is also presented, as well as an overview of typical benefits and current installations.

Jan 1, 2002

By Douglas Rudenko

Have you ever had a neighbor complain about a blast one day, but says the next day’s blast was better, even though the Peak Particle Velocity (PPV) increased? How about neighbors that complain about a small trimming shot, but don’t complain about a big production shot? Have you ever reduced the pounds/delay and gotten more complaints? Mine operators are often bewildered when trying to correlate blast design parameters to homeowner complaints.

Jan 1, 2002

By Jinsheng Chen

Longwall mining-induced abutment loads on the surrounding coal pillars can be grouped into two categories in terms of the relative position of the coal pillars and the longwall face. They are the front and side abutment loads. Even though a lot of research and efforts have been made to study the nature and behavior of these longwall mining-induced abutment loads, their influence zones and magnitude are still not well defined and fully understood due to the complexity of geological conditions and the longwall muting-induced overburden strata movement. The uncertainty about the mining-induced abutment loads often forces consultants and mining engineers to employ a conservative approach in designing coal pillars and entry roof control plans. The problems with this approach are that: (a) it increases CM development¬longwall retreat footage ratio, (b) it decreases coal recovery, and (c) it increases !Ill' operating costs. However, a more liberal approach may create safety issues and result in loss of production. Therefore, the importance of accurately defining the influence zones and magnitude of the front and side abutment loads induced by longwall mining can never be over emphasized. The authors in this paper attempt to define the influence zones and discuss the magnitude of the longwall mining-induced abutment loads by analyzing the field data measured at RAG American Coal Company's longwall mines. In addition, the relationship between entry stability and the balance among roof/floor conditions, pillar design, and roof control plan is also briefly discussed.

Jan 1, 2002

By A. S. Macfarlane

The South African Institute of Mining and Metallurgy was approached by the Australian Institute of Mining and Metallurgy to present a paper on the current practice in terms of the valuation of mineral projects and properties, given the development of a Code for the Valuation of Mineral Properties, developed in Australia (the VALMIN Code), and a similar Code in Canada (the CIMVal Code).This paper is the result of research and investigation into the matter, in terms of the reporting of Mineral Resources and Reserves, financial reporting practice, the Listing Rules of the Johannesburg Securities Exchange, and various practices in valuation. The paper establishes that a strong linkage has already been established between the SAMREC Code for the reporting of Mineral Resources and Reserves and the Listing Rules, and that, for completeness, a Code for Valuation needs to be developed. This Code will be similar to its international counterparts, with the necessary inclusions which are relevant to South Africa, and will provide guidelines and definitions on matters such as transparency, materiality and competency in valuation. It proposes that a multi-stakeholder steering committee be established under the auspices of the SAIMM, to deliberate and design a process for establishing such a Code.

Jan 1, 2002

By R. P. H. Willis

For technology transfer to be successful a process, from research to full scale application, has to be followed. This paper describes such a process and how it is applied in practice. Some of the ?do?s? and ?don?ts? are highlighted. Recommendations are made on how to communicate existing knowledge and to ensure that a framework exists to effectively plan future projects with final technology transfer objectives firmly in place. The Impact Ripper System is used as a case study to illustrate lessons learned. Key words: Technology transfer, implementation

Jan 1, 2002