Search Documents

By Francis Kendorski

One of the most dangerous events in underground coal mining is unexpectedly encountering water inrushes from undetected abandoned mines in the same seam. The surest and most confident method is probe drilling either from the mine or from the surface. However, drilling is expensive and may even miss the suspected mine voids entirely by drilling through pillars. Many operators rely upon one or more of several remote sensing techniques for detecting mine voids. However, mine "voids" often are not air- or water-filled open cavities, but are collapsed, rubble-filled chimneyed columns in the strata. Geophysical techniques, such as seismic reflection and refraction, electrical resistivity, magnetics, ground-penetrating radar, and others, often assume a continuous or fractured rock mass that has varying properties which provide the signatures that allow discrimination of one strata from another, or of strata from voids. However, a rubble-filled cavity has rock block-to-rock block contact throughout its volume and can still respond as a continuous rock mass with the rock blocks allowing signal transmission or mass detection, rather than a void space. Hydraulically, a rubble-filled cavity is essentially as transmissive to water as an open mine void. Thus, the problem of detecting a mine void with confidence is significantly compounded.

Jan 1, 2004

By Yoshimasa Funakawa, Kazuhiro Seto, Akio Kobayashi

A new hot rolled high strength steel consisting of ferrite matrix and nanometer¬sized precipitates was developed. The ultra fine precipitates were identified as TiMoC2, and the strengthening by the precipitates was evaluated more than 300MPa in case of TS/800MPa grade steel. Due to the strengthening effect of the ultra fine precipitates, alloy elements for solid solution hardening can be reduced. It is notable that the steel shows very high yield strength (730MPa in case of TS/800MPa) and very high local elongation leading to excellent stretch flange formability at the same time. The mechanical properties of the steel are attractive for chassis parts and structural parts of auto body. The steel has been produced commercially, and applied to the parts successfully.

Jan 1, 2004

By R. Frank Chiappetta

A new blasting technique has been developed by International Technologies, LLC. to eliminate subgrade drilling, lower ground vibrations, improve fragmentation and reduce explosive consumption. The new technique utilizes a uniquely designed borehole plug, with a bottom hole air deck and a predetermined stemming mass on top of the plug. This combination is referred to as the Power Deck?. Single holes and full scale tests were conducted by Blasting Analysis International, Inc. (BAI) to determine how the system works, the mechanisms behind its success and the best design parameters to use for the given rock conditions. Results have shown reduced or eliminated subgrade drilling, ground vibration reductions of up to 33%, reduced explosive consumption by 16 to 25%, and improved fragmentation by up to 25%. This paper summarizes the methodology, field test setups, analyzes procedures and results for one series of single hole and full-scale tests which were performed in a Pennsylvania, USA quarry.

Jan 1, 2004

By V. G. c Papangelakis, M. Huang

A conductivity cell, developed previously, was employed in an effort to investigate the inter-relation between electrical conductivity and acidity of sulphuric acid - metal sulphate solutions at high temperatures. The measured solutions include the H2SO4-H2O, MgSO4-H2O, H2SO4-MgSO4-H2O, H2SO4-MgSO4-Al2(SO4)3-H2O solutions. All solutions reported in this paper were measured from 15 to 250 °C at equilibrium vapour pressure. The maximum measured concentrations of H2SO4, MgSO4 and Al2(SO4)3 were 0.45 m, 0.30 m and 0.10 m, respectively. It was found that, from 15 to 250°C, there is a linear relationship between H2SO4 concentration and electrical conductivities for acid concentration up to 0.45 m. At 250 °C and constant H2SO4 concentration, the solution conductivity drops with the increase of MgSO4 concentration. Lt is suggested that this drop is caused by a decrease in the concentration of H. Finally, an empirical model was developed based on the available measurements. This model has been tested against real laterite leach solutions where sulphuric acid and metal sulphates are dominant electrolytes. The average difference between the estimate acid concentration from this model and the one from titration was less than 5%.

Jan 1, 2004

By E. V. Konopleva, H. J. McQueen, V. M. Khlestov

In addition to increasing grain boundary area during hot working of austenite, the dislocation substructures create potential sites for nucleation of ferrite both at original grain boundaries and at transition boundaries between deformation bands. This development gives rise to a marked increase in the rates of nucleation, of growth and of transformation to ferrite. The combined net effect is product grain refinement that requires less stringent cooling between finish rolling and coiling; hence determination of the above rates would advance process optimization. The important control parameters are the preheat temperature (degree of homogenization), finishing temperature, strain (accumulation near finishing) and the extent of recrystallization after finishing. These effects vary greatly with steel composition; nevertheless, some general rules have been formulated. Moreover, there is also potential for deformation of the refined ferrite. There are other thermo-mechanical processes such as warm forming of metastable alloy austenite to provide a dense substructure that is carried into the martensite on quenching. In other processes, the austenite may be deformed during cooling through the transformation to develop a dense substructure in the ferrite that is stabilized by fine carbides.

