Search Documents

By Seung-Kyu Son

This study was investigated about physico-chemical parameter such as water temperature, salinity, inorganic nutrients and total organic carbon (TOC). CTD (Model: Sea-Bird 911 Plus) castings were carried out on two transects in the northeast equatorial Pacific Ocean. As a part of the Korea Deep-sea Environment Study (KODES), inorganic nutrients and TOC were determined at 41 stations located from 131° to 136°W along 10.5°N and from 17° to 5°N along 131.5°W (Fig. 1). We particularly chose KODES Long-term Monitoring Station (St. KOMO) to observe for the annually environmental baseline study in the contract area. [ ]

Jan 1, 2005

By L. Bichler

Utilizing thermal analysis techniques, pioneering research into the solidification mechanism of a popular magnesium alloy AZ91E cast by the Lost Foam Casting (LFC) process was carried out, Foam characteristics, section thickness and application of vacuum were seen to have profound effect on the cooling rate, thermal gradients and casting temperature profiles.

Jan 1, 2005

By J A. Cowburn

The high intensity zone within the Jameson Cell is the downcomer. It is largely external and separated from the flotation tank. This, together with operation of the downcomer under vacuum, rather than at elevated pressure and the absence of moving parts, allows ready access to the high intensity zone for measurement and analysis. Experimentation was conducted allowing measurements of recovery for residence times of between 20 milliseconds and ten seconds within the downcomer of a Jameson Cell. The affect of aeration rate on the recovery of different particle sizes was also studied.

Jan 1, 2005

By Antonio Peralta, Guillermo Dante Ramírez-Rodríguez

Mining is generally considered a large-scale hightech industry. However, it has estimated that about 12 million people, about 30% of the world’s total mining workforce, relied on small-scale mining for their livelihoods. During the years, the large-scale mining industry has developed best practice environmental procedures, which have been applied in diverse settings through the world. In contrast, small-scale mining is better known for its high environmental impact and the lack of safe and healthy working conditions. This paper will discuss the environmental control strategies used by the large-scale mining industry, and its applicability to small-scale mining in developing countries.

Jan 1, 2005

By M. Greyling, C. Panaou, M. Bellino

Commonly the most frequent method of calculating the overall mass balance of a multi mineral platinum-group metal (PGM) concentrator circuit in Southern Africa has been through the use of spreadsheets, typically Microsoft EXCEL®. While there are some advantages in using spreadsheet based mass balances during the conceptual design phase of the project, their use becomes limited in the detailed design phase of the project. This paper discusses the successful application of METSIM® for mass balancing of a PGM concentrator and highlights the benefits gained during the conceptual and design phase of the project.

Jan 1, 2005

By Andrea Gambi, Giancarlo Olivucci, Maurizio Lenzi

"In the paper a criterion for the evaluation of the sharing of the lateral loads in a piled foundation is presented. It relies on the the compatibility condition between the rotation of the rigid pile cap and the rotations of the pile heads, following in that the criterion suggested by the Eurocode 8 - Part 5. This assumption leads to an analytical solutions which allows to deal with the sharing of the lateral loads and moments by means of two main interaction parameters only. A sharing domain is also derived and it shows the role played by the eccentricity of the lateral load on the values of the axial forces and of the bending moments at the head of the piles.INTRODUCTIONIt is well known that the interaction among soil, piles and foundation is one of the most complex subject to deal with in Geotechnical Engineering. Its rigorous study needs to employ suitable finite element software nowadays available and able to take into account the non linear behavior of the soil as a continuum and the inelastic response of the structure. A deep insight to the topic of the sharing of the loads cannot obviously renounce to this approach.On the other hand it is a daily need of the designers to have at their disposal simple tools that allow to make preliminary evaluations of the basic equilibrium conditions. To this purpose many methods of analysis have been developed in the past to face the sharing of the loads in a simplified version. The present contribution follows this way trying however to introduce some improvements that leads to find a solution that satisfies both the equilibrium of the forces and the compatibility of the movements (Lenzi, Gambi, Olivucci, 2002). The proposed model allows to identify the basic parameters which govern the sharing of the lateral load and it allows to perform also parametric analysis and quick checks that may be useful in the design of the piles."

Jan 1, 2005

By S. S. Jenkins Jr.

