Search Documents

By A. Nkolele

Paper written on project work carried out in partial fulfilment of B. Tech (Metallurgical Engineering) degree Fine coal of the Goedehoop Colliery is dewatered by centrifuging before being sold. Full-scale plant tests were carried out to reduce residual cake moisture by the addition of surfactants. It is believed that by modifying the interface between the coal surface and the adherent surface water, as well as the water occluded in the cake voids, drainage is improved. Two anionic surfactants at concentrations up to 150 g/t were tested on coal of <0.5 mm size. The results demonstrate that quite high additions of surfactant (80 g/t)were needed to reduce moisture from 20 to about 17?18%. It was observed that when increasing surfactant additions at low levels, within a very narrow concentration range, the retained moisture first increased sharply only to decrease sharply immediately thereafter; this effect points to a critical surfactant concentration. Based on the obtained results, the use of surfactants cannot be recommended at this stage; further investigations under more controlled conditions are required.

Jan 1, 2004

By E. Chen, M. Barati, K. Coley

The reaction between carbon and slags is of significant importance in direct smelting of iron ores, EAF slag foaming and copper slag cleaning processes. This reaction is known to occur via gaseous intermediates and it is important to have fundamental data to understand the relative importance of each reaction step. In this study, the rate of CO2dissociation on different slag surfaces is measured using an isotope exchange technique. It was found that increasing iron oxide content up to 30 wt per cent does not have a significant effect on the rate constant while increasing from this limit, increases the rate constant dramatically. Activation energy of CO2dissociation on slags of unit basicity and different iron oxide contents is in the range of 180±40 kJ/mol. It is found that rate constant dependence on oxygen potential in the slag phase is increasing with iron oxide concentration. In the case of copper making slags, the influence of copper oxide is found to increase the magnitude of apparent rate constant, while decreasing the activation energy considerably. Key words: Gas-slag reaction, CO2dissociation, copper slag, kinetics, isotope exchange

Jan 1, 2004

By David Conover

Knowledge of the magnitude and direction of the horizontal secondary principal stresses is a critical factor in designing the layout and mining sequence of underground openings. Typically, horizontal stress measurement has been accomplished using overcoring or hydraulic fracturing. Hydraulic fracturing can be accomplished from surface boreholes prior to development, but the technique relies on numerous assumptions regarding the rock mass and the stress field, and interpretation of results is somewhat subjective. Traditional overcoring provides a more precise measurement, but requires underground access. To allow for precise measurement of the horizontal stress field from surface boreholes, the In-situ Stress Tool (1ST) was developed by SIGRA Pty of Brisbane, Australia. Used in conjunction with HQ wireline coring, the 1ST contains a battery-powered data logger that records tool orientation and monitors six diametral deformations as the tool is overcored. The IST has been used successfully for several years in Australia, but has only recently been introduced in the United States This paper discusses how the IST was used to measure the pre¬mining horizontal stresses at a western U.S. coal mine. Seven successful measurements were obtained in two holes at depths ranging from 250 to 800 ft. Results were consistent, showing moderately biaxial stresses greater than those expected from gravity loading, but relatively low compared to rock strength. In addition to describing the overcoring equipment and procedures, various problems encountered during testing and the accuracy of the results will be discussed.