Jan 1, 2004

By S. P. Taite, A. R. Charest, P. D. Lewis

The El Sauzal deposit is a classic, high sulfidation, epithermal gold system located in southwestern Chihuahua State, Mexico. The prospect was discovered by a Francisco Gold Corp. geologist in1995. El Sauzal was encountered as a result of an extensive grass-root exploration program in the rugged, dissected volcanic terrains of the Sierra Madre Occidental, around the historical Batopilas Silver Camp. At El Sauzal, high grade gold is hosted within a series of more permeable, low-dipping, lithic and fine-grained dacitic rocks of early Tertiary age. The mineralization appears to be both structurally and lithologically controlled. The alteration characteristics are typical of a high sulfidation system including kaolinite, illite, alunite, dickite and pyrophyllite. The deposit’s gold distribution, as recorded from drill-hole data and surface samples, varies from 0.2 to 650.0 g/t. The estimated geological resource, as calculated from an independent study completed in 1998, was 3.0 million oz @ 2.03 g/t including a minable reserve of1.8 million oz @ 3.3 g/t.

Jan 1, 2004

By K Niyomjinda, B Etschmann

Chatree Gold Mine is currently the only modern day gold mine operating in Thailand, and is situated approximately equidistant from Chiang Mai in the north and Bangkok in the south. Environmental guidelines set by the Thai authorities require Chatree Gold Mine to achieve a Total Cyanide level of 20 ppm or less in the process plant discharge slurry stream prior to release into the tailings storage facility. This paper describes both the initial difficulties faced in achieving compliance on this limit utilising the conventional INCO SO2/Air cyanide destruction system and the subsequent process improvements initiated to both the leaching process and the standard INCO process to achieve the current compliance levels of approximately 99/100 shifts. Improvements were focussed on the dual aspects of reducing the formation of WAD cyanide and ferrocyanide species in the leaching circuit coupled with process changes to improve removal of the ferrocyanide species from solution during the cyanide reduction stage.

Jan 1, 2004

By B. Simser, V. Falmagne

"Noranda’s Brunswick mine is a 10 000 t/d producer of lead-zinc-copper-silver ore that has been in operation since 1964. Mining of this multiple lens deposit is primarily by blasthole stoping techniques between 400 m and 1200 m below surface. The combination of a high overall extraction ratio, an overall steeply dipping tabular shape, and high horizontal stresses (twice the vertical) have elevated the induced stress regime to levels comparable to much deeper operations. Improved mine design, and a better understanding of how the rock mass responds to mining in high-stress environments is essential to improve overall recoveries and maintain safety. Seismic monitoring has proven to be an essential tool at Brunswick, for both short-term safety of workers, and long-term strategic planning.Practical case studies illustrate how seismic data, particularly source parameter information, can be used to measure the rockmass response to mining and improve mining layouts in difficult regions. As the global trend continues toward mining in deeper, higher stress environments (e.g., South African Witswatersrand Basin, Sudbury Basin) and as local extraction and thus ground stresses continue to increase in existing deposits, seismic monitoring will play a critical role in mining safely and economically."

Jan 1, 2004

By Seong-Taek Lim

Recently, 7xxx aluminum alloys have been evolved into new variants for thick semiproducts which have low amount of 2nd phases and low quench sensitivity. Commercial 7xxx alloys, especially in the thick forgings made of big ingots, often entail microstructural inhomogeneities and concurrent poor mechanical properties due to limited heating ranges and slower quench cooling. In this study, high strength aluminum alloy 7175 and 7050 are adjusted as an attempt to control the equilibrium phases (M-, T- and S-phase) to have optimum microstructure for the thick forging applications. The effects of the relative content of (Zn, Mg, Cu) on the evolutions of the coarse equilibrium phases, hardening response and resultant mechanical properties are investigated. Equilibrium phases (M,T,S) are evolved depending on the constitutional effect, primarily the change of Zn:Mg ratio, and cooling rate following solutionizing. The formation of the T- and S-phases is effectively controlled, and M-phases are homogeneously precipitated in the adjusted (dilute and high Zn:Mg ratio) alloys. It provides extended heating range and lower quench sensitivity than conventional alloys. The attempts ensure the microstructural homogeneity and improved properties, and is expected to be uniquely applicable in 7xxx thick forgings.