While the method is seldom used anymore, coyote blasting is an historically interesting way to blast large quantities of rock. It was used extensively in the days before modern fast drills were available and can be very effective in some formations that have a natural breakage pattern. This paper will cover the general principles, some blast design factors and point out several actual blasts including some very large ones.

Jan 1, 2005

By Daniel Journeaux

Introduction Daniel Journeaux is President of Janod Incorporated. Janod is a family owned and operated company that has been working in the field of slope stabilization since 1970. Daniel has worked in the rock stabilization industry for 25 years and has been President of Janod since 1992. Daniel has been an invited speaker for the Federal Highways Administration for the Northwest and Southwest divisions, Queens University in Kingston Ontario, The University of Laval, Vulcan Materials Company, CSX annual meeting for the Northeast Division. Daniel has written several articles and has been published in Pit and Quarry, World Tunneling, and American Shotcrete Association magazines. What is Required to Remediate Highwalls There are several techniques available to stabilize highwalls or temporary rock walls to allow for safe mining practices. The following are some of the techniques that can economically be used.

Jan 1, 2005

By A. Krishnan

Keywords: Tantalum extraction, SOM Technology, inert anode, membrane stability The Solid Oxide Oxygen Ion conducting Membrane (SOM) technology offers great potential for environment friendly and energy efficient extraction of high-energy content metals. This work was performed to demonstrate the technical and commercial viability of the technology to produce tantalum metal directly from tantalum oxide and ore concentrates using a solid-oxide, oxygen-ion-conducting membrane (SOM). The process can be used to efficiently produce tantalum metal without expensive pre-processing of raw materials and without harmful by products. The work reported in this paper is: the proof that high purity tantalum metal can be produced, study of the electrochemical behavior of the cell and the method to increase membrane stability.

Jan 1, 2005

? Develop a six year capital budget for future emission controls at Western Springfield Power Plant that would provide long-term operating certainty

Jan 1, 2005

By Michael R. King

The application and use of steel fibre reinforced concrete in precast tunnel lining design is a growing trend due to its advantages in performance over plain concrete, and ease of manufacture compared to traditionally reinforced concrete. However, the design process and performance characteristics of the material are poorly served by current codes and standards. This paper provides some basic design guidance for segmental linings, and compares the material properties for the different material options. A typical example is considered to compare the possible results of lining arrangement and thicknesses for a plain, reinforced, and fibre reinforced design solution.

Jan 1, 2005

By J E. (Boet) Coetzee

SAFEX International, as the name suggests, is a global organisation, which has the fundamental objective of improving the safety of operations concerned with the manufacture, storage, transport, and use of commercial and military explosives and pyrotechnic products throughout the world. It is a nonprofit making organisation of manufacturers of explosives from all parts of the world, founded in 1954 with the aim of exchanging experiences within the explosives industry. Every third year SAFEX organises a Congress during which members present papers on selected themes and discuss reports of significant incidents that occurred since the previous Congress. Admission is for SAFEX members only, thereby creating a safe environment for discussing problems “within the family”. The XV Congress will celebrate the Association’s 50th anniversary in Geneva where it was founded. An overview of the Congress indicates its structure and covers aspects such as the training event, technical seminars and the themes for the plenary sessions and associated workshops. The paper also highlights the special event for the chief executives of member companies and the review of incidents that occurred in the industry since the last Congress. The Congress concludes with a social programme for delegates and their partners on the last day.