Jan 1, 2004

By J, T C. McCuaig, J Hodgkison, T Fouet

Olympic Dam is the eighth largest Cu deposit and the largest U deposit in the world, with approximately 35 million tonnes of contained Cu and 1.2 million tonnes of U. The most recent resource estimate was for 2.95 billion tonnes of mineralised material with average grades of 1.2 per cent Cu, 0.4 kg/t U, 0.5 g/t Au, 2.6 g/t Ag as contained mineral resources. Olympic Dam is expected to produce >200 000 tonnes of Cu and 4200 tonnes of U3O8 from 9.8 million tonnes of ore in 2004, making it the 12th largest Cu producer in the world. One of the impediments to achieving targeted rates of production has been oversize material (>0.9 m) reporting to stope draw points. A major contributor to oversize material may be overbreak along pre-existing structural weaknesses from stope walls and backs during the production life of a stope. Underbreaking to structures can also have a detrimental effect on the performance of a stope. In an effort to understand the influence of structural geology on stope performance, WMC Resources and SRK Consulting partnered during 2003 to refine the current system of structural mapping, and to use historical data to produce a structural interpretation covering a large part of the mining area. The interpretation has been wireframed in DATAMINETM into a three-dimensional structural framework model. To date, there are more than 600 structures of >50 m strike length incorporated into the structural framework model, which covers a study area 1500 m + 600 m + 350 m. A back-analysis exercise to assess the influence of interpreted structures on overbreak and underbreak was completed for laser-surveyed stopes.

Jan 1, 2004

By A. K. Singh

Between the main fan and the coalface in a mine a lot of air is lost through leakage at stoppings, doors, air-crossing etc. so that a much larger quantity of air has to be circulated by the fan in order that the stipulated quantity of air reaches the face. Stoppings are of vital importance not only for effective ventilation of underground mines but also for isolation of areas affected by fire or susceptible to spontaneous heating. Generally, isolation stoppings are made of brick in cement mortar. If the area is far from the pit or unapproachable, it is very difficult and sometimes impossible to build these stoppings. To overcome these difficulties, particularly near fire affected zones, an alternate successful attempt was made in Indian mines to make a plug underground, from surface through borehole, using cement concrete. In this paper the salient features of the methodology adopted for construction of the plug and the experimental procedure for the measurement of air leakage by SF6 tracer gas is described. Measurements of air leakage through rows of ventilation stoppings in two mines viz. Moira (Jambad and Kajora seams) and Kuardi11/12 (Niga seam) collieries of Eastern Coalfields Ltd. (ECL) have been incorporated. Results of experiments conducted at the Central Mining Research Institute (C.M.R.I) to determine leakage through25 and 38 cm thick brick stoppings are also discussed. Results of all these studies are compared, which show that the efficacy and reliability of the remote filled cement concrete plug in respect of air permeability is satisfactory.

Jan 1, 2004

By A. Sandberg, M. Nzotta, Du Sichen, N. N. Tripathi, K. Beskow

The present study was carried out to investigate the impact of slag refractory lining reactions on the formation of inclusions during ladle treatment of steel. The experiments were conducted on an industrial scale in the ladle at Uddeholm Tooling AB in Hagfors, Sweden. The inclusion chemistry and population during ladle treatment were studied along with the composition of the ladle glaze, taken from the ladle lining. The inclusions in the steel were classified into four groups according to the Swedish standard SS 111116. SEM/EDS analyses were carried out to identify the phases present in both the inclusions and the ladle glaze. The number of inclusions in the steel before deoxidation was found to increase with the ladle age, i.e. the number of times the ladle had been in use. A similar increase was also found after vacuum degassing and before casting. A great portion of inclusions before casting was found to be supplied by ladle glaze. This observation was further confirmed and explained by thermodynamic analysis. The present results show that ladle glaze is a major source of inclusions in the ladle at Uddeholm Tooling. Keywords: Slag/ refractory/ lining?reactions, ladle glaze, inclusions, inclusion chemistry, ladle treatment

Jan 1, 2004

By F. Habashi

The pioneer work on pressure hydrometallurgy was conducted in Russia at the end of the nineteenth, and the beginning of the twentieth centuries, by Karl Josef Bayer (1847-1904) and Vladimir Nikolyevitch Ipatieff (1867-1952), both working independently in Saint Petersburg. Bayer was studying pressure leaching while Ipatieff was studying the precipitation of metals and their compounds by hydrogen under pressure. Gradually, industrial applications took place first in the aluminium and later in the nickel industry. Today, the technology is well established in a large number of industries, such as uranium, gold, zinc, titanium, tungsten, and more recently copper.