Jan 1, 2004

By R R. Anand

Recent research by CRC LEME from an Australian mineral exploration perspective, has focussed on regolith architecture and mechanisms of geochemical anomaly formation, within transported regolith. Methods have been developed for the rapid production of regolith-landform maps which is the starting point for understanding regolith architecture in the third dimension. Methods for development of 3D regolith models are less well advanced, and require integration of all available geological and geophysical datasets, but still with a heavy reliance on drill-hole information. The base of the transported regolith û the unconformity û remains the most important regolith boundary for geochemical sampling in transported regolith terrains. A new generation portable spectral logger, employing a broader spectrum can interpret important features from drill chips within the regolith. This allows internal architecture, redox fronts and the all-important interface to be objectively identified. Transported lateritic components can provide vectors to mineralisation in depositional regimes. Palaeomagnetic and new radiometric methods which date individual phases of the regolith provide evidence of different episodes, each characterised by different geochemical dispersion patterns in transported regolith. Along with lateritic residuum, calcrete is prime sampling medium. Calcrete is probably enriched in gold through physical and biological processes, rather than straight chemical processes. In South Australia, the lowermost calcrete layer buried within the depositional regime, especially where it lies directly over the silcrete layer at the buried interface, is the desired sampling medium. Certain gum trees, with deep roots in transported regolith have been shown to record anomalous values of gold and basemetals in leaves, twigs and bark. Anomalous metals in acid-sulfate soil seeps can also provide a window through sedimentary cover in respect of mineralisation in the basement. A number of Yilgarn occurrences of gold anomalies in transported cover, strongly infer hydromorphic and biological mobilisation of gold. This inference is supported by micro-analyses of regolith mineral hosts in hardpans and mottled sediments, which show gold and pathfinder elements prefer to reside in goethite and specific types of clay minerals. This creates anomalies in specific mineral phases. However the inference that that these are sites of mobile or labile metal ions remains enigmatic. Similarly there is inconclusive evidence that selective extractions will provide an anomaly not otherwise detected by conventional total dissolution methods. Hydrogeochemistry is a promising exploration tool for basemetal exploration. The importance of microbes in both the dissolution and precipitation of gold in the Australian regolith is demonstrated. We are on the verge of identifying the functional gene sequence of individual active microbes. A consideration of possible mechanisms for creating anomalies in soils above transported regolith, presents difficulties in facilitating upward movement of ions from the watertable to the surface. Perhaps the best avenues of research lies with surrogate soil gases, and biotic transfers.

Jan 1, 2004

By Nobel Insurance Service

[Executive Director’s note: ISEE is committed to continuing its efforts to ensure that blasters be made aware of the issue of migration of carbon monoxide resulting from blasting operations. In the July/August 2001 issue of the J o u rnal we printed excerpts from “Carbon Monoxide - The Silent Hazard,” an article from the Safety Update, published by Nobel Insurance Services. We also re minded readers of the text from the 17th edition of the ISEE Blasters Handbook in its section on trench blasting as follows: “...consideration must be given to the proper venting of gases generated from the blasting. Should those gases spread laterally rather than vent directly to the surface, the gases may travel underg round and finally vent well outside of the planned area. Such events may be caused by the strata, soil conditions or root systems, or existing and/or abandoned utilities or other man-made structures. In the worst situation, gases resulting from the detonation such as CO2, CO, and/or N Ox may travel through the strata and find their way into basements of nearby homes or businesses.” While incidents are rare, a number of cases in re c e n t years have resulted from outdoor blasting operations p roducing carbon monoxide gas that has migrated t h rough the earth and accumulated in nearby enclosed spaces. T h e re are steps that a blaster can take to be proactive in preventing incidents. These steps and studies of the occurrence have been expertly presented in several papers presented at ISEE conferences and included in the ISEE Conference Proceedings, available th rough the Blasters Library. In addition, Material Safety Data Sheets provided with explosives used in surf a c e blasting should provide additional information on gases p roduced by detonation. Below, we have reprinted the IME white paper, entitled “Fumes from Blasting Operations.” The paper underscores the unique set of circumstances that combine to contribute to high concentrations of CO measurements in underground, enclosed spaces following the detonation of explosive materials and provides recommendations to blasters