Jan 1, 2005

By H. J. Le Roux, W. B. Drummond

1. INTRODUCTION We have a moral responsibility towards the world to reduce the harmful deposits we emit into the environment arising from beneficiation technologies. Industry has not willingly spent money to limit these emissions because it affected their profit margin with the end result of emitting harmful elements into the environment. Governments have thus rightly stepped in and enforced systematic reduction of these emissions through legislation. In the past beneficiation of sulphur bearing ores was typically done through hydro-metallurgical concentration, smelting, followed by Sulphur removal by converting processes like the Pierce Smith converter. The latter two processes emitted substantial quantities of Sulphur into the atmosphere. Spiralling costs and legislation have resulted in the quest to develop more efficient and environmentally friendly processes to achieve the same end results. New hydro-metallurgical processes like the ActiVox process has completely eliminated the pyro-metallurgical processes. Kansanshi are also operating a similar process. It however elicits other ground water and spillage pollution hazards and problems of it?s own. Various improvements has also been made to the pyro-metallurgical stages, examples being combined smelting and converting with the Noranda reactor, the Codelco CMT furnace, one step flash smelting/converting or the Mitsubishi continuous smelting, converting and slag cleaning process. The new converting processes are also normally enhanced using oxygen leading to higher SO2 gas strength with only a marginal increase in off-gas volume. These processes have led to better efficiencies and a more controlled environment that reduces pollution, but does not eliminate it completely. The fact that there are still more than 70 existing Pierce Smith converter plants throughout the world that needs to be replaced or upgraded at tremendous capital cost, means that we will have the environmental problems for some time to come. The need thus exists to cost effectively get these existing plants into a state where they meet the new environmental regulations, community and safety requirements. This paper will concentrate on just one aspect of this quest, i.e. reduction/removal of off-gasses emanating from the converting of non ferrous sulphur mattes to achieve higher or specialised grades of refined metals.

Jan 1, 2005

By H. Lachmund, R. Bruckhaus

At Dillinger Hüttenwerke/Germany steel production of grades for linepipe applications especially for sour service has a long tradition. The BOF process after replacement of the vessels is optimized by a newly developed lime addition model and variations in lance tip geometry. Equipped with three state-of-the-art VOD tank degassers metallurgical requirements of lowest contents of e. g. sulphur, nitrogen and hydrogen can be achieved. Three continuous casting machines of vertical bending type with solid core even improve already high levels of cleanliness. The vertical part corresponds to the metallurgical length of 12 to 15 m and therefore assures a maximum of cleanliness after solidification before bending. Slab thickness up to 400 mm can be produced with model controlled dynamic soft reduction. The accurate alignments of the casters assure minimized segregation and microporosity. Surface and internal cracks can be avoided by special cooling, bending and straightening strategies.

Jan 1, 2005

There are many ways to classify structural slurry wall elements, but the DFI committee chooses to limit these descriptions to three functional requirements, namely: design function, plan configuration and type of panel reinforcement. (See Figure 1 in Part IV for panel classification). Slurry walls can function as: 1. Curvilinear or linear elements for temporary and/or permanent structures to resist lateral forces transferred from the ground, water, earthquakes and various surcharge loads. 2. Load bearing elements in various plan shapes to resist vertical forces. 3. Combination Elements to resist combined forces under conditions 1 and/or 2. For example, elliptical shafts with various openings for tunnels and conduits have been commonly used for deep excavations.

Jan 1, 2005

By I Ross

The ground handling system needed for the second lift of the underground block caving operation at Northparkes Mines had to link into the existing infrastructure. Production requirements indicated that an annual output of 5 Mtpa was necessary from a depth of approximately 850 m. The shaft that serviced the first lift stopped at a depth of 520 m. This paper covers the selection of the design for the system and the factors that were taken into consideration in making the decision. It will describe the installation program and methodology and highlight areas of significance and then detail some of the issues concerning commissioning of the ground handling system.

Jan 1, 2005

The Health Tracking project is one of five projects being undertaken as part of the Minerals Industry Cooperation Initiative (MICI) û a national initiative sponsored by the Minerals Council of Australia. The aim of the Health Tracking project is to assess the practicality of ways to demonstrate the monitoring of hazardous exposures and the occurrence of related occupational illness and disease and development of management systems and strategies at a national level. This second stage of the project will be completed in 2005 and will cover four areas: pilot development of a comprehensive job exposure matrix (JEM) for the minerals industry; development of both proactive and reactive occupational illness and disease metrics; recommendations regarding appropriate health tracking models; and provision of best practices guidelines for management of occupational health. The synergies between these areas will establish the path towards an effective national occupational health surveillance system and the development of effective prevention strategies and policies.