Jan 1, 2004

By J. L. Human, N. Fernandes

The rockfall hazard is the major contributing agency to fatal accidents in South African platinum mining operations. The majority of these accidents occur in close proximity to the working stope face. The collapse of fractured or blocky ground between individual temporary support units or the closest permanent support line to the stope face has not yet been adequately addressed. A large-scale stope support system testing facility funded by the Safety in Mines Research Advisory Committee (SIMRAC), has been designed and constructed to test support systems and stimulate innovative thinking by mining personnel, support manufacturers and suppliers by providing a facility where the interaction of stope support systems, a rigid stope face and a discontinuous hangingwall beam can be observed during quasi-static and dynamic conditions. Tests have been carried out on various types of stope support systems, focusing on the temporary support systems used in the immediate stope face area. The interlinking of the temporary support units with mesh or safety netting has been explored in the prevention of falls of ground between support units during gravity driven falls of ground. These tests illustrate the facility?s ability to be used to stimulate innovative thinking and provide a testing ground for the development of temporary support systems in order to reduce the risk off all of ground injury to mining personnel at the stope face.

Jan 1, 2004

By Fan Jiang, Haigang Wang, Shi Liu

"This paper describes several applications of Electrical Capacitance Tomography (ECT) in gassolid two phase flows. A new image reconstruction algorithm was evaluated by both simulation and experiments. It is then applied to the online measurement of solids distributions in square circulating fluidized beds (CFBs) and good results were obtained. From the measurement of solids distributions in the bottom zone of a CFB, a bubbly fluidization pattern is identified. A cross-correlation technique was combined with the solids concentration measurements to obtain the flow rate through the dip leg of the cyclone, i.e. the circulating rate of a test CFB. The same· technique was applied in a dense phase pneumatic transport pipe provides the solids concentration, and the flow rate of a wavy gas-solids flow.IntroductionElectrical capacitance tomography (ECT) has been developed for imaging multiphase distributions in the 90's of the ·last century. It is a non-intrusive method. The principle of ECT can be firefly described as follows:Firstly ECT uses a number of electrodes to surround the measuring zone, depicted by Fig. I. The capacitances between the electrodes are measured in turn and an array C is obtained that contains a total number of m independently measured capacitances. Meanwhile the measuring zone is virtually divided into a grid of n pixels, represented by an array G, named the image vector, the gray level of each pixel represents the local value of the concentration of the material. As the material distribution will be reflected by the capacitances between each pair of electrodes, such distributions can be reconstructed according to the measured capacitance, a process called image reconstruction. A common image reconstruction method is called linear-backprojection (LBP). It linearize the relationship between the dielectric distributions in the measuring zone and the capacitances between the electrodes as the following:"

Jan 1, 2004

By R. Boom, K. C. Mills, S. Riaz

This paper details the recent trends in slag-related research from 1999 to 2003. The trends in thefollowing are outlined: • Annual publication rate • Geographical origin of the work • Nature of the research (e.g. thermodynamics, kinetics) • Nature of the slag studied. This study has revealed that slag research in the USA and Europe has decreased to about a half over the last 20 years and that there has been a significant decrease in Japanese research in this area in recent years. However, these decreases have been offset by significant increases in Chinese and Korean research activity. There has been a significant increase in the amount of work carried out on the recycling and environmental aspects of slags in recent years.