Jan 1, 2004

By R. Loney, M. Militzer

There is a significant demand for new high strength steels with fine grain sizes for structural applications. One approach in this regard is to develop hot-rolled HSLA steels where refining the microstructure leads to increased strength levels, e.g. 700 MPa yield strength, that can be attained by suitable modifications of chemistry and processing. Here, an HSLA steel is investigated that contains 0.05wt%C-1.65wt%Mn-0.20wt%Mo¬0.07wt%Nb-0.02wt%Ti and approaches the above strength class. The ability to control and predict the mechanical properties of hot rolled steel depends strongly on the thermomechanical processes, which the steel undergoes. The final microstructure and, thus, the properties of the hot-rolled steel are a function of the austenite decomposition obtained during accelerated cooling on the run-out table and precipitation during coiling. The austenite-to-ferrite phase transformation under run-out table conditions has been investigated using a Gleeble 3500 thermomechanical simulator equipped with a dilatometer. The effects of cooling rate and initial austenite microstructure including the degree of work hardening on austenite decomposition kinetics and ferrite grain refinement have been quantified. Results show that grain refinement can be optimized by the presence of work hardened austenite and accelerated cooling. Based on the experimental results, a model is proposed to predict the transformation start temperature and the resulting ferrite grain size for run-out table cooling conditions.

Jan 1, 2004

By Christopher Mark

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as "The UCS" for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: ? Brereton Limestone above the Herrin 6 seam (Illinois) ? Turner Mine Shale above the No. 9 Seam (Kentucky) ? Sandstone above the Eagle Coal (West Virginia) ? Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechnical exploration programs.

Jan 1, 2004

By Neil R. Burns, Michael Doggett

Abstract - The Nanisivik mine offers a unique opportunity to examine the economics of a mining scenario from its original feasibility study through to closure. In the early 1970s, the Strathcona Sound project (exploration around the Nanisivik mine) had advanced to the point where a significant mineralized body had been defined and a feasibility study was initiated. The study supported development of the Nanisivik mine, with government investment in regional infrastructure, and the mine was constructed and operated for 26 years. Many elements of the feasibility study were difficult to estimate because the project was unique in its high Arctic setting. As a result, many differences were found when comparing the actual mining data to the feasibility study. The majority of these differences were the result of an actual mine life of 26 years instead of the planned 12.5 years. Most of the mining costs were higher than estimated and production occurred at a much higher extraction rate than planned. On a constant dollar basis, the metal prices were, on average, below the feasibility estimates. For the most part, these differences balanced out, with the actual mining being only slightly more profitable than anticipated in the feasibility study.

Jan 1, 2004

By Maria I. De Rosa

Table 19 and figure 7 show the number of fires and fire injuries for surface metal/nonmetal mines by state during 1990-2001. Table 19 also shows the injury risk rates, employees' working hours, and lost workdays. A total of 79 fires occurred in 16 states during 1990-2001 for these mines. Forty-five of the fires caused 44 injuries and 2 fatalities (including 9 fires and 7 injuries involving contractors). The yearly average was 6.6 fires and 3.7 injuries. Sixty-five fires with 31 injuries and 2 fatalities occurred at metal mines, and 14 fires with 13 injuries occurred at nonmetal mines. The Ewhr value was 546 x 106 hr (In = 0.016), and the LWD value was 13,134. Nevada and Arizona had the most fires (19 fires, 10 injuries, and 1 fatality; and 19 fires and 11 injuries, respectively). They were followed by Minnesota (11 fires, 4 injuries, and 1 fatality) and Alaska (6 fires and 4 injuries). Of these states, Alaska had the highest injury risk rate value (In = 0.079). Table 20, partly illustrated in figure 8, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays by time period. The number of fires increased during the second period, then decreased during most of the remaining periods. The number of fire injuries decreased during most of the periods (a small increase is seen during the last period), accompanied by a decline in employees' working hours during most of the periods (a small increase is seen during the third and fourth periods). The In values follow patterns similar to those shown by the number of fire injuries. Tables 21-26 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 9 shows the major variables related to fires for 1990-2001. Table 27 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By H. Pei

PZH (Pan Zhi Hua) Iron and Steel (Group) Corporation, the biggest steel company in southwest China, has been using titanium-vanadium-magnetite as the main raw materials for blast furnace iron making processing for over 30 years. One of the problems that has a negative affect on the blast furnace operation is slag foaming. Based on the chemical components of the blast furnace slag-bearing higher TiO2, the foaming properties were studied. The TiO2content, which is calculated according to the total titanium content in all the forms of titanium compound in the slag, in this research is 30% weight per cent. Different forms of titanium compounds have different actions on the slag foaming behaviour that depends on the reduction condition in the blast furnace. The relationships among slag foaming performance and the binary alkalinity of the slag, the content of CaF2, MnO in slag, and the amount of gas injected in slag are investigated. The results show CaF2 and MnO have a stronger anti-foaming affect on the slag, even in the lower percentage. The way to measure high TiO2slag foaming performance and how to eliminate foamy slag are also discussed. Keywords: blast furnace slag bearing TiO2, foamy slag, foaming performance