Jan 1, 2005

By F H. Henrfquez, A G. Oroz

Design and operating conditions of large size mechanical flotation cells were evaluated by comparing them with actual operating conditions in a plant. The objective was to determine the time scale-up factor, typically based on empirical rules. Experiments were conducted on the rougher flotation circuit at Minera Escondida Ltd. The circuit consisted of self-aerated mechanical cells of 160 m3, arranged in six parallel banks with nine cells each. The rougher circuit flotation kinetics were evaluated from direct sampling and local mass balances around each cell of the bank. Adjusted overall mass balances were also developed. This information was used to fit different kinetic flotation models, and it was found that the rectangular distribution function was the most appropriate to describe the distributed rate constant for industrial operation. Then, a rougher flotation simulator was developed to describe the actual operation in terms of the operating variables (mass flowrate, solid percentage, feed grade) and the actual volumetric flowrate entering to each cell. In this study feed pulp samples were taken in parallel from the rougher circuit and were simultaneously floated in the laboratory. The kinetic behaviour was then modelled at a laboratory batch scale in order to determine the time scale-up factor between laboratory batch flotation data and industrial size flotation. The time scale-up factor observed for large sized cells, 160 m3, was found to be reasonably similar to those previously determined for self-aerated mechanical cells, but of lower size, operating at similar recoveries. In addition, the relative effect of mixing, between laboratory batch and an industrial flotation bank, was quantified by the parameter, separating the impact that kinetic and mixing changes have on the time scale-up factor. In general, the rougher flotation operation was found to reach the predicted metallurgical target, and the optimal separability criterion was also respected. The diagnostic generates information about the internal state of the process and helps to identify potential improvements for design, operation and control of the circuit.

Jan 1, 2005

This paper contends that optimisation of energy resources through active control and predictive simulation modelling is possible, and that such monitoring leads to large savings in the electricity costs of hot mines (where refrigeration has to be employed). In addition, active monitoring and control can positively affect the establishment of a safe, healthy and productive working environment. In the entire optimisation process certain guidelines were set to ensure that the requirements of the Mine Health and Safety Act were met (South Africa). Varying the quantity of air supplied underground by means of variable speed drive (VSD) fans is one of the crucial factors in the interactive approach towards the optimisation of ventilation, as is refrigeration and the pumping requirements associated with refrigeration. This article highlights the interaction between the amount of air supplied and the effect it has on refrigeration requirements underground. This article also considers the effect that this would have on contaminant control. Various tools are available for ventilation and cooling design for mining. A lot of these tools are based on the assumption of steady state conditions and do not take into account instantaneous changes in conditions, day-to-day, or hour-to-hour (such as for temperature and contaminants). They also do not take into account the optimisation of energy resources related to the creation of the acceptable underground conditions. With these tools worst-case and best-case scenarios are identified, and strategic decisions are made accordingly. Currently, the amount of the fresh air, the velocity of the air, and its general temperature in the mine are only changed when one production phase changes into another (or when unacceptable conditions occur as a result of poor design or neglect). This means that during a specific production phase (which can last for several months), there can be an oversupply, or undersupply, of energy resources, which will obviously affect the concentration levels of the various contaminants (through under or oversupply of air).

Jan 1, 2005

By Don Phelps, Dean Brox, Peter Procter, Andy Saltis, Tom Morrison, Jeff Pringle

The Greater Vancouver Water District is currently constructing the Seymour-Capilano Water Filtration Project to enhance the quality of drinking water in the Vancouver metropolitan area. The Seymour-Capilano Water Filtration Project comprises the 1,800 million litres per day Seymour-Capilano Filtration Plant, the 1,080million litres per day Capilano Pumping Station, twin tunnels with associated shafts, and the Capilano Energy Recovery Facility. The twin tunnels will convey raw water under pressure from the Capilano Reservoir to the Seymour Filtration Plant and return treated (filtered) water for distribution. The Twin Tunnels component of the project comprises twin, 3.7 m diameter, 7.2 km TBM bored tunnels, the 180 m deep Seymour Shaft as the main launch shaft, and two 4 m diameter, 268 m deep raise bore exit shafts at Capilano. The Twin Tunnels have been planned as predominantly unlined tunnels sited at depth entirely within granitic bedrock and cross under two major buried glacial valleys of breadths in excess of 1500 metres that are filled with glacial sediments to depths up to 200 metres. The maximum overburden along the tunnel alignment is approximately 400 metres. Comprehensive site investigations and studies were completed during the detailed design stage of the project. The construction of the twin tunnels started in the fall of 2004 and is planned to be completed by mid-2008.

Jan 1, 2005