Jan 1, 2004

By John Hutchings

Drilling and blasting is a clearly delineated work process, which has well defined inputs and outputs. Drilling and blasting is also a process with a number of steps each of which has measurable outcomes. Drilling and blasting is ideally suited to the application of Total Quality Management principles. Most drilling and blasting information is generally poorly managed with disjointed and unrelated Information Technology systems managing parts drilling and blasting data. Data is often moved from on system to another, sometimes manually. In the field, drilling and blasting is still very much a paper based system and which has not generally benefited from some of the recent hardware and software technology advancements now “on the shelf”. Data collected on paper rarely is transcribed back into an electronic system for further analysis. It is often difficult to collate or review historic drilling and blasting data. This paper will present a definition of Total Quality Management and demonstrate how it can be applied to the drilling and blasting work process. Total Quality Management defines the mechanisms for the application of continuous improvement to drilling and blasting. Continuous improvement will provide opportunities to modify drilling and blasting work process outcomes and generate real cost benefits within the overall mining process. A complete drilling and blasting management system frame work, called DBS, is presented in this paper. DBS provides all the components necessary to implement a full drilling and blasting Total Quality Management solution. Also highlighted will be appropriate “off the shelf” technology that can be applied to replace current paper based systems and provide the means to connect with other mine data systems. Various examples will be discussed which will demonstrate potential benefits of applying a structured Total Quality Management approach to a drilling and blasting work process.

Jan 1, 2004

By S. Cossio, J. L. Noyola, R. Espinosa

"Minera Penmont’s La Herradura is a joint venture between Industrias Peñoles, S.A. de C.V. and Newmont Mining Corporation. The mine is located in the northern Mexican state of Sonora. La Herradura consists of an open pit mine with a two-stage crushing plant and heap leaching facility. Gold is recovered from the pregnant solution using the Merrill-Crowe process; production began in July 1998. La Herradura produces about 130 000 oz gold per year and its treatment capacity is approximately 22 000 t/d. Ore mineralization occurs in a shear zone with quartz and native gold. Gold distribution is quite heterogeneous due to coarse visible gold, which in some cases ranges from 100 to 600 microns.Sampling and assaying protocols were established during exploration and prior to start-up of operations, based on nomographs developed from early heterogeneity tests. However, as the coarse gold problem became noticeable, it was necessary to develop new sampling protocols to have an acceptable relative standard deviation to control the fundamental error within ± 15%.An experimental program was developed and conducted on a selected ore block consisting of 195 blastholes; regular ore grade control procedures were applied to both sets of data to evaluate the difference in results between the protocol established prior to start-up of operations (existing) and the new protocol (leaching). In the existing protocol, sub-sampling is done through riffle splitters, and coning and quartering. Fire assaying was used to estimate the gold content on a 50 g sample. In the leaching protocol, a 12 000 g sample of bottle-rolled cyanide was leached, and the leach residue was assayed on a 50 g sample using fire assaying, and a weighted average total gold content was calculated. Currently, a new alternative method is being evaluated, where sub-sampling is done using rotary splitters, and fire assay on a 50 g sample; in this rotary sampling protocol and for comparison purposes, gold assays were also repeated using the leaching protocol.Test results were compared in three groups: < 0.3 g/t (below cut-off), 0.3 to 0.8 g/t, and >0.8 g/t. Overall, results show that the protocol established prior to start-up of operations underestimates the gold assays. Detailed technical results, alternative options, and their implications are discussed in the paper."

Jan 1, 2004

By R. Abel, T. Wildeman, N. Heflin

A study was conducted to assess environmental effects of waste rock piles on water in the Russell Gulch area. Each pile was rated on physical characteristics of proximity to an ephemeral gulch, extensiveness of erosion features, size, presence of vegetation, and presence of a kill zone. Chemical assessments focused on three leachate tests performed on waste rock samples. Ratings were based on pH, conductivity, acidity, and analysis for 31 metals using inductively coupled plasma emission spectroscopy. The chemical and physical assessment of each site is used to make a rating of each pile on its overall potential to deliver contaminants.