Jan 1, 2004

By J. P. Thomson

Magnesium alloys are steadily improving their market share as structural components especially in the transportation sector. Therefore, there is a great deal of interest from the automotive and the metal casting industry to develop viable economic casting processes for magnesium-base alloys. This paper summarizes the preliminary results on the continuing projects within CANMET-MTL on casting processes such as gravity and low-pressure casting in sand molds, permanent molds and lost foam.

Jan 1, 2004

By J Morton

The Resource Management Act 1991 represented an innovative and unique piece of planning and environmental legislation when it was introduced. Since the Act was passed into law in 1991 it has been subject to nine amendments, many of which were of the ætinkerÆ variety. These amendments recognise that the Act has not been as successful in providing the æone-stop shopÆ for resource users that the Act was hoped to be. The latest and most significant attempt at changing the Act was the Resource Management Amendment Act 2003. The amendments made by the Amendment Act have proved to be largely unsuccessful in achieving any significant changes to the way resources are managed in New Zealand, and have failed to address many of the concerns which drove the original Resource Management Amendment Bill in 1999. The recent decision to discontinue further investment in Project Aqua has once again placed the Act in the spotlight as a significant hand-brake on major projects. This particular event has led to yet another review to be undertaken this year. The review will focus on five key areas:   1.   achieving the right balance of national and local interests; 2.   improving the design and process for local policy formulation; 3.   improving the consent decision making process; 4.   allocation of natural resources (water, air and geothermal); and 5.   supporting measures for building capacity and promoting best practice and implementation at the local authority level.  It is important for the business community and the mining industry in particular to seize the opportunity that this review provides to make sure that any amendments undertaken as a result of the review achieve the aims listed above. The review needs to be considered in light of the current regime for the management of natural resources in New Zealand. In addition to the Resource Management Act 1991, the Crown Minerals Act 1991 and the Building Act 1991, which form the core resource statutes in New Zealand, there have been other developments affecting the regime. Special legislation over and above the Resource Management Act 1991 has been enacted to protect the Hauraki Gulf and special legislation is currently being considered to protect the Waitakere Ranges in Auckland. In the Hauraki District mining is prohibited in some areas and a plan change mechanism is specified as the appropriate tool to use in the event a mineral resource is to be developed in those areas. The current review is a further opportunity to remedy the inadequacies of the Act.

Jan 1, 2004

By H. J. H. Pieterse

Agitation requirements in oxidation autoclaves can vary widely depending on the mineralogy of the feed material and the specific process selected. Before selecting an agitation system it is important that the client specify the desired throughput, mineralogy, chemistry, kinetics, compartments, overall retention time, and the desired oxygen utilization. In selecting the agitation system, the factors mentioned above as well as oxygen solubility, oxygen mass transfer coefficients, and specific power are evaluated. Much research effort has been directed toward open tank systems for fermentation and oxidation processes. However, for high pressure autoclave oxidation processes little information is available. In this review the author's experience in the autoclave industry and some of the available literature are utilized to compare the installed power per unit volume with some of the methods proposed for open tank oxidation. Equations that appear to give results close to that experienced in the industry have been identified. Further work is required in this area to develop a higher degree of confidence in the ability to predict the power required for any given case.

Jan 1, 2004

By H. Urata, K. Ishii

To determine the effect of F ions in the molten alkali silicate systems on their structures, quenched Na2O-SiO2-NaF systems were investigated by Raman spectroscopy and molecular dynamics simulation. The systematic increase of 1100 cm-1band intensity in the Raman spectra of the silicate melts accompanying the replacement of F for O provides the evidence for concomitant polymerization of melts. From the molecular dynamics simulation, it was confirmed that most of substituted F was mainly coordinated to Na+ ions but not Si4+ions. These results were consistent with the mechanism in which F associated with otherwise network-modifying Na rather than with network-forming Si. Since F was associated to Na+ ions, the replace of O ion by two F ions promote the polymerization of silicate melts. Keywords: fluorine; molten flux; slag structure; molecular dynamics simulation; Raman spectroscopy.

Jan 1, 2004