Jan 1, 2004

By Finlay Campbell

Nickel laterite pressure acid leach plants and reduction roast plants have had a checkered history in their engineering, construction, startup and operational reliability. Many potential projects have been the subject of detailed studies over the last thirty to forty years but relatively few have advanced to commercial production. Four reduction roast plants are currently operating, an additional one was partially constructed but never completed, and another was started up in 1974 and shut down after 12 years operation. Three acid leach plants have been built and commissioned in the last five years, trying to follow the example of the Moa Nickel plant in Cuba. An additional acid leach plant project is currently on hold, following limited construction work, its future subject to review by the owner because of potential cost over-runs. This paper attempts to discuss difficulties that may be encountered as a project is developed and will address factors which may affect production ramp-up schedule, long term production performance and overall production success. Comparisons are made with ramp-up performance at other large metallurgical plants that employ some comparable unit operations. Keywords: Caron, PAL, nickel laterite ore, ramp-up, reliability, process development, equipment design, step-out, commissioning, startup.

Jan 1, 2004

By R. Dippenaar

Traditionally, iron ore has been reduced with coke in a blast furnace and the hot-metal product of the blast furnace containing carbon, manganese, silicon, sulphur and phosphorous, was subsequently refined in a steelmaking furnace. During iron making as well as during steelmaking, significant amounts of slag are produced. Two decades ago, more than 13 m tonne of blast furnace slag and 4 m tonne of steelmaking slag per annum were produced in the USA alone. It is, therefore, not surprising that many attempts have been made to re-use iron and steelmaking slags. However, these slags are not merely metallurgical waste products but, on the contrary, their compositions and physical properties are judiciously designed to optimize the operations in the respective metallurgical reactors. The variation in composition and properties of blast furnaces lags are largely determined by the gangue in the ore and ash in the coke and much progress has been made in the re-use of such slag. With respect to steelmaking slag, emphasis has in recent years been placed on hot-metal treatment before refining and ladle treatment after decarburization. The bulk removal of silicon, phosphorous and sulphur from the hot-metal product of the blast furnace by specially designed slags prior to refining in a basic oxygen furnace, has reduced tap-to-tap time, lowered cost and produced steel of much higher quality. The use of synthetic slags in ladle refining techniques subsequent to decarburization in the basic oxygen furnace has resulted in reduced hydrogen and nitrogen contents and reduced solute impurities. Moreover, inclusion shape and composition control, again by the use of specially designed slags has led to the achievement of much improved mechanical properties of the steel. In these revised process routes, slag of different compositions are produced in the variety of unit processes and hence the re-use of steelmaking slags has become much more complex. Clearly, a thorough understanding of the design and use of these different slags is a pre-requisite to the development of re-use strategies. Japanese steelmakers have spearheaded attempts to reduce slag volumes in the individual unit processes and to strive towards ‘slagless steelmaking’ by recycling slags internally. Steelmaking slag volumes have been reduced on commercial scale from about 140 kg/tonne steel to 60kg/tonne steel. Moreover, model predictions have shown that, in principle, all slag can be recycled and the phosphorous extracted to produce fertilizer. This development is of particular significance since the supply of low-phosphorous iron ores is diminishing at an ever increasing rate. Keywords: slag, environment, iron, steel,

Jan 1, 2004

By I. Dymov, W. Phillips

A process has been evaluated, on a continuous pilot plant scale, to treat refractory gold arsenopyrite/pyrite concentrates. The process consisted of biological leaching to partially oxidise sulphides, followed by pressure leaching for complete sulphide oxidation and arsenic precipitation, followed by liquor neutralisation and cyanidation of the autoclave residue for gold recovery. This paper provides a brief description of the treatment flowsheet and discusses some of the main parameters and results of the process. During integrated pilot plant campaigns, it was confirmed that acceptable sulphide oxidation and gold extraction of 96-98% could be achieved by a two-stage oxidation with BIOX® (4 days total retention time) followed by PDX (40 minutes retention time at 220°C). Only partial arsenic precipitation was achieved in the autoclave, followed by complete precipitation by neutralization under atmospheric conditions. The overall process could be significantly simplified, and capital and operating costs reduced, with a flowsheet modification allowing all of the BIOX® liquor to bypass the autoclave directly to the neutralization circuit.

Jan 1, 2004

By M. T. Worley

Joint Development Associates International, Inc. (JDA) began humanitarian relief and community development in Central Asia in1992, following the collapse of the former Soviet Union. Appropriate technology has played an important role in their efforts to assist those segments of society that are most vulnerable to poverty and disease. Three case histories are described to illustrate the successful implementation of simple, but effective technology in community development.

Jan 1, 2004

By Julian Johnson

The effect of changing redox potential (Eh) on the high temperature sulfuric acid leaching of Western Australian dry-land nickel laterite ores has been investigated. In particular, the effect of added reductant (sulfur, sodium sulfite) or oxidant (potassium chromate) on Eh, leaching kinetics, metal extractions, acid utilisation and leach residues has been determined. Three separate ores - nonhonitic ores from Murrin Mumn and Bulong, and limonitic ore from Cawse - were used in the study. Sulfur addition varied from 0 to 7.8 kg/t ore. The total acid loading was kept constant at 430 kg/t (Murrin Murrin ore) and 330 kglt (Cawse ore), whilst acid loading for Bulong ore was varied according to the presence of either reductant or oxidant. The extraction of both nickel and cobalt from limonite ore remained unaffected when small amounts of sulfkr were added, but addition of even small amounts of reductant to nontronitic ore decreased both nickel and cobalt extraction. Increased manganese and iron dissolution were observed as the levels of reductant increased, accompanied by a decrease in chromium dissolution. As the iron dissolution increased, free acidity decreased, with a subsequent decrease in nickel extraction. In contrast, addition of oxidant lead to reduced iron and manganese dissolution and slower extraction of nickel and cobalt. Keywords: Limonite, Nonhonite, Eh, Nickel Extraction

Jan 1, 2004

By C. H. Bucknam

Principles of Green Chemistry provide useful guidance for sustainable mineral process development. Laboratory bench scale testing was carried out using pregnant cyanide leach solutions, and a number of commercially available mercury precipitation reagents were compared using jar testing to determine the most efficient and selective reagents for mercury precipitation. The most efficient reagent identified was sodium polymeric thiocarbonate (NaPTC).Coagulation experiments with fine diatomaceous earth resulted in a stable precipitate, with good settling properties. On line monitoring of the mercury in solution is recommended for process implementation to conserve reagent removing approximately 90-95% of the mercury with minimal silver and negligible gold losses.

Jan 1, 2004

A mining companyÆs approach to managing the risk of theft of explosives and initiating devices should be underpinned by an organisation-wide policy developed with internal and external consultation. It should be based on the principles of sound proactive risk management, planning, monitoring and remedial action. This paper aims to provide mining (and construction)organisations with the rationale and many of the tools they need to control explosive security risks. As with all legislative compliance, they are best managed by incorporating the statutory and legal requirements into company policies, management systems and plans, operating procedures and culture. This is the approach that has been adopted in this paper. Trends we should expect: more prescriptive legislation and stricter government regulations; enhanced enforcement and more prosecution; more sophisticated detection systems, eg airports; additional compliance costs; additional vigilance on record keeping; improved risk awareness and risk communication; wider use of explosives policies, management systems and plans; and additional security staff with investigative skills.It should be noted that mining companies will be required to play their part in reducing the likelihood of explosives, intended for mining purposes, being wrongfully used to threaten, hold to ransom or to injure individuals or members of the public or to produce property damage. This will be done by putting in place safeguards to reduce the risk of theft of explosives while they are under their control. On that basis, this is a business risk assessment rather than a hazard risk assessment. A conclusion of this paper is that mining companies can and should play their part in reducing the supply of explosive materials that can then be used for illegal activities. In fact, mining companies have always had this duty, but now the stakes are higher û æcomplacency no longerÆ.

Jan 1, 